I have a 2911 which works perfectly except I cannot access it via HTTPS. HTTP and SSH both work. I've regenerated the RSA-key several times but to no avail.The box has a host- and domain-name configured.
View 8 RepliesI have 5x WAP4410N Cisco access points, the wireless is not responding to join request from wireless clients and i can only access the admin page from the LAN side.
reboot does not work the only way to make it accept join requests is by changing parameters in the AP and save it, it will work for few hours then stops again.
I cant seem to be able to open a TAC case.
access https sites from my PC? I cannot access these sites from IE 9 nor Firefox 6. I even disable firewall to try getting access to the secured websites but to no avail. But this problem recently cropped up when i upgraded my PC from XP to Windows 7.
View 11 Replies View RelatedI installed the LMS as ova template on ESXi and be able to connect via SSH, but when I try to connect via http or https I got the following error.
ForbiddenYou don't have permission to access / on this server. Additionally, a 403 Forbidden error was encountered while trying to use an ErrorDocument to handle the request.
We have an ASA5505 UL bundel, updated with this license "L-ASA5505-SEC-PL=" to enable traffic from DMZ to Inside. No NAT or rules deployed for that yet.
On the Inside we have Exchange 2007 in a single server installation. The public url for smtp, ActiveSync, OWA and Outlook Anywhere is mail.company.se. There is a static NAT for outside traffic to access above mentioned services on inside. Now, on DMZ there is the WLAN for guests to access the Internet. How ever, our Smart Phones with WLAN turned on, cannot sync to the Exchange Server on the Inside! The DMZ gets IP-addressen from ASA on DMZ Interface with external DNS configured. How can I configure the ASA to achieve the function of ActiveSync from DMZ to Inside with the public URL from the phones?
I have a closed network that is not connnected to the internet, just other sites that we want to communicate with. We have a cisco router connected to the outside interface on an ASA5505 and a cisco router connected to the inside interface on the same ASA5505. I have an inside interface that connects our management LAN, five separate DMZ interfaces with a separate LAN (VLAN) on each DMZ interface and the outside interface that connects to the other sites. Data is not allowed to mingle between the five DMZ's.
Alll connections to the other separate nodes are handled with the router on the external interface. IPSEC GRE tunnels have been established between all sites and BGP routing has been verified. Pings are good between inside, dmz and external interfaces and between the DMZ's and the other sites, to include hosts on our local networks and hosts at the remote sites. Inter and intra traffic is enabled.
When a remote site attempts an https connection, the initial ACK handshake makes it through the ASA5505, but the return SYN/ACK is being knocked down and I don't understand why (it is not because of ACL's, they are any any at this point).
Why the return SYN/ACK to the remote site isn't getting through the ASA5505 outbound. Will probably have the same issue with FTP, but right now, just trying to solve one problem at a time.
ASA5505 is in routed mode, not looking to NAT since the IP addresses in the DMZ need to be reached by their real IP address.
So, i have set up a working Anyconnect solution, (see attached picture)
Firewall is a 5585-x ssp20 running 8.4.3
Core is cat 6500
Anyconnect client version: 3.1.00495
Configured vpn with a tunneled default route to 172.19.16.1 (Core - cat6500) No split tunnel is configured, everything has to be tunneled and monitored by WCCP in Firewall. Authorization is by Certificate Only.
I can reach inside servers (for example 172.18.254.37) i can reach DMZ server (for example 192.168.138.36) i can surf the internet on regular HTTP (port 80)
but, i cannot surf the internet or DMZ servers using HTTPS (port 443) also, ftp does not work. i have tried to reach external ftp servers who are open to all.
both https and ftp works from the INSIDE network.
I have tried to change the port for Anyconnect, to 444 (for dtls as well) and i can see that all the vpn traffic is going over 444, so 443 should be undisturbed.
but this is not working.. could it be a certificate problem, or am i missing something? NAT/PAT?
This is my NAT configuration:
nat (DMZ,INSIDE) source dynamic NET-VPN-DMZ-PORTWISE-NATED-BOTK HOST-172.18.254.69 destination static NET-VPN-REMOTE NET-VPN-REMOTE
nat (DMZ,INSIDE) source static NET-DMZ NET-DMZ destination static NET-ALL-INSIDE
[Code].....
