I have enabled auto mode and manually included but when I run a data collection some devices don't take part in the process. When I click in show included devices I can see 19 devices in Not Managed state.
View 5 RepliesWe are using Campus Manager 5.2 with LMS 3.2. We have 100 devices and all 100 devices has been successfully discovered in Common services in all 100 devices are showing in DCR.When we check in RME we have found all 100 devices over there.
But, in Campus Manager we got only 95 devices. out of 88 WS-C2960G-24TC-L 5 switches are not showing in Campus manager. we have added the same manully ( manually included & Ecluded all 5 devices in Campus manager) and start the data collection, but no result.
After data collection it is showing not managed by Campus Manager when we check ( Show all Included devices option).
I am having Cisco LMS 3.2.I want to give an access to some desktop administrators so that they can pull the report of User Tracking in campus manager. Is there any way so that I can restric users to campus manager only?
View 9 Replies View RelatedUTLite33.exe from Campus Manager 3.3 does not want to start, it gives the following:
"UTLite33.exe is not a valid Win32 application".
I have the following drawback was held on autodicovery on a CiscoWorks LMS 4.0 which captured all the IP's of the devices on the network between these found a LAN segment that connects to all devices, when creating this view for the Campus Manager appears a LAN segment and We don´t want to appear there on the views, can you edit the view and delete this segment of the map. or if it is necessary to rediscover again.
View 2 Replies View Relatedthis is a device discovery issue with LMS 3.2. The devices added up in Common Services are not getting reflected under Campus Manager and Device Fault Manager. The devices are manually added and are stack switches (2960S-24TS-L).
View 1 Replies View RelatedWhen will Campus Manager support the 2960S switch series?
View 2 Replies View RelatedI have a strange problem with one switch in my LMS 3.2.1 installation.It is a WS-C3560-48TS with IOS 12.2(50)SE3 running. I have nine switches with the same type and IOS running without problems.
I notice the problem because there were no UT data for that switch. In RME and CS it was managed.Checking SNMP and config of the switch, but can't find any issues.Because at this time LMS ran in version 3.2 I installed at first CM 5.2.1 and after that the patches for CSCtd49439 and CSCtg20882.Next step was RME 4.3.1 with a lot of patches for different issues. Then I installed the patch for the internal error of CS (CSCtd07131).And finally I installed LMS 3.2.1 and patch for CSCto46927.Last step was installing the latest device packages. I did this directly from the application because it is much better handling than do a manual download. No the system seems to be fully updated.
I had the hope that CM will now find and manage this one switch. But it is still not available.I can't find the device in the data collection. But I can find it in the "Include Devices From DCR", although I configured to fetch all devices from DCR automatically to CM. To manually include the device is not working, too.
P.S. I used that step-by-step update path because it worked on two other servers very well for me.
I am working on LMS 3.2 . Tried to stop the daemon service with " net stop crmdmgtd ". It stuck on stopping state since few hours now. I can still open the application. How to terminate the previous command and restart the daemon service.
View 1 Replies View RelatedWith LMS4.0.0 and upgraded to LMS4.0.1 all devices keeps in questioning state, also after some Rediscovers.We've got SNMPv3 and v2 devices, Windows Firewall is off, RME inventory works for most of devices.All DFM processes except of DFMCTMStartup are running, its also not possible to start DFMCTM Startup using pdexec, in DFMLogServer.log you will see a lot of "ogs_server_urn" not found.
What can we do to get the devices also running in DFM?
Because of licensing we want to keep some particular devices unmanaged via Inventory => Manage/Unmanage devices.But after some minutes all unmanaged set devices get back to managed. Its reproduceable many times.
View 3 Replies View RelatedWhy this same kind of bug/error/software fault exist in LMS 4.2 as it was in LMS 3.2 ? Why after a while after discovery of devices (state is "Known") DFM drops the state of devices to "Learning" and it stucks forever. Restarting of daemon manager works for a short time. It looks like the processing of faults stops a while after discovery is complete.
LMS 4.2 is running on Solaris 10, connected to other LMS in DCR Slave configuration.
I am working with LMS 4.1 and FDM 4.1.0.
If I ask to the Supported Device Finder Portlet about C4503-E (SysObjectId: 1.3.6.1.4.1.9.1.874), it tells that this device is supported by DFM 4.1.0. Nevertheless, in DFM module each one devices appear in the "All Unknown Devices" group, with Error Code: Unsupported. CDP is enable in each one of these devices.
is it possible to cascade a managed cisco switch with an unmanaged switch via SFP LC Modules?
View 1 Replies View RelatedCustomer is running LMS 2.6.Scheduled backup was running perfect. But it is no more happening.When we checked we found that the "License Manager/ Deamon Manager is down" message pop ups.
We reset the casuser password, and then restarted the services. It becomes ok.But only the immediate backup is successful. Scheduled task fails for all those devices."License Manager/ Deamon Manager is down" happens quite often.
So instead of using 192.168.* how can I have computers on my router use my school's 152.65.*? It'd be nice for sharing things around the place. I'm just not sure a WRT54gs2 can do this as I'm not sure its software allows for such routing capabilities.
I sort of know how one would theoretically do this (I'm currently taking a networking class at school) but can I do this with a WRT-54gs2?
What ways can i connect the two building networks together(i.e best tools to use) supposing each building has a router. How will i make computer no. 10 accessible by all computers in the network.
