D-Link DIR-615 :: Wireless Setup After Reset?
Feb 23, 2011
I need to reset my 615 remotely. I will have someone on the other end push the reset button. I will then need to have them login to the 615 wirelessly. I'll establish a remote control session to their computer, and then I'll reconfigure the router settings. I know how to reconfigure the router just fine.
1) How long do you press the reset button, the manual says 10 seconds, is that correct?
>> 12 SECONDS
2) Once reset, is wireless turned on by default? I hope so, but the manual shows ENABLE WIRELESS unchecked... is that the default setting? Do I HAVE TO CONNECT VIA LAN CABLE TO "ENABLE WIRELESS" first?
>> YES
3) is the default ssid = "dlink" (no quotes)
>> YES
4) is the SSID invisible by default, or is it visible immediately after RESET?
>> IT IS VISIBLE AFTER RESET
The person on the other side can't access the router with a LAN cable, so once reset, the only way to get into the router will be via wireless; that's why I want to be sure I can do this before we do the reset.
View 5 Replies
ADVERTISEMENT
Nov 1, 2012
My router wasn't giving out proper ip addresses so I went through the steps to reset the router to factory defaults. After I tried to run the setup off of the cd which came with the router and the program is saying it can't find my router
View 9 Replies
View Related
Mar 29, 2012
I've just managed to reset the WRT 300N to default settings and have setup the internet connection etc and home network ... BUT no matter how I've fiddled with the wireless settings I cannot get any of the laptops or mobile phones to connect wireless to the network.The Windows software on the laptops 'finds' the router OK but for some reason the router seems unwilling to supply an IP address.I've checked ALL of the settings that I can think of, and all are correct ... well, all are exactly the same as my old router which worked perfectly.
View 4 Replies
View Related
Feb 24, 2012
How to set upo configuration & Security after reset
View 2 Replies
View Related
Jan 25, 2013
how to reset password for wireless d-link router
View 2 Replies
View Related
Feb 24, 2011
Does a RESET automatically re-enable wireless = ON? or is wireless OFF until you go into the config and reenable it?
View 2 Replies
View Related
Jan 14, 2012
I need the router's name and can't find it. I've tried every combination I can think of and still no luck. I thought it it might be the SSID but no.
View 1 Replies
View Related
Feb 8, 2013
Region : UnitedStates
Model : TL-WDR3600
Hardware Version : V1
Firmware Version :
ISP :
I recently bought wdr3600 and just trying to configure bridge through WDS configuration. I just enabled WDS and picked my initial wireless router after clicking the Survey button, then save it. After the reboot, I cant seem to ping/access 192.168.0.1 and the wireless SSID cant be seen any longer. I tried doing the reset button for 30secs but looks like nothing is working and not resetting. And I am still getting 169.254.x.x
View 5 Replies
View Related
Jan 22, 2013
my cable company tells me my router is not refreshing ?? even after i disconnect - reconnect ..the power is the button on top with the circling arrows for refreshing it .. i do have a static IP if that makes a difference .
View 8 Replies
View Related
Mar 4, 2012
I have DIR-655, 1.33NA. Recently, I noticed the clock in the router was off, so I wanted to correct it. Each and every time I go through the steps to reset the clock, using time server or clone computer time, or manual reset, after the save settings and reboot of the router, i find the router still displays the wrong time, and frequently reverts itself to a time on Feb 22, 2012. Same problem for trying to reset the DST settings, turning automatic time from server on and off, changing the time server polled. Additionally, I have forced the router to factory settings and rebuilt all of my configuration no less than 4 times.
So, since I recently had to trade out the cable modem because Cablevision fried it with their 'system upgrade', I'm also wondering if the same shenanigans also damaged the router.
View 4 Replies
View Related
Dec 23, 2011
I have a WBR-1310 D-link and was in setup this morning trying to fix my password cause the old one stopped working. Somehow I changed the password and no longer have access to the settings to change it to one that I can use to log on with my other wireless devices!!! Is there a way I can reset the whole thing? I mean something that makes sense to someone who is new to wireless internetting?
View 1 Replies
View Related
May 12, 2011
So, after everyone was raving about the 1.35NA version, I downloaded it. As I always do, I disabled my wireless NIC and connected an RJ-45. I saved my config to a .gws file. I uploaded the new firmware. When I went to reload my settings file, it said it was not a valid file. I tried multiple times. I even tried earlier versions of saved config files. Same thing.
