D-Link DIR-825 :: Doesn't Recognize IP Address Until Reboot
Jan 22, 2013
I have multiple computers on my network as well as cell phones logging in as wifi. At least once a day I have trouble or another computer has trouble getting on line through my network. I have to unplug my router and replug. Its as if it doesn't recognize the ip address until reboot.
I reset my WAP54g v3.05 to factory default to allow an older computer access to my network.
Now I've reinstalled it for better security using my newer laptop: no SSID broadcast and encryption set for WPA2-personal. However, when I enable Mac filtering and permit my newer laptop, the WAP54g does not recognize it.
Disable Mac filtering and my laptop is back on the network.
DGL-4100 -> Wii -> X360 -> PS3 -> DGS-2205 (gigabit switch in study) *-> My PC *-> Her PC *-> DAP-1522
We're on the 192.168.1.x domain, and I've already hooked my PC up directly to the DAP-1522 and switched its IP address. So now, I can connect to it through the switch. I've renamed it, set it to WPA2 with a passphrase, and should be set to go. However, I can't get my laptop, IPod touch, or any devices to see it. Also, the DGL-4100 doesn't list it under the DHCP clients, but as I've got the DAP-1522 set to a static IP of 192.168.1.50.
Region : Argentina Model : TL-WR1043ND Hardware Version : V1 Firmware Version : ISP :
I've been using this router for almost 2 years and it has been excellent but since 2 weeks ago it has stopped recognizing anything connected to the LAN port 1 and the WAN port, so it becomes useless as a router because I cannot connect a cable modem. The cable modem was tested successfully with a direct connection to a computer but it doesn't work with the router, and also ANYTHING you connect to these ports on the router is not detected, the lights do not turn on.
Region : Others Model : TL-MR3040 Firmware Version: 3.14.4 Build 121017 Rel.62268n
I have purchased TL-MR3040 especial for share my 3G account . I have connect it by ethernet port and made setups and it is in 3g/4g only mode. In system checks my modem indicated as " Identified" the modem is a Huawei E160E . My notebook and tablet connects by wireless connection to TL-MR3040 but the router does not dial ISP number *99# . The led on usb modem continues flashing. the 3G modem works perfectly with my notebook and tablet and I use the same parameters for TL-MR3040 with tablet. But most of the parameters don't exist on setup pages of TL-MR3040 . [code]
I have a fixed external ip address.I have port forwarding setup for accessing a NAS inside my LAN, lets say port 12345.Now when I use my laptop outside my own LAN, e.g. 99.99.99.99:12345 resolves nicely to my NAS. But when I use the same 99.99.99.99:12345 inside my LAN, it does not resolve. Instead, it gives me a 'server takes too long to answer' error
I have also setup a virtual host to an ip cam inside my network. That one resolves just fine. I tried enabling remote management on the DIR-655 and also that works fine using 99.99.99.99:8888.When I replace the external ip address with the internal ip address of my NAS, thus bypassing port forwarding, it obviously also works ok.
Why the forwarded ports are not accessible when I use my own external fixed IP address? Does the DIR-655 treat it different than other external IP addresses?
My DIR-655: Hardware Version: A4 Product Page: DIR-655
The problem is that Website Filer doesn't work if on STEP 3: SELECT MACHINE of Access Control the machine was selected by MAC address. When the machine was selected by IP everything is fine.The problem is that IP addresses are assigned dynamically, so how to make sure that the policy would be applied to the same machine?
I have an IBM R-40 thinkpad that I restored to original with the IBM icon and then updated it to a service pack 3 and updated anything that popped up. Now it doesn't recognize any wireless at all. I tried the FN,F5 still no luck. It has a INTEL card, Model WM3B2100 in it and it worked fine before the restore and update.
I recently had to reinstall XP and all the drivers for my friend's laptop but it seems it does not recognize any wireless connections. When I click the Choose a wireless network it says "No wireless networks were found in range" however I can use my laptop just fine.I clicked the network adapter and it says everything is running fine so I am not sure what the issue is. How to get the wireless internet working.
