I've been asked to configure mac-address filtering on our WLC 4402 and it was basically straight forward. however i noticed that in creating the filter you can only choose 1 SSID or the other option would be to choose all? My question then is what happens if i need a user one 2 specific SSIDs? can i create separate filters for each SSID but using the same mac?
View 1 Repliesl have implemented mac filtering auth on my wireless network, l have 2 WLC ( 1 WLC 5508 and 1 WLC 4402, and I wonder if you can migrate the mac address database of a WLC to another and how can l do this.
View 4 Replies View RelatedWhen disabling SSID broadcast and enabling MAC address filtering on WAG320N, my other wireless laptop get disconnected. And when you try to connect, it doesn't connect again.
View 3 Replies View Relatedwe use wlc 4402 (Software Version 7.0.98.0) and want to allow only several wlan nic vendors to connect to a wlan ssid.According to this, is it possible to configure MAC Filtering with wildcards, e.g. aa:bb:cc:* ?
View 1 Replies View Relatedwe have a 4402 controller with sw 7.0.116 and a wcs with sw 7.0.172.
We have to create a new wireless network, and would like to send the ssid to only one AP. Is this possible ?
In the company we have two SSIDs for corporate and guest networks respectively when I try to connect to any of the SSIDs it doesn't happen until 5 retries. The only log I get that seems to be related to it is the following:
*Jun 11 11:48:09.062: %APF-1-DISCONECT_MOBILE_DUE_TO_WLAN_SW: apf_policy.c:541 Disconnecting mobile 00:23:32:73:d7:15 due to switch of WLANs from 1(femsawl) to 2(visitas)
Here it shows a switch between SSIDs but if you just turned on an apple device and try to associate for the first time to any of the SSIDs the scenario is the same, several tries to connect.I am running a 4402 wlc with 6.0.202.0 software version.
I just upgraded to the Belkin N750 DB router from the version just below it and couldn't get the wireless card (Ralink RT2760) in my daughter's dual-boot WinXP/Ubuntu 10.04 to connect to the WPA security setting (WEP only) on the Ubuntu side. There is an updated driver, but it's way above my Linux skill set, so instead I just disabled security completely, and used the MAC Address filtering to add all of our household devices.This solved her connection problem, but I am wondering if there is any danger to this method that I might not have considered
Originally Posted by BelkinMAC Address FilteringThe MAC Address Filter is a powerful security feature that allows you to specify which computers are allowed on the network. Any computer attempting to access the network that is not specified in the filter list will be denied access. When you enable this feature, you must enter the MAC address of each client on your network to allow network access to each. To enable this feature, select "Enable MAC Address Filtering". Next, enter the MAC address of each computer on your network by clicking "Add" and entering the MAC address in the space provided. Click "Apply Changes" to save the settings. To delete a MAC address from the list, simply click "Delete" next to the MAC address you wish to delete. Click "Apply Changes" to save the settings.
I have two WAP 321 devices set up in our building they are on the same subnet with the same SSID and are using the WDS bridge mode. My question is, if i enable mac-address filtering on one of these devices will this infomation be passed to the other bridged device? or would the allow/deny list need to be populated manually on each device?
View 2 Replies View Relatedi am using two Cisco AP 4410N series in my network .Wants to use MAC address Filtering but it supports only 20Nos of MAC to add in the AP.
Is there any way like IOS upgrade the AP supports more MAC Address to add.
I'm attempting to block about 10 to 15 users on the wireless by using MAC address filtering on the Aironet. I referenced the following link: URL,The policy does indeed work, but once I apply the filter all traffic on the wireless for that particular VLAN stops. Why would this happen? I wouldn't think I need to configure anything else for this to work, but maybe I'm wrong.I was looking over the config and I noticed that each time I added a MAC address to the filter, it would create and access-list 701 deny 0000.0000.0000 ffff.ffff.ffff Once I removed this access-list, traffic starting flowing again, but when I add another MAC address the access-list shows up again.
View 15 Replies View RelatedCAn we filter MAC address in LAN using ASA 5520 , whats the method ?
