I am using LINKSYS by CISCO (WRT54G2) Access point wirh out any controller or wireless control system (WCS). Is it possible to connect this AP in mesh scenario, if its possible, how about configuring in mesh mode.
View 2 RepliesI need to connect 4-6 laptops in a mesh network topology. What equipment do I need (switches, hubs cable etc..) and how should I create the connection?
View 1 Replies View RelatedMy harddrive failed. I got a new one and need to connect to my home network, but don't remember the user name or password for the router. I no longer have the setup cd. How do I reset the router and set up the entire home network again without the cd?
View 2 Replies View RelatedDone a wifi mesh using 1552E and 1552i mix of AP's ? With the 1552E as RAP and 1552I's as MAP's ? Is it a recommended model of deployment and will it work well ? the 1552i having radiation pattern more towards the ground when mounted on top , will the mesh backhaul to the 1552E be strong enough ?
Will this work if i put the 1552e at a lower level than the 1552i so that the mesh is formed properly ?
I would like to create a Mesh network using Cisco 1242 AP's running in Autonomous mode via A Channel.
View 5 Replies View Relatedthis note is from the 5508 controller config manual, does this apply to 1040 access points in a mesh network?
Note:The recommended power source for MAPs is either a power supply or power injector. PoE is not a recommended power source for MAPs.
I have a running Mesh Network with AP 1552E and Controller 5508. The end customer has a new requirement to have a indoor coverage near to AP1552E (mesh AP). But in this building he has not any wired Network (it is far from any switched site). The question is: We can use an AP1262 indoor with Line Of Sigth to AP1552E in the running Mesh Network? I know AP1262 can be used in a Mesh Netwok (Root or Mesh) configuring it as BRIDGE [URL]
View 1 Replies View RelatedBy default, 802/11a/n is set for backhaul communication.Does that mean that if most of my clients are on 5ghz, Mesh network is not a preferred design to go? Reason being:- client communication on a/n radio might disturb the traffic of the whole cell and of all the MAPs that connect to the network through that MAP.
View 6 Replies View RelatedWe need to add additional APs to working wireless mesh network (WLC 4402, 1520 series AP).
WLC 4402 supports 1550 series access points with firmware upgrade to 7.0.235.0 :
[URL]
Is AIR-CAP1552E-x-K9 with three external dual band antennas enough for 2-GHz b/g/n local access and 5-Ghz back haul?
Does 1552 Mesh AP work with 1522 Root AP?
I've a WLC 2106 and it is running IOS version 7.0.240. I am trying to setup a wireless mesh and used the Ethernet bridge port on the MAP to extend the network. The wireless mesh works fine but I can not get the switch to work that is connected to the ethernet port on the MAP.I'm using two different Access points. I'm using a Air Cap 3502i as the RAP and a Air Lap1142N as the MAP.The switch port that is connected to the RAP and MAP is configured as the following:
switchport mode trunk
switchport trunk native vlan 2
switchport trunk allowed vlan 10,20,30,40
[code]....
The wireless mesh between the RAP and MAP works fine. I can connect a device to the MAP wirelessly and access the network with no problem but I can not get anything to work that connects to the switch that is connected to the MAP ethernet port.
I have Cisco WiSM running on 7.0.116.0 and 1522 Outdoor AP. I a trying to configure Mesh and I followed the Cisco deployment guide.I had added the MAC address of my AP in the Mac-filter list Configured the Root AP and Mesh AP.Configured the Mesh Parameter.Currently my issue is after removing the client from Ethernet its no more seen in the controller. There is also no information in the neighbour output.
View 2 Replies View RelatedI have seven autonomous AP1242AG (c1240-k9w7-tar.124-25d). Can I configure them to a mesh without WLC? [code]
View 2 Replies View RelatedWe have a Cisco 1522AG configured as a MAP in our production network. Last week the AP went down. On investigating it keeps rebooting itself. constantly showing 4 orange leds, Maybe cant find the WLC? Is there a way to console into these devices to see whats happening in the background while its booting up or even reset it back to the factory defaults?
View 4 Replies View RelatedI have setup'd two 1142 AP's as mesh.The sceneario is like this:
MAP ------ RAP---------SW----------Router
I've done all the configuration through my WLC (Flex7500) and the mesh neighborship is up.The problem is not the MAP nor the RAP broadcasts my SSID.I've joined them to the same SSID and nothing.
A customer have a bad coverage in a corner of his branch office. He like to add a mesh AP (MAP) in the near of that corner.
I checked allready the documention about Mesh but i'm not sure if Flexconnect and Mesh works togheter. This MAP is in a branch office and the WLC is in the head quarter therefore he likes to uses Flexconnect togheter with Mesh.
I'm looking for documentation on the Enterprise mesh solution based on 7.0 MR1...In this release e.g 802.11n APs are supported and clean air for the client radio etc...The current Cisco Mesh Access Points, Design and Deployment Guide is based on the previous 7.0 release.Apart from the configuration guide I can't find any additional guides.
