Recently got satellite high speed. Am trying to hook up the wireless router my son gave me. Installed and set up but my PC doesn't recognize it and my phone won't pick it up.
View 2 RepliesI have a WRT54GS V7 that I have been running for a few years now with no problems until today.My wife used the internet from her laptop through the day but this evening after she moved to the bedroom and booted up the laptop, she found there was no internet connection. I tried what I know in cases like these, unplugging the router or modem for brief periods of time to try and get things going again but to no avail. So I tried using the Easylink Advisor which basically suggested the same process.
At this point, my internet connection is coming in from the cable just fine. I have access on the desktop which is wired and works with no problems. The modem and router lights are both signaling that everything is fine but no wireless internet coming from the router.
Using the desktop I tried looking for some solutions and tried resetting the router. I ultimately called customer support but being out of warranty they wanted too much although she suggested that I needed to reconfigure the router since I had reset it. I followed the online instructions for reconfiguring but still have gotten nowhere.
Just made a fresh computer, installed Win98 (have only 128 ram so no XP) I have a card I put in the computer from Linksys which allows for a desktop to have wireless internet. I installed the Linksys software. (first thing I've ever installed on this Computer after Windows) It doesn't pick up the wireless signal in the house (my laptop does just fine).. is there another program floating around somewhere?
View 2 Replies View RelatedI have a CME that has a FXO card, I can call the CME's number from an on-site phone and it works just fine, but when I try from my cell phone it picks up but doesn't give the dial-tone like it's suppose to, but if I hook an analog line to the phone line I can call that no problem from my cell?
voice-port 0/0/0
supervisory disconnect dualtone mid-call
secondary dialtone
timeouts call-disconnect 2
timeouts ringing 30
timeouts wait-release 2
timing hookflash-out 500
caller-id enable
dial-peer voice 201 pots destination-pattern 9T port 0/0/0 and I can see it pick up.
I was under the impression that an FXO card didn't have any clue about inside/outside etc, all it knew was that it was getting a signal to ring.
I bought the Telkom wi-fi router with A 3G dongle. If I plug the 3G dongle directly into a laptop it picks up immediately but when I plug it into the router it doesn't pick it up at all.
View 2 Replies View RelatedI have an IBM R-40 thinkpad that I restored to original with the IBM icon and then updated it to a service pack 3 and updated anything that popped up. Now it doesn't recognize any wireless at all. I tried the FN,F5 still no luck. It has a INTEL card, Model WM3B2100 in it and it worked fine before the restore and update.
View 1 Replies View RelatedI connected my router to a new computer. The computer is connected to the Internet.My SmartPhone won't connect via the router.
I logged in to the router from my cell and entered the password.The cell says the following over and over without connecting: ScanningObtaining IP address from routerDisconnectedConnectingScanning ... over & overHow can I connect my Samsung GAlaxy SII Skyrocket to my WiFi router [WRT54GS]?
I recently had to reinstall XP and all the drivers for my friend's laptop but it seems it does not recognize any wireless connections. When I click the Choose a wireless network it says "No wireless networks were found in range" however I can use my laptop just fine.I clicked the network adapter and it says everything is running fine so I am not sure what the issue is. How to get the wireless internet working.
View 2 Replies View RelatedI just set up my wireless security, and I get "incorrect password" message when I try to log onto my ipad.
View 1 Replies View RelatedI have a laptop that I want to sell, therefore I went to somebody to see my laptop and wanted to connect to his wifi. After repeatedly entering the pass for the wifi ,the wifi was still not connecting.
1. My laptop will see his wifi but after entering the pass will not connect
2. The pass is correct because I introduced the same pass on my mobile and I was able to connect to his wifi through my mobile
3 My laptop wifi is working fine because when I went home it connects automatically on my home wifi
4. I tried to open and close his router but I faced same problem.
Region : Argentina
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version :
ISP :
I've been using this router for almost 2 years and it has been excellent but since 2 weeks ago it has stopped recognizing anything connected to the LAN port 1 and the WAN port, so it becomes useless as a router because I cannot connect a cable modem. The cable modem was tested successfully with a direct connection to a computer but it doesn't work with the router, and also ANYTHING you connect to these ports on the router is not detected, the lights do not turn on.
