D-Link DIR-601 :: WAN Status Shows NA

Aug 6, 2011

I updated the firmware of my DIR601 to 1.02NA, it now only show NA under status for WAN, even though its connected (PPPoE).  It worked with 1.01NA.  I tried rebooting the router but no effect

View 1 Replies


ADVERTISEMENT

Cisco Wireless :: 2504 WLC Shows Link Status Down

Oct 10, 2012

I have connected my 2504 to a 3560 switch via a UTP SFP on a Gig port.
 
I have my management on 10.0.0.x  I have tried tagging the port and untagging.
 
When I connect to the 3560 the interface comes up a-1000 a-full but when I look on the WLC the port I am using, port 1, shows Link status down.
 
The green light is on both the WLC port and the 3560 port but I cannot get the link status to come up on the WLC nor can I ping the WLC.
 
It must be something dumb I have missed.
 
The WLC port is autonegotiate too.

View 7 Replies View Related

1394 Status Shows Connected - Can't Connect To Internet

Nov 19, 2012

My 1394 status shows connected. But the lite on my input cable is not on?

View 1 Replies View Related

Network Icon Missing Which Shows The Status Of The Connection?

Feb 5, 2013

network icon missing which shows the status of the connection

View 8 Replies View Related

Cisco Wireless :: AP 1252 Dot11radio Interface Status Shows Reset

Nov 29, 2012

This is regarding an issue with one of my access point. The access point 1252 is autonomous one running the IOS version C1250 Software (C1250-K9W7-M), Version 12.4(10b)JDA3, RELEASE SOFTWARE (fc1)
 
The status of the dot11Radio 0 interface is showing as RESET. I have pasted the interface brief details below.
 
ap03#
ap03#
ap03#sh ip int brief

[Code].....

View 10 Replies View Related

Cisco Switching/Routing :: 4500 Redundancy Status Still Shows As RPR In Operation Mode

Feb 27, 2012

On a 4500 switch having a single sup engine, another sup engine was installed to act as redundant one.the redundancy mode was changed to sso, thereafter the secondary sup was prompted to be reset.
 
After it came back up again, the redundancy status still shows as RPR in operation mode.

View 9 Replies View Related

D-Link DIR-655 :: Wireless Status Not Populating

Nov 19, 2011

I just hooked up my DIR-655 yesterday and it seems to be working very well. The only problem I've got is that the Wireless Status page is empty. It filled in with data one time only, and it showed connections, protocols, speeds, etc. that seemed correct.

View 14 Replies View Related

D-Link DIR-825 :: Get 2 Xbox360 On Permanent Open NAT Status?

Oct 21, 2011

I have had this router for a while now and I have been experiencing these problems for forever. I can't seem to have two Xbox360's stay on OPEN NAT type permanently. I have tried port forwarding both xbox's, just my xbox, just my dad's xbox etc.. I have tried DMZ on one with or without the other on Port Forwarding. I have turned UPNP on I have it so the filtering is set to endpoint independent . I have tried without . I have even tried port triggering today. I have manually set static ip addresses on both the xbox and the router. I even have the most recently upgraded firmware. Now... How do I get TWO Xbox 360's on OPEN NAT ? How to get two xbox360's on permanent OPEN NAT status.

View 6 Replies View Related

D-Link DCS-942L :: MicroSD Not Reading - Saying SD Status - Reinitialization

Nov 5, 2012

I'm trying to use my installed (working, clean) SD card, but on the SD management screen doesn't list it.  Instead, where the SD status is it says "SD Status : Reinitialization".  I'm a techie guy so I've done all the standard things you'd try: I've made sure it's pushed in all the way, that it's in the right way (it really only goes in one way), and that's it's a writable (tried it on another device). I've also upgraded the firmware (it was almost current already), reformatted the card, reset and restarted the device, etc. 

View 8 Replies View Related

D-Link DIR-655 :: Internet Status Light Blinks Very Rapidly

May 11, 2013

I have an older rev a DIR-655 that has served me well. Today I finally upgraded my ISP to cable (from a slower DLS connection) to get reasonable speed/price All is working very well but unlike my old DSL modem the internet status light on the DIR-655 blinks very rapidly all the time instead of when traffic is passed.The new modem is a Motorola SB6141,I am running the latest firmware 1.35NA I went through a complete re-setup to see if that would calm the light but no dice there. (the settings arrived at were basically the same for the old Sprint modem) ,Is there something I am missing or is it time to retire the old DIR-655 for something more current.

