Cisco Wireless :: WAP4410N AP To Use Mac Address Filtering

Jun 8, 2012

i am using two  Cisco AP 4410N series in my network .Wants  to use MAC address Filtering but it supports  only 20Nos  of MAC to add in the AP.
Is there any way like IOS upgrade the AP supports more MAC Address to add.

View 1 Replies


ADVERTISEMENT

Cisco Wireless :: WAP 321 Mac-address Filtering?

Nov 26, 2012

I have two WAP 321 devices set up in our building they are on the same subnet with the same SSID and are using the WDS bridge mode. My question is, if i enable mac-address filtering on one of these devices will this infomation be passed to the other bridged device? or would the allow/deny list need to be populated manually on each device?

View 2 Replies View Related

Cisco Wireless :: MAC Address Filtering In Aironet1130AG

Dec 29, 2011

I'm attempting to block about 10 to 15 users on the wireless by using  MAC address filtering on the Aironet.  I referenced the following link: URL,The  policy does indeed work, but once I apply the filter all traffic on the  wireless for that particular VLAN stops.  Why would this happen?  I  wouldn't think I need to configure anything else for this to work, but  maybe I'm wrong.I was looking over the config and I noticed that each time I added a MAC address to the filter, it would create and access-list 701 deny 0000.0000.0000  ffff.ffff.ffff   Once I removed this access-list, traffic starting flowing again, but  when I add another MAC address the access-list shows up again.

View 15 Replies View Related

D-Link DIR-655 :: Enable Mac Address Filtering Only For The Wireless Side?

Sep 3, 2011

It shows this option "Filter wireless clients:   Apply MAC Filtering to devices that connect to the network via Wi-Fi. This is the normal usage of MAC Filtering. Filter wired clients: "However I don't see that option on the actual page. How can i enable Mac address filtering only for the wireless side?

View 7 Replies View Related

Linksys Wireless Router :: E1000 / MAC Address Wired Filtering?

Jan 19, 2011

I just want to allow specified computers wired access to the internet via the E1000 router.  Here is the problem I am currently working on: 

(1)   Setup the E1000 unit to allow only one PC 'C1' (MAC: 91:E6:BA:25:91:58) wired access to the internet.

(2)   Add another PC (unknown MAC address) to the LAN side of the E1000 unit and see if it is being blocked by the 'Access Restriction' policy that was setup.  

(3)   Can’t get the above done – the second PC is able to surf the internet although the policy is enabled. 

Notes:(a) Ref: 'Access Restrictions' web page or see Page 26 in the User Guide .(b) The unit has the latest firmware already installed: Firmware Version: 2.1.01 build 5Dec 3, 2010.(c) The internet port of the unit goes to the ADSL modem in my house.(d) Unplugged the unit for 10 seconds as advised by one of your technicians, still no difference.(e) I can deny PCs, but the allowing only specified ones seems not to be doing anything.By the way, can the E3000 or E4200 do the above?

View 9 Replies View Related

Linksys Wireless Router :: E1200 Can't Setup MAC Address Filtering

Sep 12, 2011

The browser-based settings utility for my E1200 can't setup MAC address filtering. I go to the "Wireless MAC Filter" page and enable MAC filtering.When I click the “wireless client list” button, a new window opens saying “IE cannot display the webpage”. This always happens when I have a wireless connection active.When there are no active connections, then IE properly displays the MAC address table, but it is empty since there aren't any computers connected to the router.

View 5 Replies View Related

Cisco Wireless :: Number Of MAC Address Filter On WAP4410N?

Apr 12, 2012

I have gone  through the data sheet of WAP4410N,bu have got nothing about the  scalability of MAC address filter on WAP4410N?

View 1 Replies View Related

Cisco Wireless :: WAP4410N Email Alerts - Where To Put From Address

May 27, 2011

From the WAP4410N admin pages or console you can enable e-mail alerts. You have to set the essential TO address and mail server address. Where can I put the FROM address ? From what I can see it uses the hostname value as from address. The hostname in my case is ap02. Then you could try setting a mail address in the hostname field, but thats not allowed.

[Code]....

View 3 Replies View Related

Cisco Wireless :: Catalyst 4506 / 2960 - WAP4410N Mac Address Changes?