I am working in an environment with 6 4402 all running 6.0.119.4 code and WCS 6.0.196.0. I keep getting an alert from WCS that the controllers cannot be reached "Controller '10.x.x.x' is unreachable. - Controller Name: 'Name'"
Now when I go to access the WLC through HTTPS I have no access at all but controller still responds to ICMP, HTTP, Telnet, SSH. I know I should have HTTP and Telnet disabled but since HTTPS keeps failing I would have no way to get into the controller. Is this a known issue in the 6.0.199.4 code? should I consider upgrading? The only fix I have found to work is to disable HTTPS reboot controller enable HTTPS and reboot again.
when my Linux VM is running!How's this for a mystery - last night I noticed that I could no longer access my gmail. Thought it might be down. This morning, I still couldn't access it. Thought I would try comcast, no joy either. Changed computers, no difference. Changed routers, no difference. Bought a new router and started plugging in network cables one at a time. My main machine first, everything works - http and https sites, a second computer, all good. The switch. Fine. Powerline. Still good. Then I plug in a Windows server running a Linux VM. Https sites on all the other machines stop working. Pause the Linux VM, restart router - https sites return to life. Went to Linux machine, re-enabled ipv6 (the only recent change on the Linux machine was to disable ipv6 since upon a reboot, Linux didn't have an ipv4 address). Restart Linux everything seems fine. A few hours go by, try to connect my wife's new laptop and at that moment wireless seems to stop. Restart router, wireless is back. But lo and behold, https is gone again. Unplug the machine that has the Linux VM, restart router, all is good.Ever see anything this weird?
View 3 Replies View RelatedIv tried about everything you can find when you google things about not being able to access a particular website but none work checking out all security settings, deleting all cache, disabling security, checking date and time, flushdns, use opendns, try other devices (not one device in my household can get to https pages on this one site), making sure root certificates are updated, bypassing router, unplugging internet and router to ''reset'', trouble shooting with isp, website, ssl issuer, other wildblue users, other website users, other tech forum, checking for virus and malware and I'm sure there's more that I can't recall at the moment. I am not the only user of this website with a problem and all us having a problem have satellite internet (different providers), however not everyone with my satellite internet (wildblue thru dishnetwork) has this problem as I have asked here...some do some don't Wildblue ''blocking'' a website's ssl? - WildBlueWorld.com Forums
I can go to the website toontown.com but I can not access any pages that are ''secure'' or https. Can't login and using satellite internet?
For some reason i can't get access anymore to the web interface of our ACS 5.3 appliance.Where i used to get a certificate warning first, and after that the ACS5 login screen, i now get totally no response anymore in my IE browser.
I can telnet to port 443 of the unit however. And i (fortunately) still have ssh access to the unit. So i did a reload (microsoft habits) but that did'nt solve anything.https access to other systems from the same browser is functioning fine
=================================
admin# sh ver
Cisco Application Deployment Engine OS Release: 1.2ADE-OS Build Version: 1.2.0.228ADE-OS System Architecture: i386
Copyright (c) 2005-2009 by Cisco Systems, Inc.All rights reserved.Hostname: <deleted>
Version information of installed applications---------------------------------------------
Cisco ACS VERSION INFORMATION-----------------------------Version : 5.3.0.40.8Internal Build ID : B.839Patches :5-3-0-40-55-3-0-40-8
=================================
We have recently upgraded the software on our two WLC 4404 from software release 4.0.xxx to 4.2.xxx to 6.1.199.4 and lastly to version 7.0.98.0.
We could access the WLC's GUI's using https when it was on version 4.0.xxx. When we did the upgrades from version 4.2.xxx to 6.1.199.4 we couldn't access the Admin page through https anymore but only through normal http. We enabled https through the GUI and through the CLI and we did do the re-generation certificate , without any success. We then upgraded to version 7.0.98.0 and we still have the same result , cannot access Admin GUI through https.
I have a ace board(Acsm) in my switch 6509.I need provide access for clients over https, my scenario looks like this post [URL] .But, i have only one interface, and need to configure nat for inbound clients, to access the server with ip address of the interface vlan of my ace(if i set ace gateway in a rserver, the ssl termination works). The Topology is: Client(https) -> Ace(Https) -> Ace(http) -> rserver (http). Need to configuring this nat? I need that external clients arrive at the server with the ip of the same network as him, he did not right back the packet to the default gateway, but the origin of the same network as him, so that the communication function successfully, end order.
View 1 Replies View RelatedI was unable to access my ASA 5520 using HTTP/HTTPS even on the management interface. I had upgrade the ASA IOS to asa832-k8.bin and ASDM to asdm-634-53.bin. But, the issue still the same.
My browser show the error message as attach image.
PGA-Firewall-02# sh run: Saved:ASA Version 8.3(2)!hostname PGA-Firewall-02enable password 8Ry2YjIyt7RRXU24 encryptedpasswd 2KFQnbNIdI.2KYOU encryptednames!interface GigabitEthernet0/0 nameif public security-level 0 ip
[Code]....
I use the Service port connected to the managementVLAN to manage the WLCs. When configuring HA with AP SSO, I lost HTTPS connectivity to the WLC, telnet still works fine.I researched the deployment guide and it states:
- When AP SSO is enabled, there is no SNMP/GUI access on the service port for both the WLCs in the HA setup.Why is remote access disabled using GUI when using HA, and how can I keep management of my WLC using HTTPS and an address in the ManagementVLAN.
Configuring an asa 5505 with 8.42 software.I need to access an https server on the inside via the outside interface. have moved the http server enable to port 10443.Tried to make a "network object nat rule"
object network Vejrstation nat (any,outside) static interface service tcp https https object network Vejrstationnat (any,outside) static interface service tcp https https.
I've recently installed a certificate on my ACS 1113 appliance and in the Admin setup enabled management access over HTTPS. Since then I've not been able to access the GUI console. I have done some troubleshooting and I'm fairly certain that I have a certificate issue as Firefox gives me the error: Certificate type not approved for application. (Error code: sec_error_inadequate_cert_type)when I try and connect. So I want to either reconfigure the management access to use just HTTP or remove the certificate. I have logged on to the serial console and there are no options her to do this. The RADIUS and TACACS functions are working correctly - I just can't logon via the GUI.
View 1 Replies View RelatedI have installed a new ASA5510 with CSC, and everything is working properly except the access to websites using https. All sites/access to them seem to be blocked by the ASA. I have read that this access is by default enabled and I have tried to add configuration to allow https access to the firewall but without success. [code]
View 6 Replies View Relatedi am unable to launch ASDM, and access https:// to run Asdm..everything worked find yesterday but now for some reason it wont work?When i am trying to log in with the asdm it just hangs on the connecting to device... please wait...When i am tryng access the https://... i get the ssl do you want to trust.. and i press proceed anyway and i get an error
Asa 5510
Device manager version 6.1
System image file is "disk0:/asa804-k8.bin
Also i am accessing the asa with ssh without any issues
I have been tasked to provide SSL(HTTPS) access to a server farm that will be accessible from the internet. Is this the correct guide to follow?
[URL]
I am assuming I will need to purchase a certificate to import into the load-balance r as well.
I configured 2960S switch as http server. I'm unable to access the switch GUI with non privilege 15 user, with privilege 15 user it's working.
View 7 Replies View Relatedi have 2 rv042 with a vpn tunnel between them.the problem is that i can't access https over the VPN !if i telnet 192.168.10.1 443 through the VPN, it's not working either. if i telnet 192.168.10.1 443 in my 192.168.10.0 network it's working so it's reall the VPN tunnel the problem.
View 1 Replies View RelatedI can not access my Linksys E3000 router via https://192.168.1.1.Before this mishap, I was able to gain access to my Linksys E3000 router via http://192.168.1.1 and/or the Cisco Connect software application on Windows 7. Yesterday, I went into my router's administration page and disabled http, and enabled https. I then closed out all browsers, restarted them and entered https://192.168.1.1
After that, I learned quickly I made a huge mistake to make these changes. I simply can not access my router admin wired or wirelessly. Accessing the internet works great, but router admin page is a no go.Firefox and IE states, "There is a problem with this website's security certificate." and was unable to proceed.Firefox even gave me the option to accept a security exemption to proceed, but that failed.
I have also tried using the Cisco Connect utility, and that also failed. I have taken these steps and not been able to access my router's admin page.I don't want to take the last final resort to reset my router and re-enter my settings again. I know I saved the router's backup file somewhere, but can't find it.Is there another way for me to gain access via https with http disabled? All I want to do now is go back in and change it back to enable http access.
To improve the security of my 4200 v1 router, I turned on in the router configuration "Access via HTTPS" and after the reboot I could not access my router via the browser even when I click on the browser message to continue. What do I need to configure either in the router or my browser to use HTTPS?
View 9 Replies View RelatedI was unable to access the web admin on my WRT160n v3 w/ latest firmware this morning. Reset config to defaults & was able to get in. Enabled HTTPS access & disabled HTTP access & was right back where I started; reset to defaults again & left both boxes checked. Can access via HTTP, but HTTPS requests get refused/reset.
The reason I needed access was that when I booted up my laptop this morning, my wireless card wasn't picking up an IP address via WIFI, only worked via ethernet, so I need to see what was going on there — several reboots of the router didn't fix, nor has it fixed the HTTPS access problem described above.
When accessing the E3200 router using then ERROR 501.Not Implemented.That method is not implemented. The error occured after enabling the "Local Management Access, Access via: HTTPS" option on the Administration > Management tab.I tried different browsers FireFox (version 10), Internet Explorer (version 8,9), the same error was displayed and no acces granted to the E3200 router. I reseted the router and tried the latest firmware 1.0.03 build 9 Feb 1, 2012, but after enablib the option the issue occured again and it is not possible to connect to the router.
