Cisco Wireless :: 2504 WLC Shows Link Status Down
Oct 10, 2012
I have connected my 2504 to a 3560 switch via a UTP SFP on a Gig port.
I have my management on 10.0.0.x I have tried tagging the port and untagging.
When I connect to the 3560 the interface comes up a-1000 a-full but when I look on the WLC the port I am using, port 1, shows Link status down.
The green light is on both the WLC port and the 3560 port but I cannot get the link status to come up on the WLC nor can I ping the WLC.
It must be something dumb I have missed.
The WLC port is autonegotiate too.
View 7 Replies
ADVERTISEMENT
Aug 6, 2011
I updated the firmware of my DIR601 to 1.02NA, it now only show NA under status for WAN, even though its connected (PPPoE). It worked with 1.01NA. I tried rebooting the router but no effect
View 1 Replies
View Related
Nov 29, 2012
This is regarding an issue with one of my access point. The access point 1252 is autonomous one running the IOS version C1250 Software (C1250-K9W7-M), Version 12.4(10b)JDA3, RELEASE SOFTWARE (fc1)
The status of the dot11Radio 0 interface is showing as RESET. I have pasted the interface brief details below.
ap03#
ap03#
ap03#sh ip int brief
[Code].....
View 10 Replies
View Related
Oct 21, 2012
1552 E Ap with a 2504 WLC. Single Root Ap with Mesh the Mesh has the problem. Both Power Injector and AP has been replaced . How do you turn on the 802.11 B Radio? No other problems at 40 other sites with identical installation.
View 1 Replies
View Related
Nov 19, 2012
My 1394 status shows connected. But the lite on my input cable is not on?
View 1 Replies
View Related
Feb 5, 2013
network icon missing which shows the status of the connection
View 8 Replies
View Related
Feb 27, 2012
On a 4500 switch having a single sup engine, another sup engine was installed to act as redundant one.the redundancy mode was changed to sso, thereafter the secondary sup was prompted to be reset.
After it came back up again, the redundancy status still shows as RPR in operation mode.
View 9 Replies
View Related
Nov 19, 2011
I just hooked up my DIR-655 yesterday and it seems to be working very well. The only problem I've got is that the Wireless Status page is empty. It filled in with data one time only, and it showed connections, protocols, speeds, etc. that seemed correct.
View 14 Replies
View Related
May 7, 2008
I am trying to install a AIR-BR1310G wireless link between two buildings. I configured the setup in a lab and had everything functioning. Shipped it to the client who is now trying to install it. The radio link is up, but we are having issues with the remote Ethernet connection.The root bridge is connected to a WS-C3560G-24TS (core) switch. The port is setup as a trunk with a native vlan of 2 (our management vlan). [code] if I do a "show power-injector" on the remote radio (no Ethernet link), I get: "Received zero AutoMIB packet from Power Injector, Check to see if CDP is disabled on Fast ethernet" repeating. No other entries. If I do the same command on a unit with a link (root bridge) I get information about "Power Injector Port 0 speed 100Mb/s duplex full link up enabled yes" with a bunch of stats. Similar for "Power Injector Port 1". Power Injector Ports 2-4 as "down" and 5-6 as "disabled". Other than the 3 different patch cables they tried (all straight through) or a crossed cable (try tomorrow when they buy one), is there any other reason the port won't go Up/Up?
View 3 Replies
View Related
Sep 26, 2010
My wireless connection for my laptop is showing upas N on Win 7 but G on DIR-655 status page??? I'm confused. Am I getting N speeds/coverage or stuck with G. If G, why? I've tried wiping my wireless network config. on Windows and reestablishing it, but no change. The DIR-655 config page shows my machine connected at 54 Mbps and Type as G
View 8 Replies
View Related
Feb 4, 2013
Region : Italy
Model : TL-WR740N
Hardware Version : Not Clear
Firmware Version :
ISP : Alice (Telecom)
I bought some days ago Tp-Link Wireless Router (Model TL-WR740N - 150 Mbps - Ver 4.23) but I couldn't install it: when I do Easy Setup Assistant, the network status test always fails because of absence of connectivity. I can see that there are some problems by the lights of the router: the WLAN light switches on, as the WAN light and the LAN light, instead of being flashed. I tried to do the installation without cd but, clicking on 192.168.1.1, I didn't find the page to access to web console but the Telecom page of the status of my connexion (nb: it reports that ethernet is unplugged).
View 3 Replies
View Related
Apr 15, 2013
Region : United Kingdom
Model : TD-W8970
Hardware Version : V1
Firmware Version : 0.6.0 1.2 v000c.0 Build 130201 Rel.54921n
ISP : O2
I have sent the following trouble ticket to TP Link Support hoping they can shine some light/fix a VPN issue I am experiencing with the TD-W8970 router.
Please see the text below.........
I have 2 tunnels set up on my TP Link TD-W8970 and although both of these work for a a while, they both drop out after 24-36 hours for no apparent reason. The tunnels still show as "up" in the router, but I lose PING and connectivity to my remote systems. The only thing that seems to fix this is to reboot the router.
