Cisco Wireless :: WAP4410N Output Power Setting?
Oct 27, 2009
I have a WAP4410N and would like to turn down the power output below 100%.
It has a very strong signal, and is covering our small office and half the parking lot.
In the Administration Guide, under FAQs, it mentions a setting for output power but I cannot find this setting.
The SW version is 2.0.0.5, and that seems to be the latest version - the file I downloaded is WAP4410N-fw-2.0.0.5-K9.img but I haven't installed it yet.
View 8 Replies
ADVERTISEMENT
Dec 4, 2012
I have a WAP4410N that stopped powering on with PoE. The PoE light comes on but the Power and Ethernet light remain off. The link light comes on the port on the switch. I have tried multiple switch ports and tried a different switch.
View 3 Replies
View Related
Apr 20, 2011
Currently I have a WAP4410N setup and would like to add a second WAP4410N but as wireless repeater. I want my users to have wireless access without the need to keep changing the wireless connection based on their location within the factory.
The AP Mode on teh WAP4410N gives me the options below, but I am not sure which one is the correct one:
Option 1 - Wireless WDS Repeater
Option 2 - Wireless Client/Repeater
Below is the link from cisco with explanation. [URL]
Also, if have WAP54G, can I setup this unit to be a wireless repeater with the WAP4410N devices? or all repeaters must be of the same model? Existing WAP4410 is setup to operate at Wireless B/G Mixed mode.
View 9 Replies
View Related
Apr 20, 2011
I need setting up a WAP4410n v 2.0.1.0 as a repeater. Warning, this is the first time I have worked with a repeater. I have tested with a netgear router and a Linksys 160n router. Unfortunately I only have the netgear to continue testing with since the Linksys is at my customer’s site. I can get my hands on a Linksys E3200 if I have to. I have tried a number of setting combinations and I still cannot get the signal to be repeated. So this is what I think the setup should be:I setup the router and the WAP4410n repeater to have the same ssid and channel. For security I first tried to have both the router and the repeater to use WPA2 personal using TKIP then I read that there is a problem using WPA2 with version 2 of the firmware so I then tried using WEP having both the router and repeater using the same key. I selected Wireless WDS repeater mode. I did a site survey and selected my router. Now from what I understand, which is very little, this is all I should really need to do. I have left all of the other settings to the default values. So what am I missing?
View 1 Replies
View Related
Apr 30, 2011
Setting up a WAP4410n v 2.0.1.0 as a repeater. Warning, this is the first time I have worked with a repeater. I have tested with a netgear router and a Linksys 160n router. Unfortunately I only have the netgear to continue testing with since the Linksys is at my customer's site. I can get my hands on a Linksys E3200 if I have to. I have tried a number of setting combinations and I still cannot get the signal to be repeated. So this is what I think the setup should be: I setup the router and the WAP4410n repeater to have the same ssid and channel. For security I first tried to have both the router and the repeater to use WPA2 personal using TKIP then I read that there is a problem using WPA2 with version 2 of the firmware so I then tried using WEP having both the router and repeater using the same key. I selected Wireless WDS repeater mode. I did a site survey and selected my router. Now from what I understand, which is very little, this is all I should really need to do. I have left all of the other settings to the default values.
View 2 Replies
View Related
Nov 24, 2010
Is there a recommended configuration for setting up a wap4410n as an ap?
The reason I ask is that I have an rvs4000 with a wap4410n as ap and a second wap4410n as wds repeater and it seem I have to reboot one or more of them every couple of days due to various users being unable to connect wirelessly or being able to connect wirelessly, but with no Internet access.
Starting with a reboot to facory default, the rvs4000 gave the wap4410n ap an address of 192.168.1.101 so I just left things like that. Similarly, the wap4410n wds repeater was given an address of 192.168.1.103, which I did not change.
