D-Link DIR-655 :: Boxee Causing It To Reset And Disabling Internet?

Oct 28, 2011

Basically, my issue stems from the latest Boxee firmware from 2 weeks ago, that since then, its been causing my DIR 655 to reset itself, thereby disabling my whole home internet.  It eventually turns back on again after a while, but the process doesn't stop.Basically, my DIR 655 is connected, hard wired to my boxee.  I also have a NAS 323 hard wired to my router.  I've had this setup on my boxee, reading all my movies/shows from my NAS without any issues for the past 10 months.  Then the firmware from 2 weeks ago on the boxee started to cause my router to reset.  I thought it was a hardware router failure, so I bought another of the same model to try that out, same thing happened though.  When I rolled back my boxee firmware to the previous version, it no longer causes my router to reset.Now, besides me trying to figure out how to correctly block the boxee from updating on the router.  Is there anything I can do on the router to tell it to prevent it from letting the boxee forcing it to reset?  I'm on High Speed DSL.  My internet provider modem is acting as a bridge to my DIR 655.  Its been working fine for the past 10 months.

I've also done the following:Ensure DNS IP addresses are being filled in under Setup/Internet/Manual? You can find thse under Status/Device Info/Wan section. Turned off ALL QoS Turned off Advanced DNS Services if you have this option under Setup/Internet/Manual.Turned on DNS Relay under Setup/Networking.Setup DHCP reserved IP addresses for all devices on my router.Ensure devices are set to auto obtain an IP address.I have Set Firewall settings to Endpoint Independent for TCP and UDP..

Basically, I've put my boxee back to my previous firmware, and this doesn't cause my router to reset and disable my internet.  But I don't get how/why a firmware update can trigger my router to do this?

View 6 Replies


ADVERTISEMENT

Computer Causing Router To Reset

Aug 31, 2011

If my computer has been sitting for a while without using the internet and i open my browser the dsl and internet lights on my router shut off for about 15 seconds and no one in my house has internet and then it turns back on. this ONLY happens when it has been sitting for a while with the browser closed and my computer is the only one that makes it do it. also i don't have my computer set to sleep after a certain time, my monitor turns off after 5 minutes and that's it. i have a siemens gigaset se567 and my isp is telus.

View 1 Replies View Related

D-Link DIR-655 Causing Internet Slow Downs?

Jun 10, 2011

I have been using my DIR-655 for about 2 weeks now with Road Runner wideband services. Starting yesterday my internet became very slow and I discovered the cause was the router. I tried resetting it to factory settings and things will be fine and run smoothly for about 5-15 minutes but after that it goes back to being extremely slow. My speed tests would go from 10ms (normal) to 250-450ms. Before this issue occurred the Dlink was perfect, had full speeds. I am running a wire Ethernet connection.

I am currently using revB and tried upgrading firmware to 2.01NA which had no effect, but make my internet seemingly go back to normal for the first few minutes then nosedive again.I have also changed my speed/duplex settings in Network Config to 1gbs Full Duplex. I've also disabled QoS, and still no change. Not sure what else to do.

When directly connected to the modem everything seems fine. The modem is also the provided Motorola SBG6580 which I have called Time Warner to set the modem into bridge mode and have the DIR-655 connected to it.

With DIR-655 connected to PC

With Modem connected to PC

View 5 Replies View Related

D-Link DIR-825 :: Disabling Internet Sessions Logging

Jan 17, 2012

There is a page in the DIR-825 that logs your computers IP and the other IPs it is connecting to. I was wondering if there was a way to disable that function on select devices? My handhelds and legitimate computers that should be on the internet are filling it with spam and it is hard to check for unauthorized users on the network. If that is not possible, then would I be able to completely disable the feature?

View 1 Replies View Related

D-Link DIR-615 :: Router Causing Slow Internet Connection

May 11, 2011

This only started about a week ago and everything was working fine before then. My router is causing my internet to be slow (I know this because it goes at normal speed when I am connected directly to my modem)

View 1 Replies View Related

Linksys Wireless Router :: E1200 Causing Modem To Reset?

Nov 28, 2011

I set up an E1200 about two weeks ago to replace our old DI-524 because our net speeds were getting throttled (the old router wouldn't support anything higher than 10mbps). The same day, we started getting modem resets (We have an SB6120). This never happened on the old router but it's constantly happening with this new one. It'll happen multiple times a day. I called Cox Tech Support and they pushed an upgrade onto the modem but it still reset. I don't think it's the router, since I don't understand why it would force the modem to reset, but this never happened before I installed it. The firmware is updated to the latest version on the Cisco site (1.0.02).

