Cisco Wireless :: Wireless Power Injector For Aironet 1250
Sep 3, 2012I have a cisco wireless power injector for Aironet 1250 but I called Cisco and was told this can't be found in the system.
View 9 Replies
ADVERTISEMENT
Cisco Wireless :: Normal Boot Time For Aironet 1130AG With Power Injector?
Jun 1, 2012I have installed an Aironet 1130AG and utilized a power injector for the power source. I have the settings configured correctly in IOS, but the AP takes about 7 minutes to come on (illuminate LED status lights) once the Ethernet cable is connected. Is this 7 minute power-on delay normal when using POE? I am used to the instanteous "on" that usually comes with Cisco products being connected directly to the AC adapter.
View 5 Replies View RelatedCisco Wireless :: Aironet 1410 Bridge Power Injector Coax Cable Length Limits?
Apr 19, 2011how far apart an Aironet 1410 Bridge can be from the Power Injector (Dual Coax feeds). I just can't find the specification details. The device comes with a 20' and 50' F-type and I'm looking at 150' runs for both ends of the bridge pair.
View 2 Replies View RelatedCisco Wireless :: 1252 - WCS Reports AP Draws Low Power - With Correct Power Injector
Jul 21, 2011I keep getting alerts from our WCS stating that our 1252s are drawing low power. Now I am aware that they require enhanced PoE (up to 20W) but as we only have standard PoE in that building we purchased the 1252 series power injectors to go with them.
However, even with the correct power injectors the WCS still reports the draws low power error.
Is this a bug? Running WCS 7.0.172 at the moment.
Forgot to say we are using the PWR-INJ4 and the injector status is enabled and you see the injector MAC address when you drill in to the AP status.
Cisco Wireless :: Aironet 1250 With 2x 2.4Ghz Antenna?
May 7, 2012I need to upgrade a 1230 to the new Aironet 1250 at a location. I have only 2 external antennas at that location.
I understand that you still can run 802.11n with 2 antennas. But I can not find anywhere in WLC 5508 v7.2 that I can disable the middle nut (C)
Cisco Wireless :: Lost Web Access On Aironet 1250
Dec 29, 2012I can no longer open a http or https connection to the AP. I do have ssh access and I can log in with full privileges.
I was using the Web interface a few days ago and it did something strange during an update. The display of the web page became corrupted and no longer responded to my input.
I restarted it from an ssh session and I have also power cycled it via the power injector. Neither method has worked.
What should I do next or what additional info can I provide from an ssh shell?
Physical access is very difficult. It requires a 30' ladder after 10 p.m. So, I would like to avoid that if possible.
Cisco Wireless :: Power Injector For WAP 4410N
Jun 28, 2011I need a power Injector compatible for WAP 4410N.
View 3 Replies View RelatedCisco Wireless :: Aironet 1250 LWAPP To Autonomous Downgrade?
Aug 25, 2010upgraded my home AP from Autonomous to Lwapp. I was an Idiot and thought i was getting an IOS upgrade. I need to revert it back to autonomous and a simple "mode" button reset doesnt work. I read that I need to Reload original IOS software, but It appears I cant get it without a support contract. I cant afford servicenet and need to obtain old ios to revert to factory default 12.4(10b)JA1. Do I need a contract to roll back? Is there an archive (backup image) of the old IOS that could be still stored on the device. I didnt back it up and need to obtain the image.
View 5 Replies View RelatedCisco Wireless :: Power Injector Compatible With 541n AP?
Aug 2, 2011if the Cisco Power Injector (AIR-PWRINJ3=) is compatible with the 541n AP ? I find info about compatility with other AP models but didn't find any related with this SMB model.
View 2 Replies View RelatedCisco Wireless :: Power Injector For 1310 Bridge
Apr 11, 2013We have a failed power injector on a 1310 series bridge. Will the "Power Injector LR" from a 1410 series bridge work on the 1310?
View 1 Replies View RelatedCisco Wireless :: Cannot Find Power Injector For Wap2000
Jan 12, 2011Not long ago i was bought Cisco wap2000 access point for small business, and now the problem is to find power injector for this device. I am already tried to use AIR-PWRINJ3, but access point did't turn on.
View 7 Replies View RelatedCisco Wireless :: 1602i APs - Power Injector Or Adapter?
Jan 28, 2013We are planning a wireless network using the 1602i APs. Some of our APs might or might not be within the 100m limit from the switches, so we'll be running them as repeaters instead. Right now, we are planning on buying power injectors for everything, but I can't seem to find an answer to this question:
If I'm running an AP as a repeater (no ethernet running back to a switch), can it still receive power from a power injector and a short ethernet run between the injector and the AP? Or will I need to use a power adapter?
Cisco Wireless :: Power 1552e With Proper Poe Injector?
Oct 13, 2012Can I power the 1552e with the proper poe injector if I am not using the ethernet port for backhaul? I want to get power thru poe but use a fiber for backhaul.
View 4 Replies View RelatedCisco Wireless :: Aironet 1250 AIR-LAP1252AG-A-K9 - Change To Autonomous Mode
Jun 11, 2013I have an Aironet 1250 AIR-LAP1252AG-A-K9 I am having issues with, and I am hoping for some direction on how to resolve them. I understand this question has been posted many times many different ways, but i have no luck unfortunately. Here is where I am: I can terminal into the AP, which has been set to factory default, with the username and password and enable password of Cisco. Once I am in the enable mode, I get lost.
Usually there would be an option to go to config. t, and work from there, but this AP does not have that option, Actually if I do a ? at the enable prompt, the commands list only starts with the letter C; but none are config.
I also cannot get into the web interface of the AP. The AP gets a DHCP IP from my DHCP server, (192.1681.128/24) but I cannot get into the web interface using the IP it gets from DHCP. The page never comes up. To add to the confusion, I cannot turn off the CLI event logging, although I enter the command "no debug all". Maybe I am off on what to put in. Nonetheless, it drives me crazy with messages every two seconds as I am trying to type while attempting to figure things out.
Overall, from reading the forums and doing Google searches, I am going on the assumption that the AP is now in lightweight mode, as opposed to autonomous mode, which is where I want it to be. I have tried the method of updating the firmware to the autonomous firmware from Jan 2013 for the AP. I use the TFTP method as I have found here on the forums a few times; I hold the mode button down while applying power to the AP, let the system LED turn red and release the button so the TFTP process can go through, but nothing changes.
I have the AP powered from a gigabit POE switch. The computer I am using for the TFTP is on the same sub net as the AP. I have tried using 10.0.0.6/24 for the computer with the TFTP on it, made sure the view all file extensions option was checked, and renamed the firmware to the .default extension-still nothing updates.
I also noticed that once I hold the mode button down for 20-30 seconds then let it go, the CLI output says the AP it is on the 10.0.0.x sub net, but I cannot ping the computer with the TFTP program on it. If i try to, it get a "Command not supported" message. So I will go on the idea that this is most likely why I cannot do a TFTP update.
About 30 seconds after I release the mode button and the AP boots, it will say it has a 10.0.0.x IP address, then it starts going crazy with messages that it cannot find a DHCP server.
Cisco Wireless :: WAP4410 Doesn't Just Make A Universal Power Injector
Oct 10, 2011Contrary to the information contained in the link above, these two parts do not play well together. I purchased both and plugged them in and no go. It doesn't even light anything on the WAP. It worked fine when it was on its own 12V DC adapter but not plugged into this injector. What I don't understand is why Cisco doesn't just make a Universal power injector that is essentially a 1 port switch and is 802.3af or 802.3at compatible. Its maddening. It looks like I'm going to have to get an SD208P and waste 6 ports just to get one with the correct POE for the WAP4410.
View 2 Replies View RelatedCisco :: WEP Key In Aironet 1240 / 1250
Mar 8, 2011In a multiple SSID setup, can Aironet 1240 & 1250 series AP supports different WEP key for different SSID
View 3 Replies View RelatedCisco :: Aironet 1250 Overlapping Channels / COM-AP Loses Connectivity
Jan 13, 2012In my LAN, I have always been used an Aironet 1250 for internal use and always work fine. Now, I added a 3com AP but both AP are not correct. When I turned off the AIRONET 1250, the 3COM AP settings works fine. When both are turn on, the 3COM AP loses connectivity all the time.I have heard about the overlapping channels in 802.11b/g networks.
