I am having Cisco LMS 3.2.I want to give an access to some desktop administrators so that they can pull the report of User Tracking in campus manager. Is there any way so that I can restric users to campus manager only?
View 9 RepliesUTLite33.exe from Campus Manager 3.3 does not want to start, it gives the following:
"UTLite33.exe is not a valid Win32 application".
I have the following drawback was held on autodicovery on a CiscoWorks LMS 4.0 which captured all the IP's of the devices on the network between these found a LAN segment that connects to all devices, when creating this view for the Campus Manager appears a LAN segment and We don´t want to appear there on the views, can you edit the view and delete this segment of the map. or if it is necessary to rediscover again.
View 2 Replies View Relatedthis is a device discovery issue with LMS 3.2. The devices added up in Common Services are not getting reflected under Campus Manager and Device Fault Manager. The devices are manually added and are stack switches (2960S-24TS-L).
View 1 Replies View RelatedI have enabled auto mode and manually included but when I run a data collection some devices don't take part in the process. When I click in show included devices I can see 19 devices in Not Managed state.
View 5 Replies View RelatedWhen will Campus Manager support the 2960S switch series?
View 2 Replies View RelatedI have a strange problem with one switch in my LMS 3.2.1 installation.It is a WS-C3560-48TS with IOS 12.2(50)SE3 running. I have nine switches with the same type and IOS running without problems.
I notice the problem because there were no UT data for that switch. In RME and CS it was managed.Checking SNMP and config of the switch, but can't find any issues.Because at this time LMS ran in version 3.2 I installed at first CM 5.2.1 and after that the patches for CSCtd49439 and CSCtg20882.Next step was RME 4.3.1 with a lot of patches for different issues. Then I installed the patch for the internal error of CS (CSCtd07131).And finally I installed LMS 3.2.1 and patch for CSCto46927.Last step was installing the latest device packages. I did this directly from the application because it is much better handling than do a manual download. No the system seems to be fully updated.
I had the hope that CM will now find and manage this one switch. But it is still not available.I can't find the device in the data collection. But I can find it in the "Include Devices From DCR", although I configured to fetch all devices from DCR automatically to CM. To manually include the device is not working, too.
P.S. I used that step-by-step update path because it worked on two other servers very well for me.
We are using Campus Manager 5.2 with LMS 3.2. We have 100 devices and all 100 devices has been successfully discovered in Common services in all 100 devices are showing in DCR.When we check in RME we have found all 100 devices over there.
But, in Campus Manager we got only 95 devices. out of 88 WS-C2960G-24TC-L 5 switches are not showing in Campus manager. we have added the same manully ( manually included & Ecluded all 5 devices in Campus manager) and start the data collection, but no result.
After data collection it is showing not managed by Campus Manager when we check ( Show all Included devices option).
Customer is running LMS 2.6.Scheduled backup was running perfect. But it is no more happening.When we checked we found that the "License Manager/ Deamon Manager is down" message pop ups.
We reset the casuser password, and then restarted the services. It becomes ok.But only the immediate backup is successful. Scheduled task fails for all those devices."License Manager/ Deamon Manager is down" happens quite often.
I have 3000 concentrator in 192.168.1.x/24 network (concentrator has static IP of 192.168.1.4/24 assigned to its private int). I can manage it thru HTTP from any PC in the same subnet, but connection failes while trying to connect from PC on different subnet (i.e. 10.1.1.x/24). Is there ACL in concentrator config which needs to be modified to allow management from different subnet?
View 2 Replies View RelatedAny guide on configuring 802.1X authentication using the AnyConnect 3.0 NAM module. I have the information required to configure the NAM module but need pointing to a guide on how to set this up on Cisco Secure ACS server side and IOS switches, for example a Catalyst 3750 switch.
View 1 Replies View RelatedI have inherited a site where the builders have installed a 2504 controller with 8 access points. Unfortunately they have not created an ap-manager interface when they did the set up. Is there any way I can do this via GUI or command line without going back to defaults?
View 7 Replies View RelatedI have a computer running Windows Vista that has been unable to access the internet, either with wireless or cable. It just says that no connections are available.Troubleshoot doesn't detect any problems.I also realized that I cannot access device manager, nor can I add/uninstall anything. When trying to get into device manager, I get " the specified service does not exist as an installed device".