View 5 Replies View Related

Cisco Firewall :: ASA 5520 - Memory Shows 94% And CPU Shows 85%

Oct 15, 2012

I Have asa 5520 with the  code 8.0, the mem shows 94% and the CPU shows 85%

View 5 Replies View Related

D-Link DIR-825 :: Sometimes Shows A DHCP Reservation List

Mar 5, 2012

Ever since I updated my firmware to 1.01 my web interface for the network settings screen has been random. Somtimes it shows a DHCP reservation list, sometimes it doesn't. Sometimes there are reservations, sometimes there are selectable radio buttons.  I guess I'm just trying to figure out if this is a firmware issue or not. Ever since I updated the firmware it has been flakey.... But I was having issues with other stuff before that. When there are no reservations, sometimes i can't even select any computers because there aren't any in the drop down, when all of my hardware is online?

View 6 Replies View Related

D-Link DIR-655 :: Wireless Connection Showing Up N On Windows 7 But G On Router Status Page?

Sep 26, 2010

My wireless connection for my laptop is showing upas  N on Win 7 but G on DIR-655 status page???     I'm confused.  Am I getting N speeds/coverage or stuck with G.  If G, why?  I've tried wiping my wireless network config. on Windows and reestablishing it, but no change.  The DIR-655 config page shows my machine connected at 54 Mbps and Type as G

View 8 Replies View Related

TP-Link 150Mbps Wireless :: TL-WR740N - Network Status Test Failed

Feb 4, 2013

Region : Italy
Model : TL-WR740N
Hardware Version : Not Clear
Firmware Version :
ISP : Alice (Telecom)

I bought some days ago Tp-Link Wireless Router (Model TL-WR740N - 150 Mbps - Ver 4.23) but I couldn't install it: when I do Easy Setup Assistant, the network status test always fails because of absence of connectivity. I can see that there are some problems by the lights of the router: the WLAN light switches on, as the WAN light and the LAN light, instead of being flashed. I tried to do the installation without cd but, clicking on 192.168.1.1, I didn't find the page to access to web console but the Telecom page of the status of my connexion (nb: it reports that ethernet is unplugged).

View 3 Replies View Related

Cisco Wireless :: 1300 Series Bridge And FastEthernet Link Status

May 7, 2008

I am trying to install a AIR-BR1310G wireless link between two buildings.  I configured the setup in a lab and had everything functioning.  Shipped it to the client who is now trying to install it.  The radio link is up, but we are having issues with the remote Ethernet connection.The root bridge is connected to a WS-C3560G-24TS (core) switch.  The port is setup as a trunk with a native vlan of 2 (our management vlan).  [code] if I do a "show power-injector" on the remote radio (no Ethernet link), I get: "Received zero AutoMIB packet from Power Injector, Check to see if CDP is disabled on Fast ethernet" repeating.  No other entries.  If I do the same command on a unit with a link (root bridge) I get information about "Power Injector Port 0 speed 100Mb/s duplex full link up enabled yes" with a bunch of stats.  Similar for "Power  Injector Port 1".  Power Injector Ports 2-4 as "down" and 5-6 as "disabled". Other than the 3 different patch cables they tried (all straight through) or a crossed cable (try tomorrow when they buy one), is there any other reason the port won't go Up/Up?

View 3 Replies View Related

Cisco Switching/Routing :: 4500 For Logging Event Link Status Global

Feb 21, 2012

Why the IOS on 4500 doesn't support globally, although am running the IOS 12.2,need for logging event link-status global.

View 3 Replies View Related

TP-Link ADSL2+ Wireless :: TD-W8970 - VPN Disconnection But Tunnel Still Shows As Up

Apr 15, 2013

Region : United Kingdom
Model : TD-W8970
Hardware Version : V1
Firmware Version : 0.6.0 1.2 v000c.0 Build 130201 Rel.54921n
ISP : O2

I have sent the following trouble ticket to TP Link Support hoping they can shine some light/fix a VPN issue I am experiencing with the TD-W8970 router.

Please see the text below.........

I have 2 tunnels set up on my TP Link TD-W8970 and although both of these work for a a while, they both drop out after 24-36 hours for no apparent reason. The tunnels still show as "up" in the router, but I lose PING and connectivity to my remote systems. The only thing that seems to fix this is to reboot the router.

I have tried the tunnels with and without "DPD" (Dead Peer Detection) enabled and the results are the same.

I have 2 other friends who have the exact router with the same firmware (latest version), and they too have the same issue.

