I have just bought a DIR-825 rev C1 stock firmware 3.0 (19 Jan 2012,) and I am pleased with its performance so far. However, I need to allow DHCP renewal request to pass through from all IP to UDP port 67 to UDP port 68; or else I will have to reboot DIR-825 every 24 hours (which is not fun ). My U-verse 2wire modem is a 3600HGV.
View 4 RepliesI have DIR-615, connected via ethernet. I enabled port forwarding for Quake 3, using the range of 27660-27980 to account for custom server ports. Set schedule to "always" although also did "never" but it didn't make a difference. I checked the FAQs for frequent resets vis a vis application outbound requests, which recommended disable uPnP and this had no effect. Symptom: when Quake 3 attempts to connect to the Master Server, the router resets all connections, LAN and WLAN. It takes approximately 30 seconds to regain connection to WAN, although LAN does not drop. Also during this time, the world sigil on the router itself turns orange. This is the only time this happens, when trying to play Quake 3. Previous router to this one was Linksys (by Cisco) BEFSR41, in which simply setting up port forwarding for the client IP address allowed connection. I can find no particular reason why the router resets all interfaces when blocking a port, if it is indeed the firewall triggering this.
Other infos:
Model: Wireless N 615, DHCP enabled on both sides
LAN connect: Category5 to 10/100 NIC onboard to Intel 865GBF
Client firewall: none
Client OS: Windows XP Professional SP3
I have one server 172.16.0.100 and i nat this server to a public ip X.X.X.5 and i open RDP for this public ip.Now when i access Remote desktop on this public ip x.x.x.5 it open perfectly.Now my senario is that i want to open a http url on port 5555,server ADMIN open port 80 for this URL on LOCAL lan(http://172.16.0.100:80)So how can i map port 5555 to port 80 on ASA 5520.so when i hit URL [URL]
View 5 Replies View Relatedi can't do it with ASDM and try to use command but still fail
nat (inside,outside) source static inside-10.18.20.162 4F-1.1.1.2
it is working fine for the above command if there is more than one public ip, in case 1.1.1.1 is for firewall interface public ip?if i have only one public ip and i would like to forward http traffic to my internal network? how can i use command to do that?
ASA5505 port 3306.I have been fighting for days to open the port 3306 on my appliance, I have read carefully all the forums and no success.
View 9 Replies View RelatedI installed the thomson router, the process was sucessfully completed however the laptop could not automatically renew the IP address and the DNS server address???
View 2 Replies View Relatedi have CSC-SSM-20 i want to renew the license to support 750 users for 3 years if i have base license only and if i have base and plus as bundle?i want to know the steps and also the part numbers and what is the difference between these two part numbers
ASA-CSC20-750UP-1YASA 5500 CSC-SSM-20 750-User w/ Plus Lic. Renewal (1-year)
ASA-CSC20-750P-1YASA 5500 CSC-SSM-20 750-User Plus Lic. Only Renewal (1-yr)
I bought a Dlink DIR-815 the firmware version is 1.0 and not see any info in D-linlk support site inclusive the original firmware is not there. So I request to create a new forum topic for this hardware, I am replacing a DGL-4500 with this brand new model and we need other users have a good place to share info.
View 14 Replies View RelatedIs renewal charges of hardware firewall is high?I want to buy the hardware firewall for my office were about 20 comp are there and i heard that its renewal is very high is it true. i can spend rs 40-.50 k for firewall but it tough for me to pay renewal of 20 k every year, is this much high renewal i have to pay/
View 1 Replies View RelatedI realize that this is a new product, but nevertheless I have some feedback after running my 4 new DCS-930L camera over the past few days.
Currently, you can configure the camera to EMAIL/FTP images on a schedule or when motion is detected, but not both.
Why does it matter? Because I get flooded with email alerts after I get home from work and later in the evening every time I walk by one of the cameras or whenever a light switch is turned on/off.
If I could configured the motion detection to only alert during a specified schedule of days and hours, it would be great!
We are deploying a new batch of RV016 with the latest firmware (4.0.4.02). We are using 3 WAN ports for internet access (WAN1, WAN2, WAN3)The WAN ports connects to Cicso 800 series adsl modem with DHCP.The RV016 WAN1 port setting regularly resets to 0.0.0.0 despite that the modem dhcp is still up and running. A cold boot, resets all the configuration and WAN1 port start working againg a new ip.
All three WAN ports are set to automatically obtain ip from the modems.We have tried several modems, and even swap WAN ports, but the error is persistant to WAN1 only.
