Both the SLM2008 switch, and the AP1262n-a-k9 are currently at factory defaults. I can web into the switch from my laptop, but when I connect one of the 4 AP's I am trying to set up, the switch doesn't see it.
View 4 RepliesI had a SG200-8/SLM2008TNA switch that I was using on my lab network (192.168.9.x)One of my clients had an emergency so I moved the switch to their network (10.1.2.x)I can't see the switch at all! Cisco FindIt toolbar won't discover it (other switches on the client network are discovering OK)I changed my computer's IP to the range where the switch used to live...still can't find it I also don't see any new devices in DHCP with cisco-looking MAC addresses.Of course, the SG200-8 doesn't have its MAC address printed anywhere on it, and doesn't have a factory reset button.It's passing traffic OK but I was hoping to get it configured via web console and set for SNMP monitoring. how to discover/reset IP/factory reset this thing?
View 2 Replies View RelatedI would like to edit .cfg configuration file of Cisco SLM2008. However, I can't read the file because I don't have a good editor(.cfg is a binary file).
View 1 Replies View RelatedI have just attempted to load the latest firmware on an SLM2008, everything appeared to work as expected BUT, the switch is no longer pingable on its static IP doesn't appear to have attempted get an address via DHCP. I have attempted power cycling the switch but it has made no difference. The switch is still switching but I have no management any more. What to do next ?
View 1 Replies View RelatedI'm new on this site and having SLM2008 switches. I've been trying to solve the problem for quite a while, but so far I was unable to solve it. So here it is:
I'm trying to send IP TV from ADSL box (aka Free box) located in a small annexe of the house where the telephone line enters. Whole house is wired with 1Gb CAT6 cable. I'm using this wiring to get internet connectivity in different parts of the house and this works great. Now the idea was to create a separate VLAN on my 3 SLM2008 switches to get IP TV stream from ADSL box to the media box (also provided by ISP, aka Freebox HD). Different V LAN configs did not work for me: Free box HD would stuck on boot claiming it doesn't "see" the network. So then I've decided to go from simple things to more complex and removed the V LAN (came back to default config) and connected ADSL box with Free box HD with just one SLM2008 in between. Surprisingly it did not work! Same error on Free box HD! So I plugged the hub and started my Wire Shark to see what is going on.
First tried without the switch (just with a hub in the middle) and I saw successful connection:
1) Freebox HD send DHCP Discover
2) ADSL box responds with DHCP Offer
3) HD sends DHCP Request
4) ADSL issues a DHCP lease
Free box HD is ready to show any channel from ISP.
Secondly I plugged SLM2008 back and looked at traffic right after ADSL box: No DHCP packets seen at all! Then I moved hub next to Free Box HD and I saw it keep sending DHCP Discover every 30 seconds or so.... And it was not getting reply back.
So my conclusion is that SLM2008 for yet unknown reason would not let DHCP discover pass.... I've tried un managed Net Gear switch and *boom* Free box HD booted without a problem. I looked through SLM2008 settings and I have not found something relevant.
How to make my switch pass DHCP discover? If yes my next question would be how to configure V LAN on 3 switches to make it deliver IP TV to my TV set.
Which transmit hash policies are supported by the SLM2008? I can't find this information in any of the documentation for this switch, all that is stated is that it supports Link Aggregation using IEEE 802.3ad LACP. I'm connecting to a Netgear ReadyNAS Pro that supports Layer 2 and Layer 3+4 transmit hash policies and I'm not sure which to choose (or whether it matters).
View 2 Replies View RelatedI have the E3000 wired/wireless router and want to be able to manage my two SLM2008 switches with 192.168.1.253 and .254. Following the guides with adding vlan 2 and tagging the ports in which the two switches are wired together disables my ability to manage them seperately. I have added the gateway on 192.168.1.1 to both switches and told them that management vlan is 2 but no luck accessing them still.
View 1 Replies View RelatedSome days ago, I download standard IOS image for 1262 and installed, now this 1262 AP can start up without WLC. but I don't know how to recovery this AP image, and let's startup / download the image from WLC and has been managed...Is that ONLY remove the existence image ? and it's will be auto find WLC ?
View 5 Replies View RelatedEnd user has a AP1262 which at the beguinning was working fine, suddendly clients reports problems with disconnections. [code]
the version of IOS is Version 12.4(25d)JA., WPA- PSK is set,I have check this errors in cisco tools, it says about possible reasons; one of them
A failure of the Michael MIC in a packet usually indicates an active attack on your network or RF problems.For the moment I set countermeasure tkip hold-time 0 , based on some recomendations in this forum.
I have a running Mesh Network with AP 1552E and Controller 5508. The end customer has a new requirement to have a indoor coverage near to AP1552E (mesh AP). But in this building he has not any wired Network (it is far from any switched site). The question is: We can use an AP1262 indoor with Line Of Sigth to AP1552E in the running Mesh Network? I know AP1262 can be used in a Mesh Netwok (Root or Mesh) configuring it as BRIDGE [URL]
View 1 Replies View Relatedwindows seven changes my ip address after sitting idol for awhile. I have to reboot and reset my modum the computer is brand new
View 1 Replies View RelatedWhen setting up Belkin fF5D8235-4 v2 router it will not recognize the Speedstream 4100 modem. Is there a fix for this?
View 1 Replies View RelatedI have a Linksys WRT110 wireless router that has never given me any problem. All of the sudden, after a storm blew through yesterday, none of the laptops in my house (PC running Vista and Mac) will recognize my wireless network. I have a desktop computer and BluRay player hardwired to the router and the internet works fine on them through the router.The problem is not that I can't connect or lose connection, the wireless network isn't showing up as existing anymore, like it has disappeared.
View 3 Replies View RelatedIs it possible to assign 2 ports to a vlan on this switch and have the 2 machines connected to those ports be able to see each other without having to go off of the switch? If so, how would it need to be setup on the switch?
View 4 Replies View RelatedOne moment the laptop was using the wireless connection from the router in our house and the next it lost internet access and then wasn't able to recognize the SSID or connection at all on the available wireless connections. We have reset the router and restarted the laptop countless times yet the only internet access we have is on the computer the router is hooked up to.The wireless connection works neither on the laptop nor the Wii, both previously works merely hours ago and with no problems until now.We assume there is an issue with the router itself, whether it be a loose ethernet cord (which only faintly can be moved in its place).It's almost as if the router is stopping them (Wii, and laptop) from having access. When we explore the wireless internet properties on the laptop, it shows the wireless connection, yet only there and doesn't give access to it. Could it be the router, or could the company have restricted WiFi only to the computer it is hooked up to?
View 1 Replies View RelatedI have a 300 series switch with VLAN1 untagged, VLAN 15,5,100 tagged. I want say ports 1-12 to use one uplink/trunk and 13-24 to use another uplink. All ports should have the same default VLAN1 and be tagged for 5,15,100. I'm trying to ease the load on two wireless uplinks(one is a Cisco 1242AG and the other is a UBNT PowerBridge.) I don't want to add another switch. Model: SF 300-24P
View 5 Replies View RelatedI have a question, does the SG300-28 support VTP and STP?. I want to add it to my network's VTP domain so I don't have to manage vlans manually on the SG300-28 and also be able to configure STP to keep my network loop free.
View 2 Replies View Relatedi found that cisco small business SF302 PoE managed switch connect with the end device (RFID component) would causing packet drop issue.how should i isolate the issue and proper troubleshooting? would it cause by the PoE issue, or the 10/100 base etc.
View 5 Replies View RelatedFor test I used 2 Switch that name "ESW X" and "ESW Y" I have 2 network that I named "Network A" and "Network B" I build 2 VLAN for each network that named Vlan 2 for Network A and Vlan 3 for Network B, I don't use Vlan 1 because it's the default Vlan
Configuration ESW X:
port e1 : ACCESS PORT on UNTTAGGED Vlan 2
port e2 : ACCESS PORT on UNTTAGGED Vlan 2
port e3 : ACCESS PORT on UNTTAGGED Vlan 3
port e4 : ACCESS PORT on UNTTAGGED Vlan 3
port g3 : TRUNK PORT with UNTTAGGED Vlan 1(default) and TAGGED Vlan 2 and Vlan 3
[code]....
Each Vlan can't communicate between the two switch, I think they're a problem in my vlan/port configuration?
I would like to configure a switch to act like a Hub. I know about the mirroring port configuration, but unfortunately is not enough for me. Is it possible to do that with the switch that I have (i.e. SG 200-08) ? If not do you know a switch on which I can configure it like a hub (that mean no flow control between physical ports).
View 1 Replies View RelatedHave deployed a few of these - and am truly frustrated that I cannot see then in the topolgy, let alone actually manage them. Why such a ubiquitous switch is not supported.
Even the SmartPort utility is useless - CCA (3.3.1 and earlier) gives an error saying a port is incorrectly configured (I pluggged it into an exp port on the UC560 as I gave up trying to get a working uplink to an ESW-540-24P).
The Smartport port function wants the exp port (on the UC560) to be configured as a "Phone/Desktop" - if I try to change it to a "switch", it refuses to accept it saying the "Macro is unsuitable - or similar"
I am trying to setup an ACL on SG 300 switch. I want to create an ACL that enables hosts on our guest network to obtain IP addresses from a server on our "internal" network but they should not be able to reach any other resorses on that network. I set it up as follow, but it does not work the way i want. I have also bind interfaces to the ACL.
View 4 Replies View RelatedI am interesting is ESW-520-24-K9 switch supports GLC-LH-SM SFP? In official data sheet there is no information about that. it is supported and I am interesting if it is true ?
View 5 Replies View Relatedossible to connect a pair of switch serving the same segment (active/passive) into 1 switch?
View 6 Replies View RelatedI am having an issue with LAG configuration on a Cisco SG300 52 switch. I have connected four Ge ports on the switch to the four NICs of a Dell R710 Server on which I installed Windows Server 2008 R2. Without LAG configured, these ports would forward traffic to and from the Dell server fine.However, if I configure LAG on the ports with LACP enabled, then they would not forward any network traffic. Debugging shows that the ports are up but their forwarding status show N/A. Am I missing any configuration? Can I configure LAG on edgeports?
View 2 Replies View RelatedI have configured stack with 2 sge2010p switches. I want to connect this stack to the HP procurve switch using port agregation (LAG) technique. I want to use one ge port on each sge switch.How to configure it? Will it work witch port agregation on procurve?
View 2 Replies View RelatedI have a SF 200-24P Cisco switch that seems to be rebooting constantly, When i connect it to mains power it seems to go through a startup cycle, in this order - i have tried this with no network devices attached and the same thing happens
1. Fan starts - continously runs
2. Very quick flash of all RJ45 ports.
3. After about 30 seconds, any network devices connected have an acticity light
4. After about another 45 seconds, all ports light up including the activity and POE orange LEDs for about 5- 10 seconds then go off.
5. About 10 seconds later the ports all light up again and stay on for about 5 seconds.
6. All ports go off and the cycle keeps repeating continously.
I have tried pinging the switch without success.I have also tried disconnecting all devices from each port with no success.At no time does the system LED on the left light up.I have tried resetting to factory default with reset pot on the left side.This is a brand new shipped switch from our cisco supplier, could it be DOA?
Any way to access the usual command line interface instead of using the GUI or Telnet/SSH interfaces on the Cisco Small Business SFE2010P switch? Note that the console port is not working at the moment...
View 4 Replies View RelatedI turned unplugged it and plugged it back in. Now its blinking green power LED. Is it dead?
View 2 Replies View RelatedWe just purchased 8 managed switches POE to swap out our existing in preparation for our new phone system. We installed them all after configuring with static IP. Deployed... and all but two work fine. Any tips for troubleshooting why two of them do not work? There are a couple other switches in the building. Could it be that a switch "upstream" from the two non-functioning switches is causing an issue? If so, how do I find out? When we put back the two "dumb" switches all was fine.
View 1 Replies View RelatedSRW 2048-EU(webview) switch will support how many SFP minigibic whether 2 or 4 ?
View 1 Replies View RelatedI want to create a network with the following switch SF 300 - 08.I am not use to GUI.I am having problems setting the settings.Currently, i have assigned each port with a vlan 1 to 8 for ports 1 to 8.How do i do an inter vlan with the GUI? Also, i want to restrict port 7 and 8 to certain ports only. Example:Port 7 and 8 can read port 5 and 6 but not others?
View 9 Replies View RelatedI have fiber optics no router One static IP address, when connect SF 200 the system LED flashes and there is conductivity.I checked ther is no setting for static ip,Gateway,DNS, so is this unit only for Dynamic address
View 3 Replies View Related