Linksys Wireless Router :: WRT610N + FTP Server Working?
Sep 14, 2011
I have a router WRT610N and I'm using the FTP option within. The problem is that within my network, I have the cable modem (from the internet provider ) and my router with the ftp server. When I'm trying to access the FTP from outside (internet) with FileZila I get this "Server sent passive reply with unroutable address. Using server address instead."
I 've checked the network config from FileZilla and if I'm using this [URL] in order to get the public IP, I get this : 127.0.0.1
I am trying to filter a URL, facebook and it is not working. I have tried rebooting the router and it is still allowing access. I have provided the settings and ranges for PCs.
Using a wrt610n.I am trying to Isolate one of my wireless bands from the rest of the network. I turn on the AP Isolation and I still have access to all of my wired computers. With AP Isolation working will they be able to see the hard drive plugged into the router?I've heard that they can still see other wireless devices, is that true? And if so, can they see others wireless devices on the other wireless band?
Using a wrt610n. I am trying to Isolate one of my wireless bands from the rest of the network. I turn on the AP Isolation and I still have access to all of my wired computers.
Questions: With AP Isolation working will they be able to see the hard drive plugged into the router? I've heard that they can still see other wireless devices, is that true? And if so, can they see others wireless devices on the other wireless band?
WRT610N router with v2 firmware stopped working correctly. It loses wired connection via LAN ports.My home network has one PC connected to LAN port 1 and two PC connected via Wi-Fi.Recently unexpectedly the PC with wired connection lost connection.
The symptoms are the following: - The DHCP local network address is obtained not every time. - The router (192.168.1.1) not usually responds to ping (returns "host is unreacheable) and I even unable to connect to router's web interface. - The led for the 3rd LAN port on the front face of router is always on while nothing was ever connected to this port. - Wi-Fi clients (Windows XP) obtain DHCP address for 30 seconds then report that connection is limited and in a few seconds report that everything is - The internet for both type of clients is almost not accessible (Wi-Fi is better)
Sometimes (but very rarely the wired connection works fine.
I suppose in my case this is a hardware problem. Can this be repaired of fixed somehow?
I have a WRT610N (v2) router and I recently updated the firmware to the most current version 2.00.01 build 15. I can no longer set WPA2 security for both bands (used to work just fine). Every time I try to save settings for WPA2 for the 5 GHz band, it tells me it was successful but then displays that the security mode is disabled (and it shows up on my computers list as not having any security enabled. If not, where can I get a copy of the old firmware that worked?
FiOS gave me an Actiontec router that every other day is getting into a state where it refuses to give out IP addresses via DHCP. I have to reset the router to get it to work again.This seems ot have started in the last year, I assume due to some piece of equipment I added, or perhaps the VPN software or Windows 7 installed on my work laptop. I've not been able to figure out what is tripping up the Actiontec router, so I decided to try moving the DHCP function over the WRT610N that I have. I basically had the WRT610N setup without DHCP enabled, no NAT and no RIP, so it was basically just working as an access point. I left the Actiontec at 192.168.1.1 and assigned 192.168.1.2 to the WRT610N on the LAN side, while the WAN side is left disconnected.
I disabled DHCP on the Actiontec and enabled it on the WRT610N. I also set the DNS server to 192.168.1.1 so it would go to the Actiontec for name resolution. Using nslookup from a command prompt on a PC wireless connected to the WRT610N, I can see that names are indeed getting resolved. However, it looks like the WRT610N is setting itself up as a the gateway at 192.168.1.2. When trying to ping something out on the net, I get a message back saying that 192.168.1.2 is reporting the address as unreachable.
I assume this is because the WRT610N is handing out its own address (192.168.1.2) as the gateway. Is there anyway to get the WRT610N to hand out a different gateway address than itself? Optionally, is there a way to get the WRT610N to route requests coming to it over the Actiontec?I suppose I could just ditch the Actiontec altogether, but it seems a bit easier to use to setup port forwards and the like for various servers we have running. It also has a coax MoCA interface which I believe our FiOS set-top boxes use for their internet connectivity, so I don't want to lose that.
We have a WRT610N wireless router in our office.we want to setup VPN server through a static ip.we dont know what needs to be done in the router settings to create a VPN server. (necessary port forwarding etc)??
