My 1 day old WAG160N doesn't seem to want to work after upgrading the firmware. Its the V2 Annex A so I made sure I had the right file, followed the instructions on the site and all went fine, router updated and rebooted. After the reboot I held the reset button for the 30 seconds as suggested, plugged in the ethernet to my laptop and popped in the CD to set it up again.Going through the setup it got to the point of detecting the router and could not find it, checked the lights on the router and the only one lit is the ethernet that the laptop was plugged into, none of the others were. I switched off the router and turned it back on, the power light and the ethernet lights all lit up, then the power light went red and a few seconds later went off. Ethernet light was still on.
i trried te update the firmware of my WAG160N. I had to choose between two versions. I tried both. But both versions give the message that is the wrong version and the installations stops.
I have a WAG54G ver 1.2, 4-port eth + wireless adsl router. The latest firmware update on the support download site is Ver.1.02.1 from 05/18/2004 which is ridiculous! [URL] This is the ver I have installed on the router and lt does not even have WDS setting, so the device is more or less useless.I have checked open-source alternatives (the wrt line) but they all start with WAG54G V2 and none support the earlier models v1 and v1.2 I need to somehow upgrade this router to something functional. I have checked the GPL code page as well and while there ls a listing for WAG54g, I think itd for V3 routers. So the question is:
1. Is GPL source code usable on v1.2 (I assume not)
2. any suggestions to get a wds system on the router (including beta / alpha firmware)
I would like to know if I have to do the firmware update this is my second WAG54G2 router I did the firmware update on the old 1 and it failed so I RMAed it the only problems im having with it is slow transfer speeds over the wireless network and it disconnects from the net now and then. I also would like to what hardware should I use to get a 108mbps over my network because 54mbps is just too slow. I used windows 7 and mozilla to do my frimware upgrade and it failed.
I've just attempted to uprade the firmware on my WAG325N from 1.0.6 to 1.0.12 the latest, over wireless. It will not work with Ethernet. It started to upgrade and failed with a garbled screen in my browser. No message to reset. Tried a complete reset several times. Pressing reset, power off for 30 secs. When I attempt to connect wirelessly with browser, just get a garbled screen, with no menus.
The router had firmware 2.0.x(?) and I tried to update to the latest FW, according to the webpage that's
FW_E1000_2.1.02.006_US_20130115.bin
Hardware is E1000 v2 according to sticker on back.The firmware update failed (no reason given) and the router now hangs in limbo where all it does is flashing the power LED.I set my PC to 19?2.168.1.2 and TFTP'd the firmware over to 192.168.1.1 - no errors reported and 192.168.1.1 is pingable. Held reset for 30s, then powered down the router for another 30s. On power-up the router still flashes the power LED.
I just downloaded and tried to apply the latest Firmware update to my dcs-930l. It failed or timed out. Now the camera is unusable. I tried the hard reset, several times, holding it in for 10 seconds after 3 seconds did not work. I held it in for 3 seconds, waited 1 minute, and just got a flashing red light. I did the same thing after holding reset in for 10 seconds. I have unplugged and replugged in the network cable on both ends several times and turned the power off and on on the router and camera several times. The camera only blinks with a red flashing light. Is it a brick now? Is there any other magic tricks to try?
i tryed to update my rv120w from 1.0.2.6 to 1.0.4.10 after about 15 minutes i power cycled the router.it now has alternating green power and wireless lignts flashing and router is unresponsive.
it does not give out ip address and not reachable when seeting static ip on cpui have tried the reset button.Can this unit be recoverd somehow?
I just bought an RV220w. My first act was updating th firmware to 1.0.2.4. Unfortunately I was not able to configure the router for vlan purpose 'cause the "Port VLAN" point was missing in the webinterface. I performed several factory reset but it didnt work for me - so I got back to firmware 1.0.1.0.
Have an SRW2024 that I was updating firmware and it got interrupted. Now I can't access the switch from either console or IP. Switch will not pass traffic. Is there a way to get this switch completely reset so I reconfigure and use it again?
Had just purchased a new DCS942L unit and had it setup fine. Registered it on the web and the web stated that it needed a firmware update. Connected with hard line and started update. After 5min webapp said device timed out. When I went to rest camera could no longer get a connection of any kind.
I have a WAG160N wireless gateway . Yesterday when i tried to power it on after a couple of seconds the power led was solid green and the Ethernet leds were blinking with no Ethernet cable attached to the router . The ethernet leds would keep blinking for minutes . I tried to use a screwdriver to do a hardware reset ( with power on ) and i noticed that the power led would start blinking green/red for minutes . I tried to use another wired router which i have for backup and it could connect to the internet normally without a problem.
What the green / red blinking power led means ( power led is green and then changes to red and then it starts over ) ?
I've just been sent a new ADSL modem router by my new broadband supplier and plan on using it. However, my question is, can use my old wag160n to replace one of these, which im currently using to connect an old xbox to my wireless network, but also make use of the other lan ports on the wag (i.e. Connect more than one non wireless device to the wag and gain access to my wifi network?)