Given there seems to be some kind of intermittent problem, would it be better to have the rvs4000 reserve an ip address for the two wap4410n? Note that I did try this, but after adding the two reserved ip addresses (192.168.1.101/103) and clicking on "save", the rvs4000 rebooted and came back up without the two reserved addresses...
View 9 Replies
View Related
Jul 3, 2011
i set up the WAP4410N and it can be connected with our router. But it's not protected by our password, but once i have set the password of WAP4410N by changing the security mode to WEP, now i will prompted to password when I connect the AP, but it shows limited connectivity, I can't even access my local LAN resources at all.
View 2 Replies
View Related
Sep 22, 2011
I need to configure WAP4410N wireless access point for our company guest and visitors.i need them to only surf internet and not to go to LAN (servers).I think i need to create VLAN for this ? can any one tell me setting for configure only to surf internet thru WAP4410N ?
View 1 Replies
View Related
Jul 12, 2011
Only because we want to updeate A/C system in server room, we need to know what Cisco 2800's the power usage and heat output are. It is on the racks and can't see its spesc.
View 1 Replies
View Related
Jan 31, 2012
I have a WS-C6509-E (R7000) and am trying to implement some proactive monitoring for environmental alerts. What is the output from a Power Supply failure for the following “sh log” “sh environment alarm”.
View 1 Replies
View Related
Apr 29, 2011
On my D-link routher the power supply broke. I instal another one but it has 2.5A as output instead of 2A as the broken one has. Is it dangerous.
View 2 Replies
View Related
Mar 6, 2012
We are trying to setup a WAP4410N with 2 SSID's. One SSID for our private network and the other for guest internet access. On the VLAN and QoS page there is a setting for priority. What would be the suggested values for this setting? We obviously want our private network to receive priority over our guest network.Also, does VLAN Tag setting need to be on Tagged to determine private from guest traffic?
View 2 Replies
View Related
Aug 26, 2012
Is there a way to ask the above switch how much power it's supplying to various ports?I've found some stuff in POWER-ETHERNET-MIB, but it's only the main power supply and the up/down status of the various ports.
It looks like what I want is
[URL]
but my SG500 tells me:
snmpwalk -v2c -cpublic serverswitch 1.3.6.1.4.1.9.9.402
CISCO-SMI::ciscoMgmt.402 = No Such Object available on this agent at this OID
View 6 Replies
View Related
Sep 6, 2012
I would like to ask the correct part number of the power adapter on WAP4410N?
View 4 Replies
View Related
Dec 1, 2011
We have a WLC 4402 controlling 40+ LWAPs. Is there a way to keep Tx power level assignment dynamic, but set the time of day it does it? I'd like to minimize user impact. (Firmware v. is 7.0.116.0)
View 2 Replies
View Related
Oct 12, 2011
I have AP1 setup with WPA2-Enterprise. How would I setup AP2 (WAP4410N) to be a repeater for AP1?
View 1 Replies
View Related
Apr 18, 2012
Im having problems with setting up my cisco WAP4410N as a repeater to extend the signal of cisco E2500.It works fine when there is no password to be set on both devices. But when either one of these devices had beenset a password on it, then WAP4410N failed to extend the signal of E2500.
I tried steps as below:
1. Same password type in WAP4410N and E2500.
2. Different password type in WAP4410N and E2500.
3. Set password in WAP4410N ONLY.
4. Set password in E2500 ONLY.
All steps above makes WAP4410N fail to extend the signal range of E2500. WAP4410N successfully works as a repeater to extend the signal of E2500 when there is no password to be set on both devices.
View 2 Replies
View Related
Apr 30, 2011
I have the following equipment:
Cisco 871W router
2x WAP 4410N APs running 2.0.3.3
I currently have 1 AP connected to the router via copper. The AP to AP link is over 802.11. I have attached a diagram reflecting the current topology.