My WRT610N media server is not serving up large, MKV files (>1GB). I have a 500 GB Maxtor connected with external power.The media server serves smaller files just fine (although they are not MKV files). The disk is formatted as NTFS. I can access the large, MKV files via mapping network drive, so I know they are present on the disk and they are intact; but they media server does not show them.
I am trying to stream movies and music to my Panasonic TV. I have a USB hard drive connected to the EA4500.
The TV sees the media on the device and music plays fine. However, every movie I've tried shows up with an exclamation point and when I try to play it I get a message to the effect that "unable to open media". Is the EA4500 media server only compatible with certain movies?
I purchased a WRT610N router early this month, the wireless network was working completely fine when I first set it up. Today I tried to connect my laptop to my wireless network. The laptop isn't able to connect at all. I also got a Sony PSP which has WLAN on and that saying it cannot detect any access point which would be my router.
I was told that this router would push the PoE to the WAP4410N. I hooked the AP up to port 1 and no lights or anything... The network is all cat6, patch cords are cat6 shielded if this matters at all... what am I missing.
I have the Linksys WRT610N wireless router and would like to know if it is possible to block all domains ending in .XXX? The access restrictions let you type in a 'specific' URL, but using a generic domain name doesn't seem to work. I basically want to block all access to any URL that ends in .XXX.
I just bought a certified refurbished router. The model is WRT610N-RM. Where's what I've done:
1. Downloaded newest firmware from the site using old router, Then disconnected. Connected a lan cable to the new router. Powered up the router. Held down reset untill the light blinks. Went to the browser and typed 192.168.1.1. Entered password to go into router and upgraded firmware. 2. 5 Ghz Settings: Went to Wireless menu. Selected "manual", mode is "mixed" (If i chose N only for 5 Ghz, then It won't save my setting for internet security. Instead it will be "disable" no matter what". The rest was default. SSID is enabled. Then I set up the 2.5 Ghz. I have 3 other computers with N wireless card. Some others have G, however when I viewed available networks, I only see the 2.4 Ghz ssid. I tried to reboot and unplug power for 10 seconds, but no luck seeing the 5 Ghz.
ive tried all types of things i read online and it is stuck on moderate no matter what i do, im hooked into router directly, when i hook directly into modem it switches to open.
I am finding it impossible to set up port forwarding. No matter what I do I remain completely stealthed when I do a port probe via [URL]... The only way I seem to be able to open a port is if I enable remote management. When I do that, whatever port I specifiy as the remote management port is then fully open. Obviously, I can't leave a port exposed like this and, anyway, I need to open multiple ports for my purposes.
I have had no problems with my WRt610N fo 2 years. Yesterday a problem occured and today again. Namely, I opened my laptop (the lid) and suddenly it could not see my network (SSID) among the rest of the neighbouring ones. The WiFi indicator in the tray showed the yellow "!". Since I have another (secondary) router wired to the primary (WRT610N) I tried and succeeded to connect to it (same SSID, but type "g").
Today the same situation. This is the straneg thing - if I 1st connect to the "g" router after a while the WIn7 reports my SSID being of type "gn" meaning it now sees the primary WRT610N. If I switch off the secondary the netowork is maintained by the primary router showing "n". It seems like my laptop cannot see my router (but can see all other networks) until it 1sr connects to the secondary, and afterwards it sees the primary router and can stay with it.
I've been really stumped when I decided to start using xbox live. When ever I try to join my friends party I am slammed with a NAT error. For years now I have not been able to forward ports at all. Any port checkers come back with unable to contact your router.I am fairly certain its the router because, I directly plugged my 360 into my modem and everything worked like a charm.I've read on a similar post found here "Similar post" that updating the firmware might fix the issue?
My WRT610n went out today for no apparent reason.All of my other peripherals are still running, but the router won't turn on. I've tried different transformers, outlets and powerstrips, with no luck -- no power. I've also tried a hard reset on it, with no luck.
How is it possible to block facebook (or other sites) on WRT610N router, given that I have already set up Internet Access restrictions based on day/hour ?
Any success with a recent vintage Macbook Pro connecting to the 5.8Ghz channel on a WRT610N. I can connect with the 2.4 channel without a problem but I cannot maintain a connection on the high channel. Linksys support told me that the hardware was not compatible with the high channel.
To connect my new "smart tv" with my wireless linsys WRT610N, smart tv ask to take off all protection such as firewall and antivirus. Doing so, I cannot connect my laptop with my router. Is there a solution to connect both at the same time?
I read an earlier posting about an issue between SPI on the latest WRT610N Version 1.0 firmware and a user's Apple TV. This pointed me to a "solution" to a perplexing problem I was having.
I have 4 machines, 3 connected via WiFi and 1 on one of the wired ethernet ports. I also have 2 Apple Airport Express units for audio streaming as well as 2 iPhones connected wirelessly.
Now for the symptoms, which are all new since updating to firmware ver.1.00.03.15:
1. The WiFi machines see the Airport Express units and can stream audio to them. However, the iPhone Remote app has trouble staying connected to iTunes running on any of these machines. A router reboot is a temporary fix, but connection is eventually lost again.
2. The wired machine cannot see the Airport Express units, nor can the Remote app pair with iTunes on that machine. It's as though no Bonjour-related functions work. Here, a router reboot also provides a temporary fix, but one that lasts only minutes.
Based on that prior post, I disabled SPI on the router and, lo and behold, the wired machine suddenly sees all Airport Express units and can pair with the iPhone Remote app!
I was going crazy, verifying that I was not having Windows Firewall issues, that there wasn't an incompatibility with Windows 7 (which I'm running on all), that this wasn't a Homegroup incompatibility of some sort, that Bonjour was up to date, etc. Only turning off SPI fixed the problem entirely.
So, Linksys ...Any firmware bug fix in the works for this? Can I safely go back to the prior firmware update without security or function concerns? If so, where can I get my hands on the older firmware file?
i used my 610N v2 for 2 years and recently i upgraded my network from 100mb to fiber 500mb , however, if i directly plug the lan cable to my computer , i can get full speed , but with 610N, the speed is limited to 130 for both upload and download .i had already upgrade my firmware and did factory reset, none of them work. Is it the limitation of the router ?
For some reason, I have been trying to use QOS for several network related jobs (VPN, streaming). It would seem that when QOS is enabled and the appropriate ports are set which a high priority, the speed of my connection drops to a crawl. When I disable QOS, I'm flying again. I have confirmed ports, and protocol types (TCP or UDP) and nothing seems to work.
I just purchased a WTR610N and when I connect to the admin interface over SSL it gives me a cert that expired on 12/31/1970. I updated the firmware and that didn't change anything. How to get it to use a valid cert?
I want to connect one "wrt610n router" to modem directly through Ethernet cable and when i connect both of them every thing is working fine and iit gives proper internet connection through WLAN [code] But, when i tried to connect "second WRT610N router" through "first one WRT610N router" through LAN_cable(cat 5) then second router do'nt provide(give) internet connection second router ip-- 192.168.1.5
how to set up my router settings/port forwarding to be able to use Wake on Lan with Depicus here is what I currently have:DHCP Reservation with the IP Address of my computer (192.168.1.xxx) and the MAC address xx:xx:xx:xx that I retrieved by doing ipconfig /all in the cmdMy Router address is 192.168.1.1 and the submnet mask is 255.255.255.0my DDNS service is disabledIn the Security tab, I unchecked Filter anonymous internet requestsIn Applications and Gaming, under single port forwarding, I have port 7 to 7, Both TCP and UDP, forwarded to the IP address of my computer 192.168.1.xxx and it is enabledMy network card is configured already, enabling WOL in the card's properties.Now when I use Depicus, I enter the MAC, my external IP address which I got from myipaddress.com, subnet mask I use 255.255.255.0, I select Internet, and then the remote port I use is 7,Doing that, nothing happens at all. however, I can easily wake up my computer if I am connected to the same local network at home.
I was able to connect using Gnome Epiphay Web Browser v 3.4.1 and found no problems on the WRT610N router.So-o-o Cisco, what do you recommend I do, seeing as how there is no later firmware to apply and nothing to configure that I can see.
I am using Window 7 and the WRT610N router. I got a bufflao 1 TB USB harddisk connected to the router.My PC can access to the Harddisk. However, but my pc showing the USB harddisk is full. I checked, there are less than 200GB file on the disk. why is that?
