For some reason, I have been trying to use QOS for several network related jobs (VPN, streaming). It would seem that when QOS is enabled and the appropriate ports are set which a high priority, the speed of my connection drops to a crawl. When I disable QOS, I'm flying again. I have confirmed ports, and protocol types (TCP or UDP) and nothing seems to work.
View 2 RepliesThe new firmware is killing the video streaming performance I have to revert to the old firmware Ver.1.1.28.146072 to be able to stream videos from the media server. I have been waiting a long time for a decent Firmware that will fix the multiple issues with this router but this is ridiculous every new firmware update brings more issues to the table I am feed up with the Cisco developers I have a WRT610N router that is performing better than this lemon router that Cisco just introduced in 2012.
View 2 Replies View Relatedi have WRT610N v1.0 with latest original firmware but ftp upload speed and torrent download speed is terribly slow.
View 3 Replies View Relateddecided first of all to connect an old router to the master (but not test) socket together with different cabling & splitter/microfilter - everything starting working almost perfectly (apart from downstream data rate was considerably lower than expected each time I connected - between about 1400 & 1600 Kbps - I have max. 8 Mbps).when I connected back my current router everything continued to be OK (apart from low downstream data rate) - until I would restart the current router and everything went back to very very slow.
View 5 Replies View RelatedThis only started about a week ago and everything was working fine before then. My router is causing my internet to be slow (I know this because it goes at normal speed when I am connected directly to my modem)
View 1 Replies View RelatedI am using virginmedia superhub which is supposed to give me a max of 30mbps. I use it wireless but am often getting fluctuations in speed - sometimes 500kbps upto 20mbps, nothing consistently close over 20mbps or close to 30mbps. I have bought a powerline kit - "develo olan 200 AV Wireless N" which has improved the speed but I still get fluctuations.
View 1 Replies View RelatedSince recently replacing my home router with a Linksys E2500, I have been getting Blue Screen of Death (BSOD) with my Company's VPN (AT&T). It only happens when I am running wireless with my E2500. If I am hooked up to my E2500 through a ethernet cable it doesn't happen. I have updated the BIOS on my Lenovo Thinkpad T410 and ensured all of my drivers are up to date. I am 99.9% sure the problem is caused by my Linksys E2500 because I have used my laptop on other wireless routes at work and school and never get this problem. I am also ensured that my E2500 has the current firmware installed and upgraded my Company's VPN to the most current level to no avail.
I am getting DRIVER_IRQL_NOT_LESS_OR_EQUAL Blue Screen of Death in agnfilt.sys.
I just bought a Samsung BD-D5300 Blu-ray player that allows a bunch of networking options including wireless and wired. I was using the wired option when I came across some conflicts with my network using a Linksys WRT350N v1. The Samsung conflicted with the Linksys's DHCP server. The blu-ray player turns off automatically when inactive. It was causing conflicts with my iPad 2, MacBook Pro and Motorola Atrix android phone whenever it got assigned an IP address. When I reset the router and my cable modem, it wasn't assigned an address for awhile, which fixed things, but as soon as it got an address again, it was caused conflicts by being seen as a LAN by my router. When it wasn't receiving an address, it got the automatic private IP address of 169.x.x.x. When I removed the connection with my router, the conflicts disappeared and my computers were able to access my wifi again.
View 1 Replies View RelatedI set up an E1200 about two weeks ago to replace our old DI-524 because our net speeds were getting throttled (the old router wouldn't support anything higher than 10mbps). The same day, we started getting modem resets (We have an SB6120). This never happened on the old router but it's constantly happening with this new one. It'll happen multiple times a day. I called Cox Tech Support and they pushed an upgrade onto the modem but it still reset. I don't think it's the router, since I don't understand why it would force the modem to reset, but this never happened before I installed it. The firmware is updated to the latest version on the Cisco site (1.0.02).
View 5 Replies View RelatedI've had an E4200v1 in use as my home's main router for about 3 mos. And while many others have reported disconnect problems (I think), I myself have never seen any. My router and its N & G wifi networks have been rock solid. Until yesterday that is.Now all of a sudden, most of my family is complaining about wifi disconnects, slow speeds, etc. (My primary PC is hard-wired so I don't see any problems whatsoever... the problem apears to be wifi-only)And the Apple devices (OSX & IOS) seem to have the most severe problems. But Windows devices have also seen problems, just not as critical.Also, it's worth noting that I've been running 1.0.04 the whole time, without any problems... it seemed relatively stable to me. That is until yesterday.
I've bounced the router, I've disabled/re-enabled Wireless G network. I've switched mode from "mixed" to "G-only" back to "mixed". I've changed the channel width back to the default of Auto (I had been using 20Mhz), which increased my throughput (as measured by Qcheck) so I'm leaving it "Auto".
I have an E1550 less than 1 year old. Lately, I have been losing internet on the AT&T modem. I called AT&T but as part of their diagnostics, I have to plug the modem directly into the PC. I have loaded the latest firmware to the E1550.Lose Internet but wireless connectivity to router exists.Internet light on modem is out (modem is connected to router)Unplug modem and leave off plug in, internet light is still out.Unplug router, plug router back in - no internet connection but do have wireless connectivity to router.Take cable from modem to router and plug directly into PC internet light comes on in modem and I have internet from PC.Take cable from PC and plug back into router .I have internet via wireless.What I can't figure out is what could be happening in router that would impact modem internet connection. I have replicated this at least 3 times. Yes, the modem is a bit old, but since plugging it directly into the PC works, I'm thinking it has to be the router and I cannot figure out why unless there's some sort of electrical thing going on in the router.
View 4 Replies View RelatedI work from home on a Lenovo Laptop. I connect to my work network, and ultimately to a midrange ISeries. For the past year I've had no major problems with my Netgear Linksys WRT54G. I switched to a Netgear N300 last weekend because my husband's desktop was having a lot of issues. His connection is much better now.I'm able to connect to the internet with no problem, and I can access my company network & email pretty well. But, when I log on the ISeries it slows to way less than a crawl. According to my netwok icon, the connection is anywhere from 104 to 130 MBPS at any given time. But it freezes up so badly that it takes about 20 - 30 seconds just to type each letter, or to go from one window to another, or just to move the cursor down one line. It's infuriating. Every once in awhile if I disconnect and reconnect it works almost normally for awhile, but eventually slows down almost to a stop again. I actually worked for about 90 minutes the other day with no problem before it started acting up again. When I put the old G router back it works fine again. My laptop has an Intel(R) Centrino(R) Advanced-N 620 wireless adaptor. As long as I don't connect to the iseries, I have good speed and no issues with the internet or work intranet.
View 1 Replies View RelatedMy new HP Touchpad 32 GB is causing my E4200 to reset. I can duplicate the issue by simply access the HP App Catalogue. I upgraded the firmware from 1.01 to 1.03 build 13 and the issue still exists.
View 1 Replies View RelatedI have been using my DIR-655 for about 2 weeks now with Road Runner wideband services. Starting yesterday my internet became very slow and I discovered the cause was the router. I tried resetting it to factory settings and things will be fine and run smoothly for about 5-15 minutes but after that it goes back to being extremely slow. My speed tests would go from 10ms (normal) to 250-450ms. Before this issue occurred the Dlink was perfect, had full speeds. I am running a wire Ethernet connection.
I am currently using revB and tried upgrading firmware to 2.01NA which had no effect, but make my internet seemingly go back to normal for the first few minutes then nosedive again.I have also changed my speed/duplex settings in Network Config to 1gbs Full Duplex. I've also disabled QoS, and still no change. Not sure what else to do.
When directly connected to the modem everything seems fine. The modem is also the provided Motorola SBG6580 which I have called Time Warner to set the modem into bridge mode and have the DIR-655 connected to it.
With DIR-655 connected to PC
With Modem connected to PC
I'm thinking of purchasing a Cisco Linksys EA6500. I need a router that can one monitor bandwidth used by device. Keep exceeding our ISP's network bandwidth allocation, need to identify the devices that are causing this high usage and be able to do so from the router. Does the EA6500's standard software support this, is their router software one can obtain for the unit that does this or is there another home router option that can perform this function?
View 6 Replies View RelatedI have 2 computers on a network, and 3 devices that use wifi on the same network. Basically when ever computer A is connected, every single computer or device on the network runs extremely slow, if at all. I get anywhere between 1200-2000 ping on pingtest with 2-60% packet loss. Even the speed on the "infected" computer A downloads extremely slow. I'm at a loss for this problem, everything runs slow and its because of the one computer connected to it. I have virus software on this computer, but its not the best so i'm not ruling out malware or viruses right off the bat.
Devices: Blackberry, Iphone, macbook (all wifi)
Computer A
Runs windows xp 32 bit,
amd processor
onboard video
[code].....
The internet modem runs to a router (Dlink dir615) then to a switch (or hub, if you will) and then to the 2 computers. The entire problem is solved by unplugging computer A from the system. But other than that I have no alternative.
I am a new network admin at my company, and I am investigating a problem that is on a network designed by someone no longer here. So, I can't ask why things were set up the way they were. Anyway, here's the issue:
We have 50Mbps WAN connections between locations. The WAN devices are 3750s, but the port plugged into the providers network is a layer 3 port. Config is below for one of the ports: [code]
So, these are Gig ports, but our service provider limits to 50Mbps. When we do a data transfer, we can't exceed about 20Mbps total on the circuit. The data transfers at maximum 15-16Mbps.
I'm not familiar with QoS. I've tried to read more about SRR, but don't understand it well enough to know. Are the QoS settings creating this restriction? Our provider swears that the bandwidth is allocated and its not being choked on their end. I have not taken off the QoS config to test it that way because I'm not 100% sure if its needed and serving some purpose. I don't want to break something in order to fix this.
Is the QoS causing this? Do I need to put a bandwidth statement on the port? Should we be using routers and LLQ?
I purchased a WRT610N router early this month, the wireless network was working completely fine when I first set it up. Today I tried to connect my laptop to my wireless network. The laptop isn't able to connect at all. I also got a Sony PSP which has WLAN on and that saying it cannot detect any access point which would be my router.
View 3 Replies View RelatedHow can I open the Nat for both systems on my single router.
View 2 Replies View RelatedI was told that this router would push the PoE to the WAP4410N. I hooked the AP up to port 1 and no lights or anything... The network is all cat6, patch cords are cat6 shielded if this matters at all... what am I missing.
View 3 Replies View RelatedIs it possible to have 2 hard drives connected to a WRT610N perhaps connected through a USB hub?
View 1 Replies View RelatedI have the Linksys WRT610N wireless router and would like to know if it is possible to block all domains ending in .XXX? The access restrictions let you type in a 'specific' URL, but using a generic domain name doesn't seem to work. I basically want to block all access to any URL that ends in .XXX.
View 5 Replies View RelatedI just bought a certified refurbished router. The model is WRT610N-RM. Where's what I've done:
1. Downloaded newest firmware from the site using old router, Then disconnected. Connected a lan cable to the new router. Powered up the router. Held down reset untill the light blinks. Went to the browser and typed 192.168.1.1. Entered password to go into router and upgraded firmware. 2. 5 Ghz Settings: Went to Wireless menu. Selected "manual", mode is "mixed" (If i chose N only for 5 Ghz, then It won't save my setting for internet security. Instead it will be "disable" no matter what". The rest was default. SSID is enabled. Then I set up the 2.5 Ghz. I have 3 other computers with N wireless card. Some others have G, however when I viewed available networks, I only see the 2.4 Ghz ssid. I tried to reboot and unplug power for 10 seconds, but no luck seeing the 5 Ghz.
ive tried all types of things i read online and it is stuck on moderate no matter what i do, im hooked into router directly, when i hook directly into modem it switches to open.
View 2 Replies View RelatedI have a Cisco 871w that has been a very great product for many years. I recently switched to Windows 7 x64 on my main machine and now i am having all sorts of issues with it.. I have done a bit of research and found that it appears that it might be the firewall on the SDM that is causing the slowness issues. what does happen is that downloads from known good sites will run really slow. If i hook up my Macbook Pro or my Windows XP laptop i have no issues at all. i have tried Disabling IPv6 as well as SMB2.0 and this has not resulted in a fix at this point.
View 4 Replies View RelatedI am finding it impossible to set up port forwarding. No matter what I do I remain completely stealthed when I do a port probe via [URL]... The only way I seem to be able to open a port is if I enable remote management. When I do that, whatever port I specifiy as the remote management port is then fully open. Obviously, I can't leave a port exposed like this and, anyway, I need to open multiple ports for my purposes.
View 9 Replies View RelatedI have had no problems with my WRt610N fo 2 years. Yesterday a problem occured and today again. Namely, I opened my laptop (the lid) and suddenly it could not see my network (SSID) among the rest of the neighbouring ones. The WiFi indicator in the tray showed the yellow "!". Since I have another (secondary) router wired to the primary (WRT610N) I tried and succeeded to connect to it (same SSID, but type "g").
Today the same situation. This is the straneg thing - if I 1st connect to the "g" router after a while the WIn7 reports my SSID being of type "gn" meaning it now sees the primary WRT610N. If I switch off the secondary the netowork is maintained by the primary router showing "n". It seems like my laptop cannot see my router (but can see all other networks) until it 1sr connects to the secondary, and afterwards it sees the primary router and can stay with it.
Is LinkLogger the only option for reading logs on the WRT610Nv2? I read about Linksys's own software called LogViewer 1.14 but I can't find it.
View 3 Replies View RelatedI've been really stumped when I decided to start using xbox live. When ever I try to join my friends party I am slammed with a NAT error. For years now I have not been able to forward ports at all. Any port checkers come back with unable to contact your router.I am fairly certain its the router because, I directly plugged my 360 into my modem and everything worked like a charm.I've read on a similar post found here "Similar post" that updating the firmware might fix the issue?
View 9 Replies View RelatedI am trying to filter a URL, facebook and it is not working. I have tried rebooting the router and it is still allowing access. I have provided the settings and ranges for PCs.
View 3 Replies View RelatedMy WRT610n went out today for no apparent reason.All of my other peripherals are still running, but the router won't turn on. I've tried different transformers, outlets and powerstrips, with no luck -- no power. I've also tried a hard reset on it, with no luck.
View 3 Replies View RelatedHow is it possible to block facebook (or other sites) on WRT610N router, given that I have already set up Internet Access restrictions based on day/hour ?
View 9 Replies View RelatedAny success with a recent vintage Macbook Pro connecting to the 5.8Ghz channel on a WRT610N. I can connect with the 2.4 channel without a problem but I cannot maintain a connection on the high channel. Linksys support told me that the hardware was not compatible with the high channel.
View 3 Replies View Related