Cisco Firewall :: PhishTrap Pattern Update Failed - ASA-SSM-CSC-20
Jan 29, 2013
I manage one CSC from one of my customers. All ok with this module except updates for PhishTrap pattern.I reset and restarted the module. CSC have valid licence and no warnings about Maintenance Agreement.
I tried to do this operation manualy but stil receive in Update tab the output that packet 1012 it's available but failed to update to this version.In TmuDump file log i see that this .zip file it's downloaded and CSC try to merge with current file (1011) .I attached the part with this step from log file and sh ver output from CSC.
View 3 Replies
ADVERTISEMENT
Jan 29, 2012
after last Microsoft update MS12-006 I am unable to connect from anyconnect client to router WebVPN gateway. The VPN uses certificates for client authentication. Router is Cisco2911 - running IOS version 151-4.M1.I approved by uninstalling the update the problem is definitely in MS update MS12-006 – see detail in[URL] - but uninstalling update is not good solution for users with automatic update turned on.I am not able even to connect to webportal page from IE9 (Error message: Application Internet Explorer is not able to display this web page - or someting like this - I translated it to english from my native language). The only workaround I found till this day is using Firefox to start webvpn connection (I had to import user certificate to firefox storage as it is not able to use windows certificate storage).
View 1 Replies
View Related
Nov 28, 2012
i tryed to update my rv120w from 1.0.2.6 to 1.0.4.10 after about 15 minutes i power cycled the router.it now has alternating green power and wireless lignts flashing and router is unresponsive.
it does not give out ip address and not reachable when seeting static ip on cpui have tried the reset button.Can this unit be recoverd somehow?
View 2 Replies
View Related
Sep 25, 2011
I just bought an RV220w. My first act was updating th firmware to 1.0.2.4. Unfortunately I was not able to configure the router for vlan purpose 'cause the "Port VLAN" point was missing in the webinterface. I performed several factory reset but it didnt work for me - so I got back to firmware 1.0.1.0.
View 9 Replies
View Related
May 10, 2011
Have an SRW2024 that I was updating firmware and it got interrupted. Now I can't access the switch from either console or IP. Switch will not pass traffic. Is there a way to get this switch completely reset so I reconfigure and use it again?
View 1 Replies
View Related
Jul 1, 2011
I just downloaded and tried to apply the latest Firmware update to my dcs-930l. It failed or timed out. Now the camera is unusable. I tried the hard reset, several times, holding it in for 10 seconds after 3 seconds did not work. I held it in for 3 seconds, waited 1 minute, and just got a flashing red light. I did the same thing after holding reset in for 10 seconds. I have unplugged and replugged in the network cable on both ends several times and turned the power off and on on the router and camera several times. The camera only blinks with a red flashing light. Is it a brick now? Is there any other magic tricks to try?
View 7 Replies
View Related
Jan 19, 2011
My 1 day old WAG160N doesn't seem to want to work after upgrading the firmware. Its the V2 Annex A so I made sure I had the right file, followed the instructions on the site and all went fine, router updated and rebooted. After the reboot I held the reset button for the 30 seconds as suggested, plugged in the ethernet to my laptop and popped in the CD to set it up again.Going through the setup it got to the point of detecting the router and could not find it, checked the lights on the router and the only one lit is the ethernet that the laptop was plugged into, none of the others were. I switched off the router and turned it back on, the power light and the ethernet lights all lit up, then the power light went red and a few seconds later went off. Ethernet light was still on.
View 1 Replies
View Related
Oct 31, 2012
I upgraded to ASA 9, and asdm 7, everything went perfect except AnyConnect IKEV2 doesnt work anymore, I have a lot of errors under my event viewer:
When it goes to install I get this error: Failed to perform required client update checks. Contact your system administrator
Under Eventviewer I find:
Function: CDownloadTask::Run
File: .DownloadTask.cpp
Line: 413
[Code].....
View 3 Replies
View Related
Jan 17, 2012
Had just purchased a new DCS942L unit and had it setup fine. Registered it on the web and the web stated that it needed a firmware update. Connected with hard line and started update. After 5min webapp said device timed out. When I went to rest camera could no longer get a connection of any kind.
View 1 Replies
View Related
Mar 9, 2013
We recently installed Cisco 6509-E with dual Sup 720-BXL. We are using this switch on internet Edge. Internet connection is terminating on 10GIG fiber port.We do have following line cards installed.
1. 10 GIG * 4 port line card
2. 1 GIG * 8 port line card
3. Empty
4. Empty
5. Sup 720-3BXL
6. Sup 720-3BXL
7. 1 GIG * 48 ports
8. 1 GIG * 48 ports
9. 1 GIG * 48 ports
We do have 2 GB internet pipe.We are running load test sending http port 80 request and when load reach to arround 100 to 200 mbps and connections from out side to inside 80,000 switch start reponding very very slow and start packet loss and when I try to ping from one server to second server it show normal ping but if I tried to ping gateway IP of server which is SWITCH IP it show packet loss and very high letancy.
Switch also throw message "No memory available: Update of NVRAM configuration failed"
View 7 Replies
View Related
Dec 10, 2012
From 6.0.199.4 to AIR-CT5500-K9-7-3-101-0.aes. Get the error below halfway through download of file to controller.
*Dec 11 14:18:55.775: %UPDATE-3-FTP_TRANSFER_FAIL: updcode.c:4158 Error FTP file Transfer [ftp_get], <28>, No space left on device.
I have no idea how to delete files form the storage on the 5508? TFTP transfer gives me this error after the upload is done:
% Error: Code file transfer failed - Error while writing output file
*Dec 11 15:11:45.514: %TFTP-3-FILE_WRITE_FAIL: tftp_client.c:517 Error while writing 512 bytes to file. Tftp error.
*Dec 11 15:11:45.514: %TFTP-3-WRITE_NOCLOSE_FAIL: tftp_client.c:147 Error while writing the local file: No space left on device
*Dec 11 15:11:45.514: %OSAPI-3-FILE_WRITENOCLOSE_FAILED: osapi_file.c:582 Failed to write 512 bytes (FileDesc:64). file write no close failed
View 6 Replies
View Related
Mar 5, 2013
The router had firmware 2.0.x(?) and I tried to update to the latest FW, according to the webpage that's
FW_E1000_2.1.02.006_US_20130115.bin
Hardware is E1000 v2 according to sticker on back.The firmware update failed (no reason given) and the router now hangs in limbo where all it does is flashing the power LED.I set my PC to 19?2.168.1.2 and TFTP'd the firmware over to 192.168.1.1 - no errors reported and 192.168.1.1 is pingable. Held reset for 30s, then powered down the router for another 30s. On power-up the router still flashes the power LED.
View 3 Replies
View Related
Jan 28, 2009
I tried to find the radiation pattern for the 1140 AP, but no luck so far. Where to find it?
View 7 Replies
View Related
Apr 18, 2012
I need a legible radiation pattern graph for the 1140 AP -- the antenna pattern. This is for a wireless deployment application which models signal strength. It needs to be specific for the 1140 AP as the antenna has a Maximum gain of 3 dBi which is different than the antenna gain on the 1130 AP.
View 2 Replies
View Related
May 23, 2012
I am trying to create a passcode for 1 IP Phone in a Network and have the following configuration in place as shown below: The plan is that when this IP Phone wants to dial out they will have to dial out the a 4 digit number 5798 followed by the number they want to dial out.The Router i am using is a CCME.
View 1 Replies
View Related
Aug 22, 2011
1. Cisco Aironet 1040, 1140, 3500i Series Integrated Antennas Diagrams show Azimuth Plane Radiation Patterns and Elevation Plane Radiation Patterns when AP is mounted vertically on the wall (red LED above Cisco logo). So "Zero" on Azimuth Plane points to direction rectangular to AP's case plane (mounting wall plane), "Zero" on Elevation Plane points to ceiling and "180 degrees" points to floor?
2. Radio waves polarization in this case would be linear, in direction from ceiling to floor?
3. If AP would be mounted horizontally on the ceiling, then polarization would be in direction parallel to floor axis X and rectangular to floor axis Y? So induced signal on notebook integrated antenna, oriented rectangular to floor axis X, would be near zero?
View 5 Replies
View Related
Oct 24, 2010
I am trying to locate the radiation pattern for a 3502 with an internal antenna. We have some high ceilings so the elevation pattern could impact our placement strategy.
View 6 Replies
View Related
Jan 26, 2012
I have a secondary router (E1200) on my home network, connected LAN to LAN. I use it mainly for wired connections, and it does work for that. But when I try to access this router through the IP address, I get a page that says only "ACT_IDLE". Occasionally, I am able to access, but I've found no pattern to when the router is accessible and when it is not...mostly not.
View 1 Replies
View Related
Nov 11, 2011
When I upgrade the ios on switches, I just create int vlan1 assign it an ip and subnet, then tftp to my pc that is plugged into the switchport using the download-sw command.
I am not sure how to do this on the asa. Do I just plug my pc into port 0 which the documentation says is mapped to vlan 1 with and ip of 192.168.1.1? I tried this by making my pc's ip 192.168.1.2 but am unable to ping the asa. Do I have to change the security level or anything?
View 1 Replies
View Related
Apr 26, 2012
Any diagram showing the antenna position or signal pattern from the EA2700? I know that Cisco recommends that the unit be placed "near the ceiling" but I'm looking for more specific information. Should the unit be mounted vertically or horizontally.
View 1 Replies
View Related
Jan 2, 2012
I have the BEFSR81 V2 and every day at least one of the ports become inactive and the router has to be unplugged and plugged back in to reset the ports. I was going to upgrade the firmware from version 2.44.2 to the one on the site 2.45.10 but when it is downloading I get a message at the end upgrade file pattern error. There is a problem with the router that the ports go out or will the firmware update hopefully correct that issue and how to I get the firmware to update
View 2 Replies
View Related
Mar 14, 2013
I just got an ASA 5505 with Cisco Adaptive Security Appliance Software Version 8.0(4) alredy loaded on it. Should I update/upgrade it to the newest IOS release, or is the 8.0(4) good and stable?