So, I figured I'd revert to the 1.34NA firmware it was previously on. It wouldn't take it. So, I used the router config "system" page and chose "restore factory defaults". It didn't work. It still had the 1.35NA. So, I used the router's reset button. I held it in for 10 seconds, saw the system lights all blink in unison. I checked the config page and it was still on 1.35NA.
View 2 Replies
View Related
Jun 24, 2012
I initially set it up for static IP, which was a mistake for reasons I probably don't need to go into here. Having recognized my mistake, I've been trying to hard reset it so I can convince it to acquire its IP address by DHCP, but each time I reset it and return to the "First, select your camera" screen in the setup wizard, I'm faced with a single choice: the device as I first set it up for static IP. I don't seem to be able to convince it to give up that erroneous static IP address.I have read the FAQ section on hard reset. I've held down the reset button for a lot longer than 6 seconds while the cam was connected to power and ethernet, and I've watched it go through the sequence of flashing blue reset and WPS lights until it settles down, but this doesn't change the situation, evidently.
View 7 Replies
View Related
May 30, 2012
I am having a recurring problem with tcp sessions timing out / getting reset. I'm using the DIR-655 with PPPoE on a Qwest DSL line. Everything appears to be working fine (including my ipv6 tunnel) except for this issue where my long running ssh & database connections are being reset after a period of time.Currently have 2.03NA loaded, tried using 2.07NA but couldn't get ipv6 working correctly with the newer version.
View 7 Replies
View Related
May 12, 2011
I had to get a new router from verizon cause the old one died. so i reset the camera and wipe all the dlink software and settings. I then start fresh. i get all the way to choosing wireless and input the password. It states that there is a problem saving your settings. I tells me nothing more. I spent 4 hours on the phone with tech support and i can get it working through wired but I can't put it in my childs room wired. it worked perfectly before the router switch. funny thing is that its the same brand and model router.
View 4 Replies
View Related
Jan 9, 2013
I have been using d link routers for a very long time. However, recently I have a problem with one of my dlink router..
Basically I have a Wireless N 150 Home Router (DIR-600 B2). I managed to reset and login to the router at http://192.168.0.1. I tried to made some configuration (disabling DHCP, some stuff, basically I was trying to configure this router as Wireless Repeater to connect to another room downstairs).
So it didn't connect so I do a reset (hold a pen for 20+ seconds at the reset button) and now I cant login to the router at http://192.168.0.1..
View 4 Replies
View Related
Nov 3, 2012
I have just bought a DIR-825 rev C1 stock firmware 3.0 (19 Jan 2012,) and I am pleased with its performance so far. However, I need to allow DHCP renewal request to pass through from all IP to UDP port 67 to UDP port 68; or else I will have to reboot DIR-825 every 24 hours (which is not fun ). My U-verse 2wire modem is a 3600HGV.
View 4 Replies
View Related
Apr 14, 2011
Shareport recognizes the printer only after resetting the DIR-825 router. I don't know if this is a Shareport issue or an issue with the DIR-825 disabling the USB port.This happens after there is no PC connected to the router for a number of hours such as overnight. I have 1 laptop and 1 desktop running Win 7 64-bit and 1 laptop running Win 7 32-bit. The desktop is connected directly to the router and the laptops connect via wifi. All PCs work perfectly when the DIR-825 is reset.This isn't a big issue but it's extremely annoying and shouldn't happen. I use a Cisco WAG320 in my office that has similar USB functionality and this never happens.
D-Link Router: DIR-825
FW Version: 1.13NA
Operating System: Win 7 32 and 64 bit
SharePort Version: 3.1.0 R1 (SXUPTP Driver : 3.4.6.0)
View 2 Replies
View Related
Jan 18, 2012
I have a DIR-655 (HW rev A2) that has worked mostly fine for a long time. Today I decided to do a firmware upgrade, and in preparation I backed up my custom config settings and did a hard reset via the factory reset button on the back of the unit.
Since then, the unit itself has been inaccessible from my computer. If I connect the DIR-655 and a PC with a network cable, the appropriate light goes on on the front of the router, but the client does not lease an IP address from the router and I can't access the router home page at 192.168.0.1.
I have tried the reset button again and also power-cycled multiple times, and I have tried connecting from multiple computers, all with the same unsuccessful results. how to "un-brick" the device?
View 6 Replies
View Related
May 31, 2011
Is there a way to reset the camera remotely, via the browser interface or a FTP connection? I can't find a "reset camera" button on the web interface...unless I've overlooked it.
View 3 Replies
View Related
Jan 30, 2011
I just changed my internet provider from DSL to cable. When I hooked up the DIR-615 I had some difficulties. At first my computers would all connect to the router but there was no internet connection. I had to download the latest firmware and install it. After the install succeeded, everything seemed to be okay. However, I now occasionally get the message that the connection to the server was reset while the page was loading. Also, the little world symbol on the router constantly flashes at a rapid rate. Before the switch, neither of these two things happened. When I check the download speed it seems fine. The cable modem is an Arris and also handles my telephone service.
View 10 Replies
View Related
Jul 31, 2012
DIR-615 REv E, Originally had a Windows vista, windows 7, sony bravia tv (hardwired), sony blue ray player, 2 blackberry torch, an ipod, and whoever else happened to be there connected. After a router push button reset 7 reconfigure, only the windows vista and a samsung tablet will connect. The windows 7 computer sees the router but cannot see the internet. It does connect if hardwired thru the router.
View 1 Replies
View Related
Jan 4, 2013
I had DAP-1522 setup for more than two years and working fine. I changed the default IP address from 192.168.0.50 to 10.0.0.50. Recently I replaced my older router with a new one, and now I want to reconfigure the DAP-1522 with the new router, but unable to login. I tried to factory reset but it doesn't seem to work. When I hold the reset button for 10-20 secs, I see the blue power light blinking, but it continues to blink forever. I left it for 4-5 hours and no difference yet. how to successfully reset to factory defaults so that I can access it using 192.168.0.50 IP address?
View 1 Replies
View Related
Feb 1, 2010
I have installed DD-WRT firmware onto my new D-Link DIR-615. It causes some problems and I'd like to re-flash router with orginal firmware. After turning router on with Emergency Room mode and choosing right (as for me) image file I'm getting "Unable to upload the image, please make sure the uploaded file is the correct image." Information.
Firmware downloaded from: [URL]
How can I fix my router? Which firmware file will be correct if not an original?
View 9 Replies
View Related
Aug 6, 2011
Presently I'm using the Wireless 150 DIR 600 router to share a internet connection between my desktop (with LAN cable from LAN port in Desktop PC connected to LAN port in router) and Laptop connecting wireless to router. Now I also want to create a LAN connection between my Desktop (LAN cable connected to router) and Laptop (wireless) using the same router. Is it possible ? If yes, how can do it ?
View 5 Replies
View Related
Jul 22, 2010
My computer is an XPS 360 with alot of upgrades. After looking at the specs of D-links routers I thought I give it a try. Hooked up, works like a dream. Couple months later my computer was saying I have "limited connectivity." All of the other computers have full access and works great. I tried going to my routers home page, but all I get is "The server at 192.168.0.1 is taking too long to respond." Ive tried renewing the ipconfig, restarting everything, new cables....everything I can imagine. I tried calling my ISP and they told me it wasnt there fault, that its pretty much on my end. I called Dell for support, said my warranty went out and they cant do a thing.
View 14 Replies
View Related
Apr 28, 2013
Region : Others
Model : TL-MR3420
Hardware Version : V2
Firmware Version : openwrt-mr3420-v2-HM2013-04-19
ISP : Cellcom Israel
how to make hard reset to MR3420.I installed openwrt-mr3420-v2-HM2013-04-19 software to my router.and after that while the router restart the led green lights flashing on and of all the time.and I cant contact to the router with wifi or lan cable
View 5 Replies
View Related
Oct 28, 2011
Basically, my issue stems from the latest Boxee firmware from 2 weeks ago, that since then, its been causing my DIR 655 to reset itself, thereby disabling my whole home internet. It eventually turns back on again after a while, but the process doesn't stop.Basically, my DIR 655 is connected, hard wired to my boxee. I also have a NAS 323 hard wired to my router. I've had this setup on my boxee, reading all my movies/shows from my NAS without any issues for the past 10 months. Then the firmware from 2 weeks ago on the boxee started to cause my router to reset. I thought it was a hardware router failure, so I bought another of the same model to try that out, same thing happened though. When I rolled back my boxee firmware to the previous version, it no longer causes my router to reset.Now, besides me trying to figure out how to correctly block the boxee from updating on the router. Is there anything I can do on the router to tell it to prevent it from letting the boxee forcing it to reset? I'm on High Speed DSL. My internet provider modem is acting as a bridge to my DIR 655. Its been working fine for the past 10 months.
I've also done the following:Ensure DNS IP addresses are being filled in under Setup/Internet/Manual? You can find thse under Status/Device Info/Wan section. Turned off ALL QoS Turned off Advanced DNS Services if you have this option under Setup/Internet/Manual.Turned on DNS Relay under Setup/Networking.Setup DHCP reserved IP addresses for all devices on my router.Ensure devices are set to auto obtain an IP address.I have Set Firewall settings to Endpoint Independent for TCP and UDP..
Basically, I've put my boxee back to my previous firmware, and this doesn't cause my router to reset and disable my internet. But I don't get how/why a firmware update can trigger my router to do this?
View 6 Replies
View Related
May 11, 2010
Ever since setting up this router it has been giving me problems on my laptop, connected wirelessly. At random intervals, throughout the house, an error saying "Connection was reset" comes up in firefox when browsing the web. I've tried resetting the router twice, and updating my network adapter's(Intel 465AGN) drivers. Neither of these worked. No settings on the router were modified, other than enabling the Qos engine. Signal quality isn't the problem either as it is full at all times. On my other computers, three connected through wireless and one through wired, there have been no problems at all and they perform very well.
View 2 Replies
View Related
Jan 8, 2010
I have DIR-615, connected via ethernet. I enabled port forwarding for Quake 3, using the range of 27660-27980 to account for custom server ports. Set schedule to "always" although also did "never" but it didn't make a difference. I checked the FAQs for frequent resets vis a vis application outbound requests, which recommended disable uPnP and this had no effect. Symptom: when Quake 3 attempts to connect to the Master Server, the router resets all connections, LAN and WLAN. It takes approximately 30 seconds to regain connection to WAN, although LAN does not drop. Also during this time, the world sigil on the router itself turns orange. This is the only time this happens, when trying to play Quake 3. Previous router to this one was Linksys (by Cisco) BEFSR41, in which simply setting up port forwarding for the client IP address allowed connection. I can find no particular reason why the router resets all interfaces when blocking a port, if it is indeed the firewall triggering this.
Other infos:
Model: Wireless N 615, DHCP enabled on both sides
LAN connect: Category5 to 10/100 NIC onboard to Intel 865GBF
Client firewall: none
Client OS: Windows XP Professional SP3
View 6 Replies
View Related
Mar 22, 2011
I've just gotten a DIR-615 and replaced a working linksys G router. I configured it to work with my ipad (wireless N), my laptop-win 7 (N), and my desktop-vista (USB connected N). Everything works ok,. I'm using WPA personal, WPA2only, AES encryption, 3600, 802.11n only, auto 20/40 mhz channel width, invisible.
Here's the problem. As I powered up and shut down the laptop each day, it wouldn't connect to the router. I could see the connection, but windows said it couldn't connect. I had to go and unplug the router, count to 10, and then plug it in, and tell the laptop to connect and then it would connect it would be fine.
I thought it might be a compatibility with the laptop driver, but after powering down the desktop today, I had to do the same power cycle on the router to get the desktop to connect. So then I went and turned off the IPAD and had the same thing happen. 3 for 3.
I'm pretty sure its router settings and not the 3 devices, this never happened with the Linksys router, but I don't know what to change.
One other odd thing, when I view the network in windows, the DIR-615 icon is there (for about 15 secs), and then it disappears (for about 5 secs), and then reappears (15 secs), disappears (5 secs), etc. - almost like its dropping out for 5 secs... I haven't noticed a performance hit, but haven't transfer big files yet.
View 14 Replies
View Related
Jan 8, 2012
I had to reset and reboot. I entered the router ISP and went through the 4 step process then rebooted.
My question/problem is now the router is wide open. How do I find page where I can enable the security settings and lock down the router to the outside world?
View 3 Replies
View Related
Feb 7, 2012
I have been having wireless issues for a while now and decided to buy a TP-Link router to work with this, unfortunately the wrong model was sent out, it's for Cable use only as it is just a router not modem too!I attempted to send it back but as I didn't know it was wrong until I opened it they won't take it back now as I should have checked first apparently.I did some research online and found information that I can use it as my wireless transmitter as long as I use my SKY router as the modem (with it's wireless function switched off).I have attempted the set-up as described in the manual for the TP-Link and I am now speaking to you using the Ethernet port on it, yet none of my wireless devices can see it in the available networks, both the "system" and "WLAN" lights are flashing to say the router is working but I still have no wireless signal.
View 10 Replies
View Related