The AP-to-AP link will come up utilizing B/G/N mixed mode; however, the connection is basically unusable. About 30% of the traffic is dropped, while the packets that do make it have a consistently volatile latency, anywhere from 15 to 1500 ms. I have had success using G-only and B/G mixed. The link is stable (I have had the best results with B/G). The problem is, I didn't buy the 2nd 4410N to run the G protocol. I would like to connect the APs running either B/G/N (hopefully negotiating to N) or N only. I am wondering if there is a certain configuration I can utilize (perhaps using WDS repeater or bridge versus Wireless Client/Repeater?), or a firmware upgrade set for release that can make this happen for me.
View 1 Replies
View Related
Dec 27, 2012
I'm trying to get some clarity on power stacking 3750X switches. I have a new stack of 6 switches. I know I can only have 4 in a power stack and all 6 in the data stack with a max of 8. I'm trying to find the proper way to connect the power stack cables for the 4 switch power stack.
View 1 Replies
View Related
Jul 21, 2011
I keep getting alerts from our WCS stating that our 1252s are drawing low power. Now I am aware that they require enhanced PoE (up to 20W) but as we only have standard PoE in that building we purchased the 1252 series power injectors to go with them.
However, even with the correct power injectors the WCS still reports the draws low power error.
Is this a bug? Running WCS 7.0.172 at the moment.
Forgot to say we are using the PWR-INJ4 and the injector status is enabled and you see the injector MAC address when you drill in to the AP status.
View 9 Replies
View Related
Feb 14, 2013
Like the way you do with the Cisco IOS.
ie show start | i router
View 1 Replies
View Related
Dec 26, 2012
Is there a command like the "| include" command to filter comand results? For example say I want to find a specific client mac in the "sh dhcp leases" output. On a router or switch I would just type "sh ip dhcp binding | include (mac address). Is there something like this on the WLC CLI?
View 4 Replies
View Related
Jun 9, 2013
I am receiving the following error on 3750 stack switches. have already verified the power status and found ok.
IOS used: Cisco IOS Software, C3750E Software (C3750E-UNIVERSALK9-M), Version 12.2(55)SE3, RELEASE SOFTWARE (fc1)
211540: Jun 10 10:45:17.935 UTC: %PLATFORM_STACKPOWER-4-UNBALANCED_PS: Switch 4's power stack has unbalanced power supplies
211541: Jun 10 10:46:18.045 UTC: %PLATFORM_STACKPOWER-4-UNBALANCED_PS:
[Code]....
View 1 Replies
View Related
Sep 4, 2012
After stacking two 3750X switches, with four equal power-supply's, with StackWise and PowerStack , still got the next message every few hours %PLATFORM_ENV-1-FRU_PS_ACCESS: FRU Power Supply is not responding (gn4m-rt1p08-04-2)( note that the message revers to the second switch in the stack ) although the stackwise and powerstack on the switches is oke and are working correctly. !
Config : Stack-power in power-sharing mode/strict With CLI on the switch : All the power supply's and stack-power details, prio look OK.
Only: LMS prime /inventory/cisco-view/configure/power supply status result : some power supply's are marked as disabled.with the command > power supply 2 slot a off/on I manage to get the status back to "normal", but after a few hours some power supply's are again marked as "disabled".
Looks like SNMP en IOS difference from opinion.
Hardware
WS-C3750X-24S-S
C3KX-PWR-350WAC
Software
15.0(2)SE
C3750E-UNIVERSALK9-M
View 5 Replies
View Related
Apr 14, 2013
We have two switches of the same model (WS-C3560-48PS-S) that are not providing PoE. I'm trying to remotely determine what the cause of the issue is.
Here is some output.