I have tried the tunnels with and without "DPD" (Dead Peer Detection) enabled and the results are the same.
I have 2 other friends who have the exact router with the same firmware (latest version), and they too have the same issue.
There is nothing in the logs showing any disconnection of the VPN, and as I have mentioned, the tunnel still shows as "up" on both ends. Its almost as if the service has stopped running, but I cannot check this.
View 6 Replies
View Related
Apr 18, 2013
Region : UnitedStates
Model : TL-WR1043ND
Hardware Version : Not Clear
Firmware Version :
ISP : HughesNet
I received this router today, I have a MacBook Pro and a iPhone. The router came with a very small cd, I was very disappointed because , when I purchased this router from amazon , the discription read that this router is Mac compatiable. But that is not true if the cd is not compatiable! My problem is I get a good signal for wifi, but I can not open any websites with my Mac or my iphone.
View 1 Replies
View Related
Mar 23, 2013
Region : United States
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP :
I just got the TL-WDR3600.
It seems to work fine and my Smart TV recognizes my network drive or usb hdd connected to the router.
However, the files on the network drive or usb hdd don't seem to appear/work. The folder the files are stored in are recognized, but not the files themselves.
I've plugged the usb HDD directly to the TV and it recognizes and plays the movie files fine, however when trying to find them via the wireless router, they don't appear/work.
Are there some settings i need to change to allow the TV to see/play the files?
View 1 Replies
View Related
Oct 21, 2011
I have had this router for a while now and I have been experiencing these problems for forever. I can't seem to have two Xbox360's stay on OPEN NAT type permanently. I have tried port forwarding both xbox's, just my xbox, just my dad's xbox etc.. I have tried DMZ on one with or without the other on Port Forwarding. I have turned UPNP on I have it so the filtering is set to endpoint independent . I have tried without . I have even tried port triggering today. I have manually set static ip addresses on both the xbox and the router. I even have the most recently upgraded firmware. Now... How do I get TWO Xbox 360's on OPEN NAT ? How to get two xbox360's on permanent OPEN NAT status.
View 6 Replies
View Related
Oct 15, 2012
I Have asa 5520 with the code 8.0, the mem shows 94% and the CPU shows 85%
View 5 Replies
View Related
Nov 5, 2012
I'm trying to use my installed (working, clean) SD card, but on the SD management screen doesn't list it. Instead, where the SD status is it says "SD Status : Reinitialization". I'm a techie guy so I've done all the standard things you'd try: I've made sure it's pushed in all the way, that it's in the right way (it really only goes in one way), and that's it's a writable (tried it on another device). I've also upgraded the firmware (it was almost current already), reformatted the card, reset and restarted the device, etc.
View 8 Replies
View Related
May 11, 2013
I have an older rev a DIR-655 that has served me well. Today I finally upgraded my ISP to cable (from a slower DLS connection) to get reasonable speed/price All is working very well but unlike my old DSL modem the internet status light on the DIR-655 blinks very rapidly all the time instead of when traffic is passed.The new modem is a Motorola SB6141,I am running the latest firmware 1.35NA I went through a complete re-setup to see if that would calm the light but no dice there. (the settings arrived at were basically the same for the old Sprint modem) ,Is there something I am missing or is it time to retire the old DIR-655 for something more current.
View 5 Replies
View Related
Feb 21, 2012
Why the IOS on 4500 doesn't support globally, although am running the IOS 12.2,need for logging event link-status global.
View 3 Replies
View Related
Mar 5, 2012
Ever since I updated my firmware to 1.01 my web interface for the network settings screen has been random. Somtimes it shows a DHCP reservation list, sometimes it doesn't. Sometimes there are reservations, sometimes there are selectable radio buttons. I guess I'm just trying to figure out if this is a firmware issue or not. Ever since I updated the firmware it has been flakey.... But I was having issues with other stuff before that. When there are no reservations, sometimes i can't even select any computers because there aren't any in the drop down, when all of my hardware is online?
View 6 Replies
View Related
Apr 6, 2013
Region : Australia
Model : TL-MR3420
Hardware Version : V2
ISP : Telstra Bigpond
I have no access to the router ATM, but when I went to update, it was the latest version and build of the foirmware.I have read several reports of successful use of these two. I connect the MR 3420 to the PC, power it up. I connect BP3-EXT to the router and power it up. The MR 3420 router shows a very brief connect to the USB-based modem.: the USB light on the router stays on for about 2-3 seconds. The WLAN light on the router is on, showing a signal.
Running the setup has resulted in a couple of things. The Router's page shows that is knows the MODEM is attached to Telstra, in Australia. I do not get to put in #99# or my name and password. "Next" results in either a freeze of the Router's page "Connecting...." or I get to step through to "Congratulations, you have finished. Now connecting you to the Net"...with absolutely nothing happening on either the router or the modem. I am not sure how it thinks I am going to log in.If I do put in manual username and password, it freezes when I try to go Next.I _think_ that if the router page is frozen, it responds better if I pull the modem out of the router's USB socket.The modem works fine if plugged straight into the computer.I do remember I had a lot of trouble using a different brand of 3g router a couple of years back. Unfortunately, after I got it working, the router died.
