D-Link DCS-930L :: Firmware Update Failed / Timed Out
Jul 1, 2011
I just downloaded and tried to apply the latest Firmware update to my dcs-930l. It failed or timed out. Now the camera is unusable. I tried the hard reset, several times, holding it in for 10 seconds after 3 seconds did not work. I held it in for 3 seconds, waited 1 minute, and just got a flashing red light. I did the same thing after holding reset in for 10 seconds. I have unplugged and replugged in the network cable on both ends several times and turned the power off and on on the router and camera several times. The camera only blinks with a red flashing light. Is it a brick now? Is there any other magic tricks to try?
View 7 Replies
ADVERTISEMENT
Sep 2, 2011
The firmware update went smoothly The mydlink service quit accessing the camera, until I download and ran the updated Mac version of the "mydlink Setup Utility v1.0.06_07272011"Seems as if the camera is more stable; ping times are more consistently low.
View 2 Replies
View Related
Sep 20, 2011
Received a replacement DCS-930L today; using WPS, did setup wirelessly; all OK. Then did firmware update wirelessly (with second, DCS-932L, turned OFF). The v1.03 firmware file was the same one I previously used, I think. Amazingly, The camera menus are now in French, and I can't find a setting to change it to English.
View 1 Replies
View Related
Jan 17, 2012
Had just purchased a new DCS942L unit and had it setup fine. Registered it on the web and the web stated that it needed a firmware update. Connected with hard line and started update. After 5min webapp said device timed out. When I went to rest camera could no longer get a connection of any kind.
View 1 Replies
View Related
Jan 19, 2011
My 1 day old WAG160N doesn't seem to want to work after upgrading the firmware. Its the V2 Annex A so I made sure I had the right file, followed the instructions on the site and all went fine, router updated and rebooted. After the reboot I held the reset button for the 30 seconds as suggested, plugged in the ethernet to my laptop and popped in the CD to set it up again.Going through the setup it got to the point of detecting the router and could not find it, checked the lights on the router and the only one lit is the ethernet that the laptop was plugged into, none of the others were. I switched off the router and turned it back on, the power light and the ethernet lights all lit up, then the power light went red and a few seconds later went off. Ethernet light was still on.
View 1 Replies
View Related
Nov 28, 2012
i tryed to update my rv120w from 1.0.2.6 to 1.0.4.10 after about 15 minutes i power cycled the router.it now has alternating green power and wireless lignts flashing and router is unresponsive.
it does not give out ip address and not reachable when seeting static ip on cpui have tried the reset button.Can this unit be recoverd somehow?
View 2 Replies
View Related
Sep 25, 2011
I just bought an RV220w. My first act was updating th firmware to 1.0.2.4. Unfortunately I was not able to configure the router for vlan purpose 'cause the "Port VLAN" point was missing in the webinterface. I performed several factory reset but it didnt work for me - so I got back to firmware 1.0.1.0.
View 9 Replies
View Related
May 10, 2011
Have an SRW2024 that I was updating firmware and it got interrupted. Now I can't access the switch from either console or IP. Switch will not pass traffic. Is there a way to get this switch completely reset so I reconfigure and use it again?
View 1 Replies
View Related
Oct 19, 2011
I upgraded the firmware per one suggestion, but no difference.I am going thru the setup wizard with ethernet cable attached. I want to use them wirelessly so I clicked wireless setup, and entered my network info. At that point I get an error message saying it failed to save settings. I know the ID and password are correct.I have tried exiting the setup wizard and accessing the camera thru the web interface. All wireless settings are correct. The camera works FINE on web browser, myDlink, and even my iPhone app as long as the ethernet cable is attached.Other wireless devices have no trouble connecting to my router. Is there some setting on the router that can be preventing the connection? I've done some trial-and-error changes, like different ports and enabling/disabling UpNp on both camera and router.Oh and almost forgot to mention.I did call tech support, which was a joke. Some foreign lady was reading off a script that told me to reset, unplug, reboot everything. Then she gave me a case# and said upgrade the firmware.
View 11 Replies
View Related
Aug 16, 2011
Now that the DCS-930 has a dedicated board, we can restart our firmware wishlist.
View 14 Replies
View Related
Jun 28, 2012
D-Link released firmware version 1.05 build 08, located here: Firmware v1.05b08
View 2 Replies
View Related
Mar 5, 2013
The router had firmware 2.0.x(?) and I tried to update to the latest FW, according to the webpage that's
FW_E1000_2.1.02.006_US_20130115.bin
Hardware is E1000 v2 according to sticker on back.The firmware update failed (no reason given) and the router now hangs in limbo where all it does is flashing the power LED.I set my PC to 19?2.168.1.2 and TFTP'd the firmware over to 192.168.1.1 - no errors reported and 192.168.1.1 is pingable. Held reset for 30s, then powered down the router for another 30s. On power-up the router still flashes the power LED.