View 3 Replies
View Related
Jan 30, 2012
I have problem that ASA5505 cannot update the time to the NTP which I set to local host connect with the ASA.Refer to the picture below, the ASA time cannot update to 10:49 from 10:29 accordingly. I already set the NTP address to the local host IP address.It can be seen at the NTP at the ASDM as well as the command line below :ntp server 192.168.50.6 source dmz.
View 4 Replies
View Related
Jan 19, 2012
I am having Cisco 3845 series router with c3900-universalk9-mz.SPA.151-4.M2.bin IOS . I want to install new Licence on it for DATA. When i am trying to install licence on it i am facing the error "% Error: License installation failed with error: XML parsing failed".
View 4 Replies
View Related
Jun 13, 2013
we have a asa that block some ip dresse with this reason ( Drop-reason:(no-adjacency ) No valid adjacency ) and when i check the log i found this message for the same blocked ip adresse when they try to make dmvpn tunnel wyh the hub . Routing failed to locate next hop for UDP from MPLS:10.0.104.53/500 to MPLS:10.5.250.251/500 i inform you that the ip adresse of the hub (10.5.250.251 ) is connected in DMVPN Interface not MPLS ,and tha ASA is configured with na nat-cotrol command .nat is not configured.
View 4 Replies
View Related
Jun 7, 2011
We saw this syslog on ASA5585 with version 8.4(1). I have two HA firewall pairs (contains 4 ASA5585, active/standby), and I saw this message on the standby ones.
Jun 7 07:36:26 10.99.96.32 last message repeated 4 times
Jun 7 07:36:26 10.99.96.32 :Jun 07 07:36:26 HKST: %ASA-ha-3-210005: LU allocate connection failed
[Code]....
View 4 Replies
View Related
Jun 14, 2012
I have two interfaces connected to two different subnet - interface 0/1 = 10.100.1.0/24 , interface0/2 = 10.100.113.0/24 as they are direct connected to the ASA i assume i dont need to add an static route but when i try to ping from one interface to the other (ping inside 10.100.113.1) i get "Routing failed to locate next hop". [code]
View 1 Replies
View Related
Apr 16, 2013
I have new ASA 5520 from the box and i have configured already int g0/1 with ip 10.15.14.5 255.255.255.0 nameif inside kindly see details below the config
[code]....
View 4 Replies
View Related
Jun 5, 2011
I have a little problem with my ASA 5510 version 8.2(1) with a IAS server RADIUS for strong authentication.
I have configured a double authentication for my client to access SSL portal:
First authentication: AD serverSecondary authentication: IAS for my token SAFENET ALADDIN The server IAS is declared on a W2K3 and it's standard.
The problem I have is that after more than 24hours of unutilization, when i try to log in, my authentication failed the first time and then the other tries work fine as long as I use it in a period of 24hours.
I first thought about the timeout so i tried to put a "timeout" of 15seconds for AD and IAS servers and a "retry intervall" of 3 seconds, it doesn't change much.
Is there a tool/option in the ASA to check connectivity with the radius every 1h for example.
View 4 Replies
View Related
Apr 27, 2009
I would swear this worked at one point. I have a corporate office, and I have IPSec tunnels out to my outside offices. The corporate office has an ASA5510, and most of the remote offices are running off of Pix506s, one office has an ASA5505.
When anyone connects through WebVPN, using AnyConnect or not, they can contact any of the cifs shares for servers inside the corporate office. They cannot, however, contact cifs shares on servers that are in the remote offices.
View 4 Replies
View Related
May 16, 2012
Im upgrading a asa 5510 from 8.3 to 8.4.
I know from 8.2 to 8.3 was not a mirror update because of nat and access-list but is from 8.3 to 8.4 a mirror update or is there anything which I should be aware of?
View 5 Replies
View Related
Mar 4, 2011
Here are the configs for failover:
PRIMARY
failover lan unit primary
failover lan interface failover GigabitEthernet0/3
failover interface ip failover 192.168.3.1 255.255.255.0 standby 192.168.3.2
failover link failover GigabitEthernet0/3
failover
SECONDARY
failover lan interface failover GigabitEthernet0/3
failover interface ip failover 192.168.3.1 255.255.255.0 standby 192.168.3.2
failover lan unit secondary
failover
In the above configs is it i m missing something for failover? when i shut the INSIDE interface of Secondary ASA I get the below output, It shows me secondary failed and primary Active, WHY it is showing me FAILED instead of STANDBY/READY. What i know about firewall failover is when active goes down the other becomes standby unit but in this scenario it is showing me FAILED,
FW0001(config)# sh failover
Failover On
Failover unit Secondary
[Code] ....
View 8 Replies
View Related
Oct 8, 2012
we have two ASA5520-AIP40-K8 in our office and we purchase IPS service for one only, can we also update the signature of second device before purchasing additional IPS Services for second unit
View 1 Replies
View Related