View 2 Replies View RelatedDoes ASA 8.3 support MAC address filtering, I want to allow a single specific laptop to login to the ASA 8.3 firewall (for management) from anywhere on the internet, I know I can do it through VPN but I want a simple MAC address access list or something......
View 3 Replies View RelatedHow does MAC address filtering secure a network?
View 9 Replies View RelatedI have had a great experience with my old DIR-655 (rev A) router. However, I would like to upgrade to a newer and better D-link router for my home that contains many well-connected children. Which routers are like my DIR-655, and have better overall performance than the DIR-655 without necessarily using the benefit of the 5 GHz second band. What better performing routers can record more than 24 MAC addresses in the Network Filtering area? I understand many people don't agree with MAC address filtering, but I like it to keep my kids from giving out my network password to all the neighbor kids and their friends too. So, MAC address filtering works for me. Or, should I just get an updated version of the DIR-655?
View 5 Replies View RelatedI'm interested by the router Cisco RV180 or RV180W.
So as to increase security, i would like to set a MAC adress access restriction for all peripherals that would be connected to the router (10 computers, 2 servers, 6 Synology NAS) : only allowed MAC adress should access to the internet and network ressources.
Does the Cisco RV180 or RV180W have an IP to Mac biding feature and a Mac adress restriction feature ? If yes, how many peripherals/computers can be set ?
For example, only 30 mac/IP adress can be allowed on my actual router and it is not enough.
I am planning to enable MAC address filtering (one port on 4510 & another 3560). I want to allow only that MAC address to communicate via that port with the rest of the network and internet.
4510 has PC connected and 3560 had polycom connected. [code]
I have two wlc 4402 to control 50 AP 1131. 2 WLC: wlc-01 and wlc-02, wlc-02 config as backup wlc in the same mobility group. Client authentication:EAP with Microsoft IAS/AD.All AP have joined wlc-01. Wireless client work well with wlc-01.For testing I config access point AP01 have primary wlc: wlc-01, secondary: wlc-02 If I change config of AP01 like this: primary wlc: wlc-02, secondary: wlc-01. Client is hard to connect to wlc-02 and it only connect when client set static ip ALL wlc run this softwar image: 7-0-98-0 Should I send wlc-02 to warranty service?
View 8 Replies View RelatedMy DIR-655:
Hardware Version: A4
Product Page: DIR-655
The problem is that Website Filer doesn't work if on STEP 3: SELECT MACHINE of Access Control the machine was selected by MAC address. When the machine was selected by IP everything is fine.The problem is that IP addresses are assigned dynamically, so how to make sure that the policy would be applied to the same machine?
It shows this option "Filter wireless clients: Apply MAC Filtering to devices that connect to the network via Wi-Fi. This is the normal usage of MAC Filtering. Filter wired clients: "However I don't see that option on the actual page. How can i enable Mac address filtering only for the wireless side?
View 7 Replies View RelatedI have a Belkin N150 wireless router. I have enabled MAC Address Filtering as an added level of security. However; whenever I access the router, and if I check that page; the check mark for the option to enable the filter is always blank.
I have checked the option, clicked Apply Changes, and logged out of the router. i went back in this morning, to check the security logs. (Looking like someone is trying to jump on my network) I didn't see anything there, but when I checked MAC Address Filtering; there was no check mark indicating that the filter was turned on.
I just want to allow specified computers wired access to the internet via the E1000 router. Here is the problem I am currently working on:
(1) Setup the E1000 unit to allow only one PC 'C1' (MAC: 91:E6:BA:25:91:58) wired access to the internet.
(2) Add another PC (unknown MAC address) to the LAN side of the E1000 unit and see if it is being blocked by the 'Access Restriction' policy that was setup.
(3) Can’t get the above done – the second PC is able to surf the internet although the policy is enabled.
Notes:(a) Ref: 'Access Restrictions' web page or see Page 26 in the User Guide .(b) The unit has the latest firmware already installed: Firmware Version: 2.1.01 build 5Dec 3, 2010.(c) The internet port of the unit goes to the ADSL modem in my house.(d) Unplugged the unit for 10 seconds as advised by one of your technicians, still no difference.(e) I can deny PCs, but the allowing only specified ones seems not to be doing anything.By the way, can the E3000 or E4200 do the above?
