I want to create a network with the following switch SF 300 - 08.I am not use to GUI.I am having problems setting the settings.Currently, i have assigned each port with a vlan 1 to 8 for ports 1 to 8.How do i do an inter vlan with the GUI? Also, i want to restrict port 7 and 8 to certain ports only. Example:Port 7 and 8 can read port 5 and 6 but not others?
View 9 RepliesI have a brand new SG500-28P sitting on my desk.
The swtich is configured and going to operate in L3 mode. All ports are still assigned to the default VLAN ID 1. I have created several new VLAN's. Once I configure and aplly an IP Interface to a certain VLAN the swtich becomes inaccessable right away. I am pretty sure I am not pulling my own VLAN under my connection. Every port is inaccessable. I have to pull the power plug and restart the swtich with its saved configuration. Even when I add another IP interface to the default VLAN 1, same issue. I have tried lot's of things, but can't get it to work properly. I have just upgraded to the latest firmware.
I have configured dozens of SG300 swtiches which is very easy. This one does not work with me.
I used two sf-300 switch and create 4 vlans and intervlan routing is working fine.
Port 1 - 10 -------------> Vlan 1
Port 2 -20----------------> Vlan 2
Port 3 - 30------------------> Vlan 3
Port 4 - 40--------------------> Vlan 4
giga1 -----------------> connected to router (This router used for intervlan routing).
SF-300 Port 1 is connected to Internet Modem. This modem worked as dhcp server also for vlan 1, my problem is that when vlan 1 is not communicate to vlan2,3,4 and 2,3,4 are not communicating.
How i can communicate vlan 1 to 2,3,4 vlan.
how i can connect the modem in switch? Access port or Trunk port ( Presently available in vlan 1 Access port)Any route i need to make? sf-300 or modem or router?
Got two pc's, two routers and one switch, and two serial cables and I want to create a network.
View 4 Replies View RelatedWhen it comes to fiber optics my knowledge is very limited. All I know is that they can carry data at high bandwidth for a long range at blazing speeds etc.My boss has asked me to link several buildings to the network and I am led to believe that joining them through fiber optics to be best since we are expecting a lot of data traffic between.I have done the normal RJ-45 networking with Gigabit networking in my organisation but need your assistance on how to join each of the buildings through fibre optics.So far this is my plan.Draw up the fiber optic lines from the main building to each building.All the buildings have Gigabit Cat6e cabling and network in each.I am planning on using a single mode media converter to convert the end of the fibre optic to the normal RJ45 connector and plug it to each switch at each of the ends of the fiber optic cable .Am I going in the correct direction?I don't even know the gadgematics required except for the cables them selves, crimping tools, the media converter. There is about 300-400 metres in between of each building from the main building.Also, I believe that we need to create cross over cables as in the normal way we do in connecting 2 switches. Your input is very valuable to me.
View 9 Replies View RelatedIs there any management software as the Cisco Network Assistant for smb switch as SLM224G or SRW224G4-K9-NA, or only works with models 2960 and higher?
View 3 Replies View RelatedI need to create a LAG consisting of 4 ports on my SG 300-20.
When I go to create the ports via Port Management - Link Aggregation - LAG Management - LAG1 - Edit and move ports 5,6,13,14 over as LAG Members - Click apply I get Port gi5 belongs to a VLAN. If I try to add them individually I get the same error, i.e. port gi6 belongs to a VLAN, port gi13 belongs to a VLAN, etc..
how to get these ports out of a VLAN?
I have a spare usb HDD and wish to connect to an existing network switch (rj45 connections) if it works on a gigabyte network all the better
View 3 Replies View RelatedI work in a school department and wanted to hardwire two computers in my class using a workgroup switch. I only had one data port in my class. The tech guy told me the switch could cause the entire network to crash. Is that true? I thought a switch was just a passthrough device.
View 7 Replies View RelatedWe are about to move our IT rack to a data centre and will be adding a new Layer 3 (Catalyst 3560) switch beyond our ASA 5510 which will be providing our existing WAN plus another SVI which will be carrying our HSRP range.
I have never configured a switch to use two SVI's before and can't seem to find the relevant docs online.
Have one switch and network.PC number one have win98 and network adapter and connected to the switch.PC number two have winXP and network adapter and connected to the switch same as win98.Network works on win98 and winxp they see each other.internet working on winxp but dont work on win98
View 2 Replies View RelatedOn our HP switches we have an 'Outside' VLAN where any device connected to these VLAN ports can use the ISP's 'outside' IP addressing for direct Internet access to bypass our firewall. We use this for videoconferencing devices.What is the correct way to do this on a Cisco SF-300-48P??Presently I have ports 1-4 in vlan 50 Outside as 'untagged,' and the same ports as 'forbidden' in vlan 1 Default. Is this the correct configuration?? In HP switches these ports in vlan 1 Default would be configured 'No' and 'untagged' in vlan 50 Outside.Tried talking to Cisco but their phone support is not working.
View 6 Replies View Relatedi want to connect dvr to the internet i need the step to take and process of creating a public LAN Address
View 1 Replies View Relatedhow to create a password to access one pc to another pc .like i have 3 pc it is connecting throw switch .ip addresss is 192.168.1.1,192.168.1.2, 192.168.1.3 i want access from 192.168.1.1 to \192.168.1.2 like this here i want to create login password and how to remove password
View 1 Replies View Relatedcan we create VRF on Cisco 3550 EMI switch so that we can create mutiple virtual switch on physical switch.
View 4 Replies View RelatedI need to create a DMZ Vlan. Core switch is a 6509. FW is an ASA5520. Need to create a VLAN for DMZ purposes for outside facing servers. NAT is used on ASA.
View 7 Replies View RelatedIs it possible to create a stack with 5 WS2960-S series switches OR are you limited to only creating a stack of 4 switches.
View 1 Replies View RelatedTrouble connecting to the internet wireless with Motorola SB6120 and Linksys WRT120N. The modem works directly with LAN but as soon as I try to use the router, I can connect to the network but no internet is available.
View 4 Replies View Relatedhow do i create 2 networks using 1 cable modem and 1 router and i would like to add a firewall thinking of using xywall usg20 for the firewall..... the issue is i have a small business with 1 point of sale and1 back office computer.(network1) and i would also like to use an air port wifi to offer wifi to my cleints on a seperate network(network2) not allowing access to network1 and i want a firewall on network 1 to protect the back office and pos system
View 4 Replies View RelatedThis is regarding VLAN creation on C3750E switch.I want to create new Vlan 94 on this switch and also I want to allowed same interfaces like Vlan 95 & Vlan 96. [code]
View 7 Replies View RelatedI was wondering if I can stack WS-C3750E-48TD with WS-C3750G-12S together to created a single logical switch.
View 3 Replies View RelatedI have a router on which I would like to create a port channel that spans two different Nexus 2248TP switches, and then create a couple subinterfaces on the router's po interface. I've done this successfully on my primary router, but the config doesn't seem to work on the backup router. The primary is running IOS 15, while the backup is running 12.4.25d advanced IP. I do see the trunk come up from the switch side, and my router subinterfaces and po interface show up, however I'm not able to get anywhere from the router. It's not even able to reach other hosts on the same network. As soon as I remove the port channel config and use the physical interface and assign the same address used on the port channel interface, everything works as expected and I have connectivity.
interface Port-channel21
no ip address
hold-queue 150 in
!
interface Port-channel21.248
encapsulation dot1Q 248 native
ip address 100.100.100.1 255.255.255.0
[URL]
how do i connect client computers to a server using a 3g gsm sim dongle for each computer and the server aswell...sounds weird but the client computers are way too far away from the server computer.
View 11 Replies View RelatedI would like to know how to create my own network key for my everywhere wireless.
View 1 Replies View RelatedI've recently moved into a new flat above a pub. The pub has internet which we are free to use but there it is an open network with no password protection and I don't feel comfortable connecting all my devices to it.Is it possible to create another network within the existing one? Perhaps by using another router with a password protecting it?
View 10 Replies View RelatedI need to create a 5gb limit on a network. My friend is only allowed 15gb a month and their brother uses it all within a few days. Is there any way to make it where once he's used 5gb his computer is blocked from using any more?
View 1 Replies View Relatedhow to create WiFi network with uninteruptable roaming between Access Points while clients are moving.What hardware is the best here? Are there any manuals about that?
View 2 Replies View RelatedI have want to know that how to create network setup and how to do TCP / IP Property setting.I want to know about DNS server and Altar net DNS Server and their IP Address.
View 2 Replies View RelatedI need to create a network bubble..means..Let say I have 4 machines having IP address 10.1.1.1,10.1.1.2, 10.1.1.3 and 10.1.1.4 (these are not actual IP's, using them just for explaining). These machines are connected to public network. At a given point in time, I need to isolate these machines from the public network in a way where - All these 4 machines can talk to each other using the assigned IP's. - These 4 machines cannot talk to any other nodes in the public network. no other machines outside these 4, will be able to ping these machines.
View 4 Replies View RelatedI need to buy wireless dongle & I'm most likely going with 3.
Can I create a wireless network from a dongle to connect an Archos A28 (Android portable tablet). Like Laptop (Vista Business) connected to internet through dongle in USB slot & Archos can also access internet through said dongle?
Or will I need to buy something like the Mifi thing that is designed as a portable wireless hotspot & connect my laptop & Archos to this?
I would like to create a network between my laptop and desktop PC so I can use the printer.
View 1 Replies View RelatedMy desktop, which runs on Vista, is connected to the internet via a cable modem. I am trying to get my laptop, which runs on Windows 7, to connect to the same network without a router via the use of an Ad-Hoc network.
I have created the Ad-Hoc network on my desktop and have successfully connected to it through my laptop. The problem is that although I am connected to the Ad-Hoc network on the laptop I cant connect to the internet. It simply says Access Type: No Internet Access. I have internet sharing on and don't know what to do to successfully connect to the internet via the laptop. When I diagnose the connection it says "The network adapter does not have a valid IP configuration" I have both pcs set to "Obtain IPv6/v4 addresses automatically" and dont know what else to do.
My question is can I split my cable to create my own network? For example my direct cable wire into the home then split it to tv then router to my laptop...
View 1 Replies View Related