Hostname#show power inlineAvailable:0.0(w) Used:0.0(w) Remaining:0.0(w)
Interface Admin Oper Power Device Class Max (Watts)--------- ------ ---------- ------- ------------------- ----- ----Fa0/1 auto off 0.0 n/a n/a 15.4Fa0/2 auto off 0.0 n/a n/a 15.4Fa0/3 auto off 0.0 n/a n/a 15.4Fa0/4 auto off 0.0 n/a n/a 15.4Fa0/5 auto off 0.0 n/a n/a 15.4Fa0/6 auto off 0.0 n/a n/a 15.4Fa0/7 auto off 0.0 n/a n/a 15.4Fa0/8 auto off 0.0 n/a n/a 15.4Fa0/9 auto off 0.0 n/a n/a 15.4Fa0/10 auto off 0.0 n/a n/a 15.4(code)
View 1 Replies
View Related
Feb 28, 2011
I have a 6500 chassis with 2 power supplies. At the moment I am using the default configuration:
power-redudancy mode redundant
The problem is that an inserted module is in "power deny" state due too insufficient power.
I know, that It's not a good idea to change into combined mode (loss of redundancy), but my customers requested this anyway.
So I will change to combined mode. So here's the 1 million dollar question: "Which modules will go into power deny, if one of my power supplies fails?"
The 6500 config guide states:
"Power supply is removed withredundancy disabled
• System log and syslog messages are generated.
• System power is decreased to the power capability of one supply.
• If there is not enough power for all previously powered-up modules, some modulesare powered down and marked as power-deny in the show power oper state field."
Well, do you know if there's any way to configure some kind of priority? E.g. I definetly don't want by 10Gig Module or WiSM module to be in power deny. Can i statically make sure, those module will be powered on for sure? Like: "power enable module slot_number" How is this calculated? Or is random?
View 3 Replies
View Related
Apr 4, 2012
In a stand alone 3750x switch configuration, can the secondary power supply only act as a redundant power supply (active/standby), or can it become a "pool" of power similar to power sharing mode for StackPower (somewhat active/active)? I understand there is no stack involved here but I'm curious if this functionality is possible.
View 1 Replies
View Related
Dec 5, 2012
how can I enable an automatic power-on after a power failure on an ASA 5512-X?
View 5 Replies
View Related
May 2, 2011
I have a H.264 web cam with a built in server attached to a 1 watt Powerlink(N) router(bridge) connecting wirelessly outside (100 feet)to my Dlink 655. My computer connects wirelessly(60 feet) through the house via a 1 watt Powerlink USB adapter to the 655 also. It was the Network from hell to get up and going, but it is functional? now.I have the Dlink with a web server port open outputting the video. I can access internal and externally via IE with a Dyndns domain so its all working.Dlink says I'm getting 80-160mbps from the web cam and 25-55mbps from my computer.The Problem: Camera server comes up fine and starts to stream great video for 2-5 seconds then its like the bandwidth gets used up and it gets choppy, stalls for long periods ETC ETC. I have Nat TCP and UDP set to End point independent if that makes a difference.
View 10 Replies
View Related
Nov 5, 2012
How do I best add one or two additional wireless output ports to a fully used four port wired router?
View 3 Replies
View Related
Nov 23, 2012
I have had a DIR-655 router for a few years now, but slowly over time the wireless output has gone down. I have tried changing parameters to only-g or only-n, rebooted, changed other parameters based on what I have read in some of the forums, but have not been able to restore the power. It has an ANT24-230 antenna, and the latest firmware update 1.35NA. Different devices all show the same thing, that even next to the antenna the strength is only 80% in spite of the fact that the wireless output is set to max.
even though I have been working on this for a couple of months now, and am considering buying a new 11AC or 900N router if this is not fixable.
View 2 Replies
View Related
Mar 3, 2013
how can I enable an automatic power-on after a power failure on an ASA 5512-X?
View 12 Replies
View Related
Mar 7, 2013
How to approach an overnight upgrade from autonomous AP1231/1242 deployment into a 2504 controller-based AP1602 deployment.I do not have access to the existing 1231/1242 deployment ==> I need to ask network manager for all necessary config info to be ported onto the 2504.Example: the 1231 show run output does not list the various SSID that are in use.Therefore the question is: which commands' output do I need to ask to have all possible config data from 1231/1242 to use when configuring the 2504/1602 deployment.
View 2 Replies
View Related