WAN2 and WAN3 are up and running without any errors. This error is persistant with WAN1 only.We have also configured a manual ip on WAN1, and after a few hours of operation on all 3 ports, traffic on WAN1 comes to a halt.We have the same error on 3 units we received last week.All there modem are configure on different subnets.It does not seems to be a configuration error with the modem as they work perfectly well with the WAN2, WAN3 ports.We also tested a RV016 out of the box using the wizard setup, without any extra setting/configuration, and we got the same error after a few hours of operation.
how can I reset the port statitics on the RV180 router without rebooting the router? I have the latest firmware.
View 5 Replies View RelatedIs it possible to reset this switch oif yo uare unable to get into the console or web interfaces?
View 2 Replies View Relatedmy cable company tells me my router is not refreshing ?? even after i disconnect - reconnect ..the power is the button on top with the circling arrows for refreshing it .. i do have a static IP if that makes a difference .
View 8 Replies View Related I have DIR-655, 1.33NA. Recently, I noticed the clock in the router was off, so I wanted to correct it. Each and every time I go through the steps to reset the clock, using time server or clone computer time, or manual reset, after the save settings and reboot of the router, i find the router still displays the wrong time, and frequently reverts itself to a time on Feb 22, 2012. Same problem for trying to reset the DST settings, turning automatic time from server on and off, changing the time server polled. Additionally, I have forced the router to factory settings and rebuilt all of my configuration no less than 4 times.
So, since I recently had to trade out the cable modem because Cablevision fried it with their 'system upgrade', I'm also wondering if the same shenanigans also damaged the router.
I have a WBR-1310 D-link and was in setup this morning trying to fix my password cause the old one stopped working. Somehow I changed the password and no longer have access to the settings to change it to one that I can use to log on with my other wireless devices!!! Is there a way I can reset the whole thing? I mean something that makes sense to someone who is new to wireless internetting?
View 1 Replies View RelatedSo, after everyone was raving about the 1.35NA version, I downloaded it. As I always do, I disabled my wireless NIC and connected an RJ-45. I saved my config to a .gws file. I uploaded the new firmware. When I went to reload my settings file, it said it was not a valid file. I tried multiple times. I even tried earlier versions of saved config files. Same thing.
So, I figured I'd revert to the 1.34NA firmware it was previously on. It wouldn't take it. So, I used the router config "system" page and chose "restore factory defaults". It didn't work. It still had the 1.35NA. So, I used the router's reset button. I held it in for 10 seconds, saw the system lights all blink in unison. I checked the config page and it was still on 1.35NA.
I initially set it up for static IP, which was a mistake for reasons I probably don't need to go into here. Having recognized my mistake, I've been trying to hard reset it so I can convince it to acquire its IP address by DHCP, but each time I reset it and return to the "First, select your camera" screen in the setup wizard, I'm faced with a single choice: the device as I first set it up for static IP. I don't seem to be able to convince it to give up that erroneous static IP address.I have read the FAQ section on hard reset. I've held down the reset button for a lot longer than 6 seconds while the cam was connected to power and ethernet, and I've watched it go through the sequence of flashing blue reset and WPS lights until it settles down, but this doesn't change the situation, evidently.
View 7 Replies View RelatedI am having a recurring problem with tcp sessions timing out / getting reset. I'm using the DIR-655 with PPPoE on a Qwest DSL line. Everything appears to be working fine (including my ipv6 tunnel) except for this issue where my long running ssh & database connections are being reset after a period of time.Currently have 2.03NA loaded, tried using 2.07NA but couldn't get ipv6 working correctly with the newer version.
View 7 Replies View RelatedI need to reset my 615 remotely. I will have someone on the other end push the reset button. I will then need to have them login to the 615 wirelessly. I'll establish a remote control session to their computer, and then I'll reconfigure the router settings. I know how to reconfigure the router just fine.
1) How long do you press the reset button, the manual says 10 seconds, is that correct?
>> 12 SECONDS
2) Once reset, is wireless turned on by default? I hope so, but the manual shows ENABLE WIRELESS unchecked... is that the default setting? Do I HAVE TO CONNECT VIA LAN CABLE TO "ENABLE WIRELESS" first?
>> YES
3) is the default ssid = "dlink" (no quotes)
>> YES
4) is the SSID invisible by default, or is it visible immediately after RESET?
>> IT IS VISIBLE AFTER RESET
The person on the other side can't access the router with a LAN cable, so once reset, the only way to get into the router will be via wireless; that's why I want to be sure I can do this before we do the reset.
how to reset password for wireless d-link router
View 2 Replies View RelatedI have been using d link routers for a very long time. However, recently I have a problem with one of my dlink router..
Basically I have a Wireless N 150 Home Router (DIR-600 B2). I managed to reset and login to the router at http://192.168.0.1. I tried to made some configuration (disabling DHCP, some stuff, basically I was trying to configure this router as Wireless Repeater to connect to another room downstairs).
So it didn't connect so I do a reset (hold a pen for 20+ seconds at the reset button) and now I cant login to the router at http://192.168.0.1..
Does a RESET automatically re-enable wireless = ON? or is wireless OFF until you go into the config and reenable it?
View 2 Replies View RelatedShareport recognizes the printer only after resetting the DIR-825 router. I don't know if this is a Shareport issue or an issue with the DIR-825 disabling the USB port.This happens after there is no PC connected to the router for a number of hours such as overnight. I have 1 laptop and 1 desktop running Win 7 64-bit and 1 laptop running Win 7 32-bit. The desktop is connected directly to the router and the laptops connect via wifi. All PCs work perfectly when the DIR-825 is reset.This isn't a big issue but it's extremely annoying and shouldn't happen. I use a Cisco WAG320 in my office that has similar USB functionality and this never happens.
D-Link Router: DIR-825
FW Version: 1.13NA
Operating System: Win 7 32 and 64 bit
SharePort Version: 3.1.0 R1 (SXUPTP Driver : 3.4.6.0)
I have a DIR-655 (HW rev A2) that has worked mostly fine for a long time. Today I decided to do a firmware upgrade, and in preparation I backed up my custom config settings and did a hard reset via the factory reset button on the back of the unit.
Since then, the unit itself has been inaccessible from my computer. If I connect the DIR-655 and a PC with a network cable, the appropriate light goes on on the front of the router, but the client does not lease an IP address from the router and I can't access the router home page at 192.168.0.1.
I have tried the reset button again and also power-cycled multiple times, and I have tried connecting from multiple computers, all with the same unsuccessful results. how to "un-brick" the device?
Is there a way to reset the camera remotely, via the browser interface or a FTP connection? I can't find a "reset camera" button on the web interface...unless I've overlooked it.
View 3 Replies View RelatedI just changed my internet provider from DSL to cable. When I hooked up the DIR-615 I had some difficulties. At first my computers would all connect to the router but there was no internet connection. I had to download the latest firmware and install it. After the install succeeded, everything seemed to be okay. However, I now occasionally get the message that the connection to the server was reset while the page was loading. Also, the little world symbol on the router constantly flashes at a rapid rate. Before the switch, neither of these two things happened. When I check the download speed it seems fine. The cable modem is an Arris and also handles my telephone service.
View 10 Replies View RelatedDIR-615 REv E, Originally had a Windows vista, windows 7, sony bravia tv (hardwired), sony blue ray player, 2 blackberry torch, an ipod, and whoever else happened to be there connected. After a router push button reset 7 reconfigure, only the windows vista and a samsung tablet will connect. The windows 7 computer sees the router but cannot see the internet. It does connect if hardwired thru the router.
View 1 Replies View RelatedI had DAP-1522 setup for more than two years and working fine. I changed the default IP address from 192.168.0.50 to 10.0.0.50. Recently I replaced my older router with a new one, and now I want to reconfigure the DAP-1522 with the new router, but unable to login. I tried to factory reset but it doesn't seem to work. When I hold the reset button for 10-20 secs, I see the blue power light blinking, but it continues to blink forever. I left it for 4-5 hours and no difference yet. how to successfully reset to factory defaults so that I can access it using 192.168.0.50 IP address?
View 1 Replies View Related I have installed DD-WRT firmware onto my new D-Link DIR-615. It causes some problems and I'd like to re-flash router with orginal firmware. After turning router on with Emergency Room mode and choosing right (as for me) image file I'm getting "Unable to upload the image, please make sure the uploaded file is the correct image." Information.
Firmware downloaded from: [URL]
How can I fix my router? Which firmware file will be correct if not an original?
I need the router's name and can't find it. I've tried every combination I can think of and still no luck. I thought it it might be the SSID but no.
View 1 Replies View RelatedMy computer is an XPS 360 with alot of upgrades. After looking at the specs of D-links routers I thought I give it a try. Hooked up, works like a dream. Couple months later my computer was saying I have "limited connectivity." All of the other computers have full access and works great. I tried going to my routers home page, but all I get is "The server at 192.168.0.1 is taking too long to respond." Ive tried renewing the ipconfig, restarting everything, new cables....everything I can imagine. I tried calling my ISP and they told me it wasnt there fault, that its pretty much on my end. I called Dell for support, said my warranty went out and they cant do a thing.
View 14 Replies View RelatedRegion : Others
Model : TL-MR3420
Hardware Version : V2
Firmware Version : openwrt-mr3420-v2-HM2013-04-19
ISP : Cellcom Israel
how to make hard reset to MR3420.I installed openwrt-mr3420-v2-HM2013-04-19 software to my router.and after that while the router restart the led green lights flashing on and of all the time.and I cant contact to the router with wifi or lan cable