Cisco Wireless :: WAP4410N Connection Shows Enabled Instead Of Connected
May 9, 2012
My WAP4410N is configured with 4 seperate SSIDs. Two of the SSID status are showing "Enabled". The other 2 are shown as "Connected". The one that are showing as Enabled are not receiving any packets. Devices connected to the SSID that shows "Enabled" are unable to connect to the network. Any one else encountered similar issues before? This issue just surfaced few hours ago. The device has been using for around 2-3 years with minimal issues.
View 1 Replies
ADVERTISEMENT
Jul 1, 2012
The route is connected to that. Wirelessly, there are two laptops and sometimes an iPad and sometimes a Wii. Verizon DSL. I barely use my laptop during the week, but did notice some connection issues maybe Thursday and Friday nights. All day yesterday and today, as well. I will have a connection for maybe 5 minutes and then get errors loading webpages (and/or videos stopped). I will repair the connection and it will say everything is fine but it will not work, repair again or disconnect/reconnect(sometimes, several times) and then it works for 5 minutes or 20 minutes before the same thing happens. The other laptop is having the same problems. What I have tried so far: restarting the PC, both laptops, the router, and the modem. Resetting the modem. I have not moved any furniture or anything that would cause interference. I am worried because I have been trying to make more money and started at this site called Treasure Trooper which seemed okay-surveys and the like. There were a few pay-to-download things I downloaded but did not run. Avira found a trojan and I deleted it (not sure if the two are related, but I can not think of anything else I have downloaded or installed in the past month or so).The old PC is off; the Wii is on but probably only maintains a small connection. The iPad and other laptop are not mine, but if either is on, they probably have little to no activity right now since the user is away.
View 1 Replies
View Related
Feb 22, 2012
I have a 4410N set up on my network. I'm using 4 VLANs on my network, of which, I use my default VLAN 1, as the "public" VLAN which we use to give our clients free WiFi. I would like to have two SSIDs visible from the access point, one unsecured and connected to VLAN 1, and the other secured with WPA2 and connected to our office VLAN on which various servers and resources are available. My preference is for both SSIDs to be visible, as there is not a major security issue and as the only IT person, I do not have time to configure every computer which uses the network with the SSID, but I'll do that if I have to.
I set up the 4410N with it's first SSID using our public WiFi name and did not put any security on it. I went to the VLAN page and set it to use VLAN 1 as both the default VLAN and the VLAN for the first SSID. Then I went back to the Basic Settings page and added a second SSID and chose "Enabled". I went to the Security page and left most things as default (Wireless Isolation between SSIDs is enabled) and changed the security settings for the office SSID to WPA2-Personal. Finally I went to the VLAN page and set it's VLAN to 4.
When I go back to my computer, or from other wireless devices, I only see the public SSID, not the office. I do see on my computer (Win7 x64) an "Other Network" option, but the signal strength on that network is significatnly weaker than that of the public SSID. Also, if I try to connect to it using the office SSID name and the password I set, it doesn't connect.
Am I completely misunderstanding how multiple SSIDs are supposed to work? I am working from a lot of assumptions here.
PS I have no clue if this would affect it, but in the interest of listing all possible factors, the 4410N is powered via PoE and the switch port it is connected to is set to 802.1Q with 1-4 set as the VLANs.
After posting this I discovered that in the Wireless Status page, both SSIDs are listed, but only one (the public SSID) has a MAC listed. I assume I need to add one somewhere. Where should I do this, and what's a "safe" MAC to use that won't conflict with anything?
View 3 Replies
View Related
May 6, 2011
ok so ive been messing with my aunts desktop trying to get it to run online.
her network adapter SAYS its connected but when i try to actually go online it says its not connected.
i checked the connection and it does say its connected. it is a fresh install and i reinstalled the driver for the internet.
ive unchecked the automatic config for the net options (saw in some suggestions)
View 4 Replies
View Related
Dec 25, 2011
I am having Inspiron N4010 for almost an year now. I have had many troubles with this but never with internet connectivity. Last week I saw myself not being able to be connected to internet through wireless or wired network while everybody else was connected and surfing. I just thought it to be a small problem and the problem seemed resolved that very day itself on its own.