Feb 1, 2013

I'm having a weird issue with a dozen WAP4410N we just bought : The MAC address assigned to them (i.e. the one printed on the products body) apparently changes for no reason (that I can understand anyway).
 
I noticed this because I assigned static leases to them through our isc-dhcpd, and couldnt connect to them via their supposed IP address. Looking at the log I could see that the MAC was slightly different from the printed one : A4:93:4C:B1:91:56 became A2:93:4C:B1:91:57,2C:54:2D:38:E5:AA became 2A:54:2D:38:E5:AB, etc.
 
If I reboot them either from the web interface or by doing a 'shut no shut' on the POE link, they sometimes revert to the original MAC address. Sometimes not, with yet another slight variation on the MAC address.
 
While not a real issue - I can still make their IP static and be done with it - I want to understand what is happening and why. All the WAP4410N are connected to either Catalysts 4506 or 2960, VLAN is enabled, Default VLAN ID is not default, VLAN Tag is set to 'Untagged' and VLAN Tag over WDS is set to 'Disabled'. All 4410N are running '2.0.5.3' firmware.

View 2 Replies View Related

Cisco Wireless :: WAP4410N / Cannot Access Configuration Utility Or Ping Default IP Address

Sep 29, 2010

We have 3 WAP4410N on our network. Our laptops pick them up but I cannot access the configuration Utility or ping the default IP address. If their IP addresses have been changed how do I find out what their current IP adds are? We currently use static IP addressing for our network.

View 2 Replies View Related

Using MAC Address Filtering?

Dec 19, 2011

I just upgraded to the Belkin N750 DB router from the version just below it and couldn't get the wireless card (Ralink RT2760) in my daughter's dual-boot WinXP/Ubuntu 10.04 to connect to the WPA security setting (WEP only) on the Ubuntu side. There is an updated driver, but it's way above my Linux skill set, so instead I just disabled security completely, and used the MAC Address filtering to add all of our household devices.This solved her connection problem, but I am wondering if there is any danger to this method that I might not have considered

Originally Posted by BelkinMAC Address FilteringThe MAC Address Filter is a powerful security feature that allows you to specify which computers are allowed on the network. Any computer attempting to access the network that is not specified in the filter list will be denied access. When you enable this feature, you must enter the MAC address of each client on your network to allow network access to each. To enable this feature, select "Enable MAC Address Filtering". Next, enter the MAC address of each computer on your network by clicking "Add" and entering the MAC address in the space provided. Click "Apply Changes" to save the settings. To delete a MAC address from the list, simply click "Delete" next to the MAC address you wish to delete. Click "Apply Changes" to save the settings.

View 8 Replies View Related

Cisco Firewall :: MAC Address Filtering In ASA 5520?

Jul 25, 2008

CAn we filter MAC address in LAN using ASA 5520 , whats the method ?

View 2 Replies View Related

Cisco Firewall :: Does ASA 8.3 Support MAC Address Filtering

Nov 4, 2012

Does ASA 8.3 support MAC address filtering, I want to allow a single specific laptop to login to the ASA 8.3 firewall (for management) from anywhere on the internet, I know I can do it through VPN but I want a simple MAC address access list or something......

View 3 Replies View Related

Cisco :: 4402 - Mac-Address Filtering Using More Than One SSID

Apr 9, 2013

I've been asked to configure mac-address filtering on our WLC 4402 and it was basically straight forward.  however i noticed that in creating the filter you can only choose 1 SSID or the other option would be to choose all?  My question then is what happens if i need a user one 2 specific SSIDs?  can i create separate filters for each SSID but using the same mac?

View 1 Replies View Related

How Does MAC Address Filtering Secure A Network

Mar 8, 2011

How does MAC address filtering secure a network?

View 9 Replies View Related

Cisco :: WLC 5508 And 4402 - Mac Address Filtering Database

Mar 27, 2012

l have implemented mac filtering auth on my wireless network, l have 2 WLC ( 1 WLC 5508 and 1 WLC 4402, and I wonder if you can migrate the mac address database of a WLC to another and how can l do this.

View 4 Replies View Related

D-Link DIR-655 :: Network Filtering / 24 MAC Address Limit?

Jan 23, 2013

I have had a great experience with my old DIR-655 (rev A) router.  However, I would like to upgrade to a newer and better D-link router for my home that contains many well-connected children. Which routers are like my DIR-655, and have better overall performance than the DIR-655 without necessarily using the benefit of the 5 GHz second band.   What better performing routers can record more than 24 MAC addresses in the Network Filtering area?  I understand many people don't agree with MAC address filtering, but I like it to keep my kids from giving out my network password to all the neighbor kids and their friends too.  So, MAC address filtering works for me.  Or, should I just get an updated version of the DIR-655?  

View 5 Replies View Related

Cisco Routers :: RV180 / RV180W - MAC Address Filtering And IP Biding

May 24, 2012

I'm interested by the router Cisco RV180 or RV180W.
 
So as to increase security, i would like to set a MAC adress access restriction for all peripherals that would be connected to the router (10 computers, 2 servers, 6 Synology NAS) : only allowed MAC adress should access to the internet and network ressources.
 
Does the Cisco RV180 or RV180W have an IP to Mac biding feature and a Mac adress restriction feature ? If yes, how many peripherals/computers can be set ?
 
For example, only 30 mac/IP adress can be allowed on my actual router and it is not enough.

View 4 Replies View Related

Cisco Switching/Routing :: 4510 Enable MAC Address Filtering

Oct 27, 2010

I am planning to enable MAC address filtering (one port on 4510 & another 3560). I want to allow only that MAC address to communicate via that port with the rest of the network and internet.
 
4510 has PC connected and 3560 had polycom connected. [code]

View 5 Replies View Related

D-Link DIR-655 :: Web Filtering Doesn't Work When Linked To MAC Address

Jan 5, 2011

My DIR-655:
Hardware Version: A4
Product Page: DIR-655

The problem is that Website Filer doesn't work if on STEP 3: SELECT MACHINE of Access Control the machine was selected by MAC address. When the machine was selected by IP everything is fine.The problem is that IP addresses are assigned dynamically, so how to make sure that the policy would be applied to the same machine? 

View 8 Replies View Related

Belkin Routers :: N150 - When Check MAC Address Filtering It Seems To Be Disabled

Dec 25, 2012

I have a Belkin N150 wireless router. I have enabled MAC Address Filtering as an added level of security. However; whenever I access the router, and if I check that page; the check mark for the option to enable the filter is always blank.

I have checked the option, clicked Apply Changes, and logged out of the router. i went back in this morning, to check the security logs. (Looking like someone is trying to jump on my network) I didn't see anything there, but when I checked MAC Address Filtering; there was no check mark indicating that the filter was turned on.

View 2 Replies View Related

Cisco Wireless :: 802.11 WAP4410N To WAP4410N Backhaul Using N Protocol?

Apr 30, 2011

I have the following equipment:
 
Cisco 871W router
2x WAP 4410N APs running 2.0.3.3

I currently have 1 AP connected to the router via copper.  The AP to AP link is over 802.11.  I have attached a diagram reflecting the current topology.
 
The AP-to-AP link will come up utilizing B/G/N mixed mode; however, the connection is basically unusable.  About 30% of the traffic is dropped, while the packets that do make it have a consistently volatile latency, anywhere from 15 to 1500 ms. I have had success using G-only and B/G mixed.  The link is stable (I have had the best results with B/G).  The problem is, I didn't buy the 2nd 4410N to run the G protocol.  I would like to connect the APs running either B/G/N (hopefully negotiating to N) or N only.  I am wondering if there is a certain configuration I can utilize (perhaps using WDS repeater or bridge versus Wireless Client/Repeater?), or a firmware upgrade set for release that can make this happen for me.

View 1 Replies View Related

Linksys Cable / DSL :: WAG320N - Disable SSID Broadcast And Enable MAC Address Filtering?

Feb 15, 2011

When disabling SSID broadcast and enabling MAC address filtering on WAG320N, my other wireless laptop get disconnected.  And when you try to connect, it doesn't connect again.

View 3 Replies View Related

Cisco WAN :: WAP4410n On A Home Network - IP Address Range?

Mar 5, 2011

I am trying to set up a WAP4410n Wireless access point and add to my home network. One problem I can't seem to get around. The IP adress range setup does not accept 1 (example 192.168.1.245) as a range setup for IP address. How do i get in communication with the unit when I can't view the setup due to the factory default set as 192.168.1.245? If it were 192.168.0.245 I could easily change my routers IP range to include it.

View 0 Replies View Related

Cisco Firewall :: ASA 5505 URL Filtering Using URL Filtering Server?

Feb 7, 2012

I have come across articles mentioning that URL  Filtering can be implemented by using ASA 5505 with URL Filtering  Servers. But Websense and other Web Filtering Servers are paid ones ?  Are there any free solutions available ? What exactly is N2H2 ? The  reason is I don 't want to increase the CPU utilization of ASA by  implementing URL filtering within the device. If I have around 30 nodes  which connects to the internet via a 2Mbps line through ASA 5505 and if I  want to block around say 10 or 15 URLs , will it increase CU  utilization beyond permissible limits ? Currently the CPU Utilization is  around 10 - 15 . Here's the infrastructure setup .

------------------------------------------------------------
Nodes -->Switches-->ASA 5505-->Internet
-------------------------------------------------------------

View 4 Replies View Related

Cisco Wireless :: WLC 7.3.0 / MAC Filtering And Web Authentication

Feb 9, 2013

There is a feature in WLC 7.3.0 like Configuring a Fallback Policy with MAC Filtering and Web Authentication .We have an option to configure mac filtering and we can create a policy  that if mac filtering failes redirect it to web authentication
 
Here i am using mac filtering is only for my mac caching process. But when i tried this its not working.
  
My mac address is not there in the WLC, so it should prompt me the web authentication page.But its not happening. As long as my mac is not there in the table, i am not able to connect to the SSID.
  
So what is this feature (Configuring a Fallback Policy with MAC Filtering and Web Authentication) meant for ?

View 4 Replies View Related

Cisco Wireless :: 4400 Mac Filtering Import

Aug 2, 2012

I was wondering if there was a way to import a large number of mac addresses into the MAC filtering of a Cisco WLC 4400. We recently purchased 150 new Mac laptops and I need to add them to the Mac filtering. I have 5 WLC's to do this to.I already have the MAC addresses and names in a spreadsheet.

View 3 Replies View Related

Wireless Is Already Secure But Cannot Find Mac Filtering?

May 4, 2012

I want to prevent another laptop and i-phone in my house from accessing the wireless internet

View 1 Replies View Related

D-Link DIR-825 :: How To Enable SPI Firewall And Wireless MAC Filtering

Jan 23, 2013

Where on my router interface I could go to enable both the SPI Firewall, and the Wireless MAC Filtering? I have the D-link DIR-815.

View 1 Replies View Related

Linksys Wireless Router :: E4200V2 - How To Do Mac Filtering

Apr 21, 2012

Just got my new E4200 v2 router. Set up mac filtering for one device and after saving the change the router was refreshing and disconnected all my devices and could not log in to the router wired or wirelessly and had to do a factory reset. Have the latest firmware. Is this a defect in the router?

View 2 Replies View Related

D-Link DIR-600 :: Doesn't Allow To Enable Wireless MAC Filtering

May 20, 2011

DIR600 doesn't allow me to enable wireless MAC filtering when I setup DIR600 as access point. (I connected DIR600 (access point) to my another room's router.)

View 1 Replies View Related

Linksys Wireless Router :: E4200 - MAC Filtering

Jan 6, 2013

Since I have this router E4200 my network undergoes changes alone. I have a MAC filtering as I had in my previous WNRL 160N and had no problems but here the overnight me are the 14 that I have enabled MAC, put another 3 that are not from where I changed the settings WiFi network, I've put in hidden, change encryption type and others and continues to happen randomly, and I added the router directly to the list of allowed MAC. I have remote management disabled in the Cisco Network Magic are not those MAC. not because it adds the MAC and I removed some that I have put the single.

View 9 Replies View Related

Cisco Wireless :: How To Use Mac Filtering With Wildcards On 4402 Wlan Controller

Aug 3, 2011

we use wlc 4402 (Software Version  7.0.98.0) and want to allow only several wlan nic vendors to connect to a wlan ssid.According to this, is it possible to configure MAC Filtering with wildcards, e.g. aa:bb:cc:* ?

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved