I just started a new job and recently got my CCNA and CCDA. I hop into this new job and no one knew information to the networking. They decided to re-ip the site and they had 3 wireless access points. I had to hard reset and re-configured the WAP. All the laptop in the building have reception and can get internet. If i connect anyone cell phone, wii or tablets to the wifi, it does not connect.
View 3 Replies
My WAP4410N AP is running version 2.0.2.1 firmware which is quite old. There are newer firmware releases available which I'd like to upgrade to (fix the known bugs, etc.).
So I upgrade my firmware from version 2.0.2.1 to any of the following versions:
- 2.0.3.3
- 2.0.4.2
- 2.0.5.3
The AP reboots and my settings are all still there.
I go to change any of the settings I have - DNS, Time Zone, PSK, any field which can be edited and click Save.
The Save takes place and the screen refreshes to the old settings - the new settings don't stay in place after the Save.
I've also factory defaulted the AP prior to the upgrade, upgraded and then been in the same place unable to save any changed settings.
System details:
Information PID VID: WAP4410N-E V02
Device: WAP4410N Wireless-N Access Point with Power Over Ethernet Software Version: 2.0.2.1
I recently installed a WAP4410N for a customer without any problem, but a few days later I received a call requesting assistance as the customer could not login to the web admin page.
The login screen was showing, but it wasn't acceptingthe username and password that I had set. Today I visited customer to investigate.
I discovered that I could login without any problem using my Windows laptop, but that customer could not use any of their Apple MACs to login.
Apart from one Windows PC, all customer computers were Apple OS. Customer could login using their Windows PC without any problem.
I brought one WAP4410N Wireless-N Access Point and successfully configured with out fail as suggested on getting started and I am able to access internet but unfortunately I am unable to access our local servers and services which in LAN (mail-postfix, chat-spark) like.
View 1 Replies View RelatedI recently bought and installed a WAP4410N access point (using PoE) and it's running stable. I was able to access the web-based configuration by using the IP address of the AP (something like 192.168.0.184, coming from the DHCP of my router). However, I'm unable to access the web-based configuration using the host name of the device (mentioned next to the device name in the basic setup section of the web-based configuration). I changed the host name several times, but I can't connect to the device using the host name. Accessing the device by its IP address works, but I have to check the logging of my router to find out which IP address I have to use. Is there a way to access the device using the host name?
(I think my WAP4410N has firmware version 2.0.2.1 installed)
I have a Cisco SG200 26 Port Switch, 2 Cisco WAP4410N Access points, and a VLAN aware Router. I have created 4 VLAN's. For the sake of this conversation lets call them.
98 - Intel Vpro
99 - Management
100 - General
101 - Guest
The Access points are capable of doing V LAN tagging so I plan on having them tag a guest network as V LAN 101. That can get sent to the V LAN aware router and out. No problem. I have some devices, or management pages that I don't want accessible from the general network. (Intel V pro KVM, Remote Management Cards, AP Config Menus, Switch config menu...) . I need to be able to take a V LAN unaware device, plug it into port 1, and have it communicate with V LAN 98, 99 and 100.
We have a 4410N that all the time drops the connetion. We have approx 25-30 users using wireless. But when they try to connect or are connected, the router drops the connection like a yo-yo. The firmware is updated with no difference.
The wireless connection is very unstable. It's configured with WPA2 Personal and is connected through a POE-switch with IPv4. The logs don't answer the questions why it drops the connection.
after reading the many issues reported here about the WET200's WPA abilities (or lack thereof), I doubt that there will be an easy solution to the issue I'm having, but it's worth a try.The setup consists of a WET200 that should bridge two devices in a remote room to our main network. The AP is a WAP4410N, which works beautifully with all other connected devices. The WAP4410N is set up in 'WPA2-Personal Mixed' mode, and only b/g (as n was giving other, unrelated trouble). The WET200 sees the network just fine, is able to connect and receives an IP from the DHCP server. The devices behind the bridge also have connectivity - all well so far. However, at a certain point in time, which i _believe_ to coincide with the key renewal on the AP, the bridge loses the connection to the AP, even though it reports its WLAN status on the web interface (via LAN) as connected. The AP's log shows the following (MAC address is the WLAN interface on the WET200).
