Some days ago, I download standard IOS image for 1262 and installed, now this 1262 AP can start up without WLC. but I don't know how to recovery this AP image, and let's startup / download the image from WLC and has been managed...Is that ONLY remove the existence image ? and it's will be auto find WLC ?
View 5 RepliesEnd user has a AP1262 which at the beguinning was working fine, suddendly clients reports problems with disconnections. [code]
the version of IOS is Version 12.4(25d)JA., WPA- PSK is set,I have check this errors in cisco tools, it says about possible reasons; one of them
A failure of the Michael MIC in a packet usually indicates an active attack on your network or RF problems.For the moment I set countermeasure tkip hold-time 0 , based on some recomendations in this forum.
I have a running Mesh Network with AP 1552E and Controller 5508. The end customer has a new requirement to have a indoor coverage near to AP1552E (mesh AP). But in this building he has not any wired Network (it is far from any switched site). The question is: We can use an AP1262 indoor with Line Of Sigth to AP1552E in the running Mesh Network? I know AP1262 can be used in a Mesh Netwok (Root or Mesh) configuring it as BRIDGE [URL]
View 1 Replies View Relatedis it possible to cascade a managed cisco switch with an unmanaged switch via SFP LC Modules?
View 1 Replies View RelatedBoth the SLM2008 switch, and the AP1262n-a-k9 are currently at factory defaults. I can web into the switch from my laptop, but when I connect one of the 4 AP's I am trying to set up, the switch doesn't see it.
View 4 Replies View RelatedDoes the autonomous Cisco WAP4410N Wireless-N Access Point could be managed using Cisco Works WLSE Express.
View 1 Replies View RelatedI recently upgraded to a new wireless access point with wireless N and still have the old G one. Wireless access point plugs into computer with 2nd ethernet port configured to give access point internet. Then, the computer would manage access to the network, restrictions, firewall for the access point and so on.
View 4 Replies View RelatedI am looking for a centrally managed wireless hotspot system. But the system has a few requirements. I have been looking around but so far I have not found a system that ticks all the boxes?
-The system (AP's) needs to be centrally managed (except for the internet connections, each site will use its own outgoing connection to the internet).
-The system needs to have some kind of ticket system for guest access (hotspot).
-It also needs to be able to identify employees so they can pass through without needing a ticket, everywhere they go.
I have a number of existing 1140G Access points.I now need to purchase a couple of new AP's to expand coverage and it makes sense to go with the latest N standard ones.Currently I only have standalone models and at the moment I don't have the budget to purchase a management box to allow me to get centrally managed models.
If I purchase 1140N standalone AP's now, can I convert the to centrally managed ones later? If yes, Any disadvantage in doing this?
we have a working wireless network managed by a 5508 WLC and nearly a hundred AP in different buildings. We want to integrate several apple-tv in different WLAN. We enable global multicast mode and igmp snooping on the WLC. When clients connect to these wlan airplay functionnality operates for 2 or 3 minutes max and after the airplay icon disappears on iDevices. If i want airplay to work again i need to reboot the Apple-TV but again it can't work for more than 2-3 minutes.
View 8 Replies View RelatedTrying to install the Linksys AE1000 wireless adapter on Windows 7 x64. So I follow the instructions. insert CD. Insert adapter.The i get this error:
"Linksys Wireless-N Router requires that wireless connections are to be managed by the Microsoft Windows Wireless Connection Manager. Some laptops and computers are pre-loaded with a different wireless connection manager which prevents your Valet or Linksys Wireless-N Router installation from loading. If this is the case, then you will need to disable or turn OFF the other wireless connection manager, and enable the Microsoft Windows Wireless Connection Manager instead."
What manager? This is windows 7, I'm not using any third party wireless utility so I don't understand why I'm getting this particular error. If windows wireless connection manager is off, how do I enable it?I've always managed my network setting through the Network and sharing center,I've tried:
(1) sweeping registry files before install(2) Plugging in AE1000 first and manually installing drivers
When I did this, the device shows up successfully in device manager and the driver installs smoothly, however when I go to network adapters, the AE1000 is listed as disabled. I tried enabling it but to no avail. Running the network diagnostics claims the driver doesn't work despite the fact that it installed successfully.
After several restarts and disabling/re-installations I recieve the same error.The end goal is to connect the AE1000 to a Cisco E3000 router.
I need a ≥ 8 port layer 3 managed switch. What would be the cheapest solution for this?I've been looking at some stuff like Cisco 4908G, but that only supports 1000base-X. I need something that supports the standard 1000base-T. I've also looked at a Cisco WS-C3508G-XL-EN, but correct me if I'm wrong, this is only layer 2?
View 11 Replies View RelatedHow many VLANs can be managed with the AIR-AP1252AG-E-K9 APs ? My customer wants to manage 4 VLANs, data, voice, guest and another.
View 2 Replies View RelatedBecause of licensing we want to keep some particular devices unmanaged via Inventory => Manage/Unmanage devices.But after some minutes all unmanaged set devices get back to managed. Its reproduceable many times.
View 3 Replies View RelatedI have a SG-300-20 Managed switch. I attached a picture of what I want to do. Is this possible to do? How would I go about doing it?
View 6 Replies View RelatedI'm looking for a good managed (i.e. a unit with stats and troubleshooting capabilities) fiber-to-copper media converter. I know there's plenty of "dumb" media converter choices out there, but was hoping to get one that has a console conn or the like to troubleshoot any possible issues. I'm converting between 50nm multi-mode fiber with an SC connector to 1000-bT copper.
View 6 Replies View Relatedi have a 20 story high rise condo bldg that i am providing internet service to. I have a 8 port managed network switch on the 1st floor. I have a cat6 line ran from each port to the 8 distrabution closets in the bldg.My question is this if i am using a managed switch to send the signal to the other switches, do the other switches also need to be managed? or can i use unmanaged switches at the other locations. I do not want each condo on those switches to be able to see or comunicate with the other condos on those switches. I am using 48 port switches in the 8 distrabution closets.
View 5 Replies View RelatedI'm looking to get a layer 3 managed switch. The HP we currently have only does layer 2.I'm looking at a HP v1910-24g. It has 24 10/100/1000 ports and looks to be layer 3 as well.It looks like they can be had for around $350.Anything different I should be looking at with similar specs? Any issues with the v1910-24g?
View 19 Replies View Relatedsuch as the SLM2048T can be configured as an managed switch. Our schools have laptop carts and we want to put switches in the carts so that the laptops will be plugged into the network when not in use and software installs, updates, etc. can be pushed to the laptops while they're in the cart instead of waiting for them to be taken out, powered on and pushed over wireless. I can find a 10/100 48-port unmanaged switch, but I really want a gigabit unmanaged switch, but they don't seem to exist so I was wondering if a managed switch can be configured and used as an unmanaged switch. I don't want to have to assign a static IP address to the switch.
View 1 Replies View RelatedI am a lucky enduser of an 3400 ME switch.i admin an 80 comp LAN with segments splitted by unmanaged layer 2 switches.Now i want ti use a 3400 me switch .I connect an ethernet cable between the console port of switch and lan computer dell server application windows 7 ethernet port.What's next?I browse the cisco site,download configuration assistent but nothing.I installed a hyperterminal and wait for call ,nothing.So,what's next?how can i give an ip to cisco swith?
View 1 Replies View Relatedhow to access the CLI mode in cisco sf 302-08p 8-port 10/100 Managed switch. I treid the every method they mentioned in the Admininstration guide.I am not able to enter the command debug-mode and comand menu after resetting the default password. After logging in, its directly guiding me to switch main menu.
View 3 Replies View RelatedI have enabled auto mode and manually included but when I run a data collection some devices don't take part in the process. When I click in show included devices I can see 19 devices in Not Managed state.
View 5 Replies View RelatedI have bought this switch to try :
We (our company) have a new glass fiber internet from a provider with 5 ip-addresses in an /29 range. I try the accomplice the following. On port 1 comes the output from the provider. On port 2 till 7 I want to separate the ip addresses so can distribute these addresses to our lan, to a wifi hotspot for external company visitors etc. So on port 2 a ip to the lan, on port 3 a ip to wifi router
I wanted to get some opinions on the topic above. We are purchasing MPLS services from a large ISP and they offer a managed router option. I will also have a Cisco ISR 2900 at each site running SRST for my voice system. I have some experience with BGP and am not scared at all to support it if need be. That said, I am currently looking at pros and cons of going with a managed router from this company vs managing my own. Actually, I will manage my own regardless and would just plug it into the managed router. My router is perfectly capable of handling the BGP protocol but I am hoping that I can get some opinions from all of you.
