Cisco Wireless :: Mesh LAP Strange Reload In WLC4402

Sep 1, 2011

Our costumers has implemented 2 AIR-WLC4402-50-K9 with Software Release 7.0.98.0, the wireless infrastructure consist in 2 Root-Mesh-LAP and 8 Mesh connect over-the-air to deploy outdoor coverage.

All the LAP are Aironet 1520 Series Mesh Access Points with equipped with 3 antennas for 2.4GHz and 1 antenna for 5GHz (backhaul).For one year all seems to be ok, yesterday after a power outage of one Mesh-Root-LAP, 5 Mesh-Lap continues reload each 10-12 minutes, on the WLC Log you can see event like a reboot from AP Console, on the LAP console i can capture this event before the reload:
 
Log on LAP Mesh
%DOT11-6-GEN_ERROR: Error on Dot11Radio0 - Not Beaconing for too long - Current 0 Last 0
%SYS-5-RELOAD: Reload requested by Dot11 driver. Reload Reason:
Radio Not Beaconing for too long ....
LWAPP-5-CHANGED: CAPWAP changed state to DOWN
AP1780-Mesh uptime is 11 hours, 10 minutes
System returned to ROM by power spike
%DOT11-6-GEN_ERROR: Error on Dot11Radio0 - Not Beaconing for too long - Current 0 Last 0%SYS-5-RELOAD: Reload requested by Dot11 driver. Reload Reason:Radio Not Beaconing for too long ....*Sep  1 16:05:43.399: %LWAPP-5-CHANGED: CAPWAP changed state to DOWN
 
What does it mean? That the beacon signal trasmitted from Root-Mesh-LAP cannot reach the Mesh-Lap and so the Mesh-LAP force a reload?Where we should search the cause? In the power instability or in a interference on the 5GHz radio interface?
 
On one of mesh Lap I found a strange reason for a releoad:AP1780-Mesh uptime is 11 hours, 10 minutesSystem returned to ROM by power spike
 
Log on WLC
Log System Time Trap
0 Thu Sep 1 17:31:11 2011 AP Disassociated. Base Radio MAC:00:22:be:41:33:00
1 Thu Sep 1 17:31:11 2011 AP's Interface:1(802.11a) Operation State Down: Base Radio MAC:00:22:be:41:33:00 Cause=Heartbeat Timeout Status:NA
2 Thu Sep 1 17:31:11 2011 AP's Interface:0(802.11b) Operation State Down: Base Radio MAC:00:22:be:41:33:00 Cause=Heartbeat Timeout Status:NA
[Code]....

View 7 Replies


ADVERTISEMENT

Cisco Wireless :: Configure MESH On WLC4402 With LAP1242?

Mar 12, 2013

I have a Cisco 4402 WLC running version 4.2.112.0 controlling 20+ AIR-LAP1242AG-E-K9 access points running IOS 12.4 (10b). I'm trying to setup an additional AP as MESH. When I try to change the mode from local to bridge, on what will be the rootAP, I get a message stating that bridging is not support on this unit.

View 4 Replies View Related

Cisco Wireless :: Strange Power Failure With AIR-AP1231G

Mar 25, 2012

I'm having the following issue with a couple of 1231's.
 
Some overall config info first:
 
This is a small office with 2x Catalyst 2950 (24-port, no PoE) switches and 4 AP1231G (autonomous). The APs get PoE from a PWRINJ3 each. The injectors are powered by the AP power supplies. Injectors and power supplies are mounted in the patch closet.
 
The 2 switches are connected together over 4 ports (20-23 on each switch), these ports are set to 1Q Trunk mode.
 
The APs are connected to the switches, 2 to each switch, on port 1-2. These ports again are configured as 1Q Trunk.
 
APs are connected to the switch as follows:
 
   [switch] <- patch cable-> [injector] <- patch cable -> [patch panel] <- static cabling -> [outlet] <- patch cable -> [AP]
 
All this has been working without problems for a number of years.
 