Ok this is the send router this has happened to but anyway after a power blink the router no longer recognizes that i have a modem connected to it no matter how many times I reboot both of them it can't recognize that i have a modem connected i know it is not the modem because i'm using it to type this right now directly connected to my desktop
I have windows 7
Linkysy E4200 V1
Century link DSL modem 660 series
I cannot use my AE1000 device for more than twenty minutes connected on windows ultimate 64bit.AE1000 doesn't startup with Windows 7 64bit.The led light still turn on when I turned off my PC.
View 3 Replies View RelatedI've recently upgraded to windows 8 and I've been having some issues with my wireless connectivity. I've narrowed it down to an issue with the wireless adapter. Specifically, windows doesn't seem to recognize my Intel centrino Advanced-N + WiMAX 6250 and instead installed drivers for Intel Centrino Advanced-N 6250 AGN. The correct driver is instead listed in "Other Devices" in the device manager.
[URL]
I have configured a cisco UC520 with inbound called coming in on FXO port 0 and have configured it as a co-line. I have 4 phones set up on the system including the wireless 7921 phone, the problem is that if i answer the call on the 7921 it does not give me the option to hold or transfer the call however the other phones do (7931).
View 1 Replies View RelatedI am trying to an Epson WF 545 to connect to a wireless network. I get an error message when it fails to connect to a networked iMac. The message says, "Entered security key/password does not match the one set for your router/access point."Several weeks ago, I had to reset my wireless network password/security key. That reset worked for our 3 PCs and 2 Macs including this iMac...the one that now doesn't connect to the wireless printer or maybe vice versa...why the iMac can't connect to the Epson (or vice versa), but the iMac does connect to the wireless network, and in order to do that, it makes use of the new network password / security key that I just put in the Epson to set it up in the network. Can you tell me if the wireless router somehow has a password / security key that I did not change when I changed the wireless network security key? The new network password/security key that I entered in the Epson is correct.
View 9 Replies View Relatedwhen I click on an icon like yahoo or facebook or any other icons my compuyrt says doesnt recognize,typed in add wrong, cant figute it out. Its on dsl an my laptops work fine from my wireless.
View 2 Replies View RelatedMy gateway net book has always recognized wifi, but since we left home a few weeks ago I have not been able to connect. My computer savvy nephew couldn't even figure it out.
View 1 Replies View RelatedI'm using an nvidia ethernet card that's in my mobo. Yesterday I had internet without any problems but this morning when I turned my computer on, the light on it wasn't blinking. Tried turning power on/off, unplugging and pluhging back but still no solution.Checked Device Manager and there is no (!) or (?) next to the device name. Also it says device is working properly. Even did the "scan for hardware changes" and again it shows that device is working properly.. But that's not all! The weirdest thing here is that my 3 neighbours who are from the same ISP have the exact same problem. We're connectrd to 1 box that is outside. The other part of the village that is on the same ISP has no such problems. So I'm wondering if it's a local corrupt cable problem or our cards have fried. I believe we use fiber optic cables.
View 3 Replies View RelatedI'm using sapo internet USB pay as you go internet,the only problem I cannot get my windows vista to get connected . the software downloaded perfectly it just cannot connect to network! the computer i'm using now is gonna disappear soon!
View 1 Replies View RelatedMy computer does not see the internet. If I do a restore to an earlier restore point, it can see the internet,, but when I do a restart it goes back to not allowing me to access it. The weather gadget cannot see the internet either. The OS is Win7 64.
View 1 Replies View Relatedjust got a new supervisor 4 engine for this catalyst 4503 switch that has ios 12.2 (53) SG installed on it. That's quite a bit above the 7.6 i was working with. I'm having a couple issues now. first, I read that it is supposed to be sending out broadcasts automatically to get it's IP address but it doesn't seem to be. the module i'm plugging into there is ws-x4448-gb-rj45, a 48 port 10/100/1000 module in case it matters. it works other than that. I can plug two computers in and see them and i can plug the network in and they'll both get addresses and internet, but i need an IP on the switch. is there a way to send a manual request for broadcast out or somehow set the IP manually? (I know I can do it in the rommon, but that doesn't seem to do anything)
also, the last module in the switch is a 24 port poe ws-x4224-rj45v. the module is recognized, the status light green, the "show interface status" lists it, but it doesn't recognize anything plugged into it. the supervisor is not configured at all yet, so maybe that has something to do with it, but the other module, like i said, works.