View 1 Replies View RelatedI manage the network of a small (120 users) network spread out over 5 sites within a 10 mile radius (for normal ops- extended ops can expand to include other cities).I think I'd call that a Campus LAN, perhaps it's just a really small MAN (for normal ops)...I am starting my CCENT/CCNA track so this may be blazingly obvious to some of you- but I'm sure to learn something either way...Every now and again we have to go find "hostname "X"" for an update that won't roll out by way of our (Server Sr SysAdmin's) tools, so we actually have to put hands on it. Unfortunately the prior admins didn't document the inventory to such a level that we know "laptop_015" is in the building down by the college.
I DO have documentation on my equipment (I'm the Network Sr SysAdmin) that I have rolled together over the last 9 months being here...I have a Cisco 5520 ASA, and use ASDM to manage it. What would be extremely handy would be the ability to put a query in the system to report back what switch a given hostname is plugged intoBetter yet, if it could tell me switch and switchport.I imagine this would be simple if I had the MAC address- there's got to be a way to grep the switches for a given MAC- but not sure if it'll work in a similar fashion for ARP lookups.
I have a task to compare different approaches to implement InterVLAN routing in campus network. Google suggests only Cisco technologies for such query. But what I need is also other companies solutions (like Dell, HP etc), cost of the implementations, pros and cons.
View 1 Replies View RelatedI'm going to start the evaluation of implementing the virtualization of our campus LAN using MPLS.We'll get many inter-VLAN routing domains per VRF on the same LAN infrastructure.The LAN infrastructure is based on C6500 implementing VSS.Do you have experience with this kind of setup?Any known/faced issue that might prevent the setup of MPLS on VSS enabled C6500?
View 4 Replies View RelatedI manage a small/medium sized campus network consisting of 4 Cisco 6500 series chassis (each with SUP720's) and a couple hundred Cisco 3550/3560/2960 edge switches. We recently completed a new leg of fiber that will make a completed loop between all of the 6500's .... before I make the pyhsical connection I need to figure out my OSPF entries on each 6500 switch.
View 4 Replies View RelatedIn regards to a WAN connection, how would you recommend we connect a leased campus to our existing network. It is a temporary location that must be connected for a year.
We have an available 3845 with a VWIC2-2MFT-T1/E1 card. We are supposed to be getting 2-T1 lines from Verizon. I have a spare 3750 L3 switch for the core and 6 access switches.
I have 5 Static Ip pool all IPs are working fine. I have deploy a IIS Server on Windows2008 and configure the Static IP on that server. earlier it was working fine . but since last month the IP is not pinging from Out Side but internal IP Pool its working. I have checked the SERver firewall and another Setting is Ok. if i changed the Ip from the server the new IP is also not pinging.
View 1 Replies View RelatedHow to setup a WIFI Network in a large campus building.
View 5 Replies View RelatedI`m working on Dynamic Vlan Assigmenton the basis of end user authenticatedwhoc are part of specific AD Group in c ampus enviorment.Objective: Need to assign the vlan on switch port on the basis of authenticated users OU Group in Active Directory. Eg: There are 2 OU groups in AD, Sales and Administration. Authenticated user in Sales group should get Vlan 10 and user in Admininstration Group shoudl get Vlan 20.
Components:
Cisco 3750x/Cisco 4500
ACS Version 5.2
Microsoft AD
I need a ≥ 8 port layer 3 managed switch. What would be the cheapest solution for this?I've been looking at some stuff like Cisco 4908G, but that only supports 1000base-X. I need something that supports the standard 1000base-T. I've also looked at a Cisco WS-C3508G-XL-EN, but correct me if I'm wrong, this is only layer 2?
View 11 Replies View RelatedHow many VLANs can be managed with the AIR-AP1252AG-E-K9 APs ? My customer wants to manage 4 VLANs, data, voice, guest and another.
View 2 Replies View RelatedSome days ago, I download standard IOS image for 1262 and installed, now this 1262 AP can start up without WLC. but I don't know how to recovery this AP image, and let's startup / download the image from WLC and has been managed...Is that ONLY remove the existence image ? and it's will be auto find WLC ?
View 5 Replies View RelatedI have a SG-300-20 Managed switch. I attached a picture of what I want to do. Is this possible to do? How would I go about doing it?
View 6 Replies View RelatedWhat does the option WPA gtk-randomize State do when configuring Layer 2 Security under a new WLAN in a WLC (Code level 7.2)?
View 3 Replies View RelatedI want to configure an access RNIS with a router Cisco 1603.When I plug a cable in interface ISDN BRI with the command "ALL DEBUG EVENTS" start, I have this message : "BRI0 : changing state to F5", and after nothing. How the interface BRI 0 can arrive to State F7?
View 2 Replies View RelatedAbout 1-5 times per week I will find the jrm process showing as "Administrator has shut down this server". I have written a script that 2/day checks the status of the jrm process and if it is down, restarts it (pdexec jrm). About 25% of the time the jrm process will then show a status of "waiting to initialize". The only way I have found to recover it to shut down CiscoWorks and restart it (takes about 25 minutes). Why it would shutdown or how to get it restarted after the initializing state?
View 7 Replies View RelatedI'm looking for a good managed (i.e. a unit with stats and troubleshooting capabilities) fiber-to-copper media converter. I know there's plenty of "dumb" media converter choices out there, but was hoping to get one that has a console conn or the like to troubleshoot any possible issues. I'm converting between 50nm multi-mode fiber with an SC connector to 1000-bT copper.
View 6 Replies View Related