WRT120n Cisco Wireless Router Keeps Booting Off From Network
Apr 25, 2012
my wrt120n cisco wireless router keeps booting me off my network.it is next door usually have a great signal but fades in and out the box for router says its for wireless n.....all i can get is g.can i manually change the settings and should i get a signal booster or a bigger and better wireless router? then i go power cycle my routers and modem and it will sometimes work and sometimes not wifi is next door but less than 50-60'.
View 1 Replies
ADVERTISEMENT
Jun 26, 2011
How to time access restrictions with WRT120N router a wireless network?
View 7 Replies
View Related
Jan 20, 2012
just brought this router model #wrt120n and can't get setup disk to install because it says i have no ethernet port
View 1 Replies
View Related
Jul 19, 2012
I have a Linksys WRT120N which had suddenly and unexectedly stopped working after disconnecting my roku box. I didnt worry about it until I got an Iphone and now .I was able to re-establish the wireless connection on my netbook today after a ton of research and messing around with the settings and then downloaded network magic, which finally fixed the problem. I believe that it automatically transmitted the WEP key to the Netbook, which is what I am missing when I try to log into the network on the Iphone.How do I get this password to show up on Network Magic? When I look at the settings, it does not show the actual numbers, they are hidden.
View 6 Replies
View Related
Aug 23, 2009
I just bought a WRT120N and at different times it will randomly restart and disconnect all the computer on my network I have 4 wired devices and 4 Wireless devices.
View 9 Replies
View Related
Jan 6, 2013
I got error message everytime i try to configure home network defender and i tried to find the solution but no luck but everytime i click and enter my email and password i get this message, i bough this router recently and the only troubles i have is with this
View 2 Replies
View Related
Jan 27, 2013
I am trying to extend my home network into my basement with both wired and wireless connections. I have a WRT120N upstairs, which is connected to my cable modem. I have an E1200 in the basement, which I have connected with a LAN port. DHCP is turned off, and all wired connections are getting an address from the upstairs router, and connecting to the internet successfully.I've configured the wireless with the same SSID on both routers, but the clients that connect to the downstairs wireless are not able to access the internet. They are getting an IP address from the upstairs router, but can't get past the gateway.
View 1 Replies
View Related
Aug 6, 2011
Is it possible to configure the apple airport express to extend a linksys wrt120N wireless network? if so how?
View 2 Replies
View Related
Nov 21, 2011
I have linksys WRT120n (just bought it) now connected with ethetnet cable i have a laptop and an 2 iphones that wont connect the network after a while, the only way that solves the problem for a while is unplugging the router from the electricity and plugging it again and then after few hours or a day the problem returns.
Client Lease Time: 1440
the devices have an IP reservation
network mode - mixed ( B G N )
View 5 Replies
View Related
Jul 15, 2011
The old configuration was a Linksys/Cisco WRT120N plugged into a NETGEAR ProSafe VPN Firewall FV336GV2. I will list the settings below, but the short of it is that the WiFi router was in charge of getting the wireless clients but the Firewall was the one that assigned IP addresses and all that. This setup worked out just fine except that the WiFi router was in the basement and clients could only connect to it while still in the basement. They wanted to be able to connect to the network wirelessly while on the third floor, but couldn't even see the basement router from there. We shipped out an identical router configured beforehand exactly the same way, save for its MAC address and local IP address (those having premonitions, during troubleshooting I try setting different radio channels as well). The client plugged an Ethernet cable from the wall to port #2, and a desktop to port #3.
The desktop has internet access. Wirelessly, however, had issues The client only had a single laptop to test with, an XP SP3 machine. Unfortunately I couldn't pull specs from it as of this post, so I don't know if it connected by G or N. This laptop, which worked fine in the basement, wouldn't connect upstairs (it would sit trying to get an IP address forever) until I had him "forget" the basement network. At this point, he was able to connect to the upstairs router and access the internet. However, he could then no longer use the access point in the basement. I tried the same troubleshooting steps, like having him delete the wireless profiles from his network card and rebooting the router, but he couldn't even see the basement router while down there anymore.
Occasionally, it would show up for a moment, then disappear before he could connect to it. To make sure it was the basement router that was briefly appearing, I renamed the upstairs router to something else; this confirmed that indeed it was the basement router that was doing the "now you see me, now you don't" act. I then tried setting the basement router to Channel 1 while leaving the upstairs one at Channel 6. Still nothing, even though the laptop was about 25 feet away from the basement router and I had him wipe the wireless profile again. Rebooting the computer didn't solve the issue either. After this, I named the upstairs router back to the same as the downstairs one and had him go upstairs to test; he could connect to it right away.
I figure this is either a configuration issue on the laptop or routers (or firewall). Unfortunately, there weren't any other wireless clients to test with, and I'm not sure there will be when I continue troubleshooting on Monday. By the way, I looked for a "bridge mode" option on the WRT120N and couldn't find one; I'm told that the firmware doesn't support it. I don't feel comfortable putting on alternative firmware unless it's literally the only thing that will solve this. The configurations for the networking equipment are listed below.
NETGEAR ProSafe Firewall:
IP Address: 192.168.50.1
Subnet Mask: 255.255.255.0
DHCP Server: Enabled
Starting IP address: 192.168.50.50
[code]....
View 1 Replies
View Related
Dec 23, 2012
Having a problem where the router will randomly boot everyone off the network and display a "limited access" status. This happens every few hours and it's actually pretty annoying. I downloaded the wireless test and these are my results. If it matters at all, our Router is "Mendes". [code]
View 12 Replies
View Related
Dec 16, 2010
I am using a cisco 2811 router.It is not booting properly.It reboots continously by just decompressing the image repeatedly..
View 2 Replies
View Related
Jan 1, 2011
I have Cisco 1841 Router with no WIC cards and USB.
Image is ipbase and on the flash. When it boots it gives the error and hangs - I changed the register value to 0x2142 but no change happened.
Following are the capture from the router .
System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)
Technical Support: [URL] (c) 2006 by cisco Systems, Inc.
Copyright
[Code]......
View 3 Replies
View Related
Jun 15, 2011
We have Cisco 3945 Router and generating crashinfo while firing PRI from this Router.
View 1 Replies
View Related
Apr 18, 2012
Linksys WRT120N to 811.11n? I set to 811.11N Only with 40Mhz, saved and reboot the device but the signal continuous in 811.11g.
View 3 Replies
View Related
Mar 31, 2013
AP not booting and am not able to boot. Xmodem file system is available.flashfs[0]: unable to allocate available block.
The system has been interrupted, or encountered an errorduring initializion of the flash filesystem. The followingcommands will initialize the flash filesystem, and
[Code]....
View 3 Replies
View Related
May 10, 2012
How to reset the linksys cisco wrt120n router.
View 4 Replies
View Related
Jan 23, 2012
Is Linksys WRT120N still supported by cisco? I ask this because of the WPS "CRITICAL" vulnerability and no news of a patch since a month... and
*WRT120N firmware is propietary
*Not supported by DD-WRT/OPEN-WRT/FREE-WRT
View 1 Replies
View Related
Mar 15, 2013
My Cisco Linksys WRT120N router keeps disconnecting, my family and me are all using the wireless connection. But sometimes the router just disconnect us all, its like its restarting, it only close down for like 5 - 10 secounds and then its back on. Sometimes it does it like every secound hour and sometimes it does it 3 times in 10 min. I usually play games on it and even tho I am the only one using it, it still disconnects. We got 2 wireless cameras running on a secound router that is merged (Thats what the nerd that setted it up for us told me) with the primary existing router. I am not really that good at computer I just dont want to get disconnected all the time.
View 1 Replies
View Related
Jul 23, 2011
Router 1: I have a WRT120N wireless router connected to the Internet. It has IP 192.168.1.1 and DHCP is enabled with address range 192.168.1.100 up.
Router 2: I have a WRT310N router connected to the LAN via LAN port to ethernet jack in the wall (not WAN/Internet port). It has ip 192.168.1.2 and DHCP is DISABLED.
All the devices on my network can see each other. Devices connecter to router 1 can see devices connected to router 2.The problem is, devices connected to router 2 cannot get to the Internet. I verified clients connecting to router 2 are assigned the same DNS addresses and the same gateway 192.168.1.1 as the clients connected to router 1. But for some reason router 2 doesn't know how to router Internet traffic out through router 1?
I tried plugging the LAN cable into the Internet/WAN port on Router 2 but then devices on Router 2 can no longer see devices on Router 1. I've seen discussions of setting up router 2 on its own subnet: 192.168.2.1 instead of 192.168.1.2 but then supposedly devices on router 2 will still not be able to see devices on router 1.
I'm guessing router 2 can't access the Internet because it is default configured to send Internet traffic to the Internet port, no t the LAN port. how to configure it so all devices on both routers see each other and router 2 devices can get to the Internet.
View 3 Replies
View Related
May 18, 2011
I bought a new Linksys WRT120N modem which is working great, but the wireless for some reason isn't working properly. My computer is able to sense the exsistence of the connection tho. I've tried using other computers to connect to it, and still the same problem, can sense but cannot connect.
View 8 Replies
View Related
Mar 25, 2011
I currently have a network using ipaddress 10.1.x.x and 10.2.x.x and 10.3.x.x with a subnet of 255.0.0.0 I purchased 2 of the wrt120n wireless routers for testing and find I can not use the subnet of 255.0.0.0.
View 9 Replies
View Related
Oct 29, 2009
I have a WRT120N and have been trying to set up priorities using the QoS under the tab Applications and Gaming. Everytime I "Save Settings" it does not save. It refreshes the page and deletes everything I just set up.
I did Live Chat and they told me it was my router. I returned it and got another one... Same problem
View 9 Replies
View Related
Sep 5, 2010
I'm using an Static IP adress and i'm using wrt120n router, but to connect the internet i have plugged the internet cable in the 1,2,3,4 (doesn't matter which one) slot. So now i'm just using the wirelss part of the router without "routering" if i can say so. When i put the internet cable in the Internet slot of the router, the laptop just cant connect to internet - it shows Unidentified network without Internet Access. I don't know what type of changes i have to make in the WEB interface of the router. I think i have to set the type of the connection - now is DHCP and may be to put my IP adress, DNS, Subnet mask in the router settings, but don't know how exactly. I've tried to set up the router with the CD-interface but same thing happened - Unidentified network when the cable is plugged in the Internet (yellow) port. How to set up the router to be a router, not just a wireless switch?
View 9 Replies
View Related
Jan 18, 2010
My roommate and I recently got a WRT120N to replace an older Linksys router that was exhibiting the same problems with less frequency. Indeed, the entire reason we got the new router was to fix these problems. Alas, they have become worse.Anyways, what's happening is that the router constantly resets itself. It does this every 20 minutes to an hour and doesn't seem to be related to how much traffic it's dealing with.It's not just the internet going down, it's the entire network, and not even just the wireless part. My computer has a wired connection to the router and, and I get told "A network cable has been unplugged" every time it happens. Then, if I look down at the router, I see no flashing lights, just the steady glow of the power light. It always fixes itself after 10-15 seconds, but it's very annoying. Certainly, playing games online or having a conversation on Skype is made more difficult.As previously mentioned, we replaced our older router because it was exhibiting the same behavior, but the new one does it with greater frequency. At the very least, the router does reset itself instead of needing us to cycle the power. The setup was slightly different with the old router: I was using a wireless connection with a WMP54Gv4 which I've had to disable since it bluescreens the moment it so much as sniffs a signal from the WRT120N?
View 9 Replies
View Related
Aug 20, 2011
Is there anyway to disable WPS on the WRT120N router?
All I can do is switch the "view" from WPS to manual configuration in the management console...this doesn't actually disable anything.Maybe I don't understand WPS security, but what's the point of using a 20 character WPA2 password if WPS has an 8 digit PIN that I can't change or disable?
View 3 Replies
View Related
Mar 17, 2010
I just bought a WRT120N to set up with my new Gateway Windows 7 64-bit using Cablevision cable internet. When I go through the steps from the CD to install, the wizard does not find the connection. When the internet is plugged directly into the computer, it works fine. If I have the router plugged in first and then run the install CD, it picks up the router as an existing router but I can't get it to install
View 4 Replies
View Related
Jul 2, 2012
I have a WRT120N router installed in my office.All PC and Laptops are connected to it via WiFi.there are about 3 PC and 4 Laptops.The WiFi keeps going Off now and then..and comes back on in a minitue or so.
View 9 Replies
View Related
Apr 2, 2013
why are some of the lines solid & others dotted on the map page?
View 4 Replies
View Related
Dec 25, 2011
I removed my ps3 from my network map and now i can't connect it back. How to do it?
View 1 Replies
View Related
Apr 4, 2013
I have a customer that has an air-lap1142. He says that it boot to Rommon, and he has to issue the boot command to get it to boot. What is the rommon command to have the ap boot to the image automatically?
View 1 Replies
View Related
Dec 13, 2012
How to install the Cisco/Linksys WRT120n wireless router with respect to using Roku.I have one computer, a laptop, which I'm using as a desktop, in that it is stationery and the only wireless device is the Roku. When I open Network File Sharing, sometimes i see 2 instances of linksys, other times just 1. general setup or whatever so I don't have to reboot the computer every 2 hours to watch Roku.
View 1 Replies
View Related
Nov 5, 2011
Can you use Cisco Connect Software with the Linksy WRT120N router? My blackberry curve also asks for a guest password and refers users to get the password from Cisco. I have Network Magic installed and it seems to work fine except for communicating with my blackberry.
View 3 Replies
View Related
