Firmware Version: 2.00.01 build 15 Sep. 13, 2010
Firmware Verification: dcf86b5724049cb145f571a4bc21a17d.
I was able to connect using Gnome Epiphay Web Browser v 3.4.1 and found no problems on the WRT610N router.So-o-o Cisco, what do you recommend I do, seeing as how there is no later firmware to apply and nothing to configure that I can see.
It's a linksys wireless router attached to their service provider modem and it can no longer recieve new connections. The pc's connected to it before still run through ti fine but any new laptops using the proper authentication and password are unable to make a connection.First thing I am going to try is a factory reset(they mentioned resetting the router but they may have just rebooted it)
View 6 Replies View RelatedWe have an AP541N that has been deployed to replace a Cisco 1200 AP (B/G radio). The 1200 functioned perfectly in our environment. The new AP541N on the other hand seems to work fine right after a reboot but immediately starts to degrade service. Over a short period of time, the devices bandwidth degrades to the point were the wireless network is not usable. This happens with just one device connected. Eventually, the device stops accepting client connections. We are unable to get any relevant logging out of the device to diagnose the problem.
View 84 Replies View RelatedMy ASA 5510 has stopped accepting connections today. I cannot connect with ASDM either. ASDM hangs at "Contacting the device. Please wait" and does not return an error or time out. I can telnet into the device but my CLI knowledge is elementary at best. I'm trying to determine how to view or enable the correct logging and view via CLI. I have looked at the client log from one of the users that cannot get in and have attached it. It looks like Phase 1 is not completing but I'm not sure how to view what the ASA is logging. I have run debug cry isa and debug cry ipsec but it just returns to the prompt and I'm not sure what I should expect to see or what command to run to view the results.
View 3 Replies View RelatedI have a 2801 with a very simple config that's accepting telnet connections on port 6050 from everywhere:
View 1 Replies View Related A client has an ASA 5505 with a base license. The version information and configuration is attached. In 8 hours, sometimes less and infrequently more, it becomes inaccessible. All connections are dropped and the only way to access the device is through a console connection. The WAN interface (VLAN 3) is connected to Verizon FIOS. The interface was set to 100 MBps and full duplex, but I just changed it to auto on both the speed and duplex to see what would happen. The LAN interface (VLAN 1) is also set to 100 MBps and full duplex It has not been changed.
The last time it happened logging was running, but nothing in the log indicated a problem. In fact, the last log entry was a couple of hours before the lockup (there's little or no traffic on the ASA while the problem is being diagnosed).
Was online the other night when my network suddenly dropped out on me. I assumed it was the router, not my computer, so I restarted it and got nothing. Same with my modem. Then I completely reset the router and, obviously, lost the network I had set up. Didn't realize until today, when I downloaded the setup instructions and reinstalled the router with a new network that the problem might actually be with my computer. I can use the ethernet port to access the web both with the direct line from the modem and when using a line through my router, I just can't get my computer to work on the network I set up. I know the network is valid because it works with my smart phone and a couple of other devices. On my Mac, it shows up in the list of available networks and has full signal strength. Diagnostics in network preferences gives me the following message: "AirPort has a self-assigned IP address and may not be able to connect to the Internet."
View 2 Replies View RelatedI have Linksys WRT320N acting as AP with Mac filtering, yesterday I noticed that even not added Mac addresses can access the network!!The settings in Mac Filter page as following:EnablePrevent PCs listed below from accessing the wireless network.MAC 01: XX:XX:XX:XX:XX:XXMAC 02: XX:XX:XX:XX:XX:XX...when I changed it to "Permit PCs listed below to access the wireless network" no one is able to connect to the network!!!I think the AP is not accepting the MACs I added!I restart the router (Turning on and off) with no luck.Firmware Version: v1.0.03.
View 1 Replies View RelatedI just installed the firmware upgrade 3.0.03 for my WRP160N router. It is now not accepting my Admin password. Nothing else has changed expect network name now shows linksys and not my assigend network name (SSID)
View 1 Replies View RelatedI purchased a WRT610N router early this month, the wireless network was working completely fine when I first set it up. Today I tried to connect my laptop to my wireless network. The laptop isn't able to connect at all. I also got a Sony PSP which has WLAN on and that saying it cannot detect any access point which would be my router.
View 3 Replies View RelatedHow can I open the Nat for both systems on my single router.