View 3 Replies View RelatedI try to configure in both Clean Access Manager and Switch 3560E-24Ps on SNMP Version 2 protocol but I can't make it working together (For CAM and Switch 3560G-48Ps I can do that). [code]
View 3 Replies View RelatedSo instead of using 192.168.* how can I have computers on my router use my school's 152.65.*? It'd be nice for sharing things around the place. I'm just not sure a WRT54gs2 can do this as I'm not sure its software allows for such routing capabilities.
I sort of know how one would theoretically do this (I'm currently taking a networking class at school) but can I do this with a WRT-54gs2?
What ways can i connect the two building networks together(i.e best tools to use) supposing each building has a router. How will i make computer no. 10 accessible by all computers in the network.
View 1 Replies View RelatedI manage the network of a small (120 users) network spread out over 5 sites within a 10 mile radius (for normal ops- extended ops can expand to include other cities).I think I'd call that a Campus LAN, perhaps it's just a really small MAN (for normal ops)...I am starting my CCENT/CCNA track so this may be blazingly obvious to some of you- but I'm sure to learn something either way...Every now and again we have to go find "hostname "X"" for an update that won't roll out by way of our (Server Sr SysAdmin's) tools, so we actually have to put hands on it. Unfortunately the prior admins didn't document the inventory to such a level that we know "laptop_015" is in the building down by the college.
I DO have documentation on my equipment (I'm the Network Sr SysAdmin) that I have rolled together over the last 9 months being here...I have a Cisco 5520 ASA, and use ASDM to manage it. What would be extremely handy would be the ability to put a query in the system to report back what switch a given hostname is plugged intoBetter yet, if it could tell me switch and switchport.I imagine this would be simple if I had the MAC address- there's got to be a way to grep the switches for a given MAC- but not sure if it'll work in a similar fashion for ARP lookups.
I have a task to compare different approaches to implement InterVLAN routing in campus network. Google suggests only Cisco technologies for such query. But what I need is also other companies solutions (like Dell, HP etc), cost of the implementations, pros and cons.
View 1 Replies View RelatedI'm going to start the evaluation of implementing the virtualization of our campus LAN using MPLS.We'll get many inter-VLAN routing domains per VRF on the same LAN infrastructure.The LAN infrastructure is based on C6500 implementing VSS.Do you have experience with this kind of setup?Any known/faced issue that might prevent the setup of MPLS on VSS enabled C6500?
View 4 Replies View RelatedI manage a small/medium sized campus network consisting of 4 Cisco 6500 series chassis (each with SUP720's) and a couple hundred Cisco 3550/3560/2960 edge switches. We recently completed a new leg of fiber that will make a completed loop between all of the 6500's .... before I make the pyhsical connection I need to figure out my OSPF entries on each 6500 switch.
View 4 Replies View RelatedIn regards to a WAN connection, how would you recommend we connect a leased campus to our existing network. It is a temporary location that must be connected for a year.
We have an available 3845 with a VWIC2-2MFT-T1/E1 card. We are supposed to be getting 2-T1 lines from Verizon. I have a spare 3750 L3 switch for the core and 6 access switches.
I have 5 Static Ip pool all IPs are working fine. I have deploy a IIS Server on Windows2008 and configure the Static IP on that server. earlier it was working fine . but since last month the IP is not pinging from Out Side but internal IP Pool its working. I have checked the SERver firewall and another Setting is Ok. if i changed the Ip from the server the new IP is also not pinging.
View 1 Replies View RelatedHow to setup a WIFI Network in a large campus building.
View 5 Replies View RelatedI`m working on Dynamic Vlan Assigmenton the basis of end user authenticatedwhoc are part of specific AD Group in c ampus enviorment.Objective: Need to assign the vlan on switch port on the basis of authenticated users OU Group in Active Directory. Eg: There are 2 OU groups in AD, Sales and Administration. Authenticated user in Sales group should get Vlan 10 and user in Admininstration Group shoudl get Vlan 20.
Components:
Cisco 3750x/Cisco 4500
ACS Version 5.2
Microsoft AD
we are running callManager 7.1 (user accounts are tied to AD)... one night our call manager got rebooted by IT. upon reboot, CM failed over to the Subscriber node. Some how IT got Callmanger back over to the Publisher node.....No now of us can log into CallManager using our AD accounts...
View 2 Replies View RelatedWe got recently a Cisco Secure ACS 1120 and i upgraded the Appliance to 5.1 from 5.0 with all your support
Now I need to integrate Cisco ACS 5.1 with RSA Authentication Manager 6.1 . I Successfully Downloaded config file from RSA ACE Server and exported into ACS 1120.
I also Added ACS as a NetOS Agent in the RSA Server , during the process i found few warnings . The ACE Server is not able to Resolve the IP Address to NAme ( DOes it Necessary ?? ).
I havent created any secret Key file for communication between ACS and RSA and encryption i used is DES.
Now when I log into ACS and search for Devices in the Identity Store Sequences i am not able to Look for RSA Token Sever .
I want to know if the Cisco 2900 series can do UC without having to buy any other hardware.I read through the 2900 series datasheet, and i can understand it does.But will want to clarify if i do not need any other hardware except the Unified Communications License for Cisco 2901-295.Does this mean all i need to activate UC is buying this license?My organisation wants to do UC, especially Voice and Wireless.It requires APs, IP Phones(both wired and wireless).To achieve this on a 2900 series, is all i need just the UC license to work, and then my IP Phones both wired and wireless once plugged to the switch connected to the 2900 series starts working?Or do i still need to buy another hardware for the Unified communication Manager Express ?
View 1 Replies View RelatedI would like to use the Cisco ATA 186 as a SIP device with Cisco Call Manager 7. However, I have found that the SIP firmware for the Cisco ATA 186 is unsupported by Call Manager 7.Therefore, In order to use the ATA as a SIP device with the Call Manager, I believe I will need setup the ATA as a 3rd Party SIP device by doing the following:
1. Disable the TFTP option within the ATA, so that the SIP firmware is not overwritten by firmware from the TFTP server.
2. Install the 3.2.1 SIP firmware on the ATA, since the ATA is currently running the 3.2.4 SCCP firmware.
3. Register the ATA, as a third-party SIP device, with the Call Manager .Should I register the ATA as a 3rd party device?
I have a CUOM 2.3 and CUCM 7.0 installed, we are planned to have a major upgrade to CUCM to 8.5 soon, do i need to upgrade my CUOM ,since CUOM is a Network management system? If CUOM to be upgraded to 8.X do we need to purchase the upgrade license? Is OM 2.3 to 8.X is a direct upgrade?
View 3 Replies View RelatedMy Customer today have CUOM 2.3 and CUCM 7.1.3. He is planning to do upgrade CUOM 8.6 and CUCM 8.6. My question is: Is it possible to do upgrade CUOM directly to 8.6? If CUOM to be upgraded to 8.X do we need to purchase the upgrade license?
View 4 Replies View RelatedThis is Cisco Prime LMS 4.2.2 on Windows 2008 R2
As far as I understand it Fault Manager need to be able to do reverse lookup for ip adresses to show the correct name in the "device name" column. I have double and tripple checked and all devices that only is shown as an ip address do have a reverse in the dns used by the LMS server. The device is correctly registered and inventory have been run. If I hold the mouse pointer over the crosshair on the row of the offending device all info is shown including correct device name and fqdn.
The server is upgraded from 4.2.1 to 4.2.2 and we have the same problem before the upgrade.
When trying to start CiscoWorks Daemon Manager i get the following message:"The CiscoWorks Daemon Manager service on local computer started and the stoped. Some services stop automatically if they are not in use by other services or programs."I have tring starting the service from DOS also and get,E:Program FilesCSCOpxsetupsupport>net start crmdmgtdThe CiscoWorks Daemon Manager service is starting.The CiscoWorks Daemon Manager service could not be started. The service did not report an error. More help is available by typing NET HELPMSG 3534.
View 11 Replies View RelatedDoes two separate SCE 2000 devices can share a collection manager, or do they each need a separate CM? If they can share, is there any special setup on the CM itself?
View 0 Replies View Related