I am trying to an Epson WF 545 to connect to a wireless network. I get an error message when it fails to connect to a networked iMac. The message says, "Entered security key/password does not match the one set for your router/access point."Several weeks ago, I had to reset my wireless network password/security key. That reset worked for our 3 PCs and 2 Macs including this iMac...the one that now doesn't connect to the wireless printer or maybe vice versa...why the iMac can't connect to the Epson (or vice versa), but the iMac does connect to the wireless network, and in order to do that, it makes use of the new network password / security key that I just put in the Epson to set it up in the network. Can you tell me if the wireless router somehow has a password / security key that I did not change when I changed the wireless network security key? The new network password/security key that I entered in the Epson is correct.
when I click on an icon like yahoo or facebook or any other icons my compuyrt says doesnt recognize,typed in add wrong, cant figute it out. Its on dsl an my laptops work fine from my wireless.
My gateway net book has always recognized wifi, but since we left home a few weeks ago I have not been able to connect. My computer savvy nephew couldn't even figure it out.
I'm using an nvidia ethernet card that's in my mobo. Yesterday I had internet without any problems but this morning when I turned my computer on, the light on it wasn't blinking. Tried turning power on/off, unplugging and pluhging back but still no solution.Checked Device Manager and there is no (!) or (?) next to the device name. Also it says device is working properly. Even did the "scan for hardware changes" and again it shows that device is working properly.. But that's not all! The weirdest thing here is that my 3 neighbours who are from the same ISP have the exact same problem. We're connectrd to 1 box that is outside. The other part of the village that is on the same ISP has no such problems. So I'm wondering if it's a local corrupt cable problem or our cards have fried. I believe we use fiber optic cables.
I'm using sapo internet USB pay as you go internet,the only problem I cannot get my windows vista to get connected . the software downloaded perfectly it just cannot connect to network! the computer i'm using now is gonna disappear soon!
My computer does not see the internet. If I do a restore to an earlier restore point, it can see the internet,, but when I do a restart it goes back to not allowing me to access it. The weather gadget cannot see the internet either. The OS is Win7 64.
Region : Brazil Model : TL-WDR4300 Hardware Version : V1 Firmware Version : 3.13.23 Build 120810 Rel.44064n
First of all, by connecting the router to my desktop through wire, it doesn't generate any IP address, except for 169.254.x.x.. I already tried configuring the IP to static mode, but nothing changed, I can't even access the router's interface, however, if I try the same thing (connecting the router through wire) with my notebook and netbook, I get the IP without any problems.
The second problem is related to the wireless connection. When I try to connect my smartphone (Motorola XT860) I get the IP normally and supposedly internet connection, however the connection only lasts for a few seconds, after that I am incapable of accessing even the router's interface (again). If my smartphone stays connected to the router, nothing else works even for other connected devices, but when I disconnect my smartphone, all the other connections resume as if nothing happened. I already tried changing the Beacon Interval, the Address Lease Time, and so on, but nothing has worked.
My computer suddenly doesnt recognize my router.it recognizes othrer routers, and my other PC's are recognizing the router.the router is located very close to the PC, and no other electronic devices located near by.
My Dell destop with Windows 7 all of a sudden doesn't seem to recognize my router, yet my laptop works fine (which I'm using now). After reading other posts, I reset the router with no results, used a new cable from the Belkin to the computer, changed ports, checked connections, restarted; nothing. When I do an ipconfig, a small window pops open and goes off before I can make anything out. I undestand Belkin's IP address is 192.168.2.1 and I'm showing that my IPv4DHCP Server is that, as is my DNS server. The IPv4WINS server shows nothing.
