Looking for support on setting up an ATM managed switch. It is a little older and void of documentation, model being Marconi ASX-200BX, that I can console but am lost from there. Much different than any Cisco switch I've ever seen.0
View 1 RepliesI just purchased a new SF-300 managed switch for the purpose of using it on the DMZ, so we can mirror the internet port and monitor traffic for my company. I have set it up from the web interface to miror port 1 to port 2 and that's pretty much it. I decided to test it before putting it in production, by hooking it up to one of my core network switches, connecting a laptop to it and trying to get online. It doesn't even connect to my DHCP server to get an IP address. If I put the laptop back on the same subnet as the switch management IP, I can still connect to the switches web interface. Isn't the basic functionality of a switch to pass traffic?
I should also mention that I'm not a network engineer, so there might just be something I'm missing with regard to a default setting that needs to be switched off?
I need a ≥ 8 port layer 3 managed switch. What would be the cheapest solution for this?I've been looking at some stuff like Cisco 4908G, but that only supports 1000base-X. I need something that supports the standard 1000base-T. I've also looked at a Cisco WS-C3508G-XL-EN, but correct me if I'm wrong, this is only layer 2?
View 11 Replies View Relatedi have a 20 story high rise condo bldg that i am providing internet service to. I have a 8 port managed network switch on the 1st floor. I have a cat6 line ran from each port to the 8 distrabution closets in the bldg.My question is this if i am using a managed switch to send the signal to the other switches, do the other switches also need to be managed? or can i use unmanaged switches at the other locations. I do not want each condo on those switches to be able to see or comunicate with the other condos on those switches. I am using 48 port switches in the 8 distrabution closets.
View 5 Replies View RelatedI'm looking to get a layer 3 managed switch. The HP we currently have only does layer 2.I'm looking at a HP v1910-24g. It has 24 10/100/1000 ports and looks to be layer 3 as well.It looks like they can be had for around $350.Anything different I should be looking at with similar specs? Any issues with the v1910-24g?
View 19 Replies View RelatedI have two public IP's entering a location from two different sources. One is under our control and the other is a 3rd party. Lets say Ours: 1.2.3.1 3rd Party 1.2.3.2
One is coming in through a firewall/router and the other is a direct link. Each will come into a different network segment 192.168.200.0/24 and 192.168.210.0/24
some of the hosts one subnet will need to talk to the other.
My envisioned setup would be as follows.
1.2.3.1 will come in to the firewall/router into the managed switch. 1.2.3.2 will come in the the same switch but in a vlan The vlan will have a trunked port to the firewall/router to allow routing between the vlan (192.168.210.0) and the other subnet (192.168.200.0).
I have a SG-300-20 Managed switch. I attached a picture of what I want to do. Is this possible to do? How would I go about doing it?
View 6 Replies View Relatedsuch as the SLM2048T can be configured as an managed switch. Our schools have laptop carts and we want to put switches in the carts so that the laptops will be plugged into the network when not in use and software installs, updates, etc. can be pushed to the laptops while they're in the cart instead of waiting for them to be taken out, powered on and pushed over wireless. I can find a 10/100 48-port unmanaged switch, but I really want a gigabit unmanaged switch, but they don't seem to exist so I was wondering if a managed switch can be configured and used as an unmanaged switch. I don't want to have to assign a static IP address to the switch.
View 1 Replies View RelatedI am a lucky enduser of an 3400 ME switch.i admin an 80 comp LAN with segments splitted by unmanaged layer 2 switches.Now i want ti use a 3400 me switch .I connect an ethernet cable between the console port of switch and lan computer dell server application windows 7 ethernet port.What's next?I browse the cisco site,download configuration assistent but nothing.I installed a hyperterminal and wait for call ,nothing.So,what's next?how can i give an ip to cisco swith?
View 1 Replies View RelatedI have bought this switch to try :
We (our company) have a new glass fiber internet from a provider with 5 ip-addresses in an /29 range. I try the accomplice the following. On port 1 comes the output from the provider. On port 2 till 7 I want to separate the ip addresses so can distribute these addresses to our lan, to a wifi hotspot for external company visitors etc. So on port 2 a ip to the lan, on port 3 a ip to wifi router
Any good 24 port rack mountable Gigabit switch, that is managed. Is a HP ProCurve 1800-24G 24 port gigabit ethe switch J9028B decent ? Will i be happy ? I have currently a Dell 5224, that works, but it's getting old and for the life of me can't find rack ears AT ALL!! and i want it mounted so i can finish my rack installation.
budget is around 250-300$ 24 ports all gigabit and manage able for vlans etc etc.
looking to pick a good managed gigabit switch for my central media server implementation.I will have probably 10-12 tvs connected to this along with other things like ip pbx extensions, music streamers, ip cameras etc.Now I can imagine about 2-3 tvs simultaneously streaming HD quality movies. In that case, I am assuming I will need a minimum 150-200mbps throughput switch. Is my assumption wrong?I have been looking at some switches which seem nice and relatively inexpensive but the throughput is much lower than that.If I wouldnt need that kind of throughput then can you explain me how do I come up with my max limit.I initially thought that since its going to be a gigabit switch it would be able to handle that kind of traffic through all its port at once, but I guess thats not a correct assumption. Throughput is what reall dictates simultaneous maximum? Am I correct?
View 1 Replies View RelatedThis is for a short temporary time until I get cisco 3560s in place. I have a 2921 configured and it is connecting to an HP non managed non VLAN switch and I cant get any traffic to pass from my computer to the router (pings or anything). Here is brief configuration that should be enough. [code]
Here are my vlans 1-default, 2-management, 192-data, 92-voice, i believe its running rapid spanning tree protocol. Do i have to take off encapsulation on my data vlan to get it to work or make the data vlan default vlan for everything. I am lost as to why this is not working.
We have recently purchased SG 300-52Port Cisco Switch to support our Network but they constantly having some bizarre issues or I assume bugs, i.e. we cannot Telnet nor SSH to the switch now, whereas we were able to SSH before, we have set them up for Remote Log Services to get some syslogs and reports but no report have been generated nor logs,
I have done some testing through Wireshark and there are absolutely no reports / logs.We have some real issues with this switch and it’s hard to believe that this is a Cisco Product,
SG 300-52 Port Gigabit Managed Switch
Firmware Version (Active Image ) : 1.1.1.8
Firmware Version (Non-active ) : 1.1.0.73
Boot Version : 1.0.0.4
We have a standalone Cisco SGE 2000.
We lost connectivity to the web user interface - it no longer responds on the configured IP address.From the manual we see that by default the switch get its IP address via DHCP - but we find no record of any ip address assigned to this switch.Is there a IP address that this unit defaults to when DHCP is not available? Also - what is the best way to connect to the console using Windows 7?
We have an SG300 managed switch located in a small business of less than 10 PCs. There has been an ongoing issue with Internet speed. Is there any way that I can monitor the router for traffic so that I can see what might be causing the problem? I would like to focus on the WAN port and Internet activity particularly.
View 1 Replies View RelatedI bought an ESW 540 8-port switch, mainly for the POE capability over all 8 ports, so that we can power some SPA50X phones.The concepts of a "managed" switch are challenging for a newbie.Is there a way to make this device behave like a boring "unmanaged" switch ??We have plenty of bandwidth, and don't need to be troubled by QoS and virtual LAN's, or all the security stuff at this time.Making this device work like an unmanaged switch (aka plug-and-pray).
View 2 Replies View Relatedwe have e requirement for a Nexus 5000 switch to be accessed and managed inband, ie the Management interface can't be connected to the rest of our networks management VLAN because the switch is remote and only connected via fibre. We have enabled the interface VLAN feature and configured an interface VLAN but can't seem to PING the IP address configured on it ?
View 10 Replies View Relatedis it possible to cascade a managed cisco switch with an unmanaged switch via SFP LC Modules?
View 1 Replies View RelatedI'm looking to connect my 50+ drops I have in my home based business. I transfer large files 5+gigs on a regular basis between the machines. I currently just have some cheap Netgear 8port, gigabyte switch's but when transferring files I max out around 12-15mb/sec. This takes WAY too long to transfer files.
I need a network switch so I can get my speeds up to 60+mb/sec at least. (my seconds job office has this ability)
What would I need to get this kind of speed? All my cabling is CAT6, with CAT6 ends. Would I need a managed switch to get this kind of speed?
I was looking at a couple switches. Cisco Sg 100-24 24-PORT Gigabit Switch $374 or Cheaper option Netgear Prosafe GS724T-300NAS 24 Port Gigabit Smart Switch W/ Rack Mount Kit $199
Or is there something else I could go with in this price range?
We have modem router 4-port with IP range 10.0.0.1 - 30 setting.one port goes to a library where we have a 8-port switch STLAB SWHUB-8p serving 2 pc with auto IP setting (internet works fine)and one port goes to another corner of the library to a switch TP-LINK TL-SF1008D V4.1 .4 pc are connected and a printer all are set with manual IP in an active rang of the router 10.0.0.10 - 14 they have to be on manual IP becuse of the ptinter.they cannot connect to the internet but I get the message connected.If I change them to auto IP - they can connect to the internet, the router gives them an IP.
View 3 Replies View RelatedIf i want to setup a router and switch in my small business... 11 computers. Can i run 2 switches into one router or is it better to run one larger switch into one router. Second is when I set it up do I need to assign addresses to each computer or do I just need to plug them in and setup the network with windows network wizard. I will have a shared drive on one of the computers or possably some network storage.
View 1 Replies View RelatedI'm asked to think of a solution to make in an existing LAN connected by switches (connected to each other) to make another network availible.atm we have a network with 192.168.110.0 and we are short on IP adresses because of a large DHCP pool from wireless clients and a growing network with static IP addresses.So basicly what i want to accomplish is an extra network 192.168.111.0 in the existing LAN and all computers have to be able to communicate to each other and all computers have to be able to connect to the internet using gateway 192.168.110.1 (direct or trough route tables). For future growth an extra LAN 192.168.112.0 with not perse internet access for only VOIP, but that is on the side and is not a priority, because I can set up that network on the same switches easy without having them to be able to connect to the computers and servers in the network. (correct me if I am wrong)
What I found out browsing the internet is that a layer 3 switch may provide the solution, but I can't make out of the technical specs if thats going to work when both LAN's computers will be connected on the same switches.Also I found a lot of solutions with setting up a server with 2 NIC's and setting up routes on that server. But since we have a very large amount of network traffic with large graphical files, having 2 nics to route all that trafic doesn't seem like a desirable solution for my purpose.
I have to admit I've never written my own Cisco configuration and I probably know just enough to break things. The last time I configured a Cisco was a few years ago, and the Wachovia people just told me what to type.
I have a Cisco WS-C3548-XL-EN and a Cisco WS-C3524-PWR-XL-EN "Inline Power" with default configurations and I want to setup VLANs. Basically, would this work?
SWITCH 1:Router on port 39, Wifi on Port 47, Uplink to 2nd switch's port 24 on port 48
Code:
en
conf t
interface VLAN10
no ip directed-broadcast
no ip route-cache
[code]....
And then I would test that it works, if it does issue #write memory, and it it doesn't powercycle and try again?
this company uses Vyatta firewalls, which are dedicated boxes. So I was sent home with a Dell PowerConnect 5448 (a 48 port switch) with the project of getting a similar setup going with the computers i have at home. I have the switch set up, everything's on VLAN1, management IP is 192.168.2. 255.255.255.0, Default Gateway is 192.18.2.254, and the switch is properly sharing the my internet connection between three computers. That part was easy. So now, one of them is going to be either reformatted and set up with Vyatta, or I'm going to virtualize it. Either way, I need to route all the traffic through that firewall box before it goes to anything else on the switch so I can have a functional firewall.
View 9 Replies View Related1. set up password on a new cisco 3750 switch
2. steps to recover a lost password.
I am trying to set up a VLAN on my Netgear switch (GS105E). I want to create two separate networks and I want both of them have internet access.
I have configured port 1 and port 5 as vlan1 and port 2 to port 4 as vlan2. I plugged a cable from the router to port 5, and the computer on port 1 has internet access. However, the computers on port 2 to port 4 have no internet access.I had tried to create VLANs with the router but had no luck.
I am migrating an a group of workstations that run a fire system from one software to another. The current workstations run the following info:123.123.123.xxx 255.255.255.0The new workstations run:100.100.100.xxx 255.255.255.0There is a central switch location using a GE-DSG-244 Layer 2+ Managed switch. There are two remote location using GE-DS-82 Managed Switches.The two networks must remain isolated, yet use the same fiber communications. The central switch connects to the two location using MM Fiber. From my research I believe I need to use the 802.1q standard to allow port trunking between the two switches.
View 7 Replies View RelatedWe have a Cisco slm248gt-na smart switch in our office that I am trying to configure to support and optimize for VoIP. We have desktops hooked up off the phones in most cases. Are there any config guidelines to optimize the switch so it has proper QOS set and VoIP gets higher priority over data.
View 4 Replies View RelatedThe question is: Will a 3750 switch route Jumbo frame sizes (e.g. 9000 MTU)?
We know that we can change the System MTU to 9000, and someone on a previous thread said that we can change the Routing MTU to 9000 as well, although I couldn't figure out how to do that. However, regardless of how we configure the System MTU and Routing MTU, I don't think we're able to adjust the MTU on L3 VLAN interfaces, so if we want to actually "route" between VLANs on the switch, we're limited to 1500 MTU.
Our situation is that we have a customer connecting to our 3750 switch, and this customer wants to use Jumbo frames. The customer connects to our 3750 switch via their own VLAN, with their own L3 VLAN interface configured on the switch. The customer will point their traffic towards the L3 VLAN interface, then we want to route them onto another VLAN, via a different L3 VLAN interface, before forwarding their traffic. Because of the limitations noted above, specificially regarding the routing between these VLANs via L3 interfaces, I do not think we'll be able to support 9000 MTU frames on this 3750 switch. I think the L3 VLAN interfaces will limit us to 1500 MTU, regardless of what we configured via the global System MTU and Routing MTU settings.
Am new to Nexus switching, i have a Nexus box that i need to link with IBM servers with 10GB Network Cards.
how to set up fiber channel on this machine
I am setting up a new 2960-S switch and none of the recommended username and passwords combinations work. I have tried CIsco Cisco, <blank> cisco and various other permutations.
I have tried to reset the switch to factory defaults and it still doesn't work. The switch is currently connected to a 3560G and has been assigned an IP. If I try to access it from Network assistant it shows as unmanaged and I get prompted for a username and password.The switch is connected to another new 2960-S via a FlowStack module.
I'm trying to set up a 2951 with a 24 port switch module. I want the ports to act similiarly to the ports on an 881 router - where I assign the VLANs on the router and I set the VLANs to the switchport interfaces.I would like to be able to create the VLANs on the router portion of the 2951 and then, enter the switch module and configure the Ports to the VLANs but, how do I logically connect router to the switch? Is it an internal logical interface - meaning how are the VLANs getting from the router to the switch?
View 24 Replies View Related