I have problem in recently installed LMS 4.1 Device discovery will not start when launched manually. When i hit the button, it doesn't even give a popup window saying that the discovery is started and that email will be sent... If I schedule it is launched, runs and finishes correctly. All proceses are started and it seems that application is working ok. LMS is installed on Win 2008 R2.
View 1 RepliesI got a new HP laptop running Windows 7. When I turn on my laptop, my wireless is off. So I click on F12 (my wireless button), to activate my wireless. The orange light turns blue. Even though the light indicates that my wireless is on, I have to go to device manager>networking>802.11n>advanced then activate my radio for my laptop to pick up the wireless signals. The problem is that I have to do this every time I turn on my laptop, and its getting quite repetitive.
View 4 Replies View RelatedWe are using LMS 3.2.1 with SP1 and Campus Manager 5.2.2.Server runs Windows 2003 R2.Everything runs fine except for User Tracking on two Catalyst 6500 switches running CatOS. These devices are discovered, reachable, SNMP works fine, neighbors seen. But when we try to launch acquisition, the UT utility complains with this error message:"Failed to start acquisition: Device unreachable. Please enter a valid device."When we wanted to add ports via Device Trap Configuration, LMS has fired a different error message: "There are no ports to configure for the selected device(s).Check whether you have selected any router(s)." I have checked the portsData.xml file, which doesn't have any ports included for the two devices: [code] We have tried to exclude / include the switches in the data collection, but that didn't work.
View 3 Replies View RelatedI've got the following problem using my DLink DSL-2740B with the latest firmware:On all my devices (Notebook, Netbook, iPhone, Set top Box, TV...) I need to manually set the IP of my internet providers DNS server or else, URL's can't be resolved. I'm pretty sure that the Router/Gateway is set up correctly as the status page of the router does show both the primary and secondary DNS servers IP addresses. Both have been automatically detected by the router.On my different devices, if I leave the DNS IP to be automatically detected, they will use the Routers IP as their DNS server IP (e.g. 192.168.1.1), which is the way it should be I'd think. However, trying to access (in browser or through ping or whatever) any URL, it just won't work. I need to manually enter the DNS's IP in the device.
View 1 Replies View RelatedI am using CISCO PRIME LMS 4.1 for manage my network, i ran a device discovery job using a ping sweep on the ip ranges of my network, ie 192.168.1.0/24, 192.168.2.0/24 and so on... the discovery found all my devices, but it discovered duplicate devices with illegal ip Addresses, i.e.,
ip device
192.168.1.255 S1
192.168.2.0 S1
192.168.2.1 S1 (the real address)
all in reachable status.
I don't understand why the program adds that repeated illegal addresses.. How can I run the device discovery to avoid this problem?
we are running CiscoPrime LMS 4.1 and I have the following problem.I have configured SNMP Settings as shown below (the order of the targets is exactly as it is configured on the server):As can be seen we use three different read community strings. I also have exluded a bunch of IP ranges and IPs from the filter settings. When I manually start discovery everything works fine, meaning that all devices in the above ranges that need to be discovered are discovered as "reachable". The problem appears in the scheduled discovery (happens once daily). In that case only the devices with Read Community snmp1, get discovered as "reachable". All other devices with Read community snmp2 & snmp3, as well as those that are excluded in the filter settings, are discovered as "unreachable".The discovery uses DCR as seed and seed devices are also configured.I also have a problem with PingSweep in the discovery, but I will open another discussion so that I don't complicate this one too much.
View 1 Replies View RelatedI´m getting started on ciscoworks and i trying to configure a device discovery to start but i have some questions about how configure this tool exist 5 parameters that i have to configure to start the device discovery.
•Configuring Discovery Module Settings
#
•Configuring Seed Device Settings
[Code]....
I want to add devices that found neighbors via CDP son in the configuring discovery module setting i choice that option In the configuring seed device setting i choose DCR as seed device that means those devices already in the DCR start discovering from those devices but you can add more seed devices how i can add a seed device ? with ip addres or something like this? and this device have to