View 8 Replies View RelatedCisco Wireless :: Power Cycle Aironet 1242ag WAP Often?
Nov 14, 2012I'm having a little issue with some Cisco Aironet1242ag WAP's. I receive a call at least twice a month stating that some of the WAP's are not giving out internet connection. What I always do is go to my patch panel and disconnect those WAP's not working and connect them back again so they can power cycle. These WAP's are connected to a Cisco3750g. Once the WAP's boot up, the users can connect to the WAP and connect to the internet.
I don't know if these WAP's are filling up with some information that causes the access points to not connect to the WAN.
Cisco Wireless :: Is It Possible To Lower Power Draw On Aironet 1552e AP
Mar 20, 2013Is it possible to lower the power draw on the Aironet 1552e AP (AIR-CAP1552E-N-K9) so it will run on a standard PoE device (IEEE 802.3af). The spec sheet for the AP says you need to either use the Cisco PoE injector (AIR-PWRINJ1500-2=).Is there possibly a firmware upgrade/downgrade or some sort of command I can use?The APs being used are running LWAPP and require a controller.
View 2 Replies View RelatedCisco Wireless :: WAP4410n With POE Injector
Nov 14, 2011We are looking at purchasing two of the WAP4410n Access Points to add wireless in one building, and possibly replace Wireless G in another. In our building already configured, we have POEs set up and this has worked to centralize everything that has to be monitored. We would like to do the something with the WAP4410n. With the access points we already have, they are Pre POE so there was only one device that would work. With These they are standard POE, Does that mean I can use any POE Injector that is using this standard?
Also, are problems that first existed these access points being worked out or been fixed? I want these to be minimal attention required since I am the IT person here and I don't work in this building, I work in the other building which is walking distance but I do want to avoid problems if possible.
Cisco Wireless :: WAP4410N POE - Injector Or Splitter
Apr 13, 2011Can the WAP4410N accept a 48 VDC input from an IEEE 802.3af POE injector or is a splitter required on the AP end to drop the 48 VDC to 12 VDC and utilize the DC input connector on the back of the AP? I would prefer to use only the injector at the switch if the AP can accept the 48 VDC at the ethernet port.
View 3 Replies View RelatedCisco Wireless :: AP541N What POE Injector Are Supposed To Be Used
Jan 30, 2011AP541N wireless AP, what POE injector are you supposed to use?The web site states any enterprise class af POE injector will do, but the AP1131 POE injector does not work with the AP541N.
View 5 Replies View RelatedCisco Wireless :: Loading An Autonomous OS On A 1250
Nov 14, 2012When have downloaded the c1250-k9w7-tar.152-2.JA.tar and attempted to load into a 1250 via tftp the process aborts with the following message. [code]
View 2 Replies View RelatedCisco Wireless :: Status Led AP 1250 Lightweight?
Sep 16, 2012a few day l have 3 AP Ligthweight 1250, today l was checking my infrastructure and l saw that these 3 AP can´t join to the controller, l reset the AP to the, and its can not join, l checked physicly the AP, and the Ethernet Led is in Amber permanent and the Radio Led is in Green permanet , i am searching the status led to find the fix but l have not found these convination led. and l can not access to the consolo port.
View 2 Replies View RelatedCisco Wireless :: Radios On 1242AG Stay Down With Injector And Cat6509
Apr 18, 2012i noticed that the 1242AG does not bring up the Radios, when there is a Power Injector connected.I see in the Logs of the AP:
%CDP_PD-2-POWER_LOW: All radios disabled - NEGOTIATED WS-C6509 <Switchport MAC Add>
The Module in the 6500 is a WS-X6348-RJ-45 The Option "Power Injector installed" on the WLC is also enabled, with the MAC Address from the Switchport, but no change.When i disable CDP on the mentioned Switch Port and reload the AP, it comes up and runs fine.
Cisco Wireless :: 1250 Dipole Antenna Spacing
Apr 3, 2008When using dipole antennas such as AIR-ANT 4941 with the 2.4 Ghz 1250 AP, must the antennas be spaced EXACTLY as far apart as the antenna connectors on the AP, or can the dipoles be spread further out, say to 4" spacing.
