Cisco Wireless :: Use AP1262 Indoor In Mesh Network With 1552E?
Mar 5, 2013
I have a running Mesh Network with AP 1552E and Controller 5508. The end customer has a new requirement to have a indoor coverage near to AP1552E (mesh AP). But in this building he has not any wired Network (it is far from any switched site). The question is: We can use an AP1262 indoor with Line Of Sigth to AP1552E in the running Mesh Network? I know AP1262 can be used in a Mesh Netwok (Root or Mesh) configuring it as BRIDGE [URL]
View 1 Replies
ADVERTISEMENT
Aug 8, 2012
Done a wifi mesh using 1552E and 1552i mix of AP's ? With the 1552E as RAP and 1552I's as MAP's ? Is it a recommended model of deployment and will it work well ? the 1552i having radiation pattern more towards the ground when mounted on top , will the mesh backhaul to the 1552E be strong enough ?
Will this work if i put the 1552e at a lower level than the 1552i so that the mesh is formed properly ?
View 2 Replies
View Related
Aug 10, 2011
We are looking to deploy an indoor mesh deployment in an area where radar might be an issue.know that when using 1500 series APs you cannot choose UNII-1 channels even if they are deployed indoors.My question is if you can use a UNII-1 backhaul with indoor APs (3600 series for example) in an indoor mesh deployment.
View 8 Replies
View Related
Jun 6, 2012
In our mesh network. there are 8 root AP and 15 mesh AP . we are using 1552E ,i have few questions on it:
1. If the ap's acting as mesh ap are connected with only 2.4 ghz external antenna, will they have problem joining the root access point to form mesh.
2. How should we set the channel assignments. Do we only set them in root ap's.
3. should the channels be set under 802.11a ?
4.should the channel be manually set or should it be left to be chosen dynamically.
View 1 Replies
View Related
Jul 20, 2011
Is Cisco WCS mandatory when deploying an outdoor enterprise mesh solution?If I am goin to use the 1552E purely as an outdoor access point ,do I really need the Cisco WCS?
View 2 Replies
View Related
Jan 31, 2013
recently I installed WLC 5508 en the central office and installed a network mesh in a remote office; central and remote office is connected with serial link as WAN, and I have dhcp server in the remote office for give ip address to all users and devices in the remote office. Additional I have 5 LAP1552 (mesh) and 2 LAP1260 in the remote office, all clients that connect to LAP1260(this don't belong to the mesh) receive ip address from dhcp server, but neither client that try to connect to the mesh (LAP1552) receive ip address from dhcp server. I don't have if I doing some thing bad. The range IP that receive the all ap's belong to the network of devices and the range ip for the users belong to network of users.
View 12 Replies
View Related
Mar 15, 2013
What is the power rating of a 1552e mesh AP before the antennas are attached? I have the dual band 2.4 / 5 GHz antennas. I know their Db rating, but I have not been able to find what the AP is.
View 1 Replies
View Related
Mar 21, 2013
I have to build a MESH topology with 1 Root Access Point and 4 Mesh Access Points which are 1552E.I have a wireless controller which is a WiSM 2 card into a 6500 chassis.I want to know if there is a pre-configuration to do on the AP before installing it, or if they are automaticaly discovered by controller (even for MESH AP which are NOT wired to LAN) ?
View 15 Replies
View Related
Sep 7, 2012
which controller I should use with 11 1552E AP ? I know 5508 will work with the AP's, but would the 2504 also work? If 2504 will work, I will go for the 2504 since its a cheaper solution.
View 2 Replies
View Related
Jan 21, 2013
A 1552E has a temperature gauge sensor connected to its power over Ethernet port. the port status shows line protocol as down.The cable from 1552 to the sensor has been changed twice. We can see the 1552E gig1 interface is at 1000full duplex. Is there any chance the speed is causing the problem here. it seems the 1552E doesn't allow to set different speed & remains on 1000.
View 2 Replies
View Related
Jan 15, 2012
Some days ago, I download standard IOS image for 1262 and installed, now this 1262 AP can start up without WLC. but I don't know how to recovery this AP image, and let's startup / download the image from WLC and has been managed...Is that ONLY remove the existence image ? and it's will be auto find WLC ?
View 5 Replies
View Related
Feb 2, 2012
End user has a AP1262 which at the beguinning was working fine, suddendly clients reports problems with disconnections. [code]
the version of IOS is Version 12.4(25d)JA., WPA- PSK is set,I have check this errors in cisco tools, it says about possible reasons; one of them
A failure of the Michael MIC in a packet usually indicates an active attack on your network or RF problems.For the moment I set countermeasure tkip hold-time 0 , based on some recomendations in this forum.
View 8 Replies
View Related
Nov 20, 2012
I would like to create a Mesh network using Cisco 1242 AP's running in Autonomous mode via A Channel.
View 5 Replies
View Related
May 28, 2012
I am using LINKSYS by CISCO (WRT54G2) Access point wirh out any controller or wireless control system (WCS). Is it possible to connect this AP in mesh scenario, if its possible, how about configuring in mesh mode.
View 2 Replies
View Related
Jun 19, 2012
I have a metal shop that needs wireless indoors and outdoors.
Will it work if I mount the 1262 inside with 4 indoor antennas mounted inside the building and 2 outdoor antennas mounted outside?
View 5 Replies
View Related
Apr 8, 2012
this note is from the 5508 controller config manual, does this apply to 1040 access points in a mesh network?
Note:The recommended power source for MAPs is either a power supply or power injector. PoE is not a recommended power source for MAPs.
View 2 Replies
View Related
Apr 11, 2013
By default, 802/11a/n is set for backhaul communication.Does that mean that if most of my clients are on 5ghz, Mesh network is not a preferred design to go? Reason being:- client communication on a/n radio might disturb the traffic of the whole cell and of all the MAPs that connect to the network through that MAP.
View 6 Replies
View Related
Nov 19, 2012
We need to add additional APs to working wireless mesh network (WLC 4402, 1520 series AP).
WLC 4402 supports 1550 series access points with firmware upgrade to 7.0.235.0 :
[URL]
Is AIR-CAP1552E-x-K9 with three external dual band antennas enough for 2-GHz b/g/n local access and 5-Ghz back haul?
Does 1552 Mesh AP work with 1522 Root AP?
View 1 Replies
View Related
Jul 12, 2012
Is Aironet 1260 good for indoor LWAP or CAPWAP environment? Do we need external antenna for the Aironet 1260 access point when using it indoor?
View 1 Replies
View Related
Mar 3, 2013
I've a WLC 2106 and it is running IOS version 7.0.240. I am trying to setup a wireless mesh and used the Ethernet bridge port on the MAP to extend the network. The wireless mesh works fine but I can not get the switch to work that is connected to the ethernet port on the MAP.I'm using two different Access points. I'm using a Air Cap 3502i as the RAP and a Air Lap1142N as the MAP.The switch port that is connected to the RAP and MAP is configured as the following:
switchport mode trunk
switchport trunk native vlan 2
switchport trunk allowed vlan 10,20,30,40
[code]....
The wireless mesh between the RAP and MAP works fine. I can connect a device to the MAP wirelessly and access the network with no problem but I can not get anything to work that connects to the switch that is connected to the MAP ethernet port.
View 2 Replies
View Related
Jul 5, 2012
Both the SLM2008 switch, and the AP1262n-a-k9 are currently at factory defaults. I can web into the switch from my laptop, but when I connect one of the 4 AP's I am trying to set up, the switch doesn't see it.
View 4 Replies
View Related
Mar 17, 2011
What is the difference between Indoor and Outdoor WiFi?
View 1 Replies
View Related
May 21, 2011
I have Wireless-G 2.4ghz 54Mbps (Linksys WRT54G) working perfectly short range. But have no connection when I'm in room about 80 ft from router and have doors to rooms closed. Partitions in home are concrete block, not sheetrock. Should I get a new N router? Is there a repeater or booster that will do the job? Or connect existing router to new router in other room with ethernet cable going outside then over roof of house then inside to room?
View 14 Replies
View Related
Feb 18, 2012
I need to connect 4-6 laptops in a mesh network topology. What equipment do I need (switches, hubs cable etc..) and how should I create the connection?
View 1 Replies
View Related
Aug 21, 2012
1552E Rap will "lock" up, and not allow MAPs to connect through it to join. the WLC. Rebooting the Rap will resolve the issue, but the problem comes back and some random point in the future. Prior to rebooting the Rap to fix the issue, the Rap shows as joined to the WLC, but I have noticed that the neighbor details look stale, meaning my MAPs don't show up as neighbors, but other MAPs in the area are in the neighbor list, listed by MAC address. At this time, I can not confirm whether or not the neighbor detials are changing (updating), but I can confirm that my MAPs never show up as neighbors.As soon as the RAP is rebooted, MAPs join the controller again.
View 3 Replies
View Related
Apr 10, 2012
We purchased cisco AIR-CAP1552E-A-K9 and it has IOS c1520-k9w8-mx.124-23c.JA2. WLC with the lastest firmware 7.0.116.0 is not able to connect to the Cisco 1552E. 1552E log show that it can see the WLC but unable to connect. We have devices for both U.S and Australia domain. Why are the 1552E not able to connect to the WLC?
View 19 Replies
View Related
Mar 11, 2012
I am designing a wireless mesh network for a client using several 1552 access points that will be bridged together. Only the RAP has a wired connection to their existing network. The client has informed me they want to hang switches off of the MAPs to connect existing wired devices. I found this in the install manual, "To forward bridge traffic, add a switch between the power injector and controller" but I will not be using power injectors (just AC power). Will adding a switch off of the AP's impact their wireless bridging abilities?
View 15 Replies
View Related
Apr 25, 2013
I can't find information about two features in 1524PS and 1552E/EU:
1. Does it have WEP encryption ?
2. Does it have SNMPv3 protocol for monitoring and remote managing ?
I guess, that software is similar in both, so answer will be the same in 1524PS and 1552E/EU.
How to confirm this features in 1524PS ?
View 0 Replies
View Related
Sep 18, 2012
I need to use 14Dbi patch antennas (like AIR-ANT5114P-N I use to have on AP1522) on AP 1552E. Is it possible?
View 2 Replies
View Related
Apr 1, 2013
% CDP is not supported on this interface, or for this encapsulation*Apr 2 18:35:20: %CAPWAP-3-ERRORLOG: capwap ifs: read error or timeout
[code]....
View 12 Replies
View Related
Jan 28, 2013
I've looked through the documentation for loading the autonomous image on a 1552E WAP that has the lightweight image on it. All the documentation I can find mentions using the "archive" command at the command line. It doesn't appear to like the archive command.
I've seen in the documentation that it also mentions the software is loadable through the controller, but I can't figure out how to do that.
I currently have the 1552E connected to my 5508 controllers running 7.3 software. how to load this autonomous image on to the 1552E? I'm planning on using it to do site surveys with the 1552E.
View 7 Replies
View Related
May 13, 2012
I just have a brand new Aironet 1552E , just took it out of the box and connect to the same subnet with a WLC 5508 v7.2 fully config and working However, it could not join the WLC 5508.
View 4 Replies
View Related
Nov 7, 2012
I connected to AP 1552E and my computer via PoE Gigabit Ethernet Port. Port is up and two of them are the same subnets.Even if my computer and ap arp table seen each other but i couldnot ping the each of them. [code]
View 4 Replies
View Related