There is nothing in the logs showing any disconnection of the VPN, and as I have mentioned, the tunnel still shows as "up" on both ends. Its almost as if the service has stopped running, but I cannot check this.

View 6 Replies View Related

TP-Link 3G/3.75G Router :: MR3420 Shows Very Brief Connect To USB-based Modem

Apr 6, 2013

Region : Australia
Model : TL-MR3420
Hardware Version : V2
ISP : Telstra Bigpond

I have no access to the router ATM, but when I went to update, it was the latest version and build of the foirmware.I have read several reports of successful use of these two. I connect the MR 3420 to the PC, power it up. I connect BP3-EXT to the router and power it up. The MR 3420 router shows a very brief connect to the USB-based modem.: the USB light on the router stays on for about 2-3 seconds. The WLAN light on the router is on, showing a signal.

Running the setup has resulted in a couple of things. The Router's page shows that is knows the MODEM is attached to Telstra, in Australia. I do not get to put in #99# or my name and password. "Next" results in either a freeze of the Router's page "Connecting...." or I get to step through to "Congratulations, you have finished. Now connecting you to the Net"...with absolutely nothing happening on either the router or the modem. I am not sure how it thinks I am going to log in.If I do put in manual username and password, it freezes when I try to go Next.I _think_ that if the router page is frozen, it responds better if I pull the modem out of the router's USB socket.The modem works fine if plugged straight into the computer.I do remember I had a lot of trouble using a different brand of 3g router a couple of years back. Unfortunately, after I got it working, the router died.

View 5 Replies View Related

Tp-link 300mbps Wireless :: Tl-wr1043nd / Wifi Shows Good Signal But No Internet?

Apr 18, 2013

Region : UnitedStates
Model : TL-WR1043ND
Hardware Version : Not Clear
Firmware Version :
ISP : HughesNet

I received this router today, I have a MacBook Pro and a iPhone. The router came with a very small cd, I was very disappointed because , when I purchased this router from amazon , the discription read that this router is Mac compatiable. But that is not true if the cd is not compatiable! My problem is I get a good signal for wifi, but I can not open any websites with my Mac or my iphone.

View 1 Replies View Related

TP-Link Dual-Band Wireless :: TL-WDR3600 Media Share Shows Folders But Not Files On Smart Tv

Mar 23, 2013

Region : United States
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP :

I just got the TL-WDR3600.

It seems to work fine and my Smart TV recognizes my network drive or usb hdd connected to the router.

However, the files on the network drive or usb hdd don't seem to appear/work. The folder the files are stored in are recognized, but not the files themselves.

I've plugged the usb HDD directly to the TV and it recognizes and plays the movie files fine, however when trying to find them via the wireless router, they don't appear/work.

Are there some settings i need to change to allow the TV to see/play the files?

View 1 Replies View Related

D-Link DCS Network Camera :: 2121 - When Plugged In Without Network Cable / Status Led Remains Red

Mar 26, 2011

I connected my camera to my router with a network cable. It is a DCS-2121, H/W Ver A2, with firmware 1.04_FR.It received an IP address and I could access it fine with a web browser.Then I configured it to work wireless.I disconnected the cable but the camera wasn't accessible.Since I couldn't find it I re-attached it with a network cable, but this didn't work.So I pressed the Reset button to start over again.However, now I cannot get it to work anymore. When I plug in the camera and have it connected with a network cable to the router the status light remains RED.When I plug it in without a network cable the status led remains RED.When I connect it with a network cable to a computer directly, the status led remains RED.I've tried changing the network settings of my router to use 192.168.0.x as range, but it makes no difference. In all cases the status indicator remains RED.

View 2 Replies View Related

Limited Or No Connectivity Status

Feb 19, 2012

recently my internet connection shows the status i mentioned.in cmd ,typed Ipconfig/all and all ip are 0.0.0.0, I Tried to renew the ip by ipconfig /renew it tells THE RPC SERVER IS UNAVAILABLE.and also tried to start DHCP CLIENT in services.msc and got ERROR 1068 : the depency service or group failed to start.

View 14 Replies View Related

Cisco :: Interface Status Connected But No MAC?

Feb 18, 2011

On my Switch (3750), i have a host connected. Checked the interface status and it shows as "connected". However, when i tried checking the MAC connected to that interface, its not showingI have my Switch (3750) connected to a Router (3845). On the Switch, i have a printer connected in an interface. I am seeing the Printer's MAC associated with the switch port. However, when i checked the ARP table; no entry seen for the Printer's MAC. What are the possible reasons for this? We have several same kind of devices connected to network and they are fine.

View 5 Replies View Related

Servers :: Sync Status Is On The Device?

May 16, 2011

sync status is on the device, is what I see trying to connect to my outlook, I had to change laptops and I can't remember how to sync with outlook?

View 1 Replies View Related

Utility To Monitor A Network Status?

Jun 8, 2011

The internet connection at our business goes down overnight, every night. We then have to turn off the router and turn it back on. It is not the fault of the ISP, but some setting somewhere, either in the router (SG 310 Snapgear) or in a particular program being accessed each night. Fact is, for the time being we are just trying to find out the precise time when this happens, so we can find out a reason. Is there a utility that can monitor the status and tell you at what exact point it stopped?

View 2 Replies View Related

Why Cannot See Wireless Status On Cradlepoint Mbr1000

May 17, 2012

I have a Cradlepoint MBR1000, it has updated the firmware automatically to 2.0.0. Now I cannot see anything that is connected to it. In other words it will not show any connected equipment in the wireless status, and it will not show DHCP status. I have done a hard reboot and still don't see anything. Everything works, everyone is able to connect, but I can't see them..

View 1 Replies View Related

LAN Connection Gets Disabled By Itself On Idle Status

Feb 22, 2012

LAN connection gets disabled by itself on idle. Sometimes BSODs.A few days ago I tried connecting a MBlaze modem to my laptop (Windows 7 Ultimate 32 bit) to access internet. But it resulted in instant BSOD everytime.I deleted the modem software after that & didn't try to connect it again.But now, whenever I connect using my LAN broadband, connection works fine as long as I am continuously browsing something. But as soon as I stop browsing and it goes in idle mode in about 10-15 minutes, the connection gets disconnected. In the adapter properties, it shows that the driver is working properly. If I try to disable or uninstall it it doesn't give a response. The only solution to this is a forced shutdown & restart, after which it works fine untill not idle. I am not able to download anything because of this.I tried many things like reinstalling the network adapter driver, unchecking the power management feature, resetting the connection, etc. but nothing is working.

View 5 Replies View Related

Cisco :: 4500 Can't See Status Of Interface

Oct 27, 2012

I do terminal monitor on my 4500 switch.I can't see the status of the interface ( when it become up or down)What is the problem? I need to add a command?

View 3 Replies View Related

Cisco WAN :: 1841 EOL And EOS Status Of Devices

Jan 17, 2011

I want to use 1841 router for implementation in one project but I could not find out from where I can get End of Sale, End of Life and End of Support details for this router, any links so that I can dig out Cisco is maintaining these details at some of its portal but where.

View 10 Replies View Related

Cisco :: (WS-C3750X-24T-S) Fan Status Via SNMP?

Feb 24, 2013

requesting information via SNMP from my two stacked C3750X, running IOS 12.2(55)RE5. The stack is up and running and everything is just fine. There are three PowerSupplies installed with a PowerStack, also running like expectet.My problem ist to get the status-information about the chassis-fans. I couldn't find any information about the OID and the search results only in some non-useful information about the MIBs from Cisco which delivers only three information about installed fans (and fan-containers), so I guess these are the information about the fans included within the powersupply?! The chassis-fans are installed and the LEDs are green for all four fan-mounts, up and running.

View 4 Replies View Related

Cisco AAA/Identity/Nac :: ACS 5.1 With AD - Status Is Disconnected

Feb 23, 2011

I have a number of users who are failing wireless authentication. Using the troubleshooter i notice that its show message that Active Directory servers are not available. Under the Identity stores when i check on the connection status it shows disconnected. When i click on Test connection it shows successful. This ACS is a secondary. It has happened before and i removed it from the ACS cluster, rebooted it and rejoined it. Ran test connection and it showed "CONNECTED". Now it keeps showing disconnected.

View 6 Replies View Related

Cisco AAA/Identity/Nac :: What Is The Use Of Status Field In ACS 5.3

Aug 7, 2012

users whose status is manually disabled don not have difficulty in authenticating and access managing nework devices. that makes me wonder what is the difference between status enabled and disabled?

View 44 Replies View Related

Cisco WAN :: To Check Status Of VPN 1841

Dec 15, 2010

i have a router 1841 series and LMS send me  amessage telling me the VPN AIM is not working on thsi device and i want to check the status of this VPN card

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved