i set up the WAP4410N and it can be connected with our router. But it's not protected by our password, but once i have set the password of WAP4410N by changing the security mode to WEP, now i will prompted to password when I connect the AP, but it shows limited connectivity, I can't even access my local LAN resources at all.
View 2 Replies
If you have two wireless routers on the same private network. On configuring the second router's password and SSID I know the second wireless routers DHCP must be turned off.Can you explain step by step on configuring the second wireless. Must the second wireless be connected to the internet. If yes, how? Must I take the first wireless router off the modem and connect it to the second wireless router for internet connection. (Problem with that is connection from the ISP)
View 2 Replies View RelatedI can't configure the SSID more than one in the web UI of the WAP4410N. Except I can type the first SSID1, the rest SSID2 - 4 are grey which not allow me to type in anything. ( See attached the screen shot ) My current version is 2.02.1 and I was using IE8 under windows 7.
View 3 Replies View RelatedI have a 4410N set up on my network. I'm using 4 VLANs on my network, of which, I use my default VLAN 1, as the "public" VLAN which we use to give our clients free WiFi. I would like to have two SSIDs visible from the access point, one unsecured and connected to VLAN 1, and the other secured with WPA2 and connected to our office VLAN on which various servers and resources are available. My preference is for both SSIDs to be visible, as there is not a major security issue and as the only IT person, I do not have time to configure every computer which uses the network with the SSID, but I'll do that if I have to.
I set up the 4410N with it's first SSID using our public WiFi name and did not put any security on it. I went to the VLAN page and set it to use VLAN 1 as both the default VLAN and the VLAN for the first SSID. Then I went back to the Basic Settings page and added a second SSID and chose "Enabled". I went to the Security page and left most things as default (Wireless Isolation between SSIDs is enabled) and changed the security settings for the office SSID to WPA2-Personal. Finally I went to the VLAN page and set it's VLAN to 4.
When I go back to my computer, or from other wireless devices, I only see the public SSID, not the office. I do see on my computer (Win7 x64) an "Other Network" option, but the signal strength on that network is significatnly weaker than that of the public SSID. Also, if I try to connect to it using the office SSID name and the password I set, it doesn't connect.
Am I completely misunderstanding how multiple SSIDs are supposed to work? I am working from a lot of assumptions here.
PS I have no clue if this would affect it, but in the interest of listing all possible factors, the 4410N is powered via PoE and the switch port it is connected to is set to 802.1Q with 1-4 set as the VLANs.
After posting this I discovered that in the Wireless Status page, both SSIDs are listed, but only one (the public SSID) has a MAC listed. I assume I need to add one somewhere. Where should I do this, and what's a "safe" MAC to use that won't conflict with anything?
Looking to setup 3-4 WAP4410N AP's but only want to use 1 SSID and one set of keys if possible.
View 15 Replies View RelatedI have a wap4410n acting as AP and a second wap4410n acting as wds repeater.
I've only managed to get the wds repeater to work when it has a different ssid to that of the ap - I'd like the wds repeater to have the same ssid as the ap, should things work in this configuration?
We just got a WAP4410n and cant seem to get multiple SSID's to show up when searching for them.Only SSID1 shows up in Kismet or any other type of Wifi detector software, is it supposed to be like this?I would imagine that it should display both SSID's
-Mynetwork1
-Mynetwork2
Instead of just Mynetwork1, I have tried everything i can think of to connect to the second one but nothing seems to work.
I have a WAP4410n which has been configured with a single SSID since implementation several weeks ago with no issues. I am now trying to add a second SSID and not having any success. Originally the second SSID was not being assigned a MAC address and thus not being broadcasted. After upgrading firmware to 2.0.4.2 I now see a MAC address associated with second SSID and it is being seen by clients, but they still cannot connect. I reset the AP to default settings and reconfigured from scratch but still no luck. I have two of these APs, the other one is still at FW rev 2.0.1.0 and has same issue (it does have MAC address associated with second SSID so I didn't bother upgrading firmware yet).
I have tried a few different authetication options, including disabling authentication, to no avail. Question - I do not see an IP address associated with the second SSID - is that the problem and if so, how do I fix that?
