Cisco Wireless :: Controller Dot11radio 0 Not Present In AP 1250?
Oct 20, 2011
I've just got a new AP 1250 series, and I was trying to configure the Radio for the 2.4Ghz spectrum using the interface dot11radio 0 and I've just noticed that this controller is not present so I cannot configure it so I wonder is it could be a HW problems as it looks to me or there is another way to enable this.
I never have an issue like this before so I want to first check with you before going back to our vendor.
Here is some of the details I get from the AP itself:
System image file is "flash:/c1250-k9w7-mx.124-10b.JDA3/c1250-k9w7-mx.124-10b.JDA3"
ap02#sh controllers dot11Radio 0 ^% Invalid input detected at '^'
[Code].....
View 3 Replies
ADVERTISEMENT
Jul 7, 2011
How many SSID can be create in a 4404 controller and also in standalone 1250 AP? How many VLANs can be created in eac one?
View 2 Replies
View Related
Dec 19, 2009
We are facing an issue with a customer where a Cisco 4400 Series controller is blocking the 802.11a/n Radio Interface of a 1250 AP. The radio shows as down on the controller GUI. The error message on the GUI is that the 'Regulatory Domain' is not supported. This can be seen from the attached screenshot. Also relevant parts of the WLC configs are attached. WLC: Cisco 4402 WirelessWLC Country: SADevice: Cisco Lightweight Access Point 1250 (LAP) is controlled through the 4402 Cisco Wireless LAN Controller (WLC)The operating system version of the LAP: c1250-k9w8-mx.124-18a.JA version of the WLC: Software Version 5.2.178.0 The problem is that the controller shows that the 802.11a/n Radio Interface in Radio Slot # 1 is always down , the customer tried to manually 'no shut' the AP interface from the console and it worked , but obviously this solution would not work as the configuration cannot be saved (LW AP).
View 12 Replies
View Related
Jun 12, 2012
I've been having some problems with my Ethernet connection lately.I unplugged my laptop from the Ethernet connection I had at my old place.At two different locales, I have tried to use an Ethernet connection in order to get better speed (the wireless at the first locale was non-existent and at the second it is extremely slow in my room). I have done so with two separate cables that I have tested on others' computers and found that they are perfectly fine. That, of course, leads me to believe that it is my computer and is either a hardware or software problem (here's hoping it's the latter).Anyway, my laptop is a Dell Inspiron 1720 (purchased in 2006). About a year ago, I updated to Windows 7 from the pre-installed Vista. Never had any problems (as I said, everything was fine up until about a week ago). The installed card is a Broadcom 440x 10/100 Integrated Controller. Everything under Device Manager indicates that the hardware is working properly and has all of its drivers installed, but nothing is working.I have tried to uninstall and re-install the drivers (albeit by allowing windows to find them automatically), but the result is the exact same.I have checked the port and found that there is no debris or obstructions. My computer hasn't been dropped or mishandled in any way.I'm currently being housed on the campus of Delta State University, which is why this appears, but here is the report: [code]
View 5 Replies
View Related
Jul 29, 2008
How to reset the Dot11Radio?I have also try to config the power level but it prompt me that the selection is invalid. [code]
View 10 Replies
View Related
Nov 29, 2012
This is regarding an issue with one of my access point. The access point 1252 is autonomous one running the IOS version C1250 Software (C1250-K9W7-M), Version 12.4(10b)JDA3, RELEASE SOFTWARE (fc1)
The status of the dot11Radio 0 interface is showing as RESET. I have pasted the interface brief details below.
ap03#
ap03#
ap03#sh ip int brief
[Code].....
View 10 Replies
View Related
Nov 14, 2012
When have downloaded the c1250-k9w7-tar.152-2.JA.tar and attempted to load into a 1250 via tftp the process aborts with the following message. [code]
View 2 Replies
View Related
Sep 16, 2012
a few day l have 3 AP Ligthweight 1250, today l was checking my infrastructure and l saw that these 3 AP can´t join to the controller, l reset the AP to the, and its can not join, l checked physicly the AP, and the Ethernet Led is in Amber permanent and the Radio Led is in Green permanet , i am searching the status led to find the fix but l have not found these convination led. and l can not access to the consolo port.
View 2 Replies
View Related
Apr 3, 2008
When using dipole antennas such as AIR-ANT 4941 with the 2.4 Ghz 1250 AP, must the antennas be spaced EXACTLY as far apart as the antenna connectors on the AP, or can the dipoles be spread further out, say to 4" spacing.
View 20 Replies
View Related
May 7, 2012
I need to upgrade a 1230 to the new Aironet 1250 at a location. I have only 2 external antennas at that location.
I understand that you still can run 802.11n with 2 antennas. But I can not find anywhere in WLC 5508 v7.2 that I can disable the middle nut (C)
View 3 Replies
View Related
Mar 20, 2012
I have a customer using 1250 AP with monopole antenna, he face frequent disconnection for voice clients during roaming. Phone is forced for reregistration to call manager during the hand off. Same customer has dipole antenna in a different floor with 1250 AP and there is no issue observed for voice clients.
Is this an issue with monopole antenna ? Which is the best antenna to recommend for Cisco APs or wht is the occasion I need to use a dipole or monopole antenna ? How to understand the difference between them.
View 2 Replies
View Related
Dec 29, 2012
I can no longer open a http or https connection to the AP. I do have ssh access and I can log in with full privileges.
I was using the Web interface a few days ago and it did something strange during an update. The display of the web page became corrupted and no longer responded to my input.
I restarted it from an ssh session and I have also power cycled it via the power injector. Neither method has worked.
What should I do next or what additional info can I provide from an ssh shell?
Physical access is very difficult. It requires a 30' ladder after 10 p.m. So, I would like to avoid that if possible.
View 7 Replies
View Related
Aug 25, 2010
upgraded my home AP from Autonomous to Lwapp. I was an Idiot and thought i was getting an IOS upgrade. I need to revert it back to autonomous and a simple "mode" button reset doesnt work. I read that I need to Reload original IOS software, but It appears I cant get it without a support contract. I cant afford servicenet and need to obtain old ios to revert to factory default 12.4(10b)JA1. Do I need a contract to roll back? Is there an archive (backup image) of the old IOS that could be still stored on the device. I didnt back it up and need to obtain the image.
View 5 Replies
View Related
Feb 25, 2012
This is a friend's computer, who bought it yesterday Acer desktop Windows 7 premium 64 bit. He asked me for assistance in setting it up, and I did that . IE8 and Mozilla Firefox were working. Later in the evening, he called and said that his computer had no internet access, though the laptop he had was working. This morning, I wnet to his place, reset the model and the router, and it was working fine. He called now and said that it is not working again. The service provider did not find any fault with the connection.
View 6 Replies
View Related
Jun 11, 2013
I have an Aironet 1250 AIR-LAP1252AG-A-K9 I am having issues with, and I am hoping for some direction on how to resolve them. I understand this question has been posted many times many different ways, but i have no luck unfortunately. Here is where I am: I can terminal into the AP, which has been set to factory default, with the username and password and enable password of Cisco. Once I am in the enable mode, I get lost.
Usually there would be an option to go to config. t, and work from there, but this AP does not have that option, Actually if I do a ? at the enable prompt, the commands list only starts with the letter C; but none are config.
I also cannot get into the web interface of the AP. The AP gets a DHCP IP from my DHCP server, (192.1681.128/24) but I cannot get into the web interface using the IP it gets from DHCP. The page never comes up. To add to the confusion, I cannot turn off the CLI event logging, although I enter the command "no debug all". Maybe I am off on what to put in. Nonetheless, it drives me crazy with messages every two seconds as I am trying to type while attempting to figure things out.
Overall, from reading the forums and doing Google searches, I am going on the assumption that the AP is now in lightweight mode, as opposed to autonomous mode, which is where I want it to be. I have tried the method of updating the firmware to the autonomous firmware from Jan 2013 for the AP. I use the TFTP method as I have found here on the forums a few times; I hold the mode button down while applying power to the AP, let the system LED turn red and release the button so the TFTP process can go through, but nothing changes.
I have the AP powered from a gigabit POE switch. The computer I am using for the TFTP is on the same sub net as the AP. I have tried using 10.0.0.6/24 for the computer with the TFTP on it, made sure the view all file extensions option was checked, and renamed the firmware to the .default extension-still nothing updates.
I also noticed that once I hold the mode button down for 20-30 seconds then let it go, the CLI output says the AP it is on the 10.0.0.x sub net, but I cannot ping the computer with the TFTP program on it. If i try to, it get a "Command not supported" message. So I will go on the idea that this is most likely why I cannot do a TFTP update.
About 30 seconds after I release the mode button and the AP boots, it will say it has a 10.0.0.x IP address, then it starts going crazy with messages that it cannot find a DHCP server.
View 3 Replies
View Related
Sep 3, 2012
I have a cisco wireless power injector for Aironet 1250 but I called Cisco and was told this can't be found in the system.
View 9 Replies
View Related
Mar 6, 2011
I just started a project to make a guest wireless network available at every site in my enterprise. Guest wireless networks are currently available at some sites. Two key goals of this project is to enable WPA/WPA2 encryption and to develop a web based registration/autentication solution. All of the sites have a mixture of 1230, 1240, and 1250 autonomous access points. What do I need to do/get in order to make this happen?
View 3 Replies
View Related
Sep 7, 2011
I am trying to copy a setup from a Nortel IAX100 where the carrier provides two ATM PVC's over ADSL - one for voice (VoIP) and one for data (IP). Relevant lines from the backup of the IAX's configuration include the following for the PPP authentication over the voice circuit:
<wan_8_32>
<entry1 vccId="1" conId="1" name="Voice" protocol="PPPOE" encap="LLC" firewall="enable" nat="enable" igmp="disable" vlanId="-1" service="enable" instanceId="1509949441"/>
</wan_8_32>
<pppsrv_8_32>
<ppp_conId1 userName="" password="" serviceName="" idleTimeout="0" ipExt="disable" auth="auto" useStaticIpAddr="0" localIpAddr="255.255.255.255" />
</pppsrv_8_32>
The null username and password for the PPP connection have me a bit stumped. Does the PPP connection not use any authenetication at all? (Is that possible/likely? How could I deubg it?) Or does does the IAX100 supply a chap/pap response with null credentails? (If so, how would I duplicate that using an instruction to a dialer interface?I am configuring an 877 with 12.4T and advanced IP services.
View 11 Replies
View Related
Nov 21, 2011
I hav e a 3750X Cisco Switch (WS-C3750X-48T-S) It is two Ethernet base SFP installed and working fine at slot 1 & 2, Now i am trying to install GLC-SX-MM in 3rd and 4th slot, but its not coming up, showing not present?
Gi1/1/1 connected trunk a-full a-1000 10/100/1000BaseTX SFP
Gi1/1/2 connected trunk a-full a-1000 10/100/1000BaseTX SFP
Gi1/1/3 notconnect 1000 auto auto Not Present
Gi1/1/4 notconnect 1 auto auto Not Present
image i am using is
C3750E-UNIVERSALK9-M
View 6 Replies
View Related
Oct 4, 2011
The is VLAN id setting in some network/LAN interface .... how can I ping this lan/network interface in XP ..any freeware can do it ???
View 1 Replies
View Related
Dec 6, 2012
I am receiving this error after connecting a copper adapter on a GBIC blade in a 6509. Here are the results from the show Interface. I am waiting to confirm the device on the other side settings but as far as I see I get UP and Up for protocol and line respectively.
GigabitEthernet2/11 is up, line protocol is up (connected)
Hardware is C6k 1000Mb 802.3, address is 0009.11e4.f3ce (bia 0009.11e4.f3ce)
Description: RCPBSDEV
MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
[code]....
View 3 Replies
View Related
Sep 13, 2011
I an currently running Cisco (ACS 5.2.0.26.3) and attempting to get my Cisco 5508 WLC's (7.0.98.0) loaded into ACS for TACACS+ authentication for managment users.
However I keep getting the following error:
*emWeb: Sep 14 14:44:45.931: %EMWEB-1-LOGIN_FAILED: ews_auth.c:2104 Login failed for the user:test_tac. Service-Type is not present or it doesn't allow READ/WRITE permission.
Now I've attempted the step-by-step using the following URL but to no avail.( there are some slight differences in ACS 5.2)
[URL]
Latest WLC configuration guide I could find (Software Release 7.0 June 2010) isn't much useful either.
View 6 Replies
View Related
Apr 10, 2013
I have a peculiar issue with a router whering I get the message in the Show Environment as below.
sh environment out
Redundant Power System is not present.
SYS PS1 is present.
Type: AC
AUX(-48V) PS1 is absent.
Fan 1 OK
Fan 2 OK
Fan 3 OK
Fan Speed Setting: Normal
Alert settings:
Intake temperature warning: Enabled, Threshold: 55
Core temperature warning: Enabled, Threshold: 70 (CPU: 95)
Board Temperature: Normal
Internal-ambient temperature = 22, Normal
CPU temperature = 37, Normal
Intake temperature = 22, Normal
Voltage 1(3300) is Normal, Current voltage = 3300 mV
Voltage 2(5150) is Normal, Current voltage = 5210 mV
Voltage 3(2500) is High/Low, Current voltage = 2168 mV
[Code]...
View 4 Replies
View Related
Mar 8, 2011
In a multiple SSID setup, can Aironet 1240 & 1250 series AP supports different WEP key for different SSID
View 3 Replies
View Related
Aug 12, 2012
I know that the 3600 series APs are not supported on the 4404 WLC. However, would the following scenario be supported? I would like to use the 4404 (software rel. 7.0) as a guest anchor with a 5508 (software release 7.2) as the foreign controller supporting series 3600 APs. I ask because the APs do not need to join the guest anchor.
View 7 Replies
View Related
Jun 2, 2013
We have a customer that have 2 5508 as primary and backup controller and a 4400 as an anchor controller. We plan to upgrade the 5508 to 7.3.112.0 and the 4400 is already 7.0.116.0. Will there be any issue if the anchor controller is not the same code as the foreign controller? Do I also have to upgrade the acnhor controller to 7.0.240.0?
View 2 Replies
View Related
Mar 31, 2013
We are trying to navigate the waters in choosing between a in-house, controller-based, wireless network solution or a cloud-based solution. We have been presented with the usual suspects in cloud-based (Aerohive, Meracki, etc) and with Cisco (5500) and Aruba on the other side. We are a multi-campus organization with approx. 200 APs.Any hard reasons why go with a controller-based vs. cloud-based solution? If we must keep the conversation limited to Cisco, why go Meracki over Cisco's WLC solutions or vise versa?
View 1 Replies
View Related
Dec 6, 2012
I am looking to configure a wired and wireless guest network. I have industrial barcode scanners that connect to one SSID and then there is the business network on the office SSID (no vlan seperation for these devices just different SSIDs). There is not really a need to seperate the business network from the scanners in any case. However, there are needs for a guest network and this needs to be seperated. At the bare minumum I would like to have the wireless guest network. Here is what I have: 2125 Wireless LAN controller managing 18 LAPs (1 indoor and 17 outdoors)Cisco Cat 2950 switches (2 x 24 port and soon to be replaced with 2 x 48 port 2960's with 802.1x capability) Sonicwall TZ210 firewallOne existing wired and trunked vlan for PLC infrastructure. One ESXi hosting Windows server guests (soon to be 2 with vMotion) The reason for the wired guest access network is tp prevent anyone from plugging into the wall jack in the office with thier home laptops or anyone else from being on the same subnet as our domain machines. Granted they would be unathenticaed but there would be no layer 2 seperation and that is what I think would be best.
How would I go about doing this on the wireless controller without an anchor controller just using my existing hardware? I would like to have the Guest SSID only availible in the front office. Is it possible to offer a guest network while still servicing the business network SSID on the same access point? Then might I be able to have the guest network be treated as it should at the controller? However this might present another issue altogether as the guest traffic will be over the same wire as the business SSID until it hits the controller for management.