I just installed two of the HWIC-1GE-SFP cards in the CISCO3945 router but they are not recognized... I don't see any messages on the console output. I don't see them in the "show diag" command. I don't see new ports in the "show run" either... Is there some command I need to put in to activate them? Here is show version of my router:
Cisco IOS Software, C3900 Software (C3900-UNIVERSALK9-M), Version 15.0(1)M4, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
[Code]....
My computer suddenly doesnt recognize my router.it recognizes othrer routers, and my other PC's are recognizing the router.the router is located very close to the PC, and no other electronic devices located near by.
View 2 Replies View RelatedMy Dell destop with Windows 7 all of a sudden doesn't seem to recognize my router, yet my laptop works fine (which I'm using now). After reading other posts, I reset the router with no results, used a new cable from the Belkin to the computer, changed ports, checked connections, restarted; nothing. When I do an ipconfig, a small window pops open and goes off before I can make anything out. I undestand Belkin's IP address is 192.168.2.1 and I'm showing that my IPv4DHCP Server is that, as is my DNS server. The IPv4WINS server shows nothing.
View 9 Replies View RelatedI just moved into a new apartment and inherited a former roommates internet set up. Our router was infected with DNSchanger, so I sought to reset the router and update the firmware. I reset the router and it no longer recognized the internet connection. I can connect when plugged directly into the modem, but the router doesn't recognize the internet connection. Below is my ipconfig/all log:
Microsoft Windows [Version 6.1.7601]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:UsersREDACTED>ipconfig/all
[Code].....
I have multiple computers on my network as well as cell phones logging in as wifi. At least once a day I have trouble or another computer has trouble getting on line through my network. I have to unplug my router and replug. Its as if it doesn't recognize the ip address until reboot.
View 1 Replies View RelatedMy Linksys WRT120N router doesn't accept my cellphone's MAC address... Phone's MAC address is AC:81:F3:08:13:F5 but upon adding the MAC address Internet Access Priority Category based on MAC address, I get an error "Assign MAC address is incorrect".
View 1 Replies View Relatedmy 5505 running on version 8.2.5 doesn't seem to recogize the simple command "ip address dhcp setroute......"
ciscoasa(config-if)# ip address dhcp
^
ERROR: % Invalid Hostname
ciscoasa(config-if)# ip address ?
configure mode commands/options: Hostname or A.B.C.D Firewall's network interface address
I usually connect my PS3 to a switch which then goes to the BuT Home Hub and it works fine. However, I want to connect the PS3 directly to my Hub but when I plug it in to the Hub, it doesn't connect to the internet at all. Is there something I have to configure in order to get it to work?It is a PS3 160 GB Slim with Firmware 4.0.
View 2 Replies View RelatedDGL-4100
-> Wii
-> X360
-> PS3
-> DGS-2205 (gigabit switch in study)
*-> My PC
*-> Her PC
*-> DAP-1522
We're on the 192.168.1.x domain, and I've already hooked my PC up directly to the DAP-1522 and switched its IP address. So now, I can connect to it through the switch. I've renamed it, set it to WPA2 with a passphrase, and should be set to go. However, I can't get my laptop, IPod touch, or any devices to see it. Also, the DGL-4100 doesn't list it under the DHCP clients, but as I've got the DAP-1522 set to a static IP of 192.168.1.50.
Region : Others
Model : TL-MR3040
Firmware Version: 3.14.4 Build 121017 Rel.62268n
I have purchased TL-MR3040 especial for share my 3G account . I have connect it by ethernet port and made setups and it is in 3g/4g only mode. In system checks my modem indicated as " Identified" the modem is a Huawei E160E . My notebook and tablet connects by wireless connection to TL-MR3040 but the router does not dial ISP number *99# . The led on usb modem continues flashing. the 3G modem works perfectly with my notebook and tablet and I use the same parameters for TL-MR3040 with tablet. But most of the parameters don't exist on setup pages of TL-MR3040 . [code]
My computer doesn't recognize my network card, so I need to reinstall my network drivers.There are three drivers listed for my XPS 8300...service tag.
View 1 Replies View Related