View 5 Replies
View Related
Mar 26, 2011
I connected my camera to my router with a network cable. It is a DCS-2121, H/W Ver A2, with firmware 1.04_FR.It received an IP address and I could access it fine with a web browser.Then I configured it to work wireless.I disconnected the cable but the camera wasn't accessible.Since I couldn't find it I re-attached it with a network cable, but this didn't work.So I pressed the Reset button to start over again.However, now I cannot get it to work anymore. When I plug in the camera and have it connected with a network cable to the router the status light remains RED.When I plug it in without a network cable the status led remains RED.When I connect it with a network cable to a computer directly, the status led remains RED.I've tried changing the network settings of my router to use 192.168.0.x as range, but it makes no difference. In all cases the status indicator remains RED.
View 2 Replies
View Related
Sep 16, 2012
a few day l have 3 AP Ligthweight 1250, today l was checking my infrastructure and l saw that these 3 AP can´t join to the controller, l reset the AP to the, and its can not join, l checked physicly the AP, and the Ethernet Led is in Amber permanent and the Radio Led is in Green permanet , i am searching the status led to find the fix but l have not found these convination led. and l can not access to the consolo port.
View 2 Replies
View Related
Dec 20, 2011
I am running the following
WLC: 7.0.220
MSE: 7.0.220
NCS: 1.0.2.29
NCS shows Controller is not reachable from MSE. I am able to ping to and from the Controller and MSE.Sychronization service is showing everything being synchronize. Removed and MSE from NCS and add it back in several times.
View 8 Replies
View Related
Nov 1, 2012
The last three new APs I have received from our supplier (official Cisco 1142 LAPs) have all successfully connected to our 4400 series WLCs but are all reporting as being in an Operational Status of 'Down' ie their A/B/G/N radios are not broadcasting even though the APs are all in an enabled state. Furthermore, there is no steady green light showing on the APs - there is no light showing whatsoever (although they were displaying the familiar red-orange-green lights while they were pulling down the IOS images from the WLCs).
The only strange thing I have noticed is that in the AP config screen, the ‘Mini IOS version’ is shown as being v7.3.x. The other – working APs – we have of the 1142 series show v3.x. I know that controller code v7.2 and above only work with the newer 5500 and 7500 series WLCs. Could this be the issue and have any of you seen this issue previously? I am running WLC code v7.0.230.0.
View 34 Replies
View Related
May 17, 2012
I have a Cradlepoint MBR1000, it has updated the firmware automatically to 2.0.0. Now I cannot see anything that is connected to it. In other words it will not show any connected equipment in the wireless status, and it will not show DHCP status. I have done a hard reboot and still don't see anything. Everything works, everyone is able to connect, but I can't see them..
View 1 Replies
View Related
Feb 16, 2010
I have a Cisco 2106 WLC, and a 1131ag Access Point. The 802.11a/g Radio "Operational Status" = DOWN. All other Radios are UP. I'm wondering if this is normal behavior as no clients are connecting to it over the 802.11a/g Radio.
View 8 Replies
View Related
Aug 25, 2011
We have two autonomous access point 1142 series running 12.4(21a)JA1 and randomly the Dot11Radio0 interface goes into reset/down state. At first I thought it was something related to power consumption issue on the switch, but looking at the remaining (w) I have plenty.
View 8 Replies
View Related
Aug 20, 2012
We have 1242-AG series AP which is configured in Rogue Detector mode. After adding this AP to WLC its showing Admin Status of AP as Down.
When i am trying to enable the Admin Status its giving me following error
" Admin status cannot be enabled for AP in Rogue Detector mode".
how to enable Admin Status for Rogue Detector AP.
View 4 Replies
View Related
Apr 21, 2013
I want to set up AP 1552 as outdoor access point so serve clients. This AP is connected to 3750X switch and recieving power over ethernet.Now, by default AP 1552 come with bridge mode and it cannot be changed to local mode. I read on one of the post and made it ROOTAP but still the OPER STATUS is down. This device is already registered to my WLC.
what needs to be done to bring the AP in operational status.[code]
View 3 Replies
View Related
Dec 2, 2011
the product keeps saying that a network error has occured however, when i check the network status it says connected and the signal strength is at 100%.
View 1 Replies
View Related
Sep 24, 2011
Wireless status is connected but internet won't work
Microsoft Windows [Version 6.1.7600]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:UsersNate>IPCONFIG/ALL
Windows IP Configuration
Host Name . . . . . . . . . . . . : Owner-PC
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
[code]....
View 1 Replies
View Related
Jul 24, 2011
give us the option to disable the front status led too.
View 9 Replies
View Related