View 2 Replies View RelatedI was told that this router would push the PoE to the WAP4410N. I hooked the AP up to port 1 and no lights or anything... The network is all cat6, patch cords are cat6 shielded if this matters at all... what am I missing.
View 3 Replies View RelatedIs it possible to have 2 hard drives connected to a WRT610N perhaps connected through a USB hub?
View 1 Replies View RelatedI have the Linksys WRT610N wireless router and would like to know if it is possible to block all domains ending in .XXX? The access restrictions let you type in a 'specific' URL, but using a generic domain name doesn't seem to work. I basically want to block all access to any URL that ends in .XXX.
View 5 Replies View RelatedI just bought a certified refurbished router. The model is WRT610N-RM. Where's what I've done:
1. Downloaded newest firmware from the site using old router, Then disconnected. Connected a lan cable to the new router. Powered up the router. Held down reset untill the light blinks. Went to the browser and typed 192.168.1.1. Entered password to go into router and upgraded firmware. 2. 5 Ghz Settings: Went to Wireless menu. Selected "manual", mode is "mixed" (If i chose N only for 5 Ghz, then It won't save my setting for internet security. Instead it will be "disable" no matter what". The rest was default. SSID is enabled. Then I set up the 2.5 Ghz. I have 3 other computers with N wireless card. Some others have G, however when I viewed available networks, I only see the 2.4 Ghz ssid. I tried to reboot and unplug power for 10 seconds, but no luck seeing the 5 Ghz.
ive tried all types of things i read online and it is stuck on moderate no matter what i do, im hooked into router directly, when i hook directly into modem it switches to open.
View 2 Replies View RelatedI am finding it impossible to set up port forwarding. No matter what I do I remain completely stealthed when I do a port probe via [URL]... The only way I seem to be able to open a port is if I enable remote management. When I do that, whatever port I specifiy as the remote management port is then fully open. Obviously, I can't leave a port exposed like this and, anyway, I need to open multiple ports for my purposes.
View 9 Replies View RelatedI have had no problems with my WRt610N fo 2 years. Yesterday a problem occured and today again. Namely, I opened my laptop (the lid) and suddenly it could not see my network (SSID) among the rest of the neighbouring ones. The WiFi indicator in the tray showed the yellow "!". Since I have another (secondary) router wired to the primary (WRT610N) I tried and succeeded to connect to it (same SSID, but type "g").
Today the same situation. This is the straneg thing - if I 1st connect to the "g" router after a while the WIn7 reports my SSID being of type "gn" meaning it now sees the primary WRT610N. If I switch off the secondary the netowork is maintained by the primary router showing "n". It seems like my laptop cannot see my router (but can see all other networks) until it 1sr connects to the secondary, and afterwards it sees the primary router and can stay with it.
Is LinkLogger the only option for reading logs on the WRT610Nv2? I read about Linksys's own software called LogViewer 1.14 but I can't find it.
View 3 Replies View RelatedI've been really stumped when I decided to start using xbox live. When ever I try to join my friends party I am slammed with a NAT error. For years now I have not been able to forward ports at all. Any port checkers come back with unable to contact your router.I am fairly certain its the router because, I directly plugged my 360 into my modem and everything worked like a charm.I've read on a similar post found here "Similar post" that updating the firmware might fix the issue?
View 9 Replies View RelatedI am trying to filter a URL, facebook and it is not working. I have tried rebooting the router and it is still allowing access. I have provided the settings and ranges for PCs.
View 3 Replies View RelatedMy WRT610n went out today for no apparent reason.All of my other peripherals are still running, but the router won't turn on. I've tried different transformers, outlets and powerstrips, with no luck -- no power. I've also tried a hard reset on it, with no luck.
View 3 Replies View RelatedHow is it possible to block facebook (or other sites) on WRT610N router, given that I have already set up Internet Access restrictions based on day/hour ?
View 9 Replies View RelatedAny success with a recent vintage Macbook Pro connecting to the 5.8Ghz channel on a WRT610N. I can connect with the 2.4 channel without a problem but I cannot maintain a connection on the high channel. Linksys support told me that the hardware was not compatible with the high channel.
View 3 Replies View RelatedTo connect my new "smart tv" with my wireless linsys WRT610N, smart tv ask to take off all protection such as firewall and antivirus. Doing so, I cannot connect my laptop with my router. Is there a solution to connect both at the same time?