View 9 Replies View Relatedi was having probs with the daughters dell laptop wireless setup, was intermittent, downloaded latest drivers, went to set up the connection, im running 128 bit wep and the damn software will only take the first 9 digits? i have 8 other wireless devices running of this so i dont want to have to change settings on all of them?
View 5 Replies View RelatedI have configured my CIsco 2911 router and there seems to be something wrong with my configuration regarding subinterface 0/0.102 The hosts on this subnetwork cant access the Internet and i cant spot the error.
Here is my running config on this matter.
class-map type inspect match-any LAN_TO_WAN
match access-group name LAN_TO_WAN
class-map type inspect match-any WAN_TO_LAN
match access-group name WAN_TO_LAN
class-map type inspect match-any GRE_TO_WAN
match access-group name GRE_TO_WAN
class-map type inspect match-any WAN_TO_GRE
[code]....
I am having cisco 2911-sec-k9 router.
And I got 2 internet connections from isp one is static ip leased line and the other one i dsl dynamic ip one.
What I want is i need to configure internet load balance between these 2 internet and also i need to use static ip for remote access vpna and for my exchange port forwarding.
My dsl line in 100 mps and my leased line 2mb dedicated.
I configured the router as with some example config i got on internet my internet is fine but load balancing not happening and i configured the REMOTE ACCESS VPN . I am able to connect the remote access vpn but no communication through remote access . i cannot reach any device through remote access.
Note: if load balancing is not possible how i can configure for internet traffic use dsl line and for remote access vpn and live exchange port forwarding through leased line.
I am attaching my configuration and also debug crypto isakmp status
We are currently preforming the upgrade from WCS v.7.0.230.0 no NCS 1.1. When we select the Lic file we get an error message "Unable to add any license without an NCS (L-NCS-1.0-K9) license." The file name is WCSUPG20121115142018448.lic.
View 2 Replies View RelatedNeed to Have both ISP to access internet/servers configure a Cisco 2911 router, It has two ISP one as primary 216.140.140.0, and secondary for backup as 216.150.150.0. I need to be able to access both the ISP's using the same interface Gi0/1. Since we have servers that have to have specific IP both when accessed and when accessing the internet so I used static Nat for the servers and Dynamic for all others. I did the following configuration but it does not work as i want it, if i unplug the Primary ISP from the unmanaged switch the secondary cant access the Internet or network.The secondary only works when the primary and secondary are both connected and have an equal cost Administrative distance, hence it is not available when the primary is down . Even though I can use a sub-interface instead of a secondary Ip address (which worked when I used it) I need to use the same interface using a unmanaged switch to which the outside interface of the router is connected and the two ISP's. Below is my configuration.
interface GigabitEthernet0/0
ip address 10.0.0.254 255.255.255.0
ip nat inside
[Code].....
I recently purchased a Cisco 2911 to replace my Cisco 1711 router. I copied the configuration from the Cisco 1711 router to the Cisco 2911 router. Everything seemed to work correctly except when I VPN tunnel into the Cisco 2911 router using Cisco's VPN client version 5.0. I can ping the router LAN interface from my PC that is VPNed into the router but I can no longer ping or access the devices on the LAN side of the router as I did on the Cisco 1711 router. I don’t see errors in the log or hits blocking anything in the acls. It’s using the same configuration that I had on the Cisco 1711 router, and this did work on the Cisco 1711. The Cisco 2911 router is running IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.0(1)M1, RELEASE SOFTWARE (fc1).
Here is the VPN clinet portion of the configuration: The LAN is addressed as 192.168.0.0/24. The router LAN interface is 192.168.0.1, which I can ping and access. I can't ping or access anything on the LAN (192.168.0.0/24) beside the router.
aaa authentication login vpnclientauth local
aaa authorization network vpngroupauth local
!
crypto isakmp client configuration group remote-clients
key 6 xxxx
pool clients
[Code]....
My ASA 5510 has stopped accepting connections today. I cannot connect with ASDM either. ASDM hangs at "Contacting the device. Please wait" and does not return an error or time out. I can telnet into the device but my CLI knowledge is elementary at best. I'm trying to determine how to view or enable the correct logging and view via CLI. I have looked at the client log from one of the users that cannot get in and have attached it. It looks like Phase 1 is not completing but I'm not sure how to view what the ASA is logging. I have run debug cry isa and debug cry ipsec but it just returns to the prompt and I'm not sure what I should expect to see or what command to run to view the results.
View 3 Replies View Related