The browser-based settings utility for my E1200 can't setup MAC address filtering. I go to the "Wireless MAC Filter" page and enable MAC filtering.When I click the “wireless client list” button, a new window opens saying “IE cannot display the webpage”. This always happens when I have a wireless connection active.When there are no active connections, then IE properly displays the MAC address table, but it is empty since there aren't any computers connected to the router.
View 5 Replies View RelatedI have come across articles mentioning that URL Filtering can be implemented by using ASA 5505 with URL Filtering Servers. But Websense and other Web Filtering Servers are paid ones ? Are there any free solutions available ? What exactly is N2H2 ? The reason is I don 't want to increase the CPU utilization of ASA by implementing URL filtering within the device. If I have around 30 nodes which connects to the internet via a 2Mbps line through ASA 5505 and if I want to block around say 10 or 15 URLs , will it increase CU utilization beyond permissible limits ? Currently the CPU Utilization is around 10 - 15 . Here's the infrastructure setup .
------------------------------------------------------------
Nodes -->Switches-->ASA 5505-->Internet
-------------------------------------------------------------
I have an AP Aironet 1140 that have two (2) SSID: (ZDE) and (GUEST). Guest is working fine but ZDE is not giving IP addresses to users attached in this AP. I atached the sh tech of the Ap. From the configuration cisco guide of Aironet 1140 i understand that by default, access points are configured to receive IP settings from a DHCP server on your network. But i don´t know if i have to configure the dhcp server ip addres in the Ap, similar to the ip helper address in switches
Configuring the Access Point to Provide DHCP Service. These sections describe how to configure the wireless device to act as a DHCP server:
•Setting up the DHCP Server, page 5-22
•Monitoring and Maintaining the DHCP Server Access Point, page 5-24
•Setting up the DHCP Server
By default, access points are configured to receive IP settings from a DHCP server on your network. You can also configure an access point to act as a DHCP server to assign IP settings to devices on both your wired and wireless LANs.
The 1100 series access point becomes a mini-DHCP server by default when it is configured with factory default settings and it cannot receive IP settings from a DHCP server. As a mini-DHCP server, the 1100 series access point provides up to 20 IP addresses between 10.0.0.11 and 10.0.0.30 to a PC connected to its Ethernet port and to wireless client devices configured to use no SSID, and with all security settings disabled. The mini-DHCP server feature is disabled automatically when you assign a static IP address to the 1100 series access point. Because it has a console port to simplify initial setup, the 1200 series access point does not become a DHCP server automatically.
Is it possible to assign a single ssid to multiple interface groups by assigning the ssid to multiple AP groups?
I have buildings geographically dispersed that are configured with multiple vlans in interface groups so that I can maintain an addressing scheme of dhcp assigned addresses per building. Each building is also further grouped as AP groups. I'd like to know if by assigning the same wlan ssid to each of the AP groups, will I maintain addressing integrity for each building? I'm thinking it will work.
Do the buildings have to be outside AP range of each other to avoid problems?
5508 controller
7.2.110.0 code
6 buildings
6 interface groups
1 ssid
Setting up Web Filtering on Cisco881 sec K9 router using CCP.
At the moment every user on the domain got blocked by the rule that i set up on the Web Filter (just using the wizard and choose default category). What i want is to separate users so that specific user can have full access while other user get filtered by the category.
And Yes I want to configure this using CCP.
We have a Cisco 4400 series WLAN controller.When I go to the clients and view who is connected; I can also filter it. However it only lets me filter by mac address, ap, wlan profile, etc.
It does not have IP filtering. Is there a way to filter using IP? Basically I want to find a particular client with a certain IP that's connected to our WLAN.Also how do we block the client? If we deemed that person should not get access.