A few weeks back, AP2 did not restart after a power cut (everything else did). All LEDs are off, port on switch has no LEDs lit. I did not get around to investigating this furtehr until last week. I unmounted (failed) AP2, took it to the spot where (working) AP3 hangs, and plugged it to the cable of AP3. AP2 came to life immediately. I unplugged it and plugged AP3 back in, which restarted immediately.
 
So I suspect a power supply issue on AP2. I took the injector and power supply that fed AP2 out of the patch closet. When connecting AP2 directly to the power supply, it came to life immediately. So I figure the injector is defective.
 
On the same day, I notice AP4 is also dead (again all LEDs off, no idea how long, could have been that day or could have been a few days - it has definitely been working after the power cut that appeared to have killed AP2).
 
So I order 2 new PWRINJ3s and for good measure 2 new power supplies. Later that day, I took the injector and power supply that fed AP4 out of the patch closet. When I try this combination (AP4, injector4 and P/S4), and connect it to a different wall outlet (and therefore a different port -16 - on the switch) IT WORKS! Should have triggered questions, but did not immediately.
 
Last Thursday I got the new injectors and power supplies. So I take one of each, hook them upto AP2 at my desk, and AP2 starts up. So I mount new injector2 and new P/S2 in the patch closet, put AP2 back in its place, connect all the cables - NOTHING. AP2 does not start. The "power" LED on the injecvtor lights up green, the "device status" LED remains off. I take AP2, new injector2 and new P/S2 to my desk, hook them upto a wall outlet (connected to switch port 17). AP2 starts immediately.
 
Meanwhile AP3 has (also) stopped working (no LEDs on at all). As far as I can tell, it stopped working after I briefly disconnected (and reconnected) the patch cable between injector3 and the patch panel in the patch closet. The LEDs on switch port 1 are off.
 
I have since tried to power cycle both switches (took power off both, waited a while, poewerd both back on). No change.
 
PS: the APs ran firmware 12.3(8)-JA until recently. AP1, AP3 and AP4 were upgraded to 12.3(8)-JEE after the the power cut that took AP2 out. THis is when I found out AP2 was dead. AP2 was still on 12.3(8)-JA. It was upgraded to 12.3(8)-JEE last week when it was on direct power on my desk.

View 3 Replies View Related

Cisco Wireless :: EAP-TTLS Over WLC4402

Apr 18, 2012

I try to use EAP-TTLS on one of my wireless networks and the 802.1x authentification fails at this moment:
 
*Dot1x_NW_MsgTask_0: Apr 19 16:04:52.800: 00:16:cb:66:29:bc Processing Access-Accept for mobile 00:16:cb:06:09:bc
*Dot1x_NW_MsgTask_0: Apr 19 16:04:52.801: %APF-6-RADIUS_OVERRIDE_DISABLED: apf_ms_radius_override.c:204 Radius overrides disabled, ignoring source 2
*Dot1x_NW_MsgTask_0: Apr 19 16:04:52.801: 00:16:cb:66:29:bc Resetting web acl from 255 to 255
*Dot1x_NW_MsgTask_0: Apr 19 16:04:52.802: 00:16:cb:66:29:bc apfMsDeleteByMscb Scheduling mobile for deletion with deleteReason 20, reasonCode 2
 
where I can find what are deleteReason 20 and reasonCode 2?

View 23 Replies View Related

Cisco Wireless :: AP 1602 Strange Hostnames For WiFi Clients

Jan 30, 2013

we want to replace our 1242 AP's with the 1602 model and so far everything works like a charm. We have just noticed, that most of the clients which are connected on the 5GHz N radio, the web interface of the AP1602 shows his own host name instead of the clients host name.
 
For example: 
Radio0-802.11N2.4GHz
SSID INTERN :
[code]..... 
 
The Host name of the 1602 is "AP-LABOR", so why it shows the own host name for the Dell E6420 Notebooks on the 5GHz radio and on some "NONE"?

View 1 Replies View Related

Cisco Wireless :: WRV210 Strange Log And WiFi Drops And Reboot

Apr 13, 2013

I've a WRV210 Wireless-G VPN Router with RangeBooster, that logs this alert almost every time, "Packet type : 0 -- free socket buffer only".Also each time that some devices, like Android, are connected to the Wifi, the wifi starts a reboot and drop cycle.
 
Some extra context information, I've connected to the router a Cisco Gigabit switch and all the wired devices are connected to the switch, that could overload the router? Other point I've a Cisco VOIP gateway connected to the router and a few VPN's and firewall rules setup.

View 1 Replies View Related

Linksys Wireless Router :: DIR-615 Strange Download Speed

Nov 13, 2011

I have searched the forums, and can see that I am not the only one with speed problems on this router. When I changed from a D-link dir-615 (yeah, no wonder I changed it )  my download speed dropped from 4-5 MB/s to 1,3 MB/s. I'm using a wired connection. Have tried disabling QoS in router settings, did a firmware upgrade, reset the router. You see, when I do speed tests on the internet I get 40-50 mbits download, 25-30 mbits upload. I have tried many different files to download, both torrents and through my browser. 

View 2 Replies View Related

Cisco Wireless :: AIR-LAP521G-E-K9 Is Not Joining WLC4402-12

Oct 1, 2012

info regarding my LAP521 access points that are refusing to join the WLC4402-12.This is my first lightweight access point implementation and I have 3 LAP521's and 1 AIR-CAP3502I-E-K9 access points on my network.They are meant to pick up ip address from external dhcp server and then join the WLC but only the 3502i joins successfuly while the 521's get dhcp address but do not join the WLC. From the logs, I can see that the WLC is discovered by the 521's and even get a response message from the controller but they are still unable to join as shown in the screenshot below.My WLC is running software version 7.0.230.0 and the 521's are running an lwapp image version 4.2.61.8. [code]

View 3 Replies View Related

Cisco Wireless :: WLC4402 Drops Network Connection

Dec 6, 2012

We have 2 AIR-WLC4402-K9 devices at a remote location that will both drop their network connections some undetermined time after a reboot.  We cannot reach them via telnet, SSH or HTTP.  In fact, we cannot even ping them once they drop connection.  The only cure we've found so far is to power-cycle the controllers.  The controllers are in separate rooms and connected to separate switches.  We've confirmed the links are configured as trunks and have the correct speed/duplex settings.  I tried updating the IOS & boot loader on one of them but that had no effect on the problem. 

View 19 Replies View Related

Cisco Wireless :: WLC4402 - AP Doesn't Join After Upgrade To 7.0.116.0

Apr 25, 2011

today i upgraded our WLC4402 from 7.0.98.0 to 7.0.116.0. After the upgrade (also bootloader upgrade) the Aironet 1142 AP's do not joint the controller anymore. Error in log:*spamReceiveTask: Apr 26 11:30:46.301: %CAPWAP-3-DISC_INTF_ERR2: capwap_ac_sm.c:1468 Ignoring Primary discovery request received on a wrong VLAN (21) on interface (29) from AP ec:c8:82:ab:ed:00 Nothing changed in infrastructure. AP's are in VLAN 21, AP-Manager interface is in VLAN 21. Ap-Manager, Management Interface and Dynamic Interfaces are in PortChannel (LAG) = Interface 29.

View 8 Replies View Related

Cisco Wireless :: MAC Address Table On Wi-Fi Controller WLC4402

Dec 5, 2011

has WiFi controller WLC4402 mac address table and can I show it somehow?

View 1 Replies View Related

Cisco Wireless :: WLC4402 And 104x H-REAP Mode

Mar 2, 2013

Is there is is any posibility to run WLC4402 and 104x family in H-REAP mode.

View 8 Replies View Related

Cisco Wireless :: WLC4402 - Put Strong Encryption Mode?

Feb 14, 2012

I have one WLC 4402 & arround 29 Access point (1130) in our enterprise network. Wireless users LAN segment is diffrent from wired users.Wireless users like Laptop users, Mobile users & ipad users which are connetced with this wireless & using enterprise network.
 
Presently we are using  WEP mode for security key. This WEP key are week & can be cracked easily. so security point of view i want to put strong encription mode.Presently i do not have any radius server.I found there are some modes are available Like WPA, WPA2 with PSK etc.
 
will there any problem with wireless users to access application after changing the mode? Which mode will be stronger & could not be crack. Could we achieve without radius server or not?

View 24 Replies View Related

Cisco Wireless :: Limited P2P Communication And Broadcast Forwarding On WLC4402

Jun 6, 2012

my question regards to a pair of WLC 4402 with 7.0.98.0 software.Actual, our security policy does not really allow any peer-to-peer communication in a wireless LAN. Therefore we set the 'P2P Blocking Action' to drop, and the 'Broadcast Forwarding' feature to disabled (default).But now there is a special requirement for two mobile endpoints to communicate with each other, because one device controls the other.To test the communication, we first disabled P2P Blocking (without success) and further enabled Broadcast Forwarding to bring the communication up. Now it works, but the configuration disagrees with our policy.
 
1. Is there an alternative configuration as described possible, so that we do not violate the security policy? To allow only p2p connection between the two devices, ist should also be possible to drop any else by an ACL. But how to fix the problem with the broadcast, because of the needed ARP? My idea was to use a static ARP entry, but as far as i know, one of the both devices is not able for it.
 
2. Because, I did not find any detailed documentation:
2a. with enabled Broadcast Forwarding, the controller forwards all broadcast for any configured SSID, right?
2b. is the broadcast limited to the source VLAN/SSID?
2c. is the broadcast limited to an AP, to an WLC, or is it broadcasted to every AP on every WLC that has the relevant SSID?
 
we already have two new 5508 but not in an operational state now, because we plan to implement new 3600 APs.Do these WLCs offer more/another circumstances or possibilities?

View 1 Replies View Related

Cisco :: WLC4402 Can't Connect To Wireless Using Certificate With Android Device

Jan 2, 2013

I'm trying to connect to my wireless network using an android device with certificate but with no success.I'm using a WLC4402 7.0.235.3 SSID Security (WPA2 Auth802.1X + CCKM) [code]

View 7 Replies View Related

Cisco Wireless :: Cannot Connect To Wlc4402 Via Console - Hardware Failure?

Jun 21, 2007

I made a lot of tests during some days with a wlc4402 and everything was ok.
 
One day when I tried to reset the system I had a lot of errors (see attach) and could not go on. After changing the image the following output appeared: "RAM Disk Image Integrity Check Failed (Bad Magic Number) Hanging". Now I have no response from the controller.

View 4 Replies View Related

Cisco Wireless :: AIR-WLC4402-50-K9 - Access Point Not Coming Up After Upgrade Image

Sep 18, 2011

I have AIR-WLC4402-50-K9 WLC i that current IOS is 7.0.98.218 and i upgraded with 7.0.116.0 IOS but after upgrading and reboot the WLC from 15 access point 3 access point are not coming up and 12 are coing up and working fine (4 1142 and 11 1131 series access point) 3 which are not coimg is 1131 series access point. when i login with console to 3 access point its rebooting 2 times and coming on ap: prompt.
 
In between that i reloaded the WLC one more time because from 15 acess point only 4 aceess point are came up and i also cleck the show boot on wlc its output is 7.0.116.0 (default) 7.0.98.218 (active) so i reload  the wlc and checked out of 15 acess point now 12 acess point are up and still 3 are not. And i also checked the output of show boot command its 7.0.116.0 (default)(active) 7.0.98.218
 
So i things its because of when 2nd time i reload the wlc the remaining 3 access point are getting.

View 1 Replies View Related

Cisco Wireless :: AIR-WLC4402-50-K9 - After WLC Reboot Only One Wireless AP Can Join

Mar 1, 2012

I have an issue with my primary WLC AIR-WLC4402-50-K9 running version 7.0.220. After a reboot of the WLC only one AP can join, all others are rejected. After waiting a few hours (about 3) all APs can join the WLC. What I have done is a software upgrade (from 6.0.199.4)  on both primary wlc (wlc with the issue) and backup. Following procedure:

1. Reboot primary wlc so that APs failover to backup (succeeded with no issue).

2. Upgarde software on primary wlc

3. To failback all APs from backup to primary I reboot all APs, so that they join again their primary wlc.

A reboot of the first AP was fine, It joined the primary wlc, get new software downloaded, rebootet, joined wlc successful again. Then rebooting the next AP. But this one then does not join the primary wlc for several hours. But it is also not falling back to the backup wlc as the primary is up and reachable. I tried a reboot with the next AP, but same behavior. I was waiting then until both APs were joining the primary wlc again. This happened after around 3 hours. After that I have rebootet all other APs on the backup wlc also. All was fine they immediately joined the primary without any issue. There are no log messages during the time when the WLC does not allow APs to join.. I had similar behaviour last year with version 6 when I rebooted the device. So I dont think this is software related. Also I dont think it's a configuration issue as 1) I have another WLC that uses the same backup controller and this one has the same configuration but works fine also after a reboot. 2) why doesn't it work after a reboot for a few hours, but then all is fine without any config change. After a few hours all is fine for months (until the next reboot).

View 5 Replies View Related

Cisco Wireless :: WLC4402 / Aironet 1240 AG - Logs Are Rejected Due To Network Policy On NPS Server

May 10, 2012

We are using WLC4402 for our Aironet 1240AG access points.  The clients are connecting to the access points and are authenticating to the RADIUS server.  I am seeing the logs in Server 2008 but they are being rejected due to Network Policy on the NPS server.
 
Where do I see the Authentication Type on the WLC4400 or the 1240's?  In order for the clients (authenticated via Active Directory user) I have to set the Authentication in the NPS Connection Request Policy to "Allow clients to connect without negotiating an authentication method". 
 
I do not have a certificate on the server and my method options are MS-CHAP-v2, MS-CHAP, CHAP, PAP, SPAP, and allow without negotiating.  This RADIUS server was moved from Server 2003 IAS to Server 2008 NPS and there were no issues in Server 2003 IAS.  I have all authentication methods allowed and it still gives me the error below.  Only when I check "Allow clients to connect without negotiating an authentication method" it allows the authentication to proceed. 
 
Client Machine:
    Security ID:   NULL SID    Account Name:  Fully Qualified Account Name:    OS-Version:   
    Called Station Identifier:        00-17-a2-87-54-00: SSID NAME
    Calling Station Identifier:        00-41-96-b6-e3-27
 
NAS:
    NAS IPv4 Address:        192.168.90.24
    NAS IPv6 Address:        -
   [code]...

    Reason:    The user attempted to use an authentication method that is not enabled on the matching network policy.

View 2 Replies View Related

Cisco Wireless :: 5508-HA / SSID Not Broadcasting After Reload

Jan 28, 2013

I have Build a 5508-HA Cluster (7.4.100.0) , hat to reboot this cluster due to Licens install.After the reboot atleast one of the SSIDs was not broadcasting anymore, even the checkbox was checked.
 
What did I do:

Installed the Licenses @ Freiday 12:00
@17:15 reload active WLC, wait till controller is up again (a few minutes pingable)
@17:25 force failover to first controller.
check a few SSIDs but not all, those who where check are ok.
@monday 07:00 clients complaining not seeing the SSID (some where connected)

View 6 Replies View Related

Cisco Wireless :: WLC 7.0 Mesh Configuration

Feb 16, 2013

I have Cisco WiSM running on 7.0.116.0 and 1522 Outdoor AP. I a trying to configure Mesh and I followed the Cisco deployment guide.I had added the MAC address of my AP in the Mac-filter list Configured the Root AP and Mesh AP.Configured the Mesh Parameter.Currently my issue is after removing the client from Ethernet its no more seen in the controller. There is also no information in the neighbour output.

View 2 Replies View Related

Cisco Wireless :: AP1242AG Mesh Without WLC

Jun 2, 2012

I have seven autonomous AP1242AG (c1240-k9w7-tar.124-25d). Can I configure them to a mesh without WLC? [code]

View 2 Replies View Related

Cisco Switches :: Strange Network Standstill SG-300?

Dec 20, 2011

we have a production network that uses five SG300 switches that functions brilliantly most of the time. four of our switches run in layer 2 mode and the last switch runs in layer 3 as it is used to route our 7 vlans as well as routing traffic between our two gateways. the switches use the original firmware that shipped with the devices (v1 device) and will be upgraded within the next week.  the problem that we have is that the network seems to stop routing for all of the hosts after a given time. the only way to fix this issue usually is to reboot the main layer 3 switch. the main layer 3 uses a default route to one of the gateways and a return route has been applied in the gateway. the only thing i can think is that somewhere one of the devices routing tables become full and the network stops responding.

View 2 Replies View Related

Cisco Firewall :: ASA 5520 - Strange Tracebacks

Mar 24, 2011

I have an ASA 5520 with 2GByte RAM running Software Version 8.2(4)4.
 
As soon as I enable outside interface Gi0/0 I get the following error message on the console every now and then:
 
(set_exptime) Timer not a leaf 0x714644dc. Traceback: 0x805e4b3 0x8061b92 0x855ce33 0x85606e7 0x85634ee 0x8563f53 0x8564664 0x8564a12 0x85623a5 0x8063b63
mgd_timer_set_exptime: Not a leaf called from 0x855ce33

I have configured a second 5520 as failover mate and once I have activated the failover device and the configuration replication was finished this second device started the same tracebacks immediately.

View 4 Replies View Related

Strange Connecting / No Cable Detected

Apr 22, 2013

The issue that I am having is that the network cable I have that going from my router to my desktop computer, seems to be flaky, at least it seems that way...When I try to use the network cable that goes into this desktop, into another computer(one that I know works), the connection status alternates between connecting, and no network cable detected, connecting...and no network cable connected, and so forth.it NEVER connects. When I plug the cable back into the desktop, it does the same thing for maybe a minute, but then eventually connects. However, every other computer, laptop, macbook, another desktop PC, that I have tried connecting using this same cable never connects.

View 5 Replies View Related

Strange HTTP Connectivity Hiccups?

Aug 13, 2011

My desktop PC has occasional hiccups in which I can't connect to any website (via any browser, I've tried Firefox, Chrome, Opera & IE) for short periods of time (usually ~1 minute) but all other Internet connectivity seems to be normal. (I can ping Google for instance, and I remain connected to Google Talk, but I can't load the Google website.)

I recently did a fresh install of XP Pro SP3 and am pretty confident that there is no malware running on the system. (I'm running Microsoft Security Essentials and Windows Firewall but I also did a Malware Bytes scan which uncovered nothing.) The desktop is connected wirelessly but I don't suspect an issue with the router because my laptop (via wireless) and my girlfriend's desktop (via wired) can surf the web just fine when my computer is experiencing issues.

I checked for proxies (both in the browser settings and in Windows settings) but everything appears to be setup correctly (that is, unproxied.) DNS is set to the proper DNS servers for my ISP (Cox) but I also tried switching to Google's DNS servers with no luck.

View 3 Replies View Related

Strange Wifi / When Gaming Often Get A Lag Spike Every 10-20 Second?

Feb 23, 2012

My Wi-fi on my rig seems to have some odd problems. When I'm gaming i often get a lag spike every 10-20 second or so, and before I got the "Vista anti-lag" program I was also getting the enormous 60 second lag spike. I'm sure many Vista users recognize this problem. But here is the deal, the first kind of lag spikes completely disappear while talking on Skype! Which makes me wonder, what is it with Skype (only while talking) that removes the lag? Gaming with Skype makes all games run fluently without any spikes at all.

View 2 Replies View Related

Strange Disconnection Only On Online Games

Jul 6, 2012

Basically I started disconnecting when I logged onto Blacklight Retribution after a recent game patch, after a few days the problem stopped and I was able to play again (with no changes to my computer) a few days later another patch was added and the problem occurred again, at first I thought it was a Blacklight specific problem (as this was my only installed game) however i installed a few other games (Kabold Online, Perfect World, Forsaken World, TF2, MW2 and C9) and I got the same problem on each of these games. I haven't been able to log onto a single Online game for more than 5 minutes, normally I'm disconnected at login, HOWEVER, my internet works completely fine in for everything else, i can browse the web, download game clients etc with no problem whatsoever.(Forgot to add, When i disconnect my LAN Cable mysteriously Unpluggs itself (according to computer) and a disable/enable in network manager reconnects it)

- Checked to see if drivers were up to date (they were)
- Rolled back NIC Driver (and put it back when this didn't work)
- Checked device manager for any problems with my NIC, (working as normal apparently)
- Tried setting my NIC to 100mbps Full Duplex
- Setting my power options to not interfere with NIC
- Had a DHCP error in my event logs so i set my gaming machine to a static IP
- Turned of UnUP, Turned on DMZ
- Turned off "Green Ethernet"
- I had other Errors in the form of a service stopping my NIC
- Phoned ISP, Everything is OK there end but they sent out a new router, but problem still occurs
- Noticed that a service was sending a stop control to my NIC, looked on forums for fixes and applied several of them
- Reformatted computer with old XP (switched from windows 7), updated, installed latest drivers etc and still same problem except now I don't get anything in event viewer when the problem occurs.

The only thing i haven't tried is replacing my NIC, but considering the internet works completely fine for everything but Online games I'm unsure how this could be the problem.

View 9 Replies View Related

Cisco Wireless :: Mesh AP1522AG Not Responding?

Sep 17, 2011

We have a Cisco 1522AG configured as a MAP in our production network. Last week the AP went down. On investigating it keeps rebooting itself. constantly showing 4 orange leds, Maybe cant find the WLC? Is there a way to console into these devices to see whats happening in the background while its booting up or even reset it back to the factory defaults?

View 4 Replies View Related

Cisco Wireless :: Flex7500 - Can't See SSID With Mesh APs

Jan 13, 2013

I have setup'd two 1142 AP's as mesh.The sceneario is like this:
 
MAP ------ RAP---------SW----------Router
 
I've done all the configuration through my WLC (Flex7500) and the mesh neighborship is up.The problem is not the MAP nor the RAP broadcasts my SSID.I've joined them to the same SSID and nothing.

View 1 Replies View Related

Cisco Wireless :: Mesh And Flexconnect With WLC5508?

Apr 4, 2013

A customer have a bad coverage in a corner of his branch office. He like to add a mesh AP (MAP) in the near of that corner.
 
I checked allready the documention about Mesh but i'm not sure if Flexconnect and Mesh works togheter. This MAP is in a branch office and the WLC is in the head quarter therefore he likes to uses Flexconnect togheter with Mesh.

View 10 Replies View Related

Cisco Wireless :: Enterprise MESH In Release 7.0 MR1

May 11, 2011

I'm looking for documentation on the Enterprise mesh solution based on 7.0 MR1...In this release e.g 802.11n APs are supported and clean air for the client radio etc...The current Cisco Mesh Access Points, Design and Deployment Guide is based on the previous 7.0 release.Apart from the configuration guide I can't find any additional guides.

View 1 Replies View Related

Cisco Wireless :: AP 1552 In Mesh Mode (MAP)

Sep 14, 2012

I'm trying to become famillar with Cisco Mesh AP's deployment. As I know RAP's (Roof-top AP's are AP's with Ethernet/Fiber connection to the network). I connected these AP's via L2 switch , they can reach WLC and everything looks fine.
 
No I want to connect few MAP's to my RAP's. But of course firstly we will need to set-up IP addresses for these MAP's? But how? There is no "configure terminal" option at all ( on mesh AP console) .
 
MeshAP#?
Exec commands:
access-profile   Apply user-profile to interface

[Code].....

View 21 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved