D-Link DIR-655 :: Time Will Not Reset
Mar 4, 2012
I have DIR-655, 1.33NA. Recently, I noticed the clock in the router was off, so I wanted to correct it. Each and every time I go through the steps to reset the clock, using time server or clone computer time, or manual reset, after the save settings and reboot of the router, i find the router still displays the wrong time, and frequently reverts itself to a time on Feb 22, 2012. Same problem for trying to reset the DST settings, turning automatic time from server on and off, changing the time server polled. Additionally, I have forced the router to factory settings and rebuilt all of my configuration no less than 4 times.
So, since I recently had to trade out the cable modem because Cablevision fried it with their 'system upgrade', I'm also wondering if the same shenanigans also damaged the router.
View 4 Replies
ADVERTISEMENT
Nov 29, 2011
At times when my laptop is running a dianostic it says maybe your DNS is haveing a problem. I don't know what a is DNS
View 2 Replies
View Related
Aug 31, 2012
Every time I switch on one of our laptops it will not connect, once the router is restarted it works fine. We have 4 other devices which happily connect to the wireless connection first time.
View 2 Replies
View Related
Jun 6, 2011
I am having a problem about the caller time out.#dialer idle-timeout 180 either..So the ISDN call will be disconnect after 180 sec.However even there is traffic on the ISDN line, it will disconnect after 180 sec.For example I PING -t command to the destination IP address, it will start dialing out after I run the PING command from srouce PC, but it will disconnect after 180 sec even continue to PING.I checked the remaining time by the command #show caller timeouts.It won't reset the remaining Timer parameter. [code]
View 4 Replies
View Related
Jan 10, 2012
AI have a Dir-825 router. The 5GHz is turned off and the wirless is on G/N. I have shawcable for my isp and my firmware is 2.06 and its a Rev B Router. I also have Qos Engine on for allowing me to have 2 xboxes on Open NAT.problem is my wireless signal for some wired reason is VERY weak. A while ago it used to work really far way outside. It was around 150ft distance at 4 bars. Now for some reason I can't even go upstairs without getting a 1 or 2 bar signal.
View 3 Replies
View Related
Sep 1, 2011
i have had my dir-655 one year now, have never had wireless problems with it until now.my notebook's internet gets very slow somedays, i just restart my router and then internet speed works normally.i have:
Hardware Version: A4 - Firmware Version: 1.32EU
View 5 Replies
View Related
Jan 27, 2013
I have 3 WAP321, all set to uk time zone, all the settings restor apart from the time on reboot that defaults back to 1999 despite NTP server listed, interestingly have to manually reset time to present before NTP will update it
View 1 Replies
View Related
Dec 16, 2012
it is normal for the WISM2 time to be resetted to default of 1 Jan 2000 after rebooting the 6506E if no NTP is configured?I had to configure it back to the correct time. If not, the APs will not come up.Also, does the ap or wlc keep track of the ap group the ap is provisioned to?
View 3 Replies
View Related
Jan 22, 2013
my cable company tells me my router is not refreshing ?? even after i disconnect - reconnect ..the power is the button on top with the circling arrows for refreshing it .. i do have a static IP if that makes a difference .
View 8 Replies
View Related
Dec 23, 2011
I have a WBR-1310 D-link and was in setup this morning trying to fix my password cause the old one stopped working. Somehow I changed the password and no longer have access to the settings to change it to one that I can use to log on with my other wireless devices!!! Is there a way I can reset the whole thing? I mean something that makes sense to someone who is new to wireless internetting?
View 1 Replies
View Related
May 12, 2011
So, after everyone was raving about the 1.35NA version, I downloaded it. As I always do, I disabled my wireless NIC and connected an RJ-45. I saved my config to a .gws file. I uploaded the new firmware. When I went to reload my settings file, it said it was not a valid file. I tried multiple times. I even tried earlier versions of saved config files. Same thing.