View 1 Replies View RelatedI'm trying to become famillar with Cisco Mesh AP's deployment. As I know RAP's (Roof-top AP's are AP's with Ethernet/Fiber connection to the network). I connected these AP's via L2 switch , they can reach WLC and everything looks fine.
No I want to connect few MAP's to my RAP's. But of course firstly we will need to set-up IP addresses for these MAP's? But how? There is no "configure terminal" option at all ( on mesh AP console) .
MeshAP#?
Exec commands:
access-profile Apply user-profile to interface
[Code].....
I have a Mesh architecture with 2112 WLC and 1042 APs I want just to know if I can connect one 1310 AP to the ethernet port of a mesh 1042 AP with ethernet bridging enabled.
View 4 Replies View RelatedI have one controller 5508 that will hold 50 LAP 1262 and another Controller that will hold another 50 outdoor mesh access point 1552. Both controllers (not redundant) are at the HQ while the access points are distributed between HQ and 3 branches.
The requirements is to have the SAME 4 SSIDs on MESH and LAP each have a security type (, wep,wpa,dot1x...) on HQ and Branches. Now, in the HQ I don't think I will face a problem since the WLCs is on the same LAN, so 5 interface v lans will be configured one for the WLCs and access point and another 4 interface v lans for the 4 SSIDs.
Now, for the remote sites I need to create another vlan on the switch with DHCP and option 43 ..... for the access point to register with the controller.
But here, do I have to create another 4 interface v lans (4 different sub nets) that should be bidden to the SSID as in the HQ?
Or the Access point will encapsulate all the traffic including the client traffic? Note that I have outdoor mesh access point and Lightweight access point and the BW link between the HQ and branch is 100M.
Also Can I have roaming between the same SSID that broadcasted on MESH and LAP knowing that each have different controller.
if the Cisco 3502p AP can run as a root mesh access point ?
View 4 Replies View RelatedI have two Wireless LAN Controllers 2504 and 8 APs 3502e. The WLCs are running software version 7.0.116.0. The problem is that I don't have the mesh option to configure indoor mesh inside the controller. In chapter 9 of Wireless LAN Controller Configuration Guide, Release 7.0.116.0 says that I have to go to Wireless Menu and select the AP. When I am inside the AP general page, the guide says I have to go to the Mesh tab, but that tab doesn't appear in the controller GUI. Do I have to use another image in the controller? Or do you have to use an special mesh code or something like that? Because in the download page of the controller it only appears the 7.0.116.0, two more new versions but there is nothing about mesh image.
View 5 Replies View RelatedI have a Cisco 4402 WLC running version 4.2.112.0 controlling 20+ AIR-LAP1242AG-E-K9 access points running IOS 12.4 (10b). I'm trying to setup an additional AP as MESH. When I try to change the mode from local to bridge, on what will be the rootAP, I get a message stating that bridging is not support on this unit.
View 4 Replies View RelatedI have two WLC5508 controllers running 7.0.230.0, which having the two of them probably is inconsequential because all the APs are added to only one controller. The problem I'm facing is that I have several LAP1552E's deployed throughout my facility, and I have several that are doing Ethernet bridging to some Cisco switches using G0. In this, I have a PC at the end of one of these switches, and using Iperf and PingPlotter to get some metrics, and what I'm seeing is >400ms latency with <3 Mbit throughput to the PC. On the 802.11a radios I have 18 Mbit set as mandatory, with everything below disabled and everything above Supported, with all MCS indexes under 802.11n enabled.
My channel is set to 161 with a 40 MHz channel-width, and a power of 3 configured.After many days of trying different power settings, channel settings, and such, I can't get better results than above and my channel utilization stays > 75% at all times. I do have video cameras attached to the other bridges switches, and have video QoS set to Bronze and the cameras configured to ~ 1 Mbit bandwidth maximum. Also, average RAP-MAP distance is ~ 1100 ft and average MAP-MAP distance is 400 ft, with the longest RAP-MAP being 1400 ft and MAP-MAP distance being 875 ft.
We have a deployment with six 1524SB mesh APs. Two are used as RAPs and face east and west respectively with directional antennas and two MAPs on each side with omni antennas. The RAPs are within 20 feet of each other. I set the bridge group name as east or west depending on which side of the mesh the equipment is located but noticed the downlink channel is set to 56 on both RAPs. I don't remember setting the channel for the RAPs, but they aren't using the global DCA.Would best practice be to change the downlink to unique channels on the RAPs, enable DCA (if it will let me), or is a unique bridge group name sufficient enough?
View 2 Replies View RelatedI am working on a project that will involve 5500 controllers managing 1260 series N rate A/Ps. There may be a requirement for MESH but my previous experience using Motorola 802.11a radios is that random, intermittent radio detections resulted in the MESH network having to keep re-forming resulting in less than 100% availability.
What's peoples experience in the UK is 802.11a outdoors?
Ideally i would prefer to use 2.4GHz and repeater access points for those areas not serviced with data connection but I cant find any info' so far on how whether the 5500 controller is able to manage repeater access points.
I am implementating wlc 2504 and 1520 ap,i installated wlc and ap are got registered. In WLC i changed parameter as RAP and MAP.
As per doucment i have to enable Zero touch configuration in bridging. But bridging option is not their in wlc, wlc is running on 7.0.220
We have a few 1500 outdoor mesh ap's. 1262N are used to link to these 1500 and extend the coverage to places. All 1262 was configured as mesh. But upon installation, none of them actually register to the controller and join the other mesh ap's. They should be joining to the 1500's.
On testing, the 1500 joins the 1262N as mesh. however the 1262N does not join the 1500 as mesh even though the distance is less than 20m.
In our mesh network. there are 8 root AP and 15 mesh AP . we are using 1552E ,i have few questions on it:
1. If the ap's acting as mesh ap are connected with only 2.4 ghz external antenna, will they have problem joining the root access point to form mesh.
2. How should we set the channel assignments. Do we only set them in root ap's.
3. should the channels be set under 802.11a ?
4.should the channel be manually set or should it be left to be chosen dynamically.
Our costumers has implemented 2 AIR-WLC4402-50-K9 with Software Release 7.0.98.0, the wireless infrastructure consist in 2 Root-Mesh-LAP and 8 Mesh connect over-the-air to deploy outdoor coverage.
All the LAP are Aironet 1520 Series Mesh Access Points with equipped with 3 antennas for 2.4GHz and 1 antenna for 5GHz (backhaul).For one year all seems to be ok, yesterday after a power outage of one Mesh-Root-LAP, 5 Mesh-Lap continues reload each 10-12 minutes, on the WLC Log you can see event like a reboot from AP Console, on the LAP console i can capture this event before the reload:
Log on LAP Mesh
%DOT11-6-GEN_ERROR: Error on Dot11Radio0 - Not Beaconing for too long - Current 0 Last 0
%SYS-5-RELOAD: Reload requested by Dot11 driver. Reload Reason:
Radio Not Beaconing for too long ....
LWAPP-5-CHANGED: CAPWAP changed state to DOWN
AP1780-Mesh uptime is 11 hours, 10 minutes
System returned to ROM by power spike
%DOT11-6-GEN_ERROR: Error on Dot11Radio0 - Not Beaconing for too long - Current 0 Last 0%SYS-5-RELOAD: Reload requested by Dot11 driver. Reload Reason:Radio Not Beaconing for too long ....*Sep 1 16:05:43.399: %LWAPP-5-CHANGED: CAPWAP changed state to DOWN
What does it mean? That the beacon signal trasmitted from Root-Mesh-LAP cannot reach the Mesh-Lap and so the Mesh-LAP force a reload?Where we should search the cause? In the power instability or in a interference on the 5GHz radio interface?
On one of mesh Lap I found a strange reason for a releoad:AP1780-Mesh uptime is 11 hours, 10 minutesSystem returned to ROM by power spike
Log on WLC
Log System Time Trap
0 Thu Sep 1 17:31:11 2011 AP Disassociated. Base Radio MAC:00:22:be:41:33:00
1 Thu Sep 1 17:31:11 2011 AP's Interface:1(802.11a) Operation State Down: Base Radio MAC:00:22:be:41:33:00 Cause=Heartbeat Timeout Status:NA
2 Thu Sep 1 17:31:11 2011 AP's Interface:0(802.11b) Operation State Down: Base Radio MAC:00:22:be:41:33:00 Cause=Heartbeat Timeout Status:NA
[Code]....
I want to start implementing a small outdoor mesh network of 3 APs Aironet 1550 in order to grow afterward with more APs. Is there any way to configure those 3 APs in an outdoor mesh configuration (for example, only one RAP and two MAPs) without a Wireless LAN Controller or I have to have at least, one WLC? My idea is to have a WLC 5508, but at the very beginning I don't know if my budget is gonna allow me to cost the WLC.
View 7 Replies View RelatedIs Cisco WCS mandatory when deploying an outdoor enterprise mesh solution?If I am goin to use the 1552E purely as an outdoor access point ,do I really need the Cisco WCS?
View 2 Replies View RelatedI'm using a wlan controller with 1242ag converted to lwapp, i'm trying to enable 5.8 but when i change the from local to bridge the lwapp disappear from controller. May be that the firmware does not support mesh !I'm following the 4402 wlan manual at page 641.
View 5 Replies View RelatedI have to install a wireless mesh network shortly using Cisco 1552 APs. This will be controller based using 5508 controllers. The controllers currently have some 1262 APs configured in a mesh and bridging configuration so happy that it all basically works. My question is - what is the "config mesh range' command doing on the controller ( or setting the Range(RootAP to MeshAP) setting on the controller mesh GUI. The default setting is 12000feet and I have left it at default at present. Just interested in what this is used for - I assume it alters the mesh protocol parameters somehow ( or the RF parameters perhaps ) as it suggests in the guide that mesh APs will reboot following this command being changed.
View 4 Replies View Related