View 6 Replies View RelatedI get on-line, and the internet all-of-a sudden starts to show that I've downloaded my limit of 250MB. Now, I am on Hughesnet for internet service, can not get on DSL, wont happen already asked. Now, I am running a router, only way my wife and son can access the internet. They have laptops windows 7 and build-in Wireless Cards. I have a desktop windows 7. My updates are scheduled in the morning hours about 5AM so their is no reason for the computer to update. Same goes for my wife and son, their are set for early morning hours as well. I get an error message as soon as I click on my webpage that I want to browse, Internet Can Not Display The Webpage or something to that effect.
View 8 Replies View RelatedHow do i create and manage 40 user accounts on a windows 7 PC.
View 1 Replies View RelatedI have two public IP's entering a location from two different sources. One is under our control and the other is a 3rd party. Lets say Ours: 1.2.3.1 3rd Party 1.2.3.2
One is coming in through a firewall/router and the other is a direct link. Each will come into a different network segment 192.168.200.0/24 and 192.168.210.0/24
some of the hosts one subnet will need to talk to the other.
My envisioned setup would be as follows.
1.2.3.1 will come in to the firewall/router into the managed switch. 1.2.3.2 will come in the the same switch but in a vlan The vlan will have a trunked port to the firewall/router to allow routing between the vlan (192.168.210.0) and the other subnet (192.168.200.0).
Looking for support on setting up an ATM managed switch. It is a little older and void of documentation, model being Marconi ASX-200BX, that I can console but am lost from there. Much different than any Cisco switch I've ever seen.0
View 1 Replies View RelatedI just purchased a new Dell Inspiron 15R laptop. I managed to connect to other wifi access elsewhere but this particular wifi network I wish to connect to in my workplace, there is no internet connection for it.
View 3 Replies View RelatedThis is for a short temporary time until I get cisco 3560s in place. I have a 2921 configured and it is connecting to an HP non managed non VLAN switch and I cant get any traffic to pass from my computer to the router (pings or anything). Here is brief configuration that should be enough. [code]
Here are my vlans 1-default, 2-management, 192-data, 92-voice, i believe its running rapid spanning tree protocol. Do i have to take off encapsulation on my data vlan to get it to work or make the data vlan default vlan for everything. I am lost as to why this is not working.
I just purchased a new SF-300 managed switch for the purpose of using it on the DMZ, so we can mirror the internet port and monitor traffic for my company. I have set it up from the web interface to miror port 1 to port 2 and that's pretty much it. I decided to test it before putting it in production, by hooking it up to one of my core network switches, connecting a laptop to it and trying to get online. It doesn't even connect to my DHCP server to get an IP address. If I put the laptop back on the same subnet as the switch management IP, I can still connect to the switches web interface. Isn't the basic functionality of a switch to pass traffic?
I should also mention that I'm not a network engineer, so there might just be something I'm missing with regard to a default setting that needs to be switched off?
We have recently purchased SG 300-52Port Cisco Switch to support our Network but they constantly having some bizarre issues or I assume bugs, i.e. we cannot Telnet nor SSH to the switch now, whereas we were able to SSH before, we have set them up for Remote Log Services to get some syslogs and reports but no report have been generated nor logs,
I have done some testing through Wireshark and there are absolutely no reports / logs.We have some real issues with this switch and it’s hard to believe that this is a Cisco Product,
SG 300-52 Port Gigabit Managed Switch
Firmware Version (Active Image ) : 1.1.1.8
Firmware Version (Non-active ) : 1.1.0.73
Boot Version : 1.0.0.4
We are using Campus Manager 5.2 with LMS 3.2. We have 100 devices and all 100 devices has been successfully discovered in Common services in all 100 devices are showing in DCR.When we check in RME we have found all 100 devices over there.
But, in Campus Manager we got only 95 devices. out of 88 WS-C2960G-24TC-L 5 switches are not showing in Campus manager. we have added the same manully ( manually included & Ecluded all 5 devices in Campus manager) and start the data collection, but no result.
After data collection it is showing not managed by Campus Manager when we check ( Show all Included devices option).