So, I figured I'd revert to the 1.34NA firmware it was previously on. It wouldn't take it. So, I used the router config "system" page and chose "restore factory defaults". It didn't work. It still had the 1.35NA. So, I used the router's reset button. I held it in for 10 seconds, saw the system lights all blink in unison. I checked the config page and it was still on 1.35NA.
View 2 Replies
View Related
Jun 24, 2012
I initially set it up for static IP, which was a mistake for reasons I probably don't need to go into here. Having recognized my mistake, I've been trying to hard reset it so I can convince it to acquire its IP address by DHCP, but each time I reset it and return to the "First, select your camera" screen in the setup wizard, I'm faced with a single choice: the device as I first set it up for static IP. I don't seem to be able to convince it to give up that erroneous static IP address.I have read the FAQ section on hard reset. I've held down the reset button for a lot longer than 6 seconds while the cam was connected to power and ethernet, and I've watched it go through the sequence of flashing blue reset and WPS lights until it settles down, but this doesn't change the situation, evidently.
View 7 Replies
View Related
May 30, 2012
I am having a recurring problem with tcp sessions timing out / getting reset. I'm using the DIR-655 with PPPoE on a Qwest DSL line. Everything appears to be working fine (including my ipv6 tunnel) except for this issue where my long running ssh & database connections are being reset after a period of time.Currently have 2.03NA loaded, tried using 2.07NA but couldn't get ipv6 working correctly with the newer version.
View 7 Replies
View Related
Feb 23, 2011
I need to reset my 615 remotely. I will have someone on the other end push the reset button. I will then need to have them login to the 615 wirelessly. I'll establish a remote control session to their computer, and then I'll reconfigure the router settings. I know how to reconfigure the router just fine.
1) How long do you press the reset button, the manual says 10 seconds, is that correct?
>> 12 SECONDS
2) Once reset, is wireless turned on by default? I hope so, but the manual shows ENABLE WIRELESS unchecked... is that the default setting? Do I HAVE TO CONNECT VIA LAN CABLE TO "ENABLE WIRELESS" first?
>> YES
3) is the default ssid = "dlink" (no quotes)
>> YES
4) is the SSID invisible by default, or is it visible immediately after RESET?
>> IT IS VISIBLE AFTER RESET
The person on the other side can't access the router with a LAN cable, so once reset, the only way to get into the router will be via wireless; that's why I want to be sure I can do this before we do the reset.
View 5 Replies
View Related
Jul 21, 2010
my router internal time somehow will not working on manual config it will stop after certain period now im trying to use NTP
[code]....
View 2 Replies
View Related
Jan 25, 2013
how to reset password for wireless d-link router
View 2 Replies
View Related
Jan 9, 2013
I have been using d link routers for a very long time. However, recently I have a problem with one of my dlink router..
Basically I have a Wireless N 150 Home Router (DIR-600 B2). I managed to reset and login to the router at http://192.168.0.1. I tried to made some configuration (disabling DHCP, some stuff, basically I was trying to configure this router as Wireless Repeater to connect to another room downstairs).
So it didn't connect so I do a reset (hold a pen for 20+ seconds at the reset button) and now I cant login to the router at http://192.168.0.1..
View 4 Replies
View Related
Feb 24, 2011
Does a RESET automatically re-enable wireless = ON? or is wireless OFF until you go into the config and reenable it?
View 2 Replies
View Related
Nov 3, 2012
I have just bought a DIR-825 rev C1 stock firmware 3.0 (19 Jan 2012,) and I am pleased with its performance so far. However, I need to allow DHCP renewal request to pass through from all IP to UDP port 67 to UDP port 68; or else I will have to reboot DIR-825 every 24 hours (which is not fun ). My U-verse 2wire modem is a 3600HGV.
View 4 Replies
View Related
Apr 14, 2011
Shareport recognizes the printer only after resetting the DIR-825 router. I don't know if this is a Shareport issue or an issue with the DIR-825 disabling the USB port.This happens after there is no PC connected to the router for a number of hours such as overnight. I have 1 laptop and 1 desktop running Win 7 64-bit and 1 laptop running Win 7 32-bit. The desktop is connected directly to the router and the laptops connect via wifi. All PCs work perfectly when the DIR-825 is reset.This isn't a big issue but it's extremely annoying and shouldn't happen. I use a Cisco WAG320 in my office that has similar USB functionality and this never happens.
D-Link Router: DIR-825
FW Version: 1.13NA
Operating System: Win 7 32 and 64 bit
SharePort Version: 3.1.0 R1 (SXUPTP Driver : 3.4.6.0)
View 2 Replies
View Related
Jan 18, 2012
I have a DIR-655 (HW rev A2) that has worked mostly fine for a long time. Today I decided to do a firmware upgrade, and in preparation I backed up my custom config settings and did a hard reset via the factory reset button on the back of the unit.
Since then, the unit itself has been inaccessible from my computer. If I connect the DIR-655 and a PC with a network cable, the appropriate light goes on on the front of the router, but the client does not lease an IP address from the router and I can't access the router home page at 192.168.0.1.
I have tried the reset button again and also power-cycled multiple times, and I have tried connecting from multiple computers, all with the same unsuccessful results. how to "un-brick" the device?
View 6 Replies
View Related
May 31, 2011
Is there a way to reset the camera remotely, via the browser interface or a FTP connection? I can't find a "reset camera" button on the web interface...unless I've overlooked it.
View 3 Replies
View Related
Jan 30, 2011
I just changed my internet provider from DSL to cable. When I hooked up the DIR-615 I had some difficulties. At first my computers would all connect to the router but there was no internet connection. I had to download the latest firmware and install it. After the install succeeded, everything seemed to be okay. However, I now occasionally get the message that the connection to the server was reset while the page was loading. Also, the little world symbol on the router constantly flashes at a rapid rate. Before the switch, neither of these two things happened. When I check the download speed it seems fine. The cable modem is an Arris and also handles my telephone service.
View 10 Replies
View Related
Jul 31, 2012
DIR-615 REv E, Originally had a Windows vista, windows 7, sony bravia tv (hardwired), sony blue ray player, 2 blackberry torch, an ipod, and whoever else happened to be there connected. After a router push button reset 7 reconfigure, only the windows vista and a samsung tablet will connect. The windows 7 computer sees the router but cannot see the internet. It does connect if hardwired thru the router.
View 1 Replies
View Related
Jan 4, 2013
I had DAP-1522 setup for more than two years and working fine. I changed the default IP address from 192.168.0.50 to 10.0.0.50. Recently I replaced my older router with a new one, and now I want to reconfigure the DAP-1522 with the new router, but unable to login. I tried to factory reset but it doesn't seem to work. When I hold the reset button for 10-20 secs, I see the blue power light blinking, but it continues to blink forever. I left it for 4-5 hours and no difference yet. how to successfully reset to factory defaults so that I can access it using 192.168.0.50 IP address?
View 1 Replies
View Related
Feb 1, 2010
I have installed DD-WRT firmware onto my new D-Link DIR-615. It causes some problems and I'd like to re-flash router with orginal firmware. After turning router on with Emergency Room mode and choosing right (as for me) image file I'm getting "Unable to upload the image, please make sure the uploaded file is the correct image." Information.
Firmware downloaded from: [URL]
How can I fix my router? Which firmware file will be correct if not an original?
View 9 Replies
View Related
Dec 23, 2010
Hooked up this router the other day to replace my old Linksys G - which has been bulletproof for 8 years. I am now wondering if I made a mistake with this unit.
I set up DDNS - after much trial and error with dyndns it now works fine.I tried to set up NTP time function - does not work. Then I set time manually. Of course on reboot it looses the time since there is no internal time function. So I need NTP.In the course of troubleshooting I turned off DDNS and behold the NTP time function now works. I turn DDNS back on and NTP does not work.
I see no logical connection between these two functions, yet the seem to interact (or not) somehow.When the NTP is not working, on reboot the time displayed in the router is the last time that I MANUALLY set the time, even though that is grayed out since I have (supposedly) activated NTP.
If I do NOTHING to NTP and uncheck DDNS, after reboot the time is correct.I tried many different NTP servers all with the same result.Looking back on-line, I see the NTP function has been a continual problem with some folks (maybe those using DDNS?) in earlier firmware. Come on DLINK don't you think it's time to get this fixed?
View 6 Replies
View Related
Jun 12, 2011
Set my DIR-655 to limit my son's time on the Internet. I have all the connections set to the MAC Addresses
View 4 Replies
View Related
Jan 19, 2011
Internet cable to dir655 and cat5 to master computer with slave using wireless. Network between them always works fine. But if master connects to internet the slave will lose the internet until the master disconnects. like it won't share the signal.
View 1 Replies
View Related
Nov 24, 2012
I starting having really bad lag when playing games or just surfing. I put on wireshark and can see my router is broadcasting all the time. here is part of the wireshark log
"1","0.000000000","D-Link_**:**:**","Broadcast","ARP","60","Who has 192.168.0.172? Tell 192.168.0.1"
"2","0.000737000","D-Link_**:**:**","Broadcast","ARP","60","Who has 192.168.0.171? Tell 192.168.0.1"
"3","0.001469000","D-Link_**:**:**","Broadcast","ARP","60","Who has 192.168.0.170? Tell 192.168.0.1"
"4","1.002284000","D-Link_**:**:**","Broadcast","ARP","60","Who has 192.168.0.169? Tell 192.168.0.1"
it does this for the whole subnet then starts over. i turned off all the broadcasting in all the menu and it still doing it. i upgraded to 2.10NA, but it did not seem to do anything to it. I bought this router on 3-5-11. I have not tried resetting it to factory settings. I wanted to see if i missed something first. Router is on a APC UPS with the modem and the switch.
Hardware version is dir-655 B1
firmware is 2.10NA
cox cable is my ISP
View 14 Replies
View Related
Nov 1, 2011
When I first got my DIR-655 (Hardware version B1) the Wireless would keep on turning itself off, and it needed a reboot of the unit to turn it back on again.After having upgraded to the 2.03NA version of the Firmware it seems to be working correctly and hasn't turned off for a few days now.
View 14 Replies
View Related
Oct 21, 2011
I have one Cable Modem/Router built in (Netgear CGD24N) and I wish to use two routers (the other being the DIR-655). The Netgear is a fantastic Cable Modem but a ****py router, but I wish to use both. One will be situated upstairs and the other downstairs.I have connected the two at different locations via the wall and the DIR-655 successfully went to the Netgear login page (as I went to 192.168.0.1) but internet connection was not working, whereas the Netgear internet was working. This was connected LAN to LAN.
Another procedure I have tried was connecting to them LAN - INTERNET (INTERNET being the D-link one) and received the following message: "The addressing of the Internet side learnt thru DHCP conflicts with the addressing selected for the LAN side. Internet communications will be disabled until you have changed the LAN side addressing to resolve the problem."
View 1 Replies
View Related
Aug 13, 2011
My kid is heading off to college with a Toshiba Satellite E-205 laptop and a Kodak ESP Office 2150 printer. She would like to use the wireless printer option on the Kodak, which requires a wireless router. I have a D-Link DIR-655 wireless router that I can send with her.
I know her university has a very robust wireless system for Internet access, so she is going to want to use their wireless access.
So, the DIR-655 sole use will be to allow access to the printer. It will not be accessing the Internet or be cabled into the university's network.
Is it possible to operate TWO wireless connections at the same time so she can hit her university wireless and the DIR-655 so she can print wirelessly?
how do I configure the laptop and the DIR-655 to allow this kind of access?
View 2 Replies
View Related