View 1 Replies View RelatedI read an earlier posting about an issue between SPI on the latest WRT610N Version 1.0 firmware and a user's Apple TV. This pointed me to a "solution" to a perplexing problem I was having.
I have 4 machines, 3 connected via WiFi and 1 on one of the wired ethernet ports. I also have 2 Apple Airport Express units for audio streaming as well as 2 iPhones connected wirelessly.
Now for the symptoms, which are all new since updating to firmware ver.1.00.03.15:
1. The WiFi machines see the Airport Express units and can stream audio to them. However, the iPhone Remote app has trouble staying connected to iTunes running on any of these machines. A router reboot is a temporary fix, but connection is eventually lost again.
2. The wired machine cannot see the Airport Express units, nor can the Remote app pair with iTunes on that machine. It's as though no Bonjour-related functions work. Here, a router reboot also provides a temporary fix, but one that lasts only minutes.
Based on that prior post, I disabled SPI on the router and, lo and behold, the wired machine suddenly sees all Airport Express units and can pair with the iPhone Remote app!
I was going crazy, verifying that I was not having Windows Firewall issues, that there wasn't an incompatibility with Windows 7 (which I'm running on all), that this wasn't a Homegroup incompatibility of some sort, that Bonjour was up to date, etc. Only turning off SPI fixed the problem entirely.
So, Linksys ...Any firmware bug fix in the works for this? Can I safely go back to the prior firmware update without security or function concerns? If so, where can I get my hands on the older firmware file?
WRT610N Version 1.0 running 1.00.03.15
i used my 610N v2 for 2 years and recently i upgraded my network from 100mb to fiber 500mb , however, if i directly plug the lan cable to my computer , i can get full speed , but with 610N, the speed is limited to 130 for both upload and download .i had already upgrade my firmware and did factory reset, none of them work. Is it the limitation of the router ?
View 1 Replies View RelatedFor some reason, I have been trying to use QOS for several network related jobs (VPN, streaming). It would seem that when QOS is enabled and the appropriate ports are set which a high priority, the speed of my connection drops to a crawl. When I disable QOS, I'm flying again. I have confirmed ports, and protocol types (TCP or UDP) and nothing seems to work.
View 2 Replies View RelatedI just purchased a WTR610N and when I connect to the admin interface over SSL it gives me a cert that expired on 12/31/1970. I updated the firmware and that didn't change anything. How to get it to use a valid cert?
View 9 Replies View RelatedI want to connect one "wrt610n router" to modem directly through Ethernet cable and when i connect both of them every thing is working fine and iit gives proper internet connection through WLAN [code] But, when i tried to connect "second WRT610N router" through "first one WRT610N router" through LAN_cable(cat 5) then second router do'nt provide(give) internet connection second router ip-- 192.168.1.5
View 4 Replies View Relatedhow to set up my router settings/port forwarding to be able to use Wake on Lan with Depicus here is what I currently have:DHCP Reservation with the IP Address of my computer (192.168.1.xxx) and the MAC address xx:xx:xx:xx that I retrieved by doing ipconfig /all in the cmdMy Router address is 192.168.1.1 and the submnet mask is 255.255.255.0my DDNS service is disabledIn the Security tab, I unchecked Filter anonymous internet requestsIn Applications and Gaming, under single port forwarding, I have port 7 to 7, Both TCP and UDP, forwarded to the IP address of my computer 192.168.1.xxx and it is enabledMy network card is configured already, enabling WOL in the card's properties.Now when I use Depicus, I enter the MAC, my external IP address which I got from myipaddress.com, subnet mask I use 255.255.255.0, I select Internet, and then the remote port I use is 7,Doing that, nothing happens at all. however, I can easily wake up my computer if I am connected to the same local network at home.
View 3 Replies View RelatedI have a router WRT610N and I'm using the FTP option within. The problem is that within my network, I have the cable modem (from the internet provider ) and my router with the ftp server. When I'm trying to access the FTP from outside (internet) with FileZila I get this "Server sent passive reply with unroutable address. Using server address instead."
I 've checked the network config from FileZilla and if I'm using this [URL] in order to get the public IP, I get this : 127.0.0.1
I am using Window 7 and the WRT610N router. I got a bufflao 1 TB USB harddisk connected to the router.My PC can access to the Harddisk. However, but my pc showing the USB harddisk is full. I checked, there are less than 200GB file on the disk. why is that?
View 1 Replies View Related