View 3 Replies
View Related
Oct 28, 2012
I've not found any topic related to what happened to me. Bought two cameras and upgraded the firmware on both as asked, but one of them just stopped. The light is solid green and not red like other posts.Tried the recovery procedure, but the browser won't find my camera. Changed computer IP and everything else that was told to be done. Nothing works!! I also can't find any posts relaled to my problem all over the internet.
View 3 Replies
View Related
Oct 1, 2012
I have REV A and the firmwars version is 1.04. I want to upgrade to ver 1.35. I have downloaded the firmware to my computer. When I login to the router page and go to the firmware tab, when I try to click browse for the file nothing happens. I have tried using Internet Explorer and Firefox.
View 2 Replies
View Related
Nov 12, 2011
I have a DIR-615 router, hardware rev. C1 running firmware v. 3.10, dated 4/17/09. I've been beating my head against the wall trying to get this router to properly forward ports for a bit torrent application, but it not only won't do that, it doesn't want to save DHCP reservations and it doesn't want to recognize my computer on the LAN if I set a static IP address (although it does allow my computer to connect and get an internet connection). From the D-Link website, the description of firmware update 3.12NA looks like it might take care of these problems, but I can't get the router to update. When I log into the router and check for updates, it returns a message saying the latest update is v. 3.11, dated 9/15/09. However, when I attempt to download the update, nothing happens. The D-Link website offers update 3.11NA (4/20/09), 3.12NA (3/8/10), and 3.13NA (9/30/10). Why does the website offer me a different update than the router itself? I downloaded 3.13NA and unzipped the folder, which has a text file and a .bin file; I presume the latter is the update. However, when I browse to this file and attempt to upload it to the router, nothing happens. How the heck do I update this router?
View 5 Replies
View Related
Jun 5, 2011
My roommates and I keep getting knocked off the internet every few minutes on the router so I've tried a bunch of the tricks found here and am trying to also update the firmware. I downloaded the newest firmware, uploaded it to the router and it says it succeeded in the update, but then after reboot gives the same version it came with.
View 1 Replies
View Related
Aug 5, 2012
I tried to proceed with the update of the firmware on my DIR-835 router. I want to install version 1.0.2 of the firmware.I tried without success with Chrome and IE9. I get to a blank page and nothing downloads IE9 A PDF file is downloading but not the firmware update itself
View 1 Replies
View Related
Dec 7, 2012
I am currently on fw 1.33NA and it works fine just want to update so it works better I've tried the reset to factory and unplugged the internet port and ive tried fw 2.0NA and 2.10NA
View 2 Replies
View Related
Feb 21, 2012
updating to 2.03NA seems to be working for a lot of people. Anyway, my current NAT type is Strict ugh. I used to have a DIR-615 router. Man oh man that worked so well. But I had to replace it since it conked out after a 6 year stint.
View 1 Replies
View Related
Dec 7, 2011
I have dap-1522 version A Browser IE8 with lestest updates.
I downloaded the DAP1522_FW_1.31zip went I try to upload via the 1522 admin error not correct file.
I try three different way to download it, could the file be bad on dlinks web site?
View 4 Replies
View Related
Oct 3, 2011
I just bought my DIR-825 from Frys and it came stock with 2.02NA B1 firmware, but everytime I try to update it to 2.03/2.04/2.05/2.06 it errors saying it might not be the same hardware or something on the lines of that. But now when I try to upload it, it just leads me to "192.168.0.1 was interrupted" and can't even get to the error screen now.I'm not too savvy when it comes to routers, especially a D-Link since previously I had a Linksys WRT54GL
View 15 Replies
View Related
Apr 27, 2010
Currently running firmware version 1.32NA on DIR-655 (hardware version A4). I have made multiple attempts at updating its firmware, first to 1.33NA and later to 1.34 Beta 3, with no success: on each occasion, it accepts the local .bin file upload, then claims to be in the process of applying the upload (with I think an 80 second countdown), and eventually comes back to the login page, still showing that it's running firmware v1.32NA (verified after logon, refresh, etc -- no update was applied). I have attempted this immediately after a soft reset of the router and even after a hard (power cycle) reset, but still no success.
(Any reason to think that the update might work if performed while the router is disconnected from the Internet? or after a configuration reset?
View 14 Replies
View Related
Apr 24, 2011
I bought my DIR-825 three months ago. The firmware seem to be from 2009, and the check-for-later-firmware functionality from the web interface tells me that my version (Current Firmware Version : 2.01EU) is the latest.
I don't believe that the firmware from 2009 is the latest, but have no idea on how to proceed.
My hardware in the web interface say this: (Hardware Version: B1 Firmware Version: 2.01E
The problem I really have is related to PPTP pass through (I think), but I thought making sure I have the latest firmware is always a smart move.
So, can the firmware-checker of the web-interface fail, or do I have the latest firmware?
View 6 Replies
View Related
Mar 31, 2013
I've been having wireless range issues lately with my dir-615: a lot of holes seemed to have popped up in my house despite nothing changed (house or router location). This is after at least 2-3 years of good coverage and no issues. Went to look at the firmware & found 2.0 installed. Found out online that (I think) firmware is now at 4.11. Tried to download and install but both finding the update and unzipping it proved challenging. Specifically for the latter, unzipping kept yielding more zipped packages, like a russian doll
View 1 Replies
View Related
Sep 2, 2012
I get this error when I update to 1.12. Error 324 (net::ERR_EMPTY_RESPONSE): The server closed the connection without sending any data.
View 3 Replies
View Related
May 16, 2013
I updated my dir-655 firmware to 1.36WW after the update I the router has been restored to factory settings and every time I try to change any setting it gives me: "ap should not be locked before configuring". I cant change set any configuration, cant change even the router time!I logged in to the router as admin and left the password blank.
View 2 Replies
View Related
Jan 22, 2012
I read the sticky related to firmware updates. I have a DIR-655, that has been been giving me good service for quite a few years. I subscribe to the "if it ain't broke, don't fix it" philosophy as I have managed to keep my home network and computers running over the years, but I'm not knowledgable in these matters. I am still running firmware 1.10, and have not wanted to take a chance that if I upgraded I would find myself with numerous devices with no connectivity (running mix of Mac and PC desktops and laptops, XBox, Wii, Roku box, numerous iPhones and iPods, LG TV, and an iPad).
Recently I moved to the cable company phone, and they added a new modem. They have it set as a gateway (I think that is the terminology), and my network works basically as it did before. I have noticed though, that my Roku box, laptops, and skype on my Mac desktop seem to be having periods of slower download (Roku box), skype choppiness, and download that stop. I was thinking that perhaps if I upgraded the firmware, my performance might improve. After reading the sticky, it seems like firmware may not be the answer. This is a reliable but older piece of equipment, and now I'm thinking that I just need to upgrade to a newer and perhaps more advanced router.
View 1 Replies
View Related
Feb 15, 2013
I am using DIR 615 Hardware Version JX... When I check for an update to FIRMWARE I get the following message, "Did not get information".In the past when I clicked on there may be a firmware update on our site. I was taken to [URL] which gave me an 401 error and now redirects me to the US d-link page. Which doesn't even list Rev Jx as an option.I am having a lot of trouble with this router in regards to VPN and must have in China, and am hoping an update is available. [code]
View 1 Replies
View Related
Sep 1, 2012
Today i has tryed to update the firmware of my DIR-655 router, but in the screen under the administrative tools menu there is nothing to use.
how do I update the firmware and bring up all the necessary tools?Dir-655 works because they are connected to the internet and manages the wireless network.
View 2 Replies
View Related
Mar 15, 2013
Region : Argentina
Model : TD-W8968
Hardware Version : V1
Region : UnitedKingdom
Firmware Version : 101029
ISP : TalkTalk
I have version 1.1 and d/l'd firmware 111125. The upgrade ran successfully to 100% and then I got the login screen again. However after checking, then restarting to factory default the version displayed was still the old one
View 3 Replies
View Related
Jan 19, 2012
Have DIR-655, HW A3, F/W 1.10. On the Advanced tab, there is no Guest Zone option. Can this be fixed with a firmware update? If so, which one?
View 2 Replies
View Related
May 1, 2011
I tried to update my firmware on my DIR 615 by clicking the check now button within the routers parameters and got the file DIR615C1_FW311NAB04.bin The update bombed. I have hardware ver. C1 Firmware ver. 3.11NA dated June 23, 2009.Should I try and install the other firmwares in subsequent order, i.e. ver 3.11NA (dated 7/15/2009), then ver. 3.12 and then ver. 3.13 Or should the latest and greatest cover them all?
dwest.Wireless to router. No factory reset. ISP Ser. Cable ISP Router. Stand Alone.Modem Make & Model. I have to get up for that one, will have to report back tomorrow.
View 4 Replies
View Related
Oct 10, 2011
I have a DIR-655 router running 1.21. The last couple of years, I've always been checking the firmware version by pushing the "Check Now" button on the web management - it has always responded with "This firmware is the latest version. " I've been researching networking monitoring tools and came across this link: [URL] It requires that you update to the latest firmware - and this time I sued on the on-line link - and it turns out that the firmware version for my device is actually 1.35NA?So... first question is - why does my router tell me that 1.21 is the current version?I'd like the network widget - what are pros/cons of updating from 1.21 to 1.35NA?Have there been fixes to the scheduling portion? - 1.21 cannot handle 24-hour time properly. I also have to reset the router daily - sometimes more often - due to problems when used wirelessly. (Fortunately I try to use wired as much as I can.)
View 8 Replies
View Related
