I have fiber optics no router One static IP address, when connect SF 200 the system LED flashes and there is conductivity.I checked ther is no setting for static ip,Gateway,DNS, so is this unit only for Dynamic address
View 3 RepliesHow can I edit a static interface IP address? I don't seem to be able to edit the static IP address for my switch. How do I go about changing it? As you can see the IP Address field is not editable.
I have also upgrade to the latest firmware and I cannot figure out how to edit it via that as well.
how to switch between my 5 new static IP addresses that I purchased (on a monthly basis now) from my ISP. I need them for my business so that I can send out more than the 1,000 emails per day from the one IP address to all of my customers which total a little over 1,500 now. Unfortunately I'm quite computer iliterate when it comes to understanding even the basics of computer terminology, etc. My ISP explained to me that if I purchased the bundle of 5 static IPs, then I could in essence send out 5,000 emails per day, which is plenty.
View 3 Replies View RelatedIs there a way to set static ip addresses to each port on at sf 300-08?
View 1 Replies View RelatedI have a SML2008 smart switch. I want to set a static IP to each port
View 4 Replies View RelatedI have been looking at deploying a small core switch design for an important branch office that would consist of 2 cores with an etherchannel link and then 4 POE access switches linked to both cores utilising STP. I will also want static IP routing on the cores and will set up HSRP for gateway failover.
The initial switch I looked at for the core was WS-C3560E-24TD-S however after finding that there is no stock around of this at the moment I have seen the WS-C3560X-24T-S which looks like it will do everything I need including IP routing, HSRP and QoS for VOIP. The thing that concerns me is this is about £1000 cheaper so i'm slightly worried im missing someting.
My second problem with sg200-08 (firmware: SG200-08x_FW_1.0.6.2.stk) is when I try to add specific MAC address as secure:MAC Address Tables - Static Addresses - Add; insert vlan id, port, mac address and select "Secure":I get error message: "Error: Failed to Add 'Static Address' entry.
View 3 Replies View RelatedI have routing enabled, can build a static route, and go back and see it (sh ip route), but I don't know how to get the route right. I have one host (Host A) on Vlan 20 w/192.168.20.2/24 dg 192.168.20.11 (the vlan ip) and (Host B) on Vlan 30 w/192.168.30.2/24 dg 192.168.30.11 (the vlan ip). I can't ping them from any host man. I can ping the Vlans but not the host.
View 19 Replies View RelatedI got a static ip from my isp. I set up my static ip manually through my linksy router. I need the static ip to connect to a private network for my new job but cant connect to that network. I went to whatsmyip and found that my old dynamic ip is still showing up externally, it looks like my ip4 is using the dynamic as a preferred. My question is do i need to manually change the network connection on my LAN and wireless connection under ipv4 to change it from automatically obtain TO use the following address and put in my static? And do I have to change the DNS also? I am on a home network with one desktop on vista home premium and laptop windows 7.
View 5 Replies View RelatedI'm having troubles with this firmware in a SG300-28 switch. Actually the DHCP server, a new feature in this firmware release, doesn't work correctly. DHCP static reservations are not working: CLient ID and MAC address are not recognized correctly, and the DHCP server assigns the first free IP in the pool, rather than the reserved one.If Cisco engineers read this, plese correct the issue.
View 5 Replies View RelatedI have VOIP and was provided a modem, a Tilgen Router (Vood 452_A). I also currently have a Linksys WRT54G router. I also have a home surveillance system with a DVR that can be accessed via the net. I am trying to allow the ports to open so that traffic can navigate down to the DVR.My IPs:My VOIP has provided me with 6 static IP addresses. For sake of this issue they are:
67.xx.xxx.153, through .158My subnetmask is set to:
255.255.255.248My Settings:
The Modem is connected to world. To the modem I have the Tilgen Router connected. The Tilgen is set with an ip of .153 and the subnetmask listed above. DHCP is turned on and has IP range set for .154-.158. It is set in Bridge Mode with NAT and Firewall turned off. To that I have the WRTG54G router connected and assigned the router an Static IP of .154.. The cable is going into the Linksys WAN port.From a computer connected to a LAN port on the WRT54G, I see my public IP as .154, currently my internal IP is 192.168.1.15 so I believe I have to assign one of my Static IPs to this PC, however when I try to connect to the Linksys Router (.154) from the outside web, I am get a time out error. (also from a ping test.) My thoughts are to assign the Linksys to DHCP and use a range of .155-.158 to give each lan item a static IP. My question is will this work? Will each item in the network have its own IP and if I forward the port to the DVR that i needed, ie 80 for web client or 6100 for desktop client, will that forward through?Or do I set it to Router Mode and use the Tilgen to assign the ips.
On the Tilgen I also have an option for a DHCP relay or to turn off DHCP.
For clarification here is the setup chain
Broadband/DSL Line>>Tilgen Modem>>(LANPort1)Tilgen Router(LAN Port2)>>(WAN) Linksys(LANPort1)>>DVR/Computers
Found this walkthrough on setting the WRT54G into a Switch. If I did this, in theory the VOOD would assign those computers/dvr connected downstream via the WRT54G a static ip from my range set on the router. Then in theory I would not need to port forward port 80 since the DVR would be on its own public IP.?
i m using ISP provided modem+router and another D-Link Wireless router at the same time... My computer is connected to D-LInk's Router and D-Link's Router is connected to ISP's Modem...My modem's Ip address is : 192.168.1.1 Router's IP Address: 192.168.0.1ok but now problem is that now Dlink is connected to ISP's Modem and ISP's modem assigns different ip to Wl.Router. Both have DHCP enabled... But i want modem (which is also a router) to assign D-Link's router the STATIC IP... like 192.168.1.54Router Model is D-link DIR-615 Modem Model is ZTE EchoLife HG510a
View 1 Replies View RelatedThis is the situation in our Lab.We have one telephone line with broadband connection and a system which is connected to a modem to use this broadband facility. Recently we have taken two static IPs over this connection for a project work.Now what I want to know is, how to configure these static IPs, so that I can connect two systems (each one to one static IP) to use these static IPs and continue to access the internet in the 3rd (already present) system.
View 7 Replies View Relatedi was having probs with the daughters dell laptop wireless setup, was intermittent, downloaded latest drivers, went to set up the connection, im running 128 bit wep and the damn software will only take the first 9 digits? i have 8 other wireless devices running of this so i dont want to have to change settings on all of them?
View 5 Replies View RelatedI am trying to assign static ip address on vlan 1 interface , the model no of switch is SG300 & the firmware version is 1.1.2.0 .But whenever I type the IP address & press enter , a question is popped up asking for confirmation (switch0d851f(config-if)#ip address 1.1.1.1 255.0.0.0.
Please ensure that the port through which the device is managed has the proper settings and is a member of the new management interface.Would you like to apply this new configuration? (Y/N)[N] N )
We have recently purchased a Cisco SG300 and have been configuring it. [code] The VLANs have ACLs set up to prevent any communication between the Holly and Tempo VLANs (and their associated WAN VLANs).Each VLAN has a WAN available for it's use, which connects to external networks (including the Internet).In order to facilitate this, we have set up all the necessary ACLs and routes and confirmed that this all works.However, the problem comes when we assign the static routes that specify the default gateways.We add the two static routes below:
-0.0.0.0 next hop 10.10.200.254 metric 1
-0.0.0.0 next hop 192.168.200.254 metric 1
In this case, only one of the VLANs has WAN access. It is either Holly or Tempo (it can be either if the order the static route is added is changed).What we need is to force Holly to use Holly WAN and Tempo to use Tempo WAN, but we cannot see a way of doing this.Effectively, we want the following static routes: [code]
i wonder if i can make a backup static route for an existing link over wan using the below diagram
the Core Switch type is 3750 in both sides i`m using only static routing for all destination like
Core1:
ip route 192.168.8.0 255.255.255.0 172.10.10.30
Core2:
ip route 172.17.200.0 255.255.255.0 192.168.100.105
requirements is to track the reachibility for the core ip address from both sides & change the routing automatically to the backup tunnel line
We are currently preforming the upgrade from WCS v.7.0.230.0 no NCS 1.1. When we select the Lic file we get an error message "Unable to add any license without an NCS (L-NCS-1.0-K9) license." The file name is WCSUPG20121115142018448.lic.
View 2 Replies View RelatedI upgraded my SG500 switch firmware to 1.3.0.59, since there is a new functionality DHCP server v.4 well I must say I came accross the issue I cannot solve. DHCP server assign dynamic address - no hassles. troubles start with static IP hosts.I defined a couple of hosts with static address within the correct subnet. I tried with hardware address and client identifiers. no luck. my switch does not assign the IP address I assigned to the suitable mac address. to define it I use both CLI & Web.
ip dhcp pool host HP-Elliteaddress 10.10.11.7 255.255.255.0 client-identifier 01:d8:d3:85:cf:09:72client-name HP-Ellitedefault-router 10.10.11.1exit
ip dhcp pool host VAIO-Zaddress 10.10.14.108 255.255.255.0 hardware-address 54:53:ed:1c:a1:46
default-router 10.10.14.1exit
I need a switch to configure a static ARP entry for a MS NLB multicast.
Could answer me if I can do with the SRW2024-K9-BR?
I have a 2911 which works perfectly except I cannot access it via HTTPS. HTTP and SSH both work. I've regenerated the RSA-key several times but to no avail.The box has a host- and domain-name configured.
View 8 Replies View RelatedMy ASA 5510 has stopped accepting connections today. I cannot connect with ASDM either. ASDM hangs at "Contacting the device. Please wait" and does not return an error or time out. I can telnet into the device but my CLI knowledge is elementary at best. I'm trying to determine how to view or enable the correct logging and view via CLI. I have looked at the client log from one of the users that cannot get in and have attached it. It looks like Phase 1 is not completing but I'm not sure how to view what the ASA is logging. I have run debug cry isa and debug cry ipsec but it just returns to the prompt and I'm not sure what I should expect to see or what command to run to view the results.
View 3 Replies View RelatedIt's a linksys wireless router attached to their service provider modem and it can no longer recieve new connections. The pc's connected to it before still run through ti fine but any new laptops using the proper authentication and password are unable to make a connection.First thing I am going to try is a factory reset(they mentioned resetting the router but they may have just rebooted it)
View 6 Replies View RelatedI have a 2801 with a very simple config that's accepting telnet connections on port 6050 from everywhere:
View 1 Replies View RelatedI got a set of dhcp pool in one 3750 attached to diferent Vlans in the network, the wired network works fine, you can get from any switch port across the LAN a diferente VLANs IP. In my wlc2504 I got 5 WLANs with the DHCP server pointed to the VLAN in the 3750, but I just got one set of ip when i tried to connect to diferent WLAN, without connectivity, I can see all the Ap's, and ping the VLANs in the 3750,
View 4 Replies View RelatedI have two WAP4410N. One of he accesspoints is connected to our wired LAN, called by now AP1. The other accesspoint is connected to the first accesspoint by WDS (Client mode) called now by AP2. I have upgraded both accesspoints to firmware 2.0.4.2. Both accesspoints are set to the same SSID and channel (6) and are set to mixed mode (B/G/N). After I two weeks they started to fail. When I connect to AP1 I don't reveive an IP-address of our DHCP server from our LAN. I'm able to connect to AP1 from our LAN. When I SSH to the box and I do an dmesg command, I see the following messages:
ath_bstuck_tasklet: stuck beacon; resetting (bmiss count 36)
ath_bstuck_tasklet: stuck beacon; resetting (bmiss count 36)
ath_bstuck_tasklet: stuck beacon; resetting (bmiss count 36)
[Code].....
I'm still testing these devices and I hope I can use these devices in our production environment,which is not possible with these errors and outages.
I can't connect to AP2 right now. I think the whole wireless interface isn't working anymore, unless I power off/power on the box. But it's hard testing when it works ok for two weeks and then stops.
A client has an ASA 5505 with a base license. The version information and configuration is attached. In 8 hours, sometimes less and infrequently more, it becomes inaccessible. All connections are dropped and the only way to access the device is through a console connection. The WAN interface (VLAN 3) is connected to Verizon FIOS. The interface was set to 100 MBps and full duplex, but I just changed it to auto on both the speed and duplex to see what would happen. The LAN interface (VLAN 1) is also set to 100 MBps and full duplex It has not been changed.
The last time it happened logging was running, but nothing in the log indicated a problem. In fact, the last log entry was a couple of hours before the lockup (there's little or no traffic on the ASA while the problem is being diagnosed).
On 3750 switch with IOS c3750-ipbasek9-mz.122-55.SE4.bin "eigrp stub static redistributed" command will be executable ?
View 1 Replies View RelatedI need to get my netgear wireless router. I have tried every password I've ever used to no avail.
View 1 Replies View RelatedI just configured cisco 2600 as TS for remote dial in via USRobotics modem, I can dial into router, but its not accepting my key board input.
View 2 Replies View RelatedI just got one of these and it works pretty good except I can't get it to take more than a 32 character WPA2 PSK. Tried using Firefox and IE and it doesn't make a difference. This is for my house. I'm retiring an old Cisco 1200 series AP and as well as a Cisco 1130. Using the same PSK and it doesn't work. Even if I just put 32 characters and just try typing more characters, it doesn't accept any more.Running 1.0.0.3 code and don't see anything newer or any firmware for it for that matter.
View 4 Replies View RelatedI have installed a new ASUS PCE-N13 network adapter. My problem is this: The network adapter easily detects my wireless router (full strength) so I click connect and it asks me for my p/w. I type the p/w in and my computer instantly tells me it is wrong. I know full well the p/w is right because I live with 2 other people and they both have laptops which connect no problem.
View 6 Replies View RelatedFirmware Version: 2.00.01 build 15 Sep. 13, 2010
Firmware Verification: dcf86b5724049cb145f571a4bc21a17d.
I was able to connect using Gnome Epiphay Web Browser v 3.4.1 and found no problems on the WRT610N router.So-o-o Cisco, what do you recommend I do, seeing as how there is no later firmware to apply and nothing to configure that I can see.