I've a 20Mbit/s connection with Telecom Italia provider.My line values follows:-- DSL Information ---DSL Driver Version: AnnexA version - A2pB023k.d21dDSL VPI/VCI: 8/35DSL Status: ShowtimeDSL Mode: ADSL2+DSL Channel:DSL Upstream Rate: 979 KbpsDSL Downstream Rate: 22105 Kbps Down upDSL Noise Margin: 12.0 dB 13.4 dBDSL Attenuation: 10.5 dB 4.3 dBDSL Transmit Power: 14.0 dBm 12.4 dBm?I have issues about connection stability : on HEAVY load download the PPP connection goes down. The sync signal stays up, but the PPP goes down!
In the log these lines corresponds:
Sun, 2013-01-20 23:29:29 - No response to 3 echo-requests Sun, 2013-01-20 23:29:29 - Serial link appears to be disconnected. Sun, 2013-01-20 23:29:29 - Enter: tdb_store. Sun, 2013-01-20 23:29:29 - tdb_store: calling tdb_update. Sun, 2013-01-20 23:29:29 - Enter: tdb_update.
[code]....
My ISP says that there are no troubles with the line and it can be an issue of the modem...
When I enable the debug with ?todo=debug shall I see more info in the logs ?How to stop the debugging ?How to print the logs ?What is the difference with debug and ppp_debug ?What is the effect of the sendlog command ? I didn't receive any email with a log !
Struggling to enable Airplay using a WAG160N. Any settings I need on the router? Looking on forums, came across suggestion to disable WMM support. This seemed to work and i had Airplay but now I've lost it again.
I hard reset the router WAG160N and i can't access it on 192.168.1.1, i can connect to the wireless connection but it shows unindentified network, in properties gateway IP is absent. i also get 169.254.1.38 as IPv4.What could have happened to the modem, I can't use it at all at the moment?
Two years ago I bought a WAG160N for modem (ADSL) and router functionality. I consider to buy a pure router (E3000 or E4200) to connect to the WAG160N and use that one purely as the modem. How and what should I configure/disable on my WAG160N?
I can no longer access the internet, and the internet has been difficult to bring up for one to two weeks.Internet light does not come on. Under Status tab, interface is down, tried refresh and connect but nothing.The IP address can be pinged, 4 packets sent and 4 packets received. Tried resetting defaults and refreshing but no success.Bought this router in September 2008 to replace WAG54G which was constantly turning on and off every few seconds.
Some years ago i have buyed a WAG160N i haven't never used, because once i plug it power, it start to reboot and reboot in a loop...Is there something to do with it or should i put it in the trash ? Firmware using is probably Ver.1.00.15?
I have a WAG160 setup to use the one fo the LAN ports as a WAN connection. The issue is every now and again the internet connection drops and it seems it is unable to communicate with the DNS server that is providing the internet connection.
Any hardware that can re-boot a DSL router such as the WAG 160N when the router no longer passes traffic ? Today, while the DSL line and the Internet appeared to be working, I could not log in to the router from a LAN machine and I had to power it off and on again by hand.We have a number of surveillance cams on the LAN and this must not happen, that the cams cannot be accessed, in particular if nobody is on site for a few days.Unfortunately, the WAG 160N does not have a daily re-boot option. What can one do except for installing a timer that switches the power to the router off and and on again ?
I'v just changed my internet provider. That new one uses Annex b, my wag160n is purposed to annex a. Thats what i'v done. Turn on bridge mode turn off dhcp, set PPPoE with my login and password. And here is my problem. I cant connect by wifi with more then 1 device. I can only connect with my laptop when i'm trying to connect on my xbox it says it cannot get ip adress from router. What shoudl i change ?
I purchased a new WAG160N router a few months ago and recently I have been having major problems with connectivity.The problem is that it resets itself at seemingly random times. I see it happening. The red power light starts flashing red and then the other lights slowly turn green as it re-establishes connection to the internet.
This is becoming extremley frustrating as I do online gaming with my XBOX 360.I use wired connections using ethernet cables. One to my laptop. And one to my XBOX 360.I have contacted my ISP who have done line checks and I have had an engineer look at my line and all is good. I have also replaced all cables to/from the router including phone cords and ethernet cords. EVERYTHING is new.I recall one incident in which my internet was down and I just couldnt get connection AT ALL. I rang my ISP and they got me to log into my modem settings. The settings were all altered for some reason and I have no idea why. When they told me to enter the details in the settings the internet worked immediatley.
I have a wag160n and would like to disable the wireless and use as a wired ASDL modem. I can't see any obvious settings I'm the setup or buttons on the unit but was wondering if I were to set the DHCP to disable if
My Linksys WAG160N has worked fine for 2 years however all of a sudden when I power it up it's start normal but after 4 seconds all ethernet lights blink one time and all start from the beginning, it's like it reboot every four seconds.It happens so quick I can't even get to the Internet/Network Settings in WIndows Control Panel.I have tried accessing router setup and installing firmware and both have failed - it can not find the network address.If I try to reset with the reset button on the rear (30sec reset), it stops rebooting and the power LED starts to blink red/green and the ethernet LED of the port where my cable is connected starts to blink alsoI have set IP address manually on my computer as per the Cisco support pages (192.168.1.1), still no response from ping.I have also tried to reinstall firmware using TFTP but it also fails because it can not find the network address.
