Is it possible to lower the power draw on the Aironet 1552e AP (AIR-CAP1552E-N-K9) so it will run on a standard PoE device (IEEE 802.3af). The spec sheet for the AP says you need to either use the Cisco PoE injector (AIR-PWRINJ1500-2=).Is there possibly a firmware upgrade/downgrade or some sort of command I can use?The APs being used are running LWAPP and require a controller.
View 2 RepliesWhat is the operating and/or peak power consumption (in kW) of a 5508 WLC with redundant power supplies?
The below power details are from the 5508 datasheet which lists 115 W as the maximum draw (0.115 kW) however this seems a bit low, is this right?
Input power: 100 to 240 VAC; 50/60 Hz; 1.05 A at 110 VAC, 115 W Maximum; 0.523 A at 220 VAC, 115 W Maximum; Test Conditions: Redundant Power Supplies, 40C, Full Traffic. Heat Dissipation: 392 BTU/hour at 110/220 VAC Maximum Cisco 5500 Series Wireless Controllers Data Sheet: [URL]
Can I power the 1552e with the proper poe injector if I am not using the ethernet port for backhaul? I want to get power thru poe but use a fiber for backhaul.
View 4 Replies View RelatedI am trying find out what the nominal power draw is for the following switch. The installation manual and data sheets says that the power draw for the units are 15.1W and 15.7W maximum at 18VDC. I am trying to use the switch for a solar application (12VDC) and would like to find out what the nominal draw would be when the device is in standby or if all of the ethernet ports are unused. I plan to use the two fiber SFP's and one copper port.
IE-3000-4TC
IE-3000-8TC
What is the power rating of a 1552e mesh AP before the antennas are attached? I have the dual band 2.4 / 5 GHz antennas. I know their Db rating, but I have not been able to find what the AP is.
View 1 Replies View RelatedI'm having a little issue with some Cisco Aironet1242ag WAP's. I receive a call at least twice a month stating that some of the WAP's are not giving out internet connection. What I always do is go to my patch panel and disconnect those WAP's not working and connect them back again so they can power cycle. These WAP's are connected to a Cisco3750g. Once the WAP's boot up, the users can connect to the WAP and connect to the internet.
I don't know if these WAP's are filling up with some information that causes the access points to not connect to the WAN.
I have installed an Aironet 1130AG and utilized a power injector for the power source. I have the settings configured correctly in IOS, but the AP takes about 7 minutes to come on (illuminate LED status lights) once the Ethernet cable is connected. Is this 7 minute power-on delay normal when using POE? I am used to the instanteous "on" that usually comes with Cisco products being connected directly to the AC adapter.
View 5 Replies View RelatedI have a cisco wireless power injector for Aironet 1250 but I called Cisco and was told this can't be found in the system.
View 9 Replies View Relatedhow far apart an Aironet 1410 Bridge can be from the Power Injector (Dual Coax feeds). I just can't find the specification details. The device comes with a 20' and 50' F-type and I'm looking at 150' runs for both ends of the bridge pair.
View 2 Replies View RelatedI am on BrightHouse cable internet and running a Netgear WGT624 v3 wireless router and WPA-PSK + WPA2-PSK. Computer1 is the only computer on the network at present and is connected via CAT5 cable. No wireless computers here are turned on.If I enable wireless radio, my SpeedTest (www.speedtest.net) is consistently 2- to 3 Megs slower than when wireless is turned off. I have run this comparison over a dozen times spread out over about a 14 hour period.
View 8 Replies View RelatedMy router got turned off for aroud 2 hours, now my speeds have dropped by around 40-50% according to speed test.
View 1 Replies View RelatedI am using a linksys E3000 router, and a linksys AE1000 adapter with XP system, for some reason adapter always has to reconnect, disconnect, reconnect. and even with good connection, it only has a maximum speed 144MBPS. How to reset the adapter or the router so it won't get disconnect so often and maximize the speed.
View 3 Replies View RelatedHow to draw a lan/wan diagram
View 1 Replies View RelatedI was trying to draw a diagram for my network, when the following problem occurs.When using "show cdp neighbor" command on my primary core switch i see the proper name and interface # of the attached secondary core switch. However, upon using the "show cdp neigh fa1/1 detail" command (fa1/1 is the port i get that is attached directly to the secondary core switch and is the correct int that is connected to it) i get the wrong ip!!! The ip it gives me is not that of the secondary core switch but is that of the asa firewall!! When i go on the secondary core switch and do the same thing i get the same result but it gives me the ip of the 2nd asa firewall instead.
Notes: I am logged in to the management vlan. Firewall vlan is separate as well. asa is also connected to the switches but on different ports.
1552E Rap will "lock" up, and not allow MAPs to connect through it to join. the WLC. Rebooting the Rap will resolve the issue, but the problem comes back and some random point in the future. Prior to rebooting the Rap to fix the issue, the Rap shows as joined to the WLC, but I have noticed that the neighbor details look stale, meaning my MAPs don't show up as neighbors, but other MAPs in the area are in the neighbor list, listed by MAC address. At this time, I can not confirm whether or not the neighbor detials are changing (updating), but I can confirm that my MAPs never show up as neighbors.As soon as the RAP is rebooted, MAPs join the controller again.
View 3 Replies View RelatedWe purchased cisco AIR-CAP1552E-A-K9 and it has IOS c1520-k9w8-mx.124-23c.JA2. WLC with the lastest firmware 7.0.116.0 is not able to connect to the Cisco 1552E. 1552E log show that it can see the WLC but unable to connect. We have devices for both U.S and Australia domain. Why are the 1552E not able to connect to the WLC?
View 19 Replies View RelatedI am designing a wireless mesh network for a client using several 1552 access points that will be bridged together. Only the RAP has a wired connection to their existing network. The client has informed me they want to hang switches off of the MAPs to connect existing wired devices. I found this in the install manual, "To forward bridge traffic, add a switch between the power injector and controller" but I will not be using power injectors (just AC power). Will adding a switch off of the AP's impact their wireless bridging abilities?
View 15 Replies View RelatedI can't find information about two features in 1524PS and 1552E/EU:
1. Does it have WEP encryption ?
2. Does it have SNMPv3 protocol for monitoring and remote managing ?
I guess, that software is similar in both, so answer will be the same in 1524PS and 1552E/EU.
How to confirm this features in 1524PS ?
I need to use 14Dbi patch antennas (like AIR-ANT5114P-N I use to have on AP1522) on AP 1552E. Is it possible?
View 2 Replies View Related% CDP is not supported on this interface, or for this encapsulation*Apr 2 18:35:20: %CAPWAP-3-ERRORLOG: capwap ifs: read error or timeout
[code]....
Done a wifi mesh using 1552E and 1552i mix of AP's ? With the 1552E as RAP and 1552I's as MAP's ? Is it a recommended model of deployment and will it work well ? the 1552i having radiation pattern more towards the ground when mounted on top , will the mesh backhaul to the 1552E be strong enough ?
Will this work if i put the 1552e at a lower level than the 1552i so that the mesh is formed properly ?
I've looked through the documentation for loading the autonomous image on a 1552E WAP that has the lightweight image on it. All the documentation I can find mentions using the "archive" command at the command line. It doesn't appear to like the archive command.
I've seen in the documentation that it also mentions the software is loadable through the controller, but I can't figure out how to do that.
I currently have the 1552E connected to my 5508 controllers running 7.3 software. how to load this autonomous image on to the 1552E? I'm planning on using it to do site surveys with the 1552E.
I just have a brand new Aironet 1552E , just took it out of the box and connect to the same subnet with a WLC 5508 v7.2 fully config and working However, it could not join the WLC 5508.
View 4 Replies View RelatedI connected to AP 1552E and my computer via PoE Gigabit Ethernet Port. Port is up and two of them are the same subnets.Even if my computer and ap arp table seen each other but i couldnot ping the each of them. [code]
View 4 Replies View RelatedIn our mesh network. there are 8 root AP and 15 mesh AP . we are using 1552E ,i have few questions on it:
1. If the ap's acting as mesh ap are connected with only 2.4 ghz external antenna, will they have problem joining the root access point to form mesh.
2. How should we set the channel assignments. Do we only set them in root ap's.
3. should the channels be set under 802.11a ?
4.should the channel be manually set or should it be left to be chosen dynamically.
We have an ASA5520 firewall, IOS 8.0(4), running in routed mode with an operational Cisco 2821 router to ASA-5520 L2L IPsec VPN.:All Internet searches explain how to enable a L2L IPsec VPN from the LOWER security-level interface to a HIGHER security-level interface- and this is how our setup is configured and it is operational and working fine.:We now have a need to setup another L2L IPsec VPN tunnel on the same firewall BUT this time traffic will be arriving on the HIGHER security-level interface destination is to a LOWER security-level interface.:Is it possible to enable a L2L IPsec VPN tunnel between a HIGHER security-level interface to a LOWER security-level interface?
View 5 Replies View RelatedIs Cisco WCS mandatory when deploying an outdoor enterprise mesh solution?If I am goin to use the 1552E purely as an outdoor access point ,do I really need the Cisco WCS?
View 2 Replies View Relatedrecently I installed WLC 5508 en the central office and installed a network mesh in a remote office; central and remote office is connected with serial link as WAN, and I have dhcp server in the remote office for give ip address to all users and devices in the remote office. Additional I have 5 LAP1552 (mesh) and 2 LAP1260 in the remote office, all clients that connect to LAP1260(this don't belong to the mesh) receive ip address from dhcp server, but neither client that try to connect to the mesh (LAP1552) receive ip address from dhcp server. I don't have if I doing some thing bad. The range IP that receive the all ap's belong to the network of devices and the range ip for the users belong to network of users.
View 12 Replies View Relatedwhich controller I should use with 11 1552E AP ? I know 5508 will work with the AP's, but would the 2504 also work? If 2504 will work, I will go for the 2504 since its a cheaper solution.
View 5 Replies View RelatedI have a number of 1552e APs connected to a 5508 WLC. We are using local MAC filtering to enable the 1552's to connect to the WLC.
I have a several more 5508's in different locations, and can be used for back-up in the event the primary WLC fails.I have the primary WLC, a secondary WLC and a tertiary WLC loaded into each the 1552's HA tab.
My question concerns the secondary and tertiary WLCs... do I have to load all the MAC addresses in each of those as well in order for the 1552's to connect? If yes, is there an easy way to copy the local mac filtering from the primary WLC and load it into the other WLCs ?
I have a running Mesh Network with AP 1552E and Controller 5508. The end customer has a new requirement to have a indoor coverage near to AP1552E (mesh AP). But in this building he has not any wired Network (it is far from any switched site). The question is: We can use an AP1262 indoor with Line Of Sigth to AP1552E in the running Mesh Network? I know AP1262 can be used in a Mesh Netwok (Root or Mesh) configuring it as BRIDGE [URL]
View 1 Replies View RelatedI have read that nat control is no longer exist in this version,However, I am trying to permit traffic from lower security interface to higher interface security,Is it need to be Natted ?
When I try to route, i have never succeeded, but when I put a nat, I can access and the traffic go through Do I miss anything on the nat control statement ?
I have to build a MESH topology with 1 Root Access Point and 4 Mesh Access Points which are 1552E.I have a wireless controller which is a WiSM 2 card into a 6500 chassis.I want to know if there is a pre-configuration to do on the AP before installing it, or if they are automaticaly discovered by controller (even for MESH AP which are NOT wired to LAN) ?
View 15 Replies View Related