My new HP Touchpad 32 GB is causing my E4200 to reset. I can duplicate the issue by simply access the HP App Catalogue. I upgraded the firmware from 1.01 to 1.03 build 13 and the issue still exists.
View 1 RepliesI set up an E1200 about two weeks ago to replace our old DI-524 because our net speeds were getting throttled (the old router wouldn't support anything higher than 10mbps). The same day, we started getting modem resets (We have an SB6120). This never happened on the old router but it's constantly happening with this new one. It'll happen multiple times a day. I called Cox Tech Support and they pushed an upgrade onto the modem but it still reset. I don't think it's the router, since I don't understand why it would force the modem to reset, but this never happened before I installed it. The firmware is updated to the latest version on the Cisco site (1.0.02).
View 5 Replies View RelatedIf my computer has been sitting for a while without using the internet and i open my browser the dsl and internet lights on my router shut off for about 15 seconds and no one in my house has internet and then it turns back on. this ONLY happens when it has been sitting for a while with the browser closed and my computer is the only one that makes it do it. also i don't have my computer set to sleep after a certain time, my monitor turns off after 5 minutes and that's it. i have a siemens gigaset se567 and my isp is telus.
View 1 Replies View RelatedI just bought an E4200 and it was working perfectly, very easy to install, all that it promises. Then I had an energy peak. For some reason, don't ask me why, I did RESET the router not thru the web nor thru Cisco Connect, but pushing the reset button at the back. I can't access the router anymore ! It keeps asking for a password that is never accepted. I have uninstalled cisco connect and tried again. Nothing. The router is not found. Keeps asking for a password. I tried everything: blan+admin, admin+admin, the password I used to have (provided at the cisco connect uninstall).It seems that the RESET never worked. The router is working thru cables, meaning when I can connect to the internet wired. But the router is never found wireless.How could I update the firmware if the router is not recognized (or if I don't have a username+password) ?
View 9 Replies View RelatedDue to password loss, I get to reset the E4200 to factory default in order for router re-config.After pressing the reset buttom for 10sec, the router reset. After then, I could not access the router via browser with 192.168.1.1 at URL entry. My PC IPv4 setup: 192.168.1.11; subnet=255.255.255.0.But, ping 192.168.1.1 from PC was OK without packet loss. So router was restored with 192.168.1.1 and cable connection was OK.
View 2 Replies View RelatedI have an e4200 with the latest firmware 2.1.39. I just upgraded the firmware due to connection issues with my DSL. I now have the same issues with disconnects but I believe they are being caused by a different issue. When I try and log into my router through the IP address it wont let me, it says it can't find the router. Eventually after getting in the first time by using the default password, I have twice found out that all my settings are gone. This has happened twice this week and only happened after upgrading the firmware but I can not tell if firmware is causing it or if it is hardware related. I now reboot and restore saved firmware but that is a hassle and am pretty sure that is not the way it was designed to work.
View 9 Replies View RelatedI flashed the firmware and the ipv6 automatic is on disabled and I cannot set it to enabled.the 6rd tunnel option I can change but that has not effect- in fact from what I looked up it seems to be something used by some cable providers.hate to have to reset the router to factory defaults and then reset the network up - just to see if i can get the option to set IPV6 auto to enabled.
View 3 Replies View RelatedOne of the many things that I liked about the e4200 over my olg 54GL was the fact that I could reboot it remotely. However, I've recently had a few problems that only a full power down would fix. In addition, I've noticed that the DCHP client table doesn't reset when I do a soft reboot. Is this intentional? Is the soft reboot not really a full reboot? Can it be made a real reboot?