View 1 Replies
View Related
Aug 10, 2011
I have an Aironet 1250 Access Point. I was asked to upgrade the software on the access point so I downloaded c1250-k9w8-tar.124-23c.JA5.tar and tried to upgrade it from IE9 browser window. I allowed the upgrade to run overnight. It ran for 900+ minutes before I unplugged the router. I know it said not to interrupt the upgrade, but it seemed like something was wrong.So, I have the access point conntected to my computer with a blue cable and it is also connected to the network. I tried running Hyperterminal hoping that I could set the ip address or otherwise connect to it.
The Hyperterminal printout gives me this:
APc89c.1dfd.189a#*Aug 22 20:10:03.523: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.Not in Bound state.*Aug 22 20:10:12.027: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination.*Aug 22 20:10:12.095: %DHCP-6-ADDRESS_ASSIGN: Interface GigabitEthernet0 assigned DHCP address 159.169.59.114, mask 255.255.255.0, hostname APc89c.1dfd.189a
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (159.169.59.39) (159.169.59.25)
Translating "CISCO-LWAPP-CONTROLLER"...domain server (159.169.59.39) (159.169.59.25)
Is it possible to get this access point working again? How would I get it working again?
View 2 Replies
View Related
Mar 22, 2013
I am new to the NCS implementations and configurations. I have one very specific case with Cisco Prime Infrastructure 1.2 and autonomous APs and several issues with Cisco VSS on 6500 switches. So here is the version from Prime:
NCS/admin# show version
Cisco Application Deployment Engine OS Release: 2.0
ADE-OS Build Version: 2.0.1.038
[code]......
Well the issue what we have now is that access point has been added but its not recognized by the NCS prime. I have tried all three versions of SNMP but I get the same result. The SNMP configuration is valid since I use the same for my switching infrastructure. When I enter "debug snmp packets" and "terminal monitor" I can see the SNMP communication between Prime and Aironet 1250 which is standalone.
When I switch to Life cycle theme and go to Operate > Device Monitor Center I see all devices I have added. The Aironet 1250 is reachable but under collection status I get Managed with Warnings. When I hover over with my mouse I get "None available".
I have successfully added my switching infrastructure in total, which is operating perfectly for Catalyst 2960/3650/3750/4500 series but for 6500 under VSS I have some warnings. The device is recognized by the system which is excellent and all is operational. I get the following errors under Collection Status:
feature_sensorSNMP request timed outfeature_powerSupplyFanStatus-6kSNMP request timed outIdentityCapabilityThe device is unreachable.feature_flashdeviceSNMP request timed outsam_ipsla_featureThe device is unreachable.
What can be done to resolve these issues ? I have attached a screenshot of this particular issue. The affected access point is 172.16.165.241.
View 4 Replies
View Related
Jan 5, 2011
I have installed 4 unit Cisco Aironet 1250 acting as Autonomous AP each. I want to integrate these AP to Windows Active Directory for authentication level.
When I read configuration guide on Cisco Aironet, they must be authenticated via RADIUS server.
Is it possible that these AP directly authenticated to Active Directory via LDAP protocol?
View 4 Replies
View Related
Aug 22, 2012
I don't really know what I am doing and have had no Cisco training I have an Aironet 1250 Access Point. I was asked to upgrade the software on the access point so I downloaded c1250-k9w8-tar.124-23c.JA5.tar and tried to upgrade it from IE9 browser window. I allowed the upgrade to run overnight. It ran for 900+ minutes before I unplugged the router. I know it said not to interrupt the upgrade, but it seemed like something was wrong.
So, I have the access point conntected to my computer with a blue cable and it is also connected to the network. I tried running Hyperterminal hoping that I could set the ip address or otherwise connect to it.
[code]....
View 13 Replies
View Related
May 20, 2013
I have a aeronet 1250 access point and i have a windows 2003 radius server configured to authenticate users. I need to configure the access point for radius authentication .
View 1 Replies
View Related