View 5 Replies View Related

Linksys Wireless Router :: HP Touchpad Causing Cisco E4200 To Reset

Jul 6, 2011

My new HP Touchpad 32 GB is causing my E4200 to reset. I can duplicate the issue by simply access the HP App Catalogue.  I upgraded the firmware from 1.01 to 1.03 build 13 and the issue still exists. 

View 1 Replies View Related

TP-Link ADSL2+ Wireless :: TD-W8970 - TP-LINK USB Printer Controller Is Causing BSOD?

Apr 12, 2013

Region : Portugal
Model : TD-W8970
Hardware Version : V1
Firmware Version :
ISP :

Two week ago I bought the TD-W8970 ADSL router model. Im using a canon pixma IP4700 printer connected to the router USB print server port and everything is working without any issues if I just look to the router functionalities.

However since that Ive installed TP-LINK USB Printer Controller, my both computers (desktop with windows 7 and laptop with windows 8) are getting very often some BSOD.

I was editing all files automatically generated by windows on this cases and if seems that the cause of this issue is the file TplinkUDSMBus.sys (installed by USB Printer Controller).

To check the impact of this, Ive uninstalled the TP-LINK USB Printer Controller software from my laptop and I dont have any BSOD since 5 days ago. In the desktop Im still have the same issue.

The router print server is a nice functionality and I really want to use it.

View 1 Replies View Related

D-LINK DSL 2730B - Reset Router To Get Internet Speed Back To Normal?

Jun 12, 2013

I have a router that needs to be reset to get the internet speed back to a usable speed. It is a fairly old router (D-LINK DSL 2730B) and it does get quite annoying. There is allot of devices connected, which may affect the speed, but I am sure it shouldn't change upon reboot. I literally reboot every hour or 2 during peek periods.

View 1 Replies View Related

D-Link DIR-655 :: Causing Excessive Battery Drain On Android Phone

May 19, 2011

I've got a Samsung Epic 4G and whenever I leave the wifi connected on my phone at home, it seems to never go into sleep so the battery drains overnight doing nothing.  If I turn off wifi and leave it on the 3G network, battery barely drains at all.  Is there something in my router that could be keeping my phone awake when it's connected.  I've tested it on a friends wifi network and my phone sleeps just fine, it's only when I'm connected to my DIR-655. 

View 12 Replies View Related

Disabling Internet To Other Computers?

May 20, 2011

I have a modem connected to my pc, and the ethernet can be removed and connected to a laptop to access internet. How do I prevent access to other laptops and computers?

View 4 Replies View Related

TP-Link Dual-Band Wireless :: WDR4300 - Disabling Broadcast Of Manufacturer Name?

Mar 21, 2013

Canada
Model : TL-WDR4300
Hardware Version :
Firmware Version :
ISP : [/COLOR]

Model : TL-WDR4300
Hardware Version :
Firmware Version :
ISP : [/COLOR]

Is it possible to disable broadcasting that the WDR4300 is made by TP-Link? I want to continue to broadcast the SSID but not the manufacturer. I have looked in the various menu pages and cannot figure out how to have this happen.

View 14 Replies View Related

D-Link DIR-655 :: Disabling DHCP On Arris Router And Setting Static IP Address

Sep 9, 2012

My old modem from Roadrunner (Time Warner) died and the service man replaced it with a Arris TG852 modem/router. then my problems began. I would like to have the Arris modem act like a modem and not a router. The network governed by the DIR works fine but none of the clients can connect to the internet. Below are the steps I have tried.in both steps below, The DIR is connected to the Arris using the Ethernet not the Wan port.

1. I tried disabling DHCP on the Arris router and setting a static IP address for the DIR router. This worked for a bit and then quit. Some of the computers said there were duplicate IP addresses on the network. If fact the same IP address showed up in the DNS list of the Arris and the DIR routers.. even though the Arris router had DNS disabled.

2. After reading other forums. I enabled DHCP on the Arris and set it to passout IP address between 192.168.0.2 and 192.168.0.99. I then setup the DOR to pass out addresses between 192.168.0.100 and 192.168.0.200. then moved the DIR into the DMZ of the Arris. Still no access to the internet.

View 2 Replies View Related

Ethernet Not Detected Causing No Internet?

Jul 21, 2012

For starters I have a qwest m1000 modem and a netgear router.this morning there was a rather large thundestorm that caused my power to cut out while I was usin my computer.. once I got it back up and running the ethernet light on my modem wasn't liighting up.I reallly have no idea what to do. Everything but the ethernet is working. I can still get to my routers website but that's it, and I don't what to do there once I'm on it.Is it possible the storm messed up the settings? Or killed part of my pc/modem? On my computer the ethernet light next to the jack on the back is yelllow when its threw my rouuter, but when I plug my modem into it directly it doesn't light up at all.

View 5 Replies View Related

Disabling Internet On One Computer In A Network?

Dec 12, 2011

I am a teacher in a computer Classroom. We are on a school network and certain students abuse the internet privalages. Is there a way for me to restrict the internet for a certain computer in the network besides unplugging an ethernet cord?

View 2 Replies View Related

DWA-125 - PS3 Causing PC To Lose Internet Access

Jul 27, 2011

I've recently added a desktop pc to the home's wireless network (using a D-Link DWA-125 Wireless N 150 USB adapter rev.A2) and it used to play nicely with the other devices. After switching out the router to an Actiontec V1000H my computer has begun losing most connectivity when the PS3 is turned on.

The pc still sees the network and there is a little activity there it seems. Everything runs fine when the PS3 is off and in the Wireless Network Connection Status display the speed is usually listed at 65-75 Mbps. But when the PS3 is turned on it reads 6.5 Mbps with the IPv4 connectivity bouncing between "internet" and "limited". Windows' automatic diagnosis is "Cannot communicate with DNS server".

I tried assigning static IP addresses to the pc and ps3 thinking there was a possible IP conflict with the dynamic addresses. Thinking there could be a conflict with ports I read up on port forwarding but my knowledge of networking is limited and I'm not even sure if that is the problem.

There are alot of other devices connected, 2 laptops, 2 iPod touches an iPhone the PS3 and now this old desktop clunker. I figure it's possible that the router is getting overloaded with everything and the PS3 just pushes my computer's bandwidth out the window but I would think that there would be some noticable drop in performance on the other laptops as well, which there hasn't.

View 19 Replies View Related

TP-Link Dual-Band Wireless :: TL-WDR3600 USB Print Server Causing BSOD

Mar 15, 2013

Region : UnitedStates
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : 3.13.26 Build 130129 Rel.59449n
ISP : Charter

I've set up my printer (HP PSC 2410) to the router using TL-WDR3600_V1.0_USB Print Service Client Setup and that part's fine. The USB Printer Controller sees the printer as an "auto-connected printer" and I can select the printer as my default to print to. My problem lies with the fact that every time I try to print something, it causes a BSOD. I'm using Windows 8 and checked to make sure the USB Print Service Client Setup program was compatible with Windows 8 before I attempted anything. The HP PSC 2410 printer is on the Print Server Compatibility list so I don't know why I'm having problems.

The error I get each time I try to print is: SYSTEM_SERVICE_EXCEPTION (TplinkUDSTcpBus.sys). One of the draws of this router was that I could hook up my printer via USB and print wirelessly

View 4 Replies View Related

Disabling Internet Access On Certain Switch Ports But Not Others?

Oct 12, 2011

I have a central cisco SG200 26P switch, with about 20 ports going off to other network switches, and individual computers around the building.I need to keep the LAN functionality of the network, but I need the majority of the computers to not have internet access. But I also need to be able quickly re-enable internet access for a particular computer connected to a particular port if required.

View 3 Replies View Related

Router Causing Slow Internet Connection

Jan 3, 2013

decided first of all to connect an old router to the master (but not test) socket together with different cabling & splitter/microfilter - everything starting working almost perfectly (apart from downstream data rate was considerably lower than expected each time I connected - between about 1400 & 1600 Kbps - I have max. 8 Mbps).when I connected back my current router everything continued to be OK (apart from low downstream data rate) - until I would restart the current router and everything went back to very very slow.

View 5 Replies View Related

After Disabling / Enabling Connection - Internet Lost?

Feb 4, 2011

I no longer have internet access from my home network ONLY on my desktop computer. Everything was working fine as always - then while I was in my Network and Sharing Center, and clicked on my ethernet connection, 'Local Area Connection 3', I accidentally disabled it. No big deal I thought, so I re-enabled the connection. Except for some reason, my connection is all screwed up now. The name of this connection was and always has been 'dkm2' and now it just says 'Network', with no internet access. I have unplugged the cord and plugged it into this laptop and it immediately recognizes 'dkm2' and connects flawlessly, so I know the problem is on the desktop computer's end, and not the cable or router. I have tried reinstalling the ethernet adapter, as well as reinstalling/updating all drivers for it.The network diagnostic tool turns up with a message that says the connection between either my ethernet adapter or router and the Internet is broken. No matter what I seem to try, I can't get my connection to go back to it's normal 'dkm2' connection and stop giving me a generic, disconnected 'Network'. I can't figure out what could have changed. All that happened was the disabling and enabling of Local Area Connection 3.