View 7 Replies View RelatedBasically, my issue stems from the latest Boxee firmware from 2 weeks ago, that since then, its been causing my DIR 655 to reset itself, thereby disabling my whole home internet. It eventually turns back on again after a while, but the process doesn't stop.Basically, my DIR 655 is connected, hard wired to my boxee. I also have a NAS 323 hard wired to my router. I've had this setup on my boxee, reading all my movies/shows from my NAS without any issues for the past 10 months. Then the firmware from 2 weeks ago on the boxee started to cause my router to reset. I thought it was a hardware router failure, so I bought another of the same model to try that out, same thing happened though. When I rolled back my boxee firmware to the previous version, it no longer causes my router to reset.Now, besides me trying to figure out how to correctly block the boxee from updating on the router. Is there anything I can do on the router to tell it to prevent it from letting the boxee forcing it to reset? I'm on High Speed DSL. My internet provider modem is acting as a bridge to my DIR 655. Its been working fine for the past 10 months.
I've also done the following:Ensure DNS IP addresses are being filled in under Setup/Internet/Manual? You can find thse under Status/Device Info/Wan section. Turned off ALL QoS Turned off Advanced DNS Services if you have this option under Setup/Internet/Manual.Turned on DNS Relay under Setup/Networking.Setup DHCP reserved IP addresses for all devices on my router.Ensure devices are set to auto obtain an IP address.I have Set Firewall settings to Endpoint Independent for TCP and UDP..
Basically, I've put my boxee back to my previous firmware, and this doesn't cause my router to reset and disable my internet. But I don't get how/why a firmware update can trigger my router to do this?
Since recently replacing my home router with a Linksys E2500, I have been getting Blue Screen of Death (BSOD) with my Company's VPN (AT&T). It only happens when I am running wireless with my E2500. If I am hooked up to my E2500 through a ethernet cable it doesn't happen. I have updated the BIOS on my Lenovo Thinkpad T410 and ensured all of my drivers are up to date. I am 99.9% sure the problem is caused by my Linksys E2500 because I have used my laptop on other wireless routes at work and school and never get this problem. I am also ensured that my E2500 has the current firmware installed and upgraded my Company's VPN to the most current level to no avail.
I am getting DRIVER_IRQL_NOT_LESS_OR_EQUAL Blue Screen of Death in agnfilt.sys.
For some reason, I have been trying to use QOS for several network related jobs (VPN, streaming). It would seem that when QOS is enabled and the appropriate ports are set which a high priority, the speed of my connection drops to a crawl. When I disable QOS, I'm flying again. I have confirmed ports, and protocol types (TCP or UDP) and nothing seems to work.
View 2 Replies View RelatedI just bought a Samsung BD-D5300 Blu-ray player that allows a bunch of networking options including wireless and wired. I was using the wired option when I came across some conflicts with my network using a Linksys WRT350N v1. The Samsung conflicted with the Linksys's DHCP server. The blu-ray player turns off automatically when inactive. It was causing conflicts with my iPad 2, MacBook Pro and Motorola Atrix android phone whenever it got assigned an IP address. When I reset the router and my cable modem, it wasn't assigned an address for awhile, which fixed things, but as soon as it got an address again, it was caused conflicts by being seen as a LAN by my router. When it wasn't receiving an address, it got the automatic private IP address of 169.x.x.x. When I removed the connection with my router, the conflicts disappeared and my computers were able to access my wifi again.
View 1 Replies View RelatedI've had an E4200v1 in use as my home's main router for about 3 mos. And while many others have reported disconnect problems (I think), I myself have never seen any. My router and its N & G wifi networks have been rock solid. Until yesterday that is.Now all of a sudden, most of my family is complaining about wifi disconnects, slow speeds, etc. (My primary PC is hard-wired so I don't see any problems whatsoever... the problem apears to be wifi-only)And the Apple devices (OSX & IOS) seem to have the most severe problems. But Windows devices have also seen problems, just not as critical.Also, it's worth noting that I've been running 1.0.04 the whole time, without any problems... it seemed relatively stable to me. That is until yesterday.
I've bounced the router, I've disabled/re-enabled Wireless G network. I've switched mode from "mixed" to "G-only" back to "mixed". I've changed the channel width back to the default of Auto (I had been using 20Mhz), which increased my throughput (as measured by Qcheck) so I'm leaving it "Auto".
I have an E1550 less than 1 year old. Lately, I have been losing internet on the AT&T modem. I called AT&T but as part of their diagnostics, I have to plug the modem directly into the PC. I have loaded the latest firmware to the E1550.Lose Internet but wireless connectivity to router exists.Internet light on modem is out (modem is connected to router)Unplug modem and leave off plug in, internet light is still out.Unplug router, plug router back in - no internet connection but do have wireless connectivity to router.Take cable from modem to router and plug directly into PC internet light comes on in modem and I have internet from PC.Take cable from PC and plug back into router .I have internet via wireless.What I can't figure out is what could be happening in router that would impact modem internet connection. I have replicated this at least 3 times. Yes, the modem is a bit old, but since plugging it directly into the PC works, I'm thinking it has to be the router and I cannot figure out why unless there's some sort of electrical thing going on in the router.
View 4 Replies View RelatedI work from home on a Lenovo Laptop. I connect to my work network, and ultimately to a midrange ISeries. For the past year I've had no major problems with my Netgear Linksys WRT54G. I switched to a Netgear N300 last weekend because my husband's desktop was having a lot of issues. His connection is much better now.I'm able to connect to the internet with no problem, and I can access my company network & email pretty well. But, when I log on the ISeries it slows to way less than a crawl. According to my netwok icon, the connection is anywhere from 104 to 130 MBPS at any given time. But it freezes up so badly that it takes about 20 - 30 seconds just to type each letter, or to go from one window to another, or just to move the cursor down one line. It's infuriating. Every once in awhile if I disconnect and reconnect it works almost normally for awhile, but eventually slows down almost to a stop again. I actually worked for about 90 minutes the other day with no problem before it started acting up again. When I put the old G router back it works fine again. My laptop has an Intel(R) Centrino(R) Advanced-N 620 wireless adaptor. As long as I don't connect to the iseries, I have good speed and no issues with the internet or work intranet.
View 1 Replies View RelatedI'm thinking of purchasing a Cisco Linksys EA6500. I need a router that can one monitor bandwidth used by device. Keep exceeding our ISP's network bandwidth allocation, need to identify the devices that are causing this high usage and be able to do so from the router. Does the EA6500's standard software support this, is their router software one can obtain for the unit that does this or is there another home router option that can perform this function?
View 6 Replies View RelatedSo I just bought and recieved a new computer with the wireless WMP600N.
I turned the computer on and a had small lags every 5th second or so which, even though they are small, are pretty annoying. I then tried to look for a reason as to why this happens and what i found out was that if a turn off the wireless internet connection the lag spikes stops and if I turn it on they occour.
My computers specs are:
I7 2600k 4x 3,40ghz
Nvidia geforce GTX 570
8 gb 1600mhz RAM
WMP600N wireless-N PCI
Windows 7 64xbit
I've got a Dell N5010 with Windows 7, after dropping my laptop and breaking the hard drive I replaced it with one I bought from Amazon, all is well apart from I now have to use an external antenna for WiFi to work. Without it I just get ' No connections are available'. I also can't turn off the touchpad with the button to the right of F12 like I used to. I read somewhere it might be to do with the Dell Drivers CD?
View 1 Replies View RelatedIve set my laptop to stay on when the lid is closed. Now when i do close the lid, the touchpad reacts to the screen and starts doing all sorts of crazy things, zooming in and out, moving the taskbar around, opening things and deleting things.Ive resorted having to place a cloths or kleenex folded in half over the touchpad when i close the lid. ive also disabled the touch and used a mouse and no problems. I have updated the drivers and dell toucpad, ive even uninstalled everything and installed the synaptic drivers and touchpad software.. Yet another problem with the l521x.How can i fix this? maybe the touchpad is defective and has to be replaced?
View 10 Replies View RelatedI previously entered in settings for the "Static DNS" 1 through 3 (using ip addresses from OpenDNS and one from Google DNS).
I want to remove these so the router reverts to using the DNS allocated to it by the ADSL modem (which will likely be the IP of the modem, which then forwards the requests to the DNS from the ISP).But I can't clear the Static DNS settings. I have to put in 0.0.0.0 but the last zero is not accessed. I get the error: The value is out of range [1 - 254].So I end up with 0.0.0.1 and then all Internet access is lost on the computers because they are being given a bad DNS IP.
How can I reset the static DNS ip address back to 0.0.0.0 ?
My linksys router reset itself. Yes it reset itself. It resets to default paramaters. I had to change the router parameters in the webpage with the wired connection to the router. That works fine, but after a day or say it comes back to default again. I am going crazy, I am sure nobody is pressing the little button on the router. Do I have virus or something or maybe the router is going bad. It's a WRT54G.
View 2 Replies View RelatedHow to reset the linksys cisco wrt120n router.
View 4 Replies View RelatedI am facing issue with my cisco wireless E1000, the wireless connection on the laptop reset on its own. Its like there is a timer and it reset's the wireless connection after some time. I was unable to measure the time after which it resets but its happening too frequently causing multiple internet apps to fail example if I am downloading something it will fail as the internet connection is reset. The firmware I am running on the rotuer is 2.0.01 and I have configured DHCP on the LAN, I am experiencing this problem with 3 laptop that I use at home which uses both G and N networks.
View 4 Replies View RelatedHow will I reset WRT 160N?
View 1 Replies View RelatedHow To Reset E2500 Router
View 1 Replies View RelatedI want to use my router to boost the signal to the 2nd floor of my house, and Im having some problems.When I connect my router to the web application to change restore it to manufaturer setting the router keeps broadcasting my old SSID. The laptops in the house pick up that signal. I want to reset my router so it can broadcast my new network.
View 2 Replies View RelatedI recently set up a wrt54g router that I got used from a friend. I pressed the 'reset' button on the back, configured it for my computer according to the instructions on the website, and everything worked fine for a couple of days. Then I lost connectivity, tried powercycling my modem, but had to reset and reconfigure the router again. Worked fine again for a couple of days, then the problem repeated itself, so I reset and reconfigured again.
View 1 Replies View RelatedThis router was given to me without any documentation. No one knows what the password is for the wifi or web interface. I have tried to reset the router to factory defaults without any luck. I have tried regular reset method and 30/30/30 and still it is holding on to the custom settings. Here is what I know:
1. The router can be pinged without any errors.
2. The logon screen comes up requesting username and password. I have tried all of the default inputs (blank/admin, admin/admin).
3. The wireless is working and the SSID is Linksysxx.
4. I tried the following:at the DOS prompt typed cd then, TFTP -i 192.168.1.1 PUT (my fw).binunplugged the router, plugged in and hit "Enter"After about 15 seconds I got the error message, "Invalid Password". I tried this again and got the same results.I know the router is working, but I can not get it for go back to factory settings.
I am facing issue with my cisco wireless E1000, the wireless connection on the laptop reset on its own. Its like there is a timer and it reset's the wireless connection after some time. I was unable to measure the time after which it resets but its happening too frequently causing multiple internet apps to fail example if I am downloading something it will fail as the internet connection is reset. The firmware I am running on the rotuer is 2.0.01 and I have configured DHCP on the LAN, I am experiencing this problem with 3 laptop that I use at home which uses both G and N networks.
View 2 Replies View RelatedI can't seem to login to my admin. the IP for me is 192.168.0.1 and I can't login. I tried resetting the router a few times and no luck.Is there ANY other way to reset the username and password?
View 6 Replies View RelatedI forgot it. How do I either find out what it is, or reset the E1000 so I can create a new one? (Connection now working fine. Held the reset button for 30 seconds, and conmnection pops right up again.
View 4 Replies View Relatedi'm attempting to access the router's configuration options (192.168.1.1) and it's requesting a user and a password, i have not set any of them so i'm using the defaults, been, user (blank), password (admin) but is not taking them; after 3 attempts it gives me a 404 error.
View 6 Replies View RelatedI have a wrt120n router. It will not give IP addresses after 24 hours of usage. Having to reset the router to be able to get connectivity is getting to be very aggravating.
View 2 Replies View Related