I just moved into a new apartment and inherited a former roommates internet set up. Our router was infected with DNSchanger, so I sought to reset the router and update the firmware. I reset the router and it no longer recognized the internet connection. I can connect when plugged directly into the modem, but the router doesn't recognize the internet connection. Below is my ipconfig/all log:
Microsoft Windows [Version 6.1.7601] Copyright (c) 2009 Microsoft Corporation. All rights reserved. C:UsersREDACTED>ipconfig/all
I usually connect my PS3 to a switch which then goes to the BuT Home Hub and it works fine. However, I want to connect the PS3 directly to my Hub but when I plug it in to the Hub, it doesn't connect to the internet at all. Is there something I have to configure in order to get it to work?It is a PS3 160 GB Slim with Firmware 4.0.
just got a new supervisor 4 engine for this catalyst 4503 switch that has ios 12.2 (53) SG installed on it. That's quite a bit above the 7.6 i was working with. I'm having a couple issues now. first, I read that it is supposed to be sending out broadcasts automatically to get it's IP address but it doesn't seem to be. the module i'm plugging into there is ws-x4448-gb-rj45, a 48 port 10/100/1000 module in case it matters. it works other than that. I can plug two computers in and see them and i can plug the network in and they'll both get addresses and internet, but i need an IP on the switch. is there a way to send a manual request for broadcast out or somehow set the IP manually? (I know I can do it in the rommon, but that doesn't seem to do anything)
also, the last module in the switch is a 24 port poe ws-x4224-rj45v. the module is recognized, the status light green, the "show interface status" lists it, but it doesn't recognize anything plugged into it. the supervisor is not configured at all yet, so maybe that has something to do with it, but the other module, like i said, works.
I just installed two of the HWIC-1GE-SFP cards in the CISCO3945 router but they are not recognized... I don't see any messages on the console output. I don't see them in the "show diag" command. I don't see new ports in the "show run" either... Is there some command I need to put in to activate them? Here is show version of my router:
I have a laptop that I want to sell, therefore I went to somebody to see my laptop and wanted to connect to his wifi. After repeatedly entering the pass for the wifi ,the wifi was still not connecting.
1. My laptop will see his wifi but after entering the pass will not connect 2. The pass is correct because I introduced the same pass on my mobile and I was able to connect to his wifi through my mobile 3 My laptop wifi is working fine because when I went home it connects automatically on my home wifi 4. I tried to open and close his router but I faced same problem.
Ok this is the send router this has happened to but anyway after a power blink the router no longer recognizes that i have a modem connected to it no matter how many times I reboot both of them it can't recognize that i have a modem connected i know it is not the modem because i'm using it to type this right now directly connected to my desktop
I have windows 7 Linkysy E4200 V1 Century link DSL modem 660 series
I cannot use my AE1000 device for more than twenty minutes connected on windows ultimate 64bit.AE1000 doesn't startup with Windows 7 64bit.The led light still turn on when I turned off my PC.
Recently got satellite high speed. Am trying to hook up the wireless router my son gave me. Installed and set up but my PC doesn't recognize it and my phone won't pick it up.
I have a Dell desktop with Windows 7, a Dell laptop with Windows XP & a Toshiba Satellite laptop with Windows 7. I bought a new router for faster internet speed - Netgear N600. I now have internet on the two laptops, the Kindle Fire HD & my Iphone. I cannot access the internet on the desktop. It shows that I am connected to an unidentified network but I can't get online. The techs I talked to said it's a problem with my computer but I didn't have that problem before.
I've recently upgraded to windows 8 and I've been having some issues with my wireless connectivity. I've narrowed it down to an issue with the wireless adapter. Specifically, windows doesn't seem to recognize my Intel centrino Advanced-N + WiMAX 6250 and instead installed drivers for Intel Centrino Advanced-N 6250 AGN. The correct driver is instead listed in "Other Devices" in the device manager.
I have a WRT54GS V7 that I have been running for a few years now with no problems until today.My wife used the internet from her laptop through the day but this evening after she moved to the bedroom and booted up the laptop, she found there was no internet connection. I tried what I know in cases like these, unplugging the router or modem for brief periods of time to try and get things going again but to no avail. So I tried using the Easylink Advisor which basically suggested the same process.
At this point, my internet connection is coming in from the cable just fine. I have access on the desktop which is wired and works with no problems. The modem and router lights are both signaling that everything is fine but no wireless internet coming from the router.
Using the desktop I tried looking for some solutions and tried resetting the router. I ultimately called customer support but being out of warranty they wanted too much although she suggested that I needed to reconfigure the router since I had reset it. I followed the online instructions for reconfiguring but still have gotten nowhere.