I am trying to use some WAP4410N in client mode, not much luck.In one case they shouldt connect to different unsecured networks controlled by a Cisco 5508 controller.I can get connection to one of the SSID's but not very stable.One ssid can be seen if i switch from ap-mode to client and run a sitesurvey. If i after that run a site survey again the ssid is not shown.Cant get connected. A third ssid acts "normal" but the 4410 never connects.I have a forth case, WPA2 Personal, cant connect.Been trying fw 2.0.3.3 still no succesAre client mode not usefull at all ?
View 6 Replies View RelatedI have come across a new problem with our WAP4410N. I have set up multiple SSID's for various groups of people and guests at our company, the first and main SSID has set security properly at WPA2-Personal with a 63 character password. So I went ahead and setup the other 3 SSID's with the same security (just to initially get security going was planning on taking down one of them for guest account), but when I boot up my testing laptop, it shows that SSID's 2-4 have no security what-so-ever.
I have re-checked my settings in the Wireless Security tab and they are all still set with the passwords.
I am using: PID VID: WAP4410N-A V02Software Version: 2.0.4.2.
Currently I have a WAP4410N setup and would like to add a second WAP4410N but as wireless repeater. I want my users to have wireless access without the need to keep changing the wireless connection based on their location within the factory.
The AP Mode on teh WAP4410N gives me the options below, but I am not sure which one is the correct one:
Option 1 - Wireless WDS Repeater
Option 2 - Wireless Client/Repeater
Below is the link from cisco with explanation. [URL]
Also, if have WAP54G, can I setup this unit to be a wireless repeater with the WAP4410N devices? or all repeaters must be of the same model? Existing WAP4410 is setup to operate at Wireless B/G Mixed mode.
I need setting up a WAP4410n v 2.0.1.0 as a repeater. Warning, this is the first time I have worked with a repeater. I have tested with a netgear router and a Linksys 160n router. Unfortunately I only have the netgear to continue testing with since the Linksys is at my customer’s site. I can get my hands on a Linksys E3200 if I have to. I have tried a number of setting combinations and I still cannot get the signal to be repeated. So this is what I think the setup should be:I setup the router and the WAP4410n repeater to have the same ssid and channel. For security I first tried to have both the router and the repeater to use WPA2 personal using TKIP then I read that there is a problem using WPA2 with version 2 of the firmware so I then tried using WEP having both the router and repeater using the same key. I selected Wireless WDS repeater mode. I did a site survey and selected my router. Now from what I understand, which is very little, this is all I should really need to do. I have left all of the other settings to the default values. So what am I missing?
View 1 Replies View RelatedSetting up a WAP4410n v 2.0.1.0 as a repeater. Warning, this is the first time I have worked with a repeater. I have tested with a netgear router and a Linksys 160n router. Unfortunately I only have the netgear to continue testing with since the Linksys is at my customer's site. I can get my hands on a Linksys E3200 if I have to. I have tried a number of setting combinations and I still cannot get the signal to be repeated. So this is what I think the setup should be: I setup the router and the WAP4410n repeater to have the same ssid and channel. For security I first tried to have both the router and the repeater to use WPA2 personal using TKIP then I read that there is a problem using WPA2 with version 2 of the firmware so I then tried using WEP having both the router and repeater using the same key. I selected Wireless WDS repeater mode. I did a site survey and selected my router. Now from what I understand, which is very little, this is all I should really need to do. I have left all of the other settings to the default values.
View 2 Replies View RelatedIs there a recommended configuration for setting up a wap4410n as an ap?
The reason I ask is that I have an rvs4000 with a wap4410n as ap and a second wap4410n as wds repeater and it seem I have to reboot one or more of them every couple of days due to various users being unable to connect wirelessly or being able to connect wirelessly, but with no Internet access.
Starting with a reboot to facory default, the rvs4000 gave the wap4410n ap an address of 192.168.1.101 so I just left things like that. Similarly, the wap4410n wds repeater was given an address of 192.168.1.103, which I did not change.
Given there seems to be some kind of intermittent problem, would it be better to have the rvs4000 reserve an ip address for the two wap4410n? Note that I did try this, but after adding the two reserved ip addresses (192.168.1.101/103) and clicking on "save", the rvs4000 rebooted and came back up without the two reserved addresses...
I have a WAP4410N and would like to turn down the power output below 100%.
It has a very strong signal, and is covering our small office and half the parking lot.
In the Administration Guide, under FAQs, it mentions a setting for output power but I cannot find this setting.
The SW version is 2.0.0.5, and that seems to be the latest version - the file I downloaded is WAP4410N-fw-2.0.0.5-K9.img but I haven't installed it yet.
I need to configure WAP4410N wireless access point for our company guest and visitors.i need them to only surf internet and not to go to LAN (servers).I think i need to create VLAN for this ? can any one tell me setting for configure only to surf internet thru WAP4410N ?
View 1 Replies View RelatedMy question is if I can configure 3 ssid, for 3 different VLAN and add the DHCP address from a WAP4410N AP, when you upgrade to the latest version of IOS I can have this functionality?
View 2 Replies View RelatedWe are trying to setup a WAP4410N with 2 SSID's. One SSID for our private network and the other for guest internet access. On the VLAN and QoS page there is a setting for priority. What would be the suggested values for this setting? We obviously want our private network to receive priority over our guest network.Also, does VLAN Tag setting need to be on Tagged to determine private from guest traffic?
View 2 Replies View RelatedRecently I have purchased two brand new wap4410n access points.
I have connected my computer directly to one of the access points, and attempted to connect to the Web Configuration utility through my web browser.
I'm using a: 09' MacBook Pro, running Snow Leopard and Safari 5.
I can access the login screen of the access point, although when I enter the default username: admin and password admin, the login screen returns an error: Invalid username and/or password (or something to that effect). The URL changes to: http://192.168.1.245/login.htm&no=3.
I have reset the device by holding in the reset button for thirty seconds, powered down, powered up and re-attempted to login.
I still get the same error as above.
I have attempted to access the Web Configuration utility on both access points, and both access points provide the same error. I have also tried using the username: cisco and password: cisco.
Cisco, when contacted, said both access points must be faulty and I should replace them.
The probability of such an occurrence happening with two devices seems very low, and leads me to think there must be other factors at play. The only constant I can think of is the fact I'm using the same computer to access the devices.
I am setting up a guest WLAN network on our existing 1242 AP's using a seperate VLAN. On most wireless devices which are on the company network/VLAN's, I have used WEP authentication with hex keys, and no broadcast. Obviously this cannot be the same for a guest internet connection.We want to have the VLAN/SSID in guest mode (which i have configured) for broadcasting, and then once someone selects the SSID on their laptop or smart phone, they are just prompted to authenticate with a standard alphanumeric password (example "guestwifi") instead of a 40 or 128 bit key.
I have searched all over and tried multiple things in the CLI on AP1, but can't seem to get anywhere.
I just purchased an E4200 and got it up & running. Everything was fine, until I connected a Wi-Fi DVD player to it. I followed the DVD player procedure, which was to push the WPS button on the router, and then the appropriate button on the DVD player. After a few seconds, the player connected, and I successfully accessed YouTube through it.
So far, so good -- except that it turns out that the router, on its own, changed the SSID and password. When I could not get Wi-Fi access on my iPhone, I checked the Wi-Fi settings, and instead of the original SSID of the E4200 -- let's say ShadeTree -- it was changed to Cisco_WPS_xxxxx (the X's represent numbers). I started Cisco Connect, and a screen came up showing that the password had been changed from the original, and listed both the original and new passwords.
What is going on? Why would the E4200 change the SSID and password all by itself, when I connected a Wi-Fi equipped DVD player with WPS? Is this going to happen when I connect a Wi-Fi equipped TV set, or some other component? What can I do to keep the E4200 from changing the network name and password all by itself? Or am I going to have to re-program every other Wi-Fi device (iPad, iPhone, etc.) every time I add a new component?
Where do I find the router SSDI and password. I am trying to reinstall Linksys E1200
View 2 Replies View RelatedI purchased what I think is a new EA4500 but the box was not sealed. On setup it had a SSID name of Mischief Dolphin populated with a random password. Is this a default or was perhaps this router already setup (used)
View 2 Replies View RelatedI have AP1 setup with WPA2-Enterprise. How would I setup AP2 (WAP4410N) to be a repeater for AP1?
View 1 Replies View RelatedI had to default my wireless router " Netgear WGR14V6" and since then I haven't been able to connect with my wireless card. I can physically connect to it with a cable but I can't access it with the wireless card. When I look at the properties it says that it is working fine but I can't seem to find where to change the "SSID and the security phrase". Usually when it is up and running it has a status button and when you click on it there is a tab that you click on and it shows you the SSID and the rest, but now since it is not connected there isn't anything that I can find to change this.
View 1 Replies View RelatedThe EA4500 web-settings application asks for a username and password. The username is "admin" and the password is my long (60 character) wpa key. I see where I can change the password but it says I'll lose all wireless connections. This doesn't make sense to me. I would think the router administration username and password are completely separate from the ssid and wpa key. This was the case with my earlier LinkSys router. I'd like a router administration username to be something other than the generic "admin" and a password that is easier than my long wpa key. I want a separate ssid and wpa key (what I currently have).
View 2 Replies View RelatedRecently, I bought the E3200, and tried to configure its ports for gaming. Yet, whenever I would hit save settings, it would say my settings were saved, then return me to the settings page. But the settings would be blank. I tried downloading firmware from the website (which should say September 28), yet it still says I am running the firmware from September 1st, even after I applied the upgrade and followed through with the 50 second reboot process.
So, I guess my final question for any tech savvy person out there is "What is wrong with my router/firmware?" I am running the browser config in the most recent Firefox on the same MacBook I used to install the router, and haven't changed any settings other than the SSID and password.
Im having problems with setting up my cisco WAP4410N as a repeater to extend the signal of cisco E2500.It works fine when there is no password to be set on both devices. But when either one of these devices had beenset a password on it, then WAP4410N failed to extend the signal of E2500.
I tried steps as below:
1. Same password type in WAP4410N and E2500.
2. Different password type in WAP4410N and E2500.
3. Set password in WAP4410N ONLY.
4. Set password in E2500 ONLY.
All steps above makes WAP4410N fail to extend the signal range of E2500. WAP4410N successfully works as a repeater to extend the signal of E2500 when there is no password to be set on both devices.
what the ssid password is netgear 600
View 3 Replies View RelatedI have the following equipment:
Cisco 871W router
2x WAP 4410N APs running 2.0.3.3
I currently have 1 AP connected to the router via copper. The AP to AP link is over 802.11. I have attached a diagram reflecting the current topology.
The AP-to-AP link will come up utilizing B/G/N mixed mode; however, the connection is basically unusable. About 30% of the traffic is dropped, while the packets that do make it have a consistently volatile latency, anywhere from 15 to 1500 ms. I have had success using G-only and B/G mixed. The link is stable (I have had the best results with B/G). The problem is, I didn't buy the 2nd 4410N to run the G protocol. I would like to connect the APs running either B/G/N (hopefully negotiating to N) or N only. I am wondering if there is a certain configuration I can utilize (perhaps using WDS repeater or bridge versus Wireless Client/Repeater?), or a firmware upgrade set for release that can make this happen for me.
Been a while since I have conf'd a controller. I believe its WLAN/edit/security/layer2 and below psk format edit the password?
View 2 Replies View RelatedIn the past couple of years, I've picked up a couple of Linksys WRT54G routers for a buck or two at flea markets. I hadn't thought about the fact that no assigned SSID or Password came with them. I downloaded the Linksys set-up files from their website and recently set up both of them for relatives. They work great but they are "unsecured networks". I'd like to change that.
View 2 Replies View RelatedI have a new laptop and had a dlink DIR601 installed on an older laptop. I wasn't the one who got it set up originally but they did have me write down my SSID, password and security key. The dlink came with a cd but there is no cd rom on this laptop. I have tried reset, on line download (which only let me do the revisions). I have talked to a few people and they say it's easy!
View 1 Replies View Related