But today this computer has simply failed to get connected. it does get connected, open a page or two and then again refuses to connect. On the problem diagnoses from network sharing center, it was showing that the websites are not responding, then it started showing that DNS server was not responding while all my setting are correctly configured. I pinged gateway and it responds but on pinging some website there is no response at all. It s a problem with my laptop only as everybody else are using internet very well. I am using internet through my WiFi enabled cell phone using the same connection and router that i use for my laptop. I need an urgent solutions as I have to meet some deadlines regarding assignments.
View 4 Replies
View Related
Aug 23, 2012
I am connected wirelessly on my laptop to my DIR-655 (D-Link) router. There is something weird going on to me in which is shows I am connected to two networks, one my home network clearly identified. The other one a "public network" listed as unidentified, all on one wireless connection. I run Windows 7 SP 1 32-bit. I would like somehow to merge or remove the second one from the listing.
View 1 Replies
View Related
Mar 24, 2011
I'm trying to get a wireless router working for friends. I got it to work yesterday, but now it is no longer working. [code] If I connect my computer to the HAG, it, of course, works fine.Yesterday, I hit the reset button on the back of the conitech router (because they didn't have the password) and went through the setup wizard, connecting my HAG to the WAN port on the router and it worked fine, both connecting via wireless and with a cable to one of the LAN ports on the router.Today it is no longer working. Both wireless and LAN show it is connected but I can't access the internet.
View 6 Replies
View Related
Nov 29, 2012
when I hover my mouse over my signal bars it says I am connected to a network named 'home-9C78' but when I click to bring up my list of available networks, it says I am connected to a network named 'Reshiram' Reshiram is the name of my network and there is NO 'home-9C78' ANYWHERE in the list!!! I don't know where my computer gets this home-9C78!!! and I NEVER ever connected to a network with that name!!! it is supposed to be 'Reshiram
View 2 Replies
View Related
Dec 25, 2011
my netbook shows it is connected, but won't open to any sites
View 1 Replies
View Related
Jul 10, 2010
There is a discussion of this going back many months in the previous forum. My initial post there has had over 600 views and I see that an IT administrator with 10 BB has the exact same problem. I have replaced my BB 4 times and all of them behaved the same way with this CISCO WAP4410N:
THE PROBLEM: The 4410 drops the WiFi connection to a Bold 9700 BB (using WAP2). I got an old Motorola about 6 years old out and found it works fine with the BB as does most of the public hot spots. This is an issue with the 4410. An IT Admin has found (an posted in the eariler forum) that for some reason the key change is not accomplished when issued by the 4410 but it works for others. The Admin discovered that if he set the timout on the key change to maximum he only has to restart the 4410s every 10 days.
So I have the 4410 for my 5 computers with which it works fine and beside it the old Motorola for the BB.
When I called support about this I was told that "we don't support connections to Blackberry." I hate to have to sell this thing on Ebay and buy another brand becuase of this. Seems that Cisco would fix it.
View 1 Replies
View Related
Mar 6, 2013
I have an EA 4500. Tonight I was trying to see what devices were connected. The window shows 0 devices connected, although about 20 devices are connected and working. When I click on "Devices Connected", I get the spinning wheel, and after multiple attempts by the application to list devices, I receive a message that the application does not work. I have the latest firmware installed. This is a recent issue. I have not made any changes to network configuration, nor to any of the devices that all have internet access. I will note that I did not set up a separate SSID for each band. But that did not seem to be an issue in previous months. I also cannot access the router ui from my windows 7 desktop. I can access the abbreviated ui through my Android phone. I tried connecting through smart wi-fi and by ip of the router. I just get the endless spinning circle of dots. I am running Windows 7 all up to date. All drivers are up to date.
View 7 Replies
View Related
Jun 17, 2012
I am trying to find out what devices are connected to my router. I have had some illegal downloading from my IP address but it has not been done from my computer. It is showing in Cisco Connect that I have 15 devices connected, I should have no more than 6 devices connected so trying to figure out who is connected on my computer.
View 9 Replies
View Related
May 8, 2012
I have a Windows 7 Laptop which has got a red X on the connectivity icon even when connected, and this since april. Now, I don't have any idea of what caused it. I have Tunngle installed, but i don't think that's the problem. I also have updated my internet drivers, but without success. In the network boards i also have a weird second wireless connection which is called "Microsoft Virtual WiFi Miniport Adapter #6"
View 5 Replies
View Related
Oct 20, 2009
I have a 3845 enabled for CDP connected to a stack of 3750 switches. From the router, i dont see any CDP neighbors. From the switch, i can see the router as neighbor. Why isn't the switch showing as a neighbor from the router side? [code]
View 3 Replies
View Related
May 21, 2011
trying to network 2 desktops running xp.
View 14 Replies
View Related
Aug 2, 2011
My Acer One Aspire wireless connection shows connected but I cant get any Firefox browser to work.
I have a D-link DIR-825 router and it has worked every time except today. I havent used my Netbook very much at home though, maybe a few times a year as I usually take it with me on trips.
I attempted to narrow down the problem. I called D-link as my router was still under warranty. They advised clearing all my old connections and rebooting but I got the same problem. I told them my Sony PS3 works, so they suggested I contact Acer as they think it is not the router. My direct hardwire connection also works.
I then took my Netbook to Best Buy and it worked there. The guy said they can pay a visit to my house as it is probably interference of some sort. This will cost $100. Why would my PS3 work if it was interference? Maybe it�s the proximity of my Netbook to something, but I tried it near my PS3 and it still had the same problem.
Id rather try to solve the problem myself first. I havent changed anything except a modem and Windows 7 updates.
View 11 Replies
View Related
Apr 21, 2011
as gone all of a sudden. Checked cables, restarted both router and PC, and even rang provider with questions.. Router seems to be working fine as laptop and iphone both got internet access with the same router. The Local area connection icon showed limited on no connectivity snd so the provider renewed the IP manually and local area connection says its connected now but there is no internet access.. They suggest it could be something to do with firewall or something else blocking it but as far as I am concerned I did not make any changes to the pc the night before when it was actually proper connected.. The desktop pc is running windows XP and I tried downloading ethernet controller driver from the web and upgrading it but it did not improve the situation.
View 17 Replies
View Related
Feb 14, 2013
am trying to connect my laptop withgalax tab via mobile AP configuration, it give me this error {dhcp is not enabled for wireless network connection}
View 1 Replies
View Related
Aug 23, 2012
I see some other threads about this same thing but I wanted to start my own to keep track if what I did. I know zilch about computers.I have an ACER I got less than a month ago. I have Verizon mifi. Windows 7My comptuer says I am connected but it says no internet access. The wifi works fine on my old netbook though. I keep getting error 105 Unable to resolve the server's DNS address. What do I do?
View 1 Replies
View Related
Aug 8, 2011
my laptop shows connected to the router however no internet; other mobile devices connect and show internet
View 1 Replies
View Related
Dec 11, 2012
I was trying to port fwd my RDP and then I ended up getting side tracted and changed my routers password [URL] it would cause my router to stop working. I know my adapter is fine, because I can connect to the internet via wired connection. My wifi DHCP is not enabled however and I have no clue on how to enable it.
Here is the settings from ipconfig/all
Microsoft Windows [Version 6.2.9200]
(c) 2012 Microsoft Corporation. All rights reserved.
C:UsersAlex>ipconfig/all
[code]...
View 2 Replies
View Related
Apr 12, 2012
Device: Cisco 3550T Catalyst ...Tested working all ports Configured Speed/Duplex both manually and set to auto with same result Problem: No connection when connected to specific Motherboard/Lan chipset that is using Realtek PCIe GBE Family controller (NIC)
Motherboard1:When connected to the 3550T the LED is amber for maybe a minute then goes off
Motherboard2:When connected to the 3550T the LED is Green but Motherboard Nic is amber.In windows under adapter settings, Local Area Connection Both Show red X
Motherboard1:
Os: Win7 Sp1 x64 w/latest updates
Mb: Gigabyte GA-P55A-UD3 v2.0
LAN: Realtek RTL8111E
Motherboard2:
Os: Win7 Sp1 x64 w/latest updates
Mb: Gigabyte x38-DQ6 v1.0
LAN: Realtek RTL8111B
The ports are only configured with
Switchport access
No other filters or access list? I have tried on multiple Cisco Switches 2950T, 3500 and 3550T with same result. what odd is these pc's can plug into a Netgear or ActionTec(Verizon) type of switch and work fine. Is there some command I need to apply to those ports to make it work with these GBE controllers. Or How do I get these Gigabyte Mobo(NiC) to work on Cisco Switches?
View 4 Replies
View Related
Jan 12, 2013
On rv110w, I have 4 vlans. vlan3 feeds a dumb switch and a Wireless AP. When looking at router DHCP leases, it shows devices connected that are not connected. Kinda like it doesn't refresh the list. Set to 50 leases. Questions: Is this normal? How often should it refresh? Is the DHCP time put in as minutes???
View 11 Replies
View Related
Nov 27, 2011
My computer (running windows XP and connected to the internet with a D Link USB adapter) refuses to load any webpages: despite showing full signal strength and connection in both the D Link settings and the windows XP wireless panel.I am able to ping websites and other computers in the house (all of which are able to access the internet) but no pages load in any browser I try.
View 1 Replies
View Related
Nov 19, 2012
My 1394 status shows connected. But the lite on my input cable is not on?
View 1 Replies
View Related
Jul 18, 2012
my neighbor is having a problem with her computer, its an HP touch smart [not sure of model] every other computer in her household works [1x wired 1x wireless].
the computer in question has had repeated problems and various hardware issues and has been sent out for repair on more than one occasion all for non software related issues, i take care of software issues and diagnose hardware problems and i have done so without a hitch until now.
when the problem first started happening i would do a system restore to a point were it was working, but that does not seem to be working anymore
i have tried disabling firewalls [she uses AVG internet security edition which is on all of her computers], windows firewall, disabling and re-enabling network drivers, updating drivers, installing different and previous versions of browsers
View 4 Replies
View Related
Feb 4, 2012
My wireless connection shoes connected but no internet access. when i connect directly to the modem to computer internet is ok. i am using linksys wrt400n route
View 17 Replies
View Related
Aug 30, 2011
Do I have a virus my when I try to get on the internet at home is wont allow me in, it keeps popping "not working at time" my wireless is good. what can i do?
View 1 Replies
View Related
Mar 27, 2011
I have a Dell Vostro 1500 and I have AT&T wireless internet in my house. My other computers and Roku connect with no problem, but mine even though it says it is connected, is not connected. I have Windows XP the other computer is Vista and the desktop is also XP. Even AT&T came over the house and said something is wrong with the computer.
View 12 Replies
View Related
Dec 30, 2012
I have been using Dell Vostro-1320 laptop with Windows XP. It was running good. Recently I have installed the McAfee Internet Security software. But now I do not have internet access through this laptop although the network icon shows "connected". I have tried all the advice/solutions for such type of problem by doing Firewall off/on and changing adapter & network setting. I also updated all the drivers. But nothing works. It is notable that my other desktop is working properly in spite of installing this software.
View 4 Replies
View Related
Dec 13, 2011
When I have both 2,4 and 5,0 GHz band enabled on the E4200 router my PC (WMP600N-PCI adapter) has max. 130Mbps.When I enable only the 5,0 GHz band it has a speed of 270Mbps.The same speed issue with my Dell laptop.Router and PCI adapter are new (3 days old) and both have the latest firmware.Both PC and laptop are running on W7.how to increase the speed with both bands enabled?
View 6 Replies
View Related
Jan 19, 2012
We have a 4410N that all the time drops the connetion. We have approx 25-30 users using wireless. But when they try to connect or are connected, the router drops the connection like a yo-yo. The firmware is updated with no difference.
The wireless connection is very unstable. It's configured with WPA2 Personal and is connected through a POE-switch with IPv4. The logs don't answer the questions why it drops the connection.
View 9 Replies
View Related
Feb 9, 2011
after reading the many issues reported here about the WET200's WPA abilities (or lack thereof), I doubt that there will be an easy solution to the issue I'm having, but it's worth a try.The setup consists of a WET200 that should bridge two devices in a remote room to our main network. The AP is a WAP4410N, which works beautifully with all other connected devices. The WAP4410N is set up in 'WPA2-Personal Mixed' mode, and only b/g (as n was giving other, unrelated trouble). The WET200 sees the network just fine, is able to connect and receives an IP from the DHCP server. The devices behind the bridge also have connectivity - all well so far. However, at a certain point in time, which i _believe_ to coincide with the key renewal on the AP, the bridge loses the connection to the AP, even though it reports its WLAN status on the web interface (via LAN) as connected. The AP's log shows the following (MAC address is the WLAN interface on the WET200).
View 2 Replies
View Related