I have a 2621 with a WIC-1ADSL that connects to my ISP. Since the 2621 has 2 ethernet ports, I wanted to setup a network on the second ethernet port for testing things such as VPN into my network via my ASA5505. I have a DHCP pool set on the particular network but cannot get a client to get an address from the router. I think I might have an ACL that is blocking or need an ACL to allow bootp on the interface. Here is the config:
Building configuration...
Current configuration : 4144 bytes!version 12.3no service padservice tcp-keepalives-inservice tcp-keepalives-outservice timestamps debug datetime msec localtime show-timezoneservice timestamps log datetime msec localtime show-timezoneservice password-encryptionservice sequence-numbers!hostname r01!boot-start-markerboot-end-marker!security authentication failure rate 10 logsecurity passwords min-length 6logging buffered 4096 debugginglogging console criticalenable secret 5 SECRET
enable password 7 password
[code]...
When I try to get an ip address from a client, I never receive one. But when I issue dhcp server statistics, I can see packets hitting the interface:
r01#sh ip dhcp server statisticsMemory usage 14050Address pools 1Database agents 0Automatic bindings 0Manual bindings 0Expired bindings 0Malformed messages 0Secure arp entries 0
Message ReceivedBOOTREQUEST 0DHCPDISCOVER 68DHCPREQUEST 5DHCPDECLINE 0DHCPRELEASE 0DHCPINFORM 0
Message SentBOOTREPLY 0DHCPOFFER 0DHCPACK 0DHCPNAK 5
Could URL FIltering be implemented on Cisco ASA 5505-BUN-k9?i mean to block certain websites, like facebook, youtube, to block certain download files like .exe, .com .bat etc....Is there any extra license needed for this, or it could be done with the simple IOS ASA5505-bun-k9?
View 4 Replies View RelatedI try to implement the url filtering feature on a cisco 2811 router and whenever i enable the parameter map patterns the router retuns (after some time)
%Unable to compile obj regex.[code] The result is that the router blocks ALL webpages without giving a block page message.
I have recently upgraded my company's network significantly, and in the process removed our Cisco edge routers and firewalls (gasp!), and replaced them with another vendor who gave a better price point for the router.However, i was only able to get ONE edge router, whereas before I had two, so I want to recycle one of my old 2921's as a cold standby (in case the brown sticky stuff hits the rotating air distribution blades, and $other-vendor router dies).Trouble is, the 2921 does not, I believe, have sufficient system resources to take the full routing table we're getting from our two ISP's.What I would like to ask is people's thoughts on the best method for me to configure the BGP setup on the 2921 to do the following:
-Accept the default route from each ISP and discard *everything* else in the route table
-Modify our advertisement (ad prepend) out the "secondary" ISP to reduce the priority of traffic coming in over this link.
-Configure the OUTBOUND priorities so that the "primary" link is used by preference for outgoing traffic (which will effectively shut down the secondary link for outbound traffic
I am trying to block clients based on MAC addresses connecting to our Wireless Guest network.
My scenario is: We have 2 interfaces (corporate and a guest). Users are connecting to our guest network after they have automatically connected to our corporate network and logged into Windows. When they realise that things are not quite working in the way they want (access to servers etc...), they reboot and then find they cannot logon to the laptop at all. This is because the laptop has automatically rejoined the guest network and has no access to AD. I then have to locally logon to the laptop and remove the guest network.
It’s starting to become a bit of a pain as we are an educational establishment and... well... you would wouldn’t you
Hardware: WLC5508, Software Version 7.3
So far I’ve tried enabling MAC Filtering under “Security -> AAA -> MAC Filtering”, but found out that it’s a white list. The opposite of what I’m trying to achieve, but I like the fact you can link it to a specific interface.
I’m just looking at the “Disabled Clients” again under “Security -> AAA ->”, but think this is more a total ban as I cannot see a method at attaching it to an individual interface. I'm kindda stuck and my good old friend Google is not yielding great results.
I’m not by any means a wireless expert, so there is probably a better method. I would prefer to use the controller as a way of achieving this, but if you think I’m wasting my time and should be looking at a Windows Group Policy method then I’ll go with that?
I am trying to do content-filtering over ssl VPN (clientless) on ASA 5505. [code]
View 2 Replies View Related