Cisco Wireless :: WAP4410N Can Get Connection To One Of SSID's But Not Very Stable
Jan 18, 2011
I am trying to use some WAP4410N in client mode, not much luck.In one case they shouldt connect to different unsecured networks controlled by a Cisco 5508 controller.I can get connection to one of the SSID's but not very stable.One ssid can be seen if i switch from ap-mode to client and run a sitesurvey. If i after that run a site survey again the ssid is not shown.Cant get connected. A third ssid acts "normal" but the 4410 never connects.I have a forth case, WPA2 Personal, cant connect.Been trying fw 2.0.3.3 still no succesAre client mode not usefull at all ?
View 6 Replies
ADVERTISEMENT
Oct 12, 2011
I can't configure the SSID more than one in the web UI of the WAP4410N. Except I can type the first SSID1, the rest SSID2 - 4 are grey which not allow me to type in anything. ( See attached the screen shot ) My current version is 2.02.1 and I was using IE8 under windows 7.
View 3 Replies
View Related
Feb 22, 2012
I have a 4410N set up on my network. I'm using 4 VLANs on my network, of which, I use my default VLAN 1, as the "public" VLAN which we use to give our clients free WiFi. I would like to have two SSIDs visible from the access point, one unsecured and connected to VLAN 1, and the other secured with WPA2 and connected to our office VLAN on which various servers and resources are available. My preference is for both SSIDs to be visible, as there is not a major security issue and as the only IT person, I do not have time to configure every computer which uses the network with the SSID, but I'll do that if I have to.
I set up the 4410N with it's first SSID using our public WiFi name and did not put any security on it. I went to the VLAN page and set it to use VLAN 1 as both the default VLAN and the VLAN for the first SSID. Then I went back to the Basic Settings page and added a second SSID and chose "Enabled". I went to the Security page and left most things as default (Wireless Isolation between SSIDs is enabled) and changed the security settings for the office SSID to WPA2-Personal. Finally I went to the VLAN page and set it's VLAN to 4.
When I go back to my computer, or from other wireless devices, I only see the public SSID, not the office. I do see on my computer (Win7 x64) an "Other Network" option, but the signal strength on that network is significatnly weaker than that of the public SSID. Also, if I try to connect to it using the office SSID name and the password I set, it doesn't connect.
Am I completely misunderstanding how multiple SSIDs are supposed to work? I am working from a lot of assumptions here.
PS I have no clue if this would affect it, but in the interest of listing all possible factors, the 4410N is powered via PoE and the switch port it is connected to is set to 802.1Q with 1-4 set as the VLANs.
After posting this I discovered that in the Wireless Status page, both SSIDs are listed, but only one (the public SSID) has a MAC listed. I assume I need to add one somewhere. Where should I do this, and what's a "safe" MAC to use that won't conflict with anything?
View 3 Replies
View Related
Sep 8, 2009
Looking to setup 3-4 WAP4410N AP's but only want to use 1 SSID and one set of keys if possible.
View 15 Replies
View Related
Nov 14, 2010
I have a wap4410n acting as AP and a second wap4410n acting as wds repeater.
I've only managed to get the wds repeater to work when it has a different ssid to that of the ap - I'd like the wds repeater to have the same ssid as the ap, should things work in this configuration?
View 21 Replies
View Related
Jun 2, 2010
We just got a WAP4410n and cant seem to get multiple SSID's to show up when searching for them.Only SSID1 shows up in Kismet or any other type of Wifi detector software, is it supposed to be like this?I would imagine that it should display both SSID's
-Mynetwork1
-Mynetwork2
Instead of just Mynetwork1, I have tried everything i can think of to connect to the second one but nothing seems to work.
View 40 Replies
View Related
Nov 15, 2011
I have a WAP4410n which has been configured with a single SSID since implementation several weeks ago with no issues. I am now trying to add a second SSID and not having any success. Originally the second SSID was not being assigned a MAC address and thus not being broadcasted. After upgrading firmware to 2.0.4.2 I now see a MAC address associated with second SSID and it is being seen by clients, but they still cannot connect. I reset the AP to default settings and reconfigured from scratch but still no luck. I have two of these APs, the other one is still at FW rev 2.0.1.0 and has same issue (it does have MAC address associated with second SSID so I didn't bother upgrading firmware yet).
I have tried a few different authetication options, including disabling authentication, to no avail. Question - I do not see an IP address associated with the second SSID - is that the problem and if so, how do I fix that?
View 1 Replies
View Related
Jul 3, 2011
i set up the WAP4410N and it can be connected with our router. But it's not protected by our password, but once i have set the password of WAP4410N by changing the security mode to WEP, now i will prompted to password when I connect the AP, but it shows limited connectivity, I can't even access my local LAN resources at all.
View 2 Replies
View Related
Sep 26, 2011
I have come across a new problem with our WAP4410N. I have set up multiple SSID's for various groups of people and guests at our company, the first and main SSID has set security properly at WPA2-Personal with a 63 character password. So I went ahead and setup the other 3 SSID's with the same security (just to initially get security going was planning on taking down one of them for guest account), but when I boot up my testing laptop, it shows that SSID's 2-4 have no security what-so-ever.
I have re-checked my settings in the Wireless Security tab and they are all still set with the passwords.
I am using: PID VID: WAP4410N-A V02Software Version: 2.0.4.2.
View 1 Replies
View Related
Nov 24, 2009
I recently purchased the WRT-120N router for my home network. The wireless is set to mixed mode, with WPA Personal encryption, with key renewal set at the default 3600 seconds. My problem is that the connection is not stable. I can be connected with one computer, then, as soon as another computer joins the network, I get kicked off. This happens with all of my 5 computers. In addition to this, several of my computers will not automatically connect to my network after the computer is restarted. When I try to reconect manually, it says the network is unavailable. The only way I can get back on is if I go into "Control PanelManage Wireless Networks" and delete the setting for my network, then connect again through the "Connect to a network" window.4 of my computers are running Windows Vista with a minimum of Service Pack 1. The Other is running XP with Service Pack 2.
View 9 Replies
View Related
Nov 23, 2011
I got an WRT160N,when I had 5mb connection it was working normal,but since I changed to 10mb,it downloads at 40kbp-100kbp,The connection is very stable,but the speed its very slow.I try to download the firmware but its with .bin extension and I don't know how to open it.
View 9 Replies
View Related
Sep 18, 2012
My question is if I can configure 3 ssid, for 3 different VLAN and add the DHCP address from a WAP4410N AP, when you upgrade to the latest version of IOS I can have this functionality?
View 2 Replies
View Related
Aug 9, 2011
i wanted to know the reason of why my ping drops or how to make it more stable. For example i play a game called League Of Legions, which i think my connection and pc exceeds the system requirements. (Except my Video card since im using a standard which was with the MOBO.)
When im playing this game, i have a ping of 50-80, suddenly it drops to 300-500, which causes me lag (Happens multiple times in a 45min game or any). I think thats not normal, since other players dont suffer from that.
[url]....
View 6 Replies
View Related
Nov 16, 2011
I am having some difficulties to have a stable connection on a Cisco 881. I have a IP Sla running with an ICMP-ECHO towards the uplink router. Linked with this is a tracking on the IP SLA so I can shutdown an HRSP instance with the tracking. The desired result is with this that when the nexthop becomes unavailable HSRP switches to the second router with the backup connection.
Regardless whatever timeout or threshold, the tracking switches at a random point when the line is somewhat congested. Debugging it shows me only a time-out on the IP SLA.
Is there anything possible to get the icmp-echo to retry it 2-3 times or so before going it's status is set to failure? [code]
View 2 Replies
View Related
Sep 17, 2011
About two weeks ago, my internet connection became faster. I am not sure if it has to do with my cable ISP doing something or something I did with my computer.
Right around the same time, my connection began disconnecting every two or three days. Before this, I had a rock solid connection for two years.
It will usually reconnect after a minute. Otherwise, when I boot my computer, the problem is solved.
I am certain there is a correlation between the connection speed going up and my connection becoming less stable.
View 6 Replies
View Related
Jan 19, 2012
We have a 4410N that all the time drops the connetion. We have approx 25-30 users using wireless. But when they try to connect or are connected, the router drops the connection like a yo-yo. The firmware is updated with no difference.
The wireless connection is very unstable. It's configured with WPA2 Personal and is connected through a POE-switch with IPv4. The logs don't answer the questions why it drops the connection.
View 9 Replies
View Related
Feb 9, 2011
after reading the many issues reported here about the WET200's WPA abilities (or lack thereof), I doubt that there will be an easy solution to the issue I'm having, but it's worth a try.The setup consists of a WET200 that should bridge two devices in a remote room to our main network. The AP is a WAP4410N, which works beautifully with all other connected devices. The WAP4410N is set up in 'WPA2-Personal Mixed' mode, and only b/g (as n was giving other, unrelated trouble). The WET200 sees the network just fine, is able to connect and receives an IP from the DHCP server. The devices behind the bridge also have connectivity - all well so far. However, at a certain point in time, which i _believe_ to coincide with the key renewal on the AP, the bridge loses the connection to the AP, even though it reports its WLAN status on the web interface (via LAN) as connected. The AP's log shows the following (MAC address is the WLAN interface on the WET200).
View 2 Replies
View Related
May 13, 2012
In a bit of a pickle and not sure which way to turn as I think I have exhausted all possibilities.We currently have 2 Cisco WAP4410n wireless access points running within our network. They are both on version 2.0.4.2 firmware and both on a static ip address within our infrastructure and are not working.
View 2 Replies
View Related
Apr 10, 2013
Every single one of the WAP4410N units at every single client where they've been deployed is dropping the network connection.
After an undetermined amount of time, wireless devices connected to a WAP4410N begin to lose their network connection, but each will maintain their wireless connection to the WAP. The network connection will not be restored until the WAP is rebooted. It appears the affected devices are unable to obtain/renew their IP address at the time when they lose network connection. We reduced the DHCP lease time to 2 hours, and we had no problems for 2 weeks. We then changed the DHCP lease backup to 3 days and the problem returned.
This happens with one or two SSIDs in use, with or without VLANs, always in bridge mode.
Cisco support advised us that this is a known problem that was supposed to be corrected in the 2.0.4.2 firmware revision. They have found that it does work in approximately 90% of the updates from 2.0.3.3, but is still not working for some customers. It was supposed to be fixed with firmware version 2.0.6.1 (which we've tried) but no luck.
Besides the obvious "short DHCP lease" workaround, any better ideas? Is the WAP4410N a lemon?
View 3 Replies
View Related
Apr 20, 2013
I have installed a wired and wireless connection for a compound which is around150 squire meters. I used the Cisco wap4410n routers for the wireless setup.
The structure is like this.There is a connection coming from the service provider. There is a central switch where the connection coming from service provider, the server, one Cisco wap4410n router and other two switches are directly connected to it. Again I connected other switches to the switches getting connection from the central switch. I used Cat 5e and Cat 6 cables to connect the switches as well as the wireless routers (For more info , the cable goes underground) and I used cross-over cable to connect switch to switch and straight-through to connect routers to switches. I connected the other Cisco wap4410n routers to the switches outside( I get like 6 Cisco wap4410n routers)The wireless routers are connected to the switches which are connected to the central switch and also on the other switches.
The routers are configured to have their default AP mode.My problem The connection is very slow. The connection is down almost every week and it needs to be re-configured. The connection nice on the router which is directly connected to the central switch(but not the same on the others routers which are connected to the other switches)even when I reset them they don't fall to .245 ( which is ok I can see them on the DHCP server but I still see it as problem)when I set them as a wireless wireless repeater, full signal but no connection(given that I have set same SSID, enabled allow wireless signal to be repeated, filling MAC addresses) Down here I have tried to show the architecture diagrammatically.
View 2 Replies
View Related
Sep 7, 2011
We've had this AP for just over a year and just recently it started dropping its wireless connection. To fix, I have to and unplug the power and then plug it back in.. Then it works again for a few hours and drops out again. If I navigate to the config page right after it drops, all of the settings seem to be completely gone. But if I go through and unplug/plug it in again, all of the settings are back.
I updated the firmware to 2.0.4.2, but that didn't seem to resolve the problem. Is this thing a brick now?
View 7 Replies
View Related
Mar 30, 2011
I just started a new job and recently got my CCNA and CCDA. I hop into this new job and no one knew information to the networking. They decided to re-ip the site and they had 3 wireless access points. I had to hard reset and re-configured the WAP. All the laptop in the building have reception and can get internet. If i connect anyone cell phone, wii or tablets to the wifi, it does not connect.
View 3 Replies
View Related
Apr 30, 2011
I have the following equipment:
Cisco 871W router
2x WAP 4410N APs running 2.0.3.3
I currently have 1 AP connected to the router via copper. The AP to AP link is over 802.11. I have attached a diagram reflecting the current topology.
The AP-to-AP link will come up utilizing B/G/N mixed mode; however, the connection is basically unusable. About 30% of the traffic is dropped, while the packets that do make it have a consistently volatile latency, anywhere from 15 to 1500 ms. I have had success using G-only and B/G mixed. The link is stable (I have had the best results with B/G). The problem is, I didn't buy the 2nd 4410N to run the G protocol. I would like to connect the APs running either B/G/N (hopefully negotiating to N) or N only. I am wondering if there is a certain configuration I can utilize (perhaps using WDS repeater or bridge versus Wireless Client/Repeater?), or a firmware upgrade set for release that can make this happen for me.
View 1 Replies
View Related
Sep 17, 2012
We have three WAP4410N that loses the connection. We've updated the firmware, changed the equipment, repeatedly reconfigured, but the problem persists.Is used the firmware 2.0.5.3 with WPA2 Enterprise Mixed authentication.
View 5 Replies
View Related
Dec 13, 2012
I have been using WAP4401N for almost a year in our office and I’m very happy of this device, never had any problem. So I bought 3 new ones for our customer which supposed to work in configuration below:
Network ----- AP1 –Bridge mode ----- AP2 – Bridge mode -----AP3 – Access Point mode.
Everything was working perfectly fine to the moment than bridge was broken. I can get access to all AP (obviously when connected to proper part of network) however not able to ping from AP2 -> AP1 or opposite so basically no link between AP1 and AP2. After reboot everything is working fine to next time (happens twice in two days). When I go to System Performance can see Connection is enabled but doesn’t work.
I upgraded firmware to latest version (2.0.5.3) but haven’t worked. When I’ve done some research found many users having similar problem with this device and basically they recommend to don’t buy. Unfortunately this is not an option for me as I’ve already purchased them.
View 6 Replies
View Related
May 9, 2012
My WAP4410N is configured with 4 seperate SSIDs. Two of the SSID status are showing "Enabled". The other 2 are shown as "Connected". The one that are showing as Enabled are not receiving any packets. Devices connected to the SSID that shows "Enabled" are unable to connect to the network. Any one else encountered similar issues before? This issue just surfaced few hours ago. The device has been using for around 2-3 years with minimal issues.
View 1 Replies
View Related
Aug 22, 2011
We have 4x WAP4410N access points 1 AP & 3 Repeaters, this works perfect. The situation at the moment is that the internet connection is plugged in with a cable on the AP but the question is that if it's possible to plug the internet connection into one of the repeaters?
After that are we still able to use the internet over al four access points?
View 1 Replies
View Related
Jan 2, 2012
we have a WLC 4404, Software Version 4.2.61.0 and the following Problem. The WLC worked for many years with the SSID "SKHGR". In addition to the existing SSID I have a second SSID "SKHGR-M" is created. The configuration of the two SSID's is identical.
The problem is: when I activate the second SSID, the AP losing connection with the WLC. In the log appears"AP disassociated. ... Base Radio" and "
"not advertising ssid due to radio policy". The AP's connect with the WLC, lose after few seconds the contact.
View 3 Replies
View Related
Mar 11, 2011
how to block a dynamic wireless IP address or the SSID of a wireless connection from accessing my router?
I have 2 people that have somehow managed to get access and i wish to discard them so they cannot reconnect. My wireless router is a Netgear WPN824 and i am running Windows XP.
View 3 Replies
View Related
Aug 15, 2011
So My ssid is naular and it has password protection. However there is another ssid from my router called "linksys" which is unprotected. I tried to change it and messed it up bad. Everyime I sign on to "naular" it makes "Naular 2" then Naular 2 3 then Naular 2 3 4 etc. Then I only get local access. I look at my wireless thing and it says i'm connected to naular 2 3 4 5 when I signed onto Naular earlier.
View 1 Replies
View Related
Feb 3, 2011
it's across 3 floors and the current setup is a single wireless router DIR655 (1st floor), but the WiFi suffers greatly on the floor below/above.
I have sourced 3x D link switches and 2x more DIR655's and would like to have all machines/consoles/phones etc in the household on the same network. Is it possible to keep one DIR655 as the main wireless connection and have the other as pure AP's as well as keeping the same SSID?
View 1 Replies
View Related
May 28, 2012
i have a linsys wrt54g router. my main computer is connected (wired) and works fine. until today my wireless devices were able to connect and access the internet using the router. now the ssid does not show as a possible network connection. i have unplugged everything, rest the router, checked setting, shutdown and reset every computer and all my wireless devices still cant locate the network connection???
View 9 Replies
View Related
Jul 8, 2011
i bought a WRT160N router
I connected the Router to the modem, and all the wired connected PCs were working perfectly.But then, i went to the setup page to configure the Wireless settings, and as soon I changed the SSID name, the connection internet connection droppedThe only way i had to fix this was by making a Hard Reset.after that, I also tryed changing values and settings from all the configuration tabs, and the wired connection was working properly, but as soon i changed any value from the Wireless tab, the internet connection dropped (even, in the diagnostics section, i could not do a ping to google. It says unknown host).
View 3 Replies
View Related