View 20 Replies View RelatedCisco Wireless :: Controller Dot11radio 0 Not Present In AP 1250?
Oct 20, 2011I've just got a new AP 1250 series, and I was trying to configure the Radio for the 2.4Ghz spectrum using the interface dot11radio 0 and I've just noticed that this controller is not present so I cannot configure it so I wonder is it could be a HW problems as it looks to me or there is another way to enable this.
I never have an issue like this before so I want to first check with you before going back to our vendor.
Here is some of the details I get from the AP itself:
System image file is "flash:/c1250-k9w7-mx.124-10b.JDA3/c1250-k9w7-mx.124-10b.JDA3"
ap02#sh controllers dot11Radio 0 ^% Invalid input detected at '^'
[Code].....
Cisco Wireless :: Dipole And Monopole Antenna With 1250 AP
Mar 20, 2012I have a customer using 1250 AP with monopole antenna, he face frequent disconnection for voice clients during roaming. Phone is forced for reregistration to call manager during the hand off. Same customer has dipole antenna in a different floor with 1250 AP and there is no issue observed for voice clients.
Is this an issue with monopole antenna ? Which is the best antenna to recommend for Cisco APs or wht is the occasion I need to use a dipole or monopole antenna ? How to understand the difference between them.
Cisco Wireless :: 1250 AP - How Many SSID Can Be Created In 4404 Controller
Jul 7, 2011How many SSID can be create in a 4404 controller and also in standalone 1250 AP? How many VLANs can be created in eac one?
View 2 Replies View RelatedCisco Wireless :: 4400 Series Controller Blocking 802.11a/n Radio Interface Of 1250 AP
Dec 19, 2009We are facing an issue with a customer where a Cisco 4400 Series controller is blocking the 802.11a/n Radio Interface of a 1250 AP. The radio shows as down on the controller GUI. The error message on the GUI is that the 'Regulatory Domain' is not supported. This can be seen from the attached screenshot. Also relevant parts of the WLC configs are attached. WLC: Cisco 4402 WirelessWLC Country: SADevice: Cisco Lightweight Access Point 1250 (LAP) is controlled through the 4402 Cisco Wireless LAN Controller (WLC)The operating system version of the LAP: c1250-k9w8-mx.124-18a.JA version of the WLC: Software Version 5.2.178.0 The problem is that the controller shows that the 802.11a/n Radio Interface in Radio Slot # 1 is always down , the customer tried to manually 'no shut' the AP interface from the console and it worked , but obviously this solution would not work as the configuration cannot be saved (LW AP).
View 12 Replies View RelatedCisco :: 1230 / 1240 / 1250 - Web Based Registration For Guest Wireless Access
Mar 6, 2011I just started a project to make a guest wireless network available at every site in my enterprise. Guest wireless networks are currently available at some sites. Two key goals of this project is to enable WPA/WPA2 encryption and to develop a web based registration/autentication solution. All of the sites have a mixture of 1230, 1240, and 1250 autonomous access points. What do I need to do/get in order to make this happen?
View 3 Replies View RelatedCisco :: Finding PoE Injector For WAP4410N?
Aug 26, 2010I bought 2 WAP4410N wireless routers but it did not come with a PoE injector. We do not have a PoE capable switch. I have a couple of 3COM PoE injectors but am concerned about differing PoE standards could cause the 3Com PoE injector to damage the WAP4410N.
I cannot find a PoE injector on the Cisco website. What is the Cisco part number for a PoE injector for the Cisco WAP4410N or provide assurances about the 3COM PoE that I have for the 3COM 3CRWER100-75 access points?
Cisco Wireless :: Aironet 1252 / Actual Wireless Link Speed Low
Nov 8, 2012I have 2 cisco Aironet 1252 setup as a point to point link using an external antenna (one radio is setup as the root bridge the other is setup as the non-root bridge). Now I see that the connection between the radios is established at a speed of 54 Mbps. However when I perform a speedtest on the link I see that the my actual download speed does not exceed the 2,5 Mbps. what can cause my actual speed to be far lower than the 54 Mbps? And what can I do to improve it?
View 16 Replies View Related