My DIR-655:
Hardware Version: A4
Product Page: DIR-655
The problem is that Website Filer doesn't work if on STEP 3: SELECT MACHINE of Access Control the machine was selected by MAC address. When the machine was selected by IP everything is fine.The problem is that IP addresses are assigned dynamically, so how to make sure that the policy would be applied to the same machine?
I have one outside interface with global IP address 1.1.1.1 and two inside.Both inside interfaces restrict and non_restrict have private IP addresses.I tried to filter some URLs on PIX515 IOS 7.2, only on restrict interface but my filter does not work.I can access prohibited URL from restrict interface. What's wrong in my URL filtering?
Here is my config:
PIX Version 7.2(2)
!
hostname pixfirewall
enable password 8Ry2YjIyt7RRXU24 encrypted
names
[code]....
DIR600 doesn't allow me to enable wireless MAC filtering when I setup DIR600 as access point. (I connected DIR600 (access point) to my another room's router.)
View 1 Replies View RelatedI have had a great experience with my old DIR-655 (rev A) router. However, I would like to upgrade to a newer and better D-link router for my home that contains many well-connected children. Which routers are like my DIR-655, and have better overall performance than the DIR-655 without necessarily using the benefit of the 5 GHz second band. What better performing routers can record more than 24 MAC addresses in the Network Filtering area? I understand many people don't agree with MAC address filtering, but I like it to keep my kids from giving out my network password to all the neighbor kids and their friends too. So, MAC address filtering works for me. Or, should I just get an updated version of the DIR-655?
View 5 Replies View RelatedIt shows this option "Filter wireless clients: Apply MAC Filtering to devices that connect to the network via Wi-Fi. This is the normal usage of MAC Filtering. Filter wired clients: "However I don't see that option on the actual page. How can i enable Mac address filtering only for the wireless side?
View 7 Replies View RelatedI'm trying to configure Cisco CISCO881G-K9 3G router to connect to mobile network without success. The cellular interface gets up but it doesn't receive IP address. It seems that profile isn't activated and it should've been.
I've attached running config and some other information gathered from router.
I have the following zebra.conf on my router box "A":
hostname nuclear-router
password password
enable password password
interface eth0
ip address 192.168.2.1/24
multicast
[code]...
eth0 is connected to a switch and contains the 192.168.2.0/24 range, and A is connected to my WRT54GL "B" (with IP 192.168.1.1, containing 192.168.1.0/24 range, DHCP serves IPs above .100) wirelessly. B is connected directly to my DSL modem.
The problem is that when I specify the default route using the interface name, I can't connect to the internet from A or any hosts behind it - I'm always hit with a "no route to host" error. Name lookup and pinging any local host (even in a different range) or the DSL modem works fine - it's only when going beyond the modem that things stop working. However, when I use the IP of B as the gateway, it works fine. I noticed that route output on A when the default route was specified using the interface alone had only an asterisk in the gateway column. I was under the impression that these approaches should be identical in practice, so though I got it working, I'd like to know what I'm misunderstanding (and/or misconfiguring). Why didn't the default route work when specified using just the interface?
All routers and the modem too have RIP (version 2) enabled, and of course the password isn't really the word "password".
hardware version D3, FW 4.10 and 4.11 same problem.
i tried with 4 wlan adapters: two of them support 802.11b/g, they always work find no matter which settings. the other two support 802.11b/g/n, as default "n" is enabled, so does DIR-615, both wlan adapters can be connected to DIR-615, they get their LAN-IP, but they can access neither DIR-615(no respone to ping) nor internet. but if i disable "n" mode either in the adapter or in DIR-615, everythin works fine, of course only with 54mbit max.
so what can i do to use the n mode?
The DIR-825 wireless simply doesn't work. When I called tech support, we cleared some settings and hard-powered the unit on/off and it finally turned on the wireless radio. A couple weeks later I pull out my laptop to use in the house via wireless and the wireless on the DIR-825 is OFFLINE AGAIN...fallen and it can't get UP.Is anyone having issues with keeping their wireless online? OK - powered it off for 5 minutes...now the wireless is working. I think changing configuration settings causes the thing to lock up.
View 1 Replies View RelatedRecently I bought a Windows 8 (64bits) computer, which is now part of my home network, but it has problems with Shareport. The other computers can be easily connected to a USB printer on my DIR-825 (HW B1) router, but the W8 computer refuses to completely install Shareport (both the CD version and the latest download v1.17). I also tried Shareport-Plus v4.11 (found on the DIR 835 page), which did install correctly, but was still unable to see the USB printer. What can be done? Can D-Link provide a new version of Shareport?
View 3 Replies View RelatedI can't get my brand new DCS-930L cam to connect to my network by using the WPA / WPA2 encryption. Works ok wired, with WEP or with no encryption enabled. Red led is on the front. I've tested sw version 1.02, 1.03 and the latest 1.04b03. Same result: WPA doesn't work. I have a Thomson TG789 Gateway/Router as provided by my ISP. All other units in the network works perfectly fine on WPA i.e. PC, Mac, printers, mobile phones etc etc.
View 1 Replies View RelatedI have a DSL router Pirelli PDF A1000G.I have a Linksys e3000 and I have a dap-1522.When I bought a dap-1522 I thought it could do access point in fact i saw many videos in dlinktv before choosing an access point from DIY with mike etc to youtube there are 2 videos one showing bridged mode and another ap mode!Now what happens is this I have upgraded from firmware 1.11 that came as default to 1.21 i connect it wired to my linksys e3000 when it is connected with the ethernet cable wired I can connect to the internet and navigate and open sites and my ps3 can connect to it but my range is not very good only 40%!
Now I bring it downstairs remove the ethernet cable and connect it to the power and then you can connect to it but since it isn't connected to my router which is upstairs i can't access websites neither can I play on my ps3!I don't know does only ap mode works when it is connected to the router wired because what happens is if you don't put ethernet cables in the back of the dap-1522 and just connect it to power then here doewnstairs you can connect to the dap-1522 my signal is like 87% but while I'm connected with my laptop I can't access websites and in the ps3 I can't connect!
and choose access points there are (4) listed: dap-1522, dap-1160, dap-1353 and dap-2553, I thought of buying dap-1522 because it could support abgn while 1160 only supports g and 1353 only supports n to repeat to signal here downstairs and be a good access point!
i have a DIR-615 Rev C1, firmware 3.13.
After a reboot my password doesn't work anymore (wich is normal I guess) and all default passwords dont either. Such as ''Password'' or ''Admin''.
Edit I've found a work-around. It's on page 2: [URL]
I'm having this really weird issue with my DIR-655 revB. I have some port forwarding rules set up and externally they work fine. However, if I try connecting to my IP address using those same ports from a computer within my LAN, it won't connect.
Externally, I can ping my WAN address and connect through forwarded ports. No problems. Internally, pinging my WAN address apparently works (just now is the first time that's worked for me), however I can't access any of my computers using the WAN IP and port forwarded ports. I can access them by going directly to their hostnames or LAN IPs.
Things I've tried:
-Disabling/enabling firewalls on all computers involved
-Disabling/enabling QoS engine
-Disabling/enabling DNS relay
-Disabling/enabling Advanced DNS
-Adding custom nameservers from Google and Comodo
-Restarting computers
-Clearing DNS cache (I use a dynamic DNS name which works externally but not internally. This gets the correct IP internally and connecting directly to the IP doesn't work either.)
-Modifying the NAT Endpoint Filtering settings
I have an external DSL modem connected to the router using PPPoE if it matters.
The weird part is that it works externally but I've modified all of the values I can think of in the config with no luck. I upgraded to the DIR-655 from a DIR-615 which had all these settings in it and worked fine (until it started acting up which is why I replaced it).
I'm just wondering why my computer is being associated twice before being secured and linked when it obtains an IP address from the DIR 655 router. I am using the DWA-552 wireless card to connect to it. When I first started using them together, this wasn't happening. Then, all of a sudden, one day it just started showing "above message repeated 1 times" just below the log entry for the client being associated".
View 5 Replies View RelatedLike others I see on this board, we've got middle- and high-school age kids whose access to FB and other sites needs to be controlled/scheduled.
I thought the DIR-655 was great, in that it has features that, on the face of it, would seem to be ideal for blocking domains and restricting access.
My problem: I've never been able to get this to work.
I've set up schedules and created lists of domains that I want to limit access to according to the schedules, but the only constraint I've ever gotten to stick is blocking access completely to the router.
*None* of the schedule-based or website-based access controls have ever worked; I'll put the block in place to my daughter's computer's MAC address so she shouldn't be able to get to youtube or facebook, save, bounce the router, but then I go by her room and she's still busily chatting away online to her FB friends.
Based on similar posts I've seen on this forum, this may not be a unique problem.
So in a nutshell, this is what I want to do:
1) Block certain computers (identifiable by MAC address)
2) from being able to get to particular named domains (and any of their sub-domains)
3) according to a schedule that I can create and modify.
My preference would be to do this in the router, but again, responses I've seen here suggest that may not be possible.
I just got my DIR 825. It had 2.02NA Firmware in it. It had a few options that I wanted to use but didn't work. So I thought I would update firmware. I follow the instruction from dlink to install firmware. So I loaded 2.03 and noticed internet connection not working. So then I loaded 2.05 part1 and part2. Still could get internet connection to work but the reason to upgrade the option I wanted worked. So then I loaded 2.06 and still same result. No internet connection. So then I loaded the original firmware back in and internet connection works. Why doesn't the internet work on the other firmware updates. I got the updates from dlink website. I would like to update firmware
View 9 Replies View RelatedI had the website filter ON and it was working very well to block a few websites on a schedule. And after a few month, it doesn't work any more. While it is possible that I scewed up the setting , I have tried so many settings.
So:DIR655 fw 1.32NA,hw A3,"Enable access control" is on with the desktop MAC address (used copy this MAC)(I have also tried my laptop MAC),web site filter is set to "deny",the router time is set using NTP dlink server,
First off, my router is a D-Link DIR-655, firmware v2.07. I'm trying to port forward port 25565.
My port forward settings are this:
However, when I use this open port checker, it claims that I don't have that port open. It looks like this, without the blurred out parts:
Added note: The way I want to use it is by my IP (xxx.xxx.xxx.154:25565). I have the software installed to do so (I'm using a minecraft server, connecting through minecraft), but I can't enter my IP in the IP address field, it says that it's out of the range of the LAN.
I tried to upgrade to 2.05NA several times and there always ends up being an issue that support is too sad to give the correct answer to and just puts a consumer thru "jumping thru hoops" and getting nowhere.2.05NA (actually started with 2.03NA) first caused a problem with limiting my upload speed to 1024mb. I happened across the fix on another forum and tried it and it worked. It was the default QoS setting D-Link changed after version 2.02NA and refuses to release a new firmware to fix this for everyone. Why they don't release a new FW that fixes the issue but keeps things promised on the package working is beyond me. Now, I purchased a D-Link DNS-323 and I finally got drives to fill it some time back. If 2.05NA is loaded, the Easy Search Utility will not connect to the NAS. I have tried the version the NAS came with AND the latest version offered. It will see the NAS upon 1st launch of the latest Easy Search Utility, but it will not connect and then it disappears if you relaunch the utility and won't return until a reboot. Bottom Line: it will not connect with 2.05NA loaded. It works fine with 2.02NA.
What is the setting that D-Link has screwed over here also that is causing this problem? It is pretty sad that their own hardware items won't play well together unless you run old FW. What setting D-Link changed that is making the D-Link DIR-825 not connect to the D-Link DNS-323 NAS when the DIR-825 has 2.05NA loaded. I have a DIR-825 Rev. B1 and a DNS-323 NAS with its latest firmware. I am using 2.02NA on the router since that is the only one that works and is the latest stable release(other than the DHCP reserve issue), no matter what D-Link wants to try to make people think. I won't try their support since they NEVER did give me the fix for the QoS upload issue and when I asked them to put it as a sticky in this forum when I found the answer somewhere else....well, there is no sticky as we all know. I would like to be able to have the DHCP Reserve issue working too, but I would like to connect to my NAS more at this point.
I have several ports opened on my DIR-655 A3, pointing to specific ports on a NAS server i have on my network.
I've already try this:
- Reboot the router
- Erase all Virtual Server Settings and try open only one port
- Re-flash the router with latest European firmware - 1.34b05EU
Region : Austria
Model : TL-MR3420
Hardware Version : V2
Firmware Version : TL-MR3420_V2_121206
ISP : 3
I am using a MR3420 V2 together with a E398 modem. The connection works well, but I can't do any port forwarding (virtual server). Using another router (Tiny Dovado) with the same E398 modem works flawlessly to forward ports.
Region : Germany
Model : TL-MR3040
Hardware Version : V1
Firmware Version :
ISP :
Just got TL-MR3040 from amazon, not very happy that it is version 1, they could at least mention it in the description, but whatever...The problem is, i can not make it work with my PC laptop(thinkpad x120e with Windows 7 64 bit). Which means,1 not possible to get into web interface to configure it, and 2 if i configure it with old powerbook (os x 10.4) to share internet from usb stick, i can connect to it's wireless network but it doesn't share internet with my pc laptop,while mac and ipad working perfect...I've try to log in into web interface through the cable, still no luck...Not sure i want to re-install the whole system on my laptop just to see if it will change anything, it works with any other router, and usb sticks...
I have (2) 942-L, and (1) 5222-L on one network. port forwarding set on router; (942) 192.168.1.3:1024, (942) 192.168.1.4:1025, and (5222) 192.168.1.8:80. no matter if all 3 are connected to dViewCam, only two will work at a time. Disconnect any third, and they work fine. reconnect 3rd, and one disconnects intermittently. On a side note, if I run a different program on another computer (iMac); i.e. IP Camera Viewer, they all work fine. I know, I know, but I like DViewCam, because it's the only thing running the PC computer.
View 3 Replies View RelatedI recently set up two cameras. I had set up one for motion detection and email to a gmail account. It seemed to work fine, but then for some reason the motion detection tab didn't show the room like it did before. It doesn't show any picture or anything like it did before, so I couldn't choose the squares to choose the detection area. This is through mydlink account->camera info->advanced settings, and logging in to the camera remotely.So I switched to the other camera, and got it working as of last week. But now, the motion detection doesn't work anymore? It appears to be related to the username/password for the email account. I can no longer send test emails, it says invalid username/password, though the exact same values worked last week, and I didn't change anything. I tried resetting it, then setting it again, but no luck.
View 5 Replies View RelatedRegion : India
Model : TL-MR3420
Hardware Version : V1
Firmware Version : 3.12.21 Build 120523 Rel.37880n
ISP : Reliance
I've just set up a MR3420. It works fine in "WAN only" mode and provides access via our ADSL modem. It also works fine in "3G only" mode and provides access via a Reliance Netconnect+ USB modem (a Huawei E150 I think). I updated the firmware to the latest version in order to get it to work with the USB modem.
The problem I have is that when I set it to "3G preferred" it doesn't seem to connect over 3G. I can see it tries to connect but then fails and then WAN takes over. The connect and disconnect options are greyed out on the 3G page so I am unable to manually get it to retry. I've tried leaving it for a long time but it doesn't seem to connect over 3G ever. I've tried setting 3G to connect on demand and connect automatically but both behave the same.
I know there are a lot of threads out there regarding connection issues, both with wireless & LAN connections, after updating firmware to 1.35. To provide a snapshot of my setup...I have 3 GB switches throughout my home, a couple Ethernet enabled Blu-Ray players, 2 XBOX 360's, multiple satellite receivers with Ethernet, 5 PC's, 3 iphones, etc...you get the picture. I also have 5 older DLink wi-fi cameras. So, with this said my setup has been flawless for some time. However, a week or so ago I upgraded my firmware on my DIR-655 to the latest version...everything still seemed fine at the time. Yesterday I noticed we had no wireless internet so I went and checked. Sure enough...no connectivity on my desktop that's directly linked to the router, etc.
I tried rebooting & then resetting the router...got connectivity, but as soon as I plugged my PC into the switch...no IP address. I played around with settings, wiring configurations, etc...I'm pretty up to speed on this setup so I felt I exhausted every option. I thought my router went bad...gave me an excuse to go get the latest so I brought home a NetGear N750...hooked it up. As soon as I changed the LAN IP address range to condense the #of IP addresses I'm giving out again, the LAN connection to the PC was lost...I could not get it restored. I finally got it working, bypassing the GB switch, but the wireless would lose connection literally after a few seconds.
I ended up taking the NetGear router back and bought the exact same DIR-655, but this time it was HW version B1 instead of A and it was firmware #2.00 or something like that. I hooked it up when I got home...configured the system to exactly the way I had it before and PRESTO!!! My system is working like it was before. I can only think that the firmware upgrade I made on the previous router screwed something up in my system.
For some reason I can't get Access Control/Webaccess Filters working on my Dir-655 w/ 1.35NA. I've tried it with MAC and IP Address without any success. I've also enabled/disabled/enabled DNS Relay, recreated the rules, recreated the filters, etc. Nothing.
View 14 Replies View RelatedI have a fixed external ip address.I have port forwarding setup for accessing a NAS inside my LAN, lets say port 12345.Now when I use my laptop outside my own LAN, e.g. 99.99.99.99:12345 resolves nicely to my NAS. But when I use the same 99.99.99.99:12345 inside my LAN, it does not resolve. Instead, it gives me a 'server takes too long to answer' error
I have also setup a virtual host to an ip cam inside my network. That one resolves just fine. I tried enabling remote management on the DIR-655 and also that works fine using 99.99.99.99:8888.When I replace the external ip address with the internal ip address of my NAS, thus bypassing port forwarding, it obviously also works ok.
Why the forwarded ports are not accessible when I use my own external fixed IP address? Does the DIR-655 treat it different than other external IP addresses?
I have multiple computers on my network as well as cell phones logging in as wifi. At least once a day I have trouble or another computer has trouble getting on line through my network. I have to unplug my router and replug. Its as if it doesn't recognize the ip address until reboot.
View 1 Replies View RelatedRegion : Netherlands
Model : TL-WR1043ND
Hardware Version : Not Clear
Firmware Version :
I installed my brand new TP-Link router and both wired and wireless internet connection work perfectly fine. But when I tried to secure the wifi with a password (I followed the instructions on last page of installation guide) I can not connect to the internet any more. After entering the correct password, both iphone and mac-book simply say "unable to join the network". I selected WPA2-PSK-personal as recommended. For now I switched off the security settings, but I live in a building with many neighbours and they are now consuming most of my bandwidth (apparentlyI am surrounded by illegal downloaders
Region : Brazil
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 Build 120810 Rel.44064n
First of all, by connecting the router to my desktop through wire, it doesn't generate any IP address, except for 169.254.x.x.. I already tried configuring the IP to static mode, but nothing changed, I can't even access the router's interface, however, if I try the same thing (connecting the router through wire) with my notebook and netbook, I get the IP without any problems.
The second problem is related to the wireless connection. When I try to connect my smartphone (Motorola XT860) I get the IP normally and supposedly internet connection, however the connection only lasts for a few seconds, after that I am incapable of accessing even the router's interface (again). If my smartphone stays connected to the router, nothing else works even for other connected devices, but when I disconnect my smartphone, all the other connections resume as if nothing happened. I already tried changing the Beacon Interval, the Address Lease Time, and so on, but nothing has worked.
I have a big problem with my cisco wrv210. I want to use URL Filtering to block facebook.
Enable
ip range : 192.168.2.5-192.168.2.254
url string : Facebook, www.facebook.com , facebook.com notting work.