View 2 Replies View RelatedIn a bit of a pickle and not sure which way to turn as I think I have exhausted all possibilities.We currently have 2 Cisco WAP4410n wireless access points running within our network. They are both on version 2.0.4.2 firmware and both on a static ip address within our infrastructure and are not working.
View 2 Replies View RelatedEvery single one of the WAP4410N units at every single client where they've been deployed is dropping the network connection.
After an undetermined amount of time, wireless devices connected to a WAP4410N begin to lose their network connection, but each will maintain their wireless connection to the WAP. The network connection will not be restored until the WAP is rebooted. It appears the affected devices are unable to obtain/renew their IP address at the time when they lose network connection. We reduced the DHCP lease time to 2 hours, and we had no problems for 2 weeks. We then changed the DHCP lease backup to 3 days and the problem returned.
This happens with one or two SSIDs in use, with or without VLANs, always in bridge mode.
Cisco support advised us that this is a known problem that was supposed to be corrected in the 2.0.4.2 firmware revision. They have found that it does work in approximately 90% of the updates from 2.0.3.3, but is still not working for some customers. It was supposed to be fixed with firmware version 2.0.6.1 (which we've tried) but no luck.
Besides the obvious "short DHCP lease" workaround, any better ideas? Is the WAP4410N a lemon?
I have installed a wired and wireless connection for a compound which is around150 squire meters. I used the Cisco wap4410n routers for the wireless setup.
The structure is like this.There is a connection coming from the service provider. There is a central switch where the connection coming from service provider, the server, one Cisco wap4410n router and other two switches are directly connected to it. Again I connected other switches to the switches getting connection from the central switch. I used Cat 5e and Cat 6 cables to connect the switches as well as the wireless routers (For more info , the cable goes underground) and I used cross-over cable to connect switch to switch and straight-through to connect routers to switches. I connected the other Cisco wap4410n routers to the switches outside( I get like 6 Cisco wap4410n routers)The wireless routers are connected to the switches which are connected to the central switch and also on the other switches.
The routers are configured to have their default AP mode.My problem The connection is very slow. The connection is down almost every week and it needs to be re-configured. The connection nice on the router which is directly connected to the central switch(but not the same on the others routers which are connected to the other switches)even when I reset them they don't fall to .245 ( which is ok I can see them on the DHCP server but I still see it as problem)when I set them as a wireless wireless repeater, full signal but no connection(given that I have set same SSID, enabled allow wireless signal to be repeated, filling MAC addresses) Down here I have tried to show the architecture diagrammatically.
We've had this AP for just over a year and just recently it started dropping its wireless connection. To fix, I have to and unplug the power and then plug it back in.. Then it works again for a few hours and drops out again. If I navigate to the config page right after it drops, all of the settings seem to be completely gone. But if I go through and unplug/plug it in again, all of the settings are back.
I updated the firmware to 2.0.4.2, but that didn't seem to resolve the problem. Is this thing a brick now?
I am trying to use some WAP4410N in client mode, not much luck.In one case they shouldt connect to different unsecured networks controlled by a Cisco 5508 controller.I can get connection to one of the SSID's but not very stable.One ssid can be seen if i switch from ap-mode to client and run a sitesurvey. If i after that run a site survey again the ssid is not shown.Cant get connected. A third ssid acts "normal" but the 4410 never connects.I have a forth case, WPA2 Personal, cant connect.Been trying fw 2.0.3.3 still no succesAre client mode not usefull at all ?
View 6 Replies View RelatedI have the following equipment:
Cisco 871W router
2x WAP 4410N APs running 2.0.3.3
I currently have 1 AP connected to the router via copper. The AP to AP link is over 802.11. I have attached a diagram reflecting the current topology.
The AP-to-AP link will come up utilizing B/G/N mixed mode; however, the connection is basically unusable. About 30% of the traffic is dropped, while the packets that do make it have a consistently volatile latency, anywhere from 15 to 1500 ms. I have had success using G-only and B/G mixed. The link is stable (I have had the best results with B/G). The problem is, I didn't buy the 2nd 4410N to run the G protocol. I would like to connect the APs running either B/G/N (hopefully negotiating to N) or N only. I am wondering if there is a certain configuration I can utilize (perhaps using WDS repeater or bridge versus Wireless Client/Repeater?), or a firmware upgrade set for release that can make this happen for me.
We have three WAP4410N that loses the connection. We've updated the firmware, changed the equipment, repeatedly reconfigured, but the problem persists.Is used the firmware 2.0.5.3 with WPA2 Enterprise Mixed authentication.
View 5 Replies View RelatedI have been using WAP4401N for almost a year in our office and I’m very happy of this device, never had any problem. So I bought 3 new ones for our customer which supposed to work in configuration below:
Network ----- AP1 –Bridge mode ----- AP2 – Bridge mode -----AP3 – Access Point mode.
Everything was working perfectly fine to the moment than bridge was broken. I can get access to all AP (obviously when connected to proper part of network) however not able to ping from AP2 -> AP1 or opposite so basically no link between AP1 and AP2. After reboot everything is working fine to next time (happens twice in two days). When I go to System Performance can see Connection is enabled but doesn’t work.
I upgraded firmware to latest version (2.0.5.3) but haven’t worked. When I’ve done some research found many users having similar problem with this device and basically they recommend to don’t buy. Unfortunately this is not an option for me as I’ve already purchased them.
My WAP4410N is configured with 4 seperate SSIDs. Two of the SSID status are showing "Enabled". The other 2 are shown as "Connected". The one that are showing as Enabled are not receiving any packets. Devices connected to the SSID that shows "Enabled" are unable to connect to the network. Any one else encountered similar issues before? This issue just surfaced few hours ago. The device has been using for around 2-3 years with minimal issues.
View 1 Replies View RelatedWe have 4x WAP4410N access points 1 AP & 3 Repeaters, this works perfect. The situation at the moment is that the internet connection is plugged in with a cable on the AP but the question is that if it's possible to plug the internet connection into one of the repeaters?
After that are we still able to use the internet over al four access points?
I have a couple incredibly annoying problems with my E4200v2. I have one Win7 laptop that connects wirelessly and has been slowed to a CRAWL connected to this new router.3 of the 4 Android powered devices I have experience random and unexplained drops in Internet access. It seems they stay connected to the router itself but they lose Internet. Happens at random times and intervals.
View 9 Replies View RelatedNot able to see devices in CS device management (0 devices).but devices are visible in other modules like RME and DFM.
View 3 Replies View RelatedI have a new notebook Sony Z217GG, I connected WAP 4400N was very smooth, but after connected WAP 4410N, the internet connecting always connect and disconnect, I check the notebook wireless model is intel 6230.
View 1 Replies View RelatedI have the Linksys EA6500 with the latest firmware and have a question regarding the device list connection status.Currently, I am seeing devices in the list that have a connection status of live, but they are not even within my home network. What is the update/cycle time for the device list actually checking connection status of a device?In my situation, it has been 3 days (72 hours) since the two device showing as connected have not been connected to my home network/router. Noticed that this inaccurate connection status for these devices is also contributing to the Device Monitr app not showing correct device connection status info.
Would like to have real-time device connection status if possible. This device list is great way to know when device get connected or disconnected which let me know when my kids get home from school or using game console when should be doing homework.
I am having trouble setting nat rules on device SRP527W-U with the latest firmware 1.2.4 (003). The latest firmware 1.2.4 has introduced the possibility to create specific nat rules via "ACL policy rules". I am trying to use this "new feature" not available in the older releases to get my network configuration done. The configuration I would like to do is to have two different vlan. In the vlan1 I would like to nat the PCs via the point_to_point interface and in the vlan2 I don't want use nat feature so each computer will be reachable via public ip address. I have configured two different PVCs on the device.
View 2 Replies View RelatedI'm trying to share my internet connection to another PC via wireless device.Which technique can i use for it.Topo:-Internet <-> PC(A) <--> WD (B) <--> WD (C) <--> PC(D)PC = Windows XP (OS)WD = Wireless device Access Point / BridgeIn the above topology, i need to share my internet connection from (A) PC to (B) PC through wireless device, I have plan to establish the internet sharing between two PC, In which mode Access Point/ Bridge mode is adequate for this wireless device to make connection and internet sharing between the PC
View 5 Replies View RelatedI have an e1200 Linksys router hooked up and working well, a wired connection to my first computer a wireless connection to my second (laptop) in the basemen and to my HDTV. My question is what Linksys device would I need to enable me to get a wireless connection in the basement to then hardwire connections to my Blue-Ray player and my HK AVR-3650.
View 2 Replies View RelatedI did some testing with a few wireless N routers and then decided to buy a Linksys e 2500 as it was on a special for $66 in Australia.The wireless routers i tested were (Belkin brand new model / Netcomm & Dlink Used ones)1. Netcomm N800n Fastest wireless transfer speed 9MBytes or 72 MBPS.2. Dlink - Around 6MBytes/s or 48MBPS.3. Belkin - Around 4-5 MBytes/secDid not test the Linksys before buying it.4. Linksys E 2500 - around 5MBytes/s = 40MBPS.After all this testing, got a new Linksys believing that a cisco device should have good quality.My problems is that the connection speed on the device stays a 72BPS whereas on the Netcomm / D-link it used to be 130mbps. Not that this bothers me, however the file transfer speed matches the Link status connection speed.The router was placed at exactly the same location, file transfer was checked by transferring large file sizes.Lan setup is1. Belkin ADSL 2+ (Modem with Wireless b/g and Voip) only being used now as an ADSL Modem and VOIP service.2. Cisco linksys e 2500.3. Media centre PC which has a wired connection to linksys e 2500.4. Main PC (Connected wireless to the linksys). The network adapter is a DLINK DWA125 N150 adapter (2.4GHZ only). The distance between the wireless adapter and the wireless router is approximately 12 feet and there is direct line of sight.5. IPAD.5. Using 2.4GHZ as i dont have a 5GHZ adapter yet. Router is only on wireless N mode.I was better off using a second hand Netcomm rather than a brand new Cisco router. The cisco router has 4 internal antennas, whereas the netcomm one had only 2 external antennas. My signal strength is excellent. Only problem is the slow internal transfer between the Main PC and the Media Center PC. Main PC is Core i7 950 where as the Media Centre is a Core 2 Duo e6400GHZ with 4GB Ram. Both PCs running Windows 7 Ultimate (Main PC) , Professional (Media Centre PC). My network knowledge is decent. Is there any settings in the advanced Wireless mode for the Linksys that can make my internal file transfers faster. [code]
View 4 Replies View RelatedI keep getting the following error on my ASA device : UNABLE TO LAUNCH DEVICE MANAGER FROM IP_ADDRESS.
I have changed/disabled web vpn just to be sure it is not an issue with the port.All necessary http access has been setup.
Appliance is ASA-5525X
asdm-66114.bin
asa861-2-smp-k8.bin
I cannot ping and end node on my system from my Cisco 2911. I've tried to configure my computer to ping the device and I am able to. It seems the difference between using my computer and the 2911 is that with my computer I am able to set the default gateway as the end node's ip.
View 1 Replies View RelatedSo I was having trouble loading a game on my computer and I was scrolling through forums looking for an answer and one answer that supposively worked for a lot of people was to unisntall and reinstall my network card.IT told me to go to devices -> right click network adapter -> uninstall -> then scan for hardwarer changes to reinstall When I clicked uninstall an error message popped up and said "Unable to uninstall device because device is required on startup" and then it apparently just uninstalled it anyway and it showed back up after I clicked "scan for hardware changes".Now ever since, everytime I try and connect to the internet my computer says "Limited or no connectivity" and I'm unable to access the internet on that computer, the computer I am on now can connect just fine, so it must have something to do with the network card that i supposively unisntalled.
View 17 Replies View RelatedI have a very annoying problem with my Linksys WRT54G2.When I connect a wireless device (laptop, phone, TV, Ipad) to my wireless network I only see a Local connection, no connection to internet. After resetting the router (power off for several seconds) the internet-connection is available again.I have to do this every 1 - 2 days.
View 7 Replies View Relatedi have a device connected to 2960 switch. It is an access port and i could ping the device from other switches , also from outside the lan. But i am not able to ping the device from 2960 switch alone. I suspected and checked the arp table and it was showing as incomplete. I created the manual arp entry and tried pinging but no luck.
View 14 Replies View RelatedI have an ASA5505 running ver 8.0(2). I have configured the ssh timeout, ssh host commands and did the crypt o key gen. I am unable to access the device from the host I am allowing. Is there like ca save all command required? I am trying to use the default pix and telnet password. Do those still work?
View 3 Replies View RelatedI have dell xps l501x with embedded 5620 mobile broadband mini card. Vz access manager says that device is disabled. How can I fix. Or in device bad and have to replace?
View 4 Replies View Related