View 9 Replies View Related

New Computer Causing Internet To Die On Entire Network

Aug 6, 2011

After recently setting up a new computer, my entire network seems to randomly loose internet connection. The interval between connection losses is as short as half an hour but it sometimes goes several hours without dying; the connections is lost for anywhere between 30 seconds and 20 minutes each time it dies.The new computer is running Windows 7 and is using a Roeswill USB wireless adapter, but I have tired it with a wire and the connection still dies. I am disinclined to believe that this is caused by a virus simply because this is a brand new computer that has had only minimal use; to be on the safe side, though, I did do virus scans with multiple programs, however, I did not find anything.When the connection is lost, a yellow exclamation appears on the task bar's internet access icon. If I check my available networks, my network still shows full strength. I have tried disconnecting and reconnecting but nothing happens; I don't get any "failure to connect" type errors nor do I get connection back. I have also tried physically removing the adapter/wire and plugging it back in, but that doesn't do anything either.

I am under the impression that the new Windows 7 computer is doing something to temporarily kill the entire network, but I don't know what.For the record, my modem is an old Motorola and my router is an old Netgear. Both are quite a few years old, but I don't think they are the problem as my internet was fine before I added the new Windows 7 computer. There are wired computers and wireless computers running XP, Vista, and 7 also on the network.

View 2 Replies View Related

Computer Causing Internet To Be Slow On Entire Network

May 4, 2012

I have 2 computers on a network, and 3 devices that use wifi on the same network. Basically when ever computer A is connected, every single computer or device on the network runs extremely slow, if at all. I get anywhere between 1200-2000 ping on pingtest with 2-60% packet loss. Even the speed on the "infected" computer A downloads extremely slow. I'm at a loss for this problem, everything runs slow and its because of the one computer connected to it. I have virus software on this computer, but its not the best so i'm not ruling out malware or viruses right off the bat.

Devices: Blackberry, Iphone, macbook (all wifi)
Computer A
Runs windows xp 32 bit,
amd processor
onboard video

[code].....

The internet modem runs to a router (Dlink dir615) then to a switch (or hub, if you will) and then to the 2 computers. The entire problem is solved by unplugging computer A from the system. But other than that I have no alternative.

View 5 Replies View Related

Computer Causing Router To Lose Internet Connection?

Dec 9, 2012

I have 2 laptops and 1 desktop all connected to the same router, the 2 laptops are connected via wifi and the desktop PC is currently connected via an Ethernet cable, both laptops run windows 7 while the desktop runs windows XP and more or less every time the desktop is booted after a few minutes of normality connection to the internet is lost and the yellow triangle on windows 7 appears so to fix this I have to go into my routers settings via 192.168.1.1 and reboot which then solves the problem and all machines function as they should including the desktop.

View 2 Replies View Related

Linksys Wireless Router :: E4200 - VPN Is Disabling Internet Access

Sep 26, 2011

I have a Linksys E4200 router with firmware version 1.0.02. I am using a Macbook Pro. I can connect to a VPN server with the default VPN client software, but it kills my internet connection and disables connecting to SMB

View 5 Replies View Related

Linksys Wireless Router :: E1550 Causing Modem To Lose Internet

Mar 29, 2012

I have an E1550 less than 1 year old.  Lately, I have been losing internet on the AT&T modem.  I called AT&T but as part of their diagnostics, I have to plug the modem directly into the PC.  I have loaded the latest firmware to the E1550.Lose Internet but wireless connectivity to router exists.Internet light on modem is out (modem is connected to router)Unplug modem and leave off plug in, internet light is still out.Unplug router, plug router back in - no internet connection but do have wireless connectivity to router.Take cable from modem to router and plug directly into PC internet light comes on in modem and I have internet from PC.Take cable from PC and plug back into router .I have internet via wireless.What I can't figure out is what could be happening in router that would impact modem internet connection.  I have replicated this at least 3 times. Yes, the modem is a bit old, but since plugging it directly into the PC works, I'm thinking it has to be the router and I cannot figure out why unless there's some sort of electrical thing going on in the router.

View 4 Replies View Related

Cisco Firewall :: Windows 7 And 871W / WSDM Causing Slow Internet And Downloads

Mar 8, 2011

I have a Cisco 871w that has been a very great product for many years. I recently switched to Windows 7 x64 on my main machine and now i am having all sorts of issues with it.. I have done a bit of research and found that it appears that it might be the firewall on the SDM that is causing the slowness issues. what does happen is that downloads from known good sites will run really slow. If i hook up my Macbook Pro or my Windows XP laptop i have no issues at all. i have tried Disabling IPv6 as well as SMB2.0 and this has not resulted in a fix at this point.

View 4 Replies View Related

D-Link DIR-825 :: How To Reset Router

Jan 22, 2013

my cable company tells me my router is not refreshing ?? even after i disconnect - reconnect ..the power   is the button on top with the circling arrows for refreshing it .. i do have a static IP if that makes a difference .

View 8 Replies View Related

D-Link DIR-655 :: Time Will Not Reset

Mar 4, 2012

I have DIR-655, 1.33NA. Recently, I noticed the clock in the router was off, so I wanted to correct it. Each and every time I go through the steps to reset the clock, using time server or clone computer time, or manual reset, after the save settings and reboot of the router, i find the router still displays the wrong time, and frequently reverts itself to a time on Feb 22, 2012. Same problem for trying to reset the DST settings, turning automatic time from server on and off, changing the time server polled. Additionally, I have forced the router to factory settings and rebuilt all of my configuration no less than 4 times.

So, since I recently had to trade out the cable modem because Cablevision fried it with their 'system upgrade', I'm also wondering if the same shenanigans also damaged the router.

View 4 Replies View Related

WBR-1310 D-link / How To Reset Password

Dec 23, 2011

I have a WBR-1310 D-link and was in setup this morning trying to fix my password cause the old one stopped working. Somehow I changed the password and no longer have access to the settings to change it to one that I can use to log on with my other wireless devices!!! Is there a way I can reset the whole thing? I mean something that makes sense to someone who is new to wireless internetting?

View 1 Replies View Related

D-Link DIR-655 :: Can't Revert Or Reset After 1.35NA

May 12, 2011

So, after everyone was raving about the 1.35NA version, I downloaded it.  As I always do, I disabled my wireless NIC and connected an RJ-45.  I saved my config to a .gws file.  I uploaded the new firmware.  When I went to reload my settings file, it said it was not a valid file.  I tried multiple times.  I even tried earlier versions of saved config files.  Same thing. 

So, I figured I'd revert to the 1.34NA firmware it was previously on.  It wouldn't take it.  So, I used the router config "system" page and chose "restore factory defaults".  It didn't work.  It still had the 1.35NA.  So, I used the router's reset button.  I held it in for 10 seconds, saw the system lights all blink in unison.  I checked the config page and it was still on 1.35NA. 

View 2 Replies View Related

D-Link DCS-942L :: Unable To Reset It

Jun 24, 2012

I initially set it up for static IP, which was a mistake for reasons I probably don't need to go into here.  Having recognized my mistake, I've been trying to hard reset it so I can convince it to acquire its IP address by DHCP, but each time I reset it and return to the "First, select your camera" screen in the setup wizard, I'm faced with a single choice: the device as I first set it up for static IP.  I don't seem to be able to convince it to give up that erroneous static IP address.I have read the FAQ section on hard reset.  I've held down the reset button for a lot longer than 6 seconds while the cam was connected to power and ethernet, and I've watched it go through the sequence of flashing blue reset and WPS lights until it settles down, but this doesn't change the situation, evidently.

View 7 Replies View Related

D-Link DIR-655 :: TCP Sessions Timing Out / Getting Reset

May 30, 2012

I am having a recurring problem with tcp sessions timing out / getting reset.  I'm using the DIR-655 with PPPoE on a Qwest DSL line.  Everything appears to be working fine (including my ipv6 tunnel) except for this issue where my long running ssh & database connections are being reset after a period of time.Currently have 2.03NA loaded, tried using 2.07NA but couldn't get ipv6 working correctly with the newer version.

View 7 Replies View Related

D-Link DIR-615 :: Wireless Setup After Reset?

Feb 23, 2011

I need to reset my 615 remotely.  I will have someone on the other end push the reset button.  I will then need to have them login to the 615 wirelessly. I'll establish a remote control session to their computer, and then I'll reconfigure the router settings. I know how to reconfigure the router just fine.

1) How long do you press the reset button, the manual says 10 seconds, is that correct?

>> 12 SECONDS

2) Once reset, is wireless turned on by default? I hope so, but the manual shows ENABLE WIRELESS unchecked... is that the default setting? Do I HAVE TO CONNECT VIA LAN CABLE TO "ENABLE WIRELESS" first?

>> YES

3) is the default ssid = "dlink" (no quotes)

>> YES

4) is the SSID invisible by default, or is it visible immediately after RESET?

>> IT IS VISIBLE AFTER RESET

The person on the other side can't access the router with a LAN cable, so once reset, the only way to get into the router will be via wireless; that's why I want to be sure I can do this before we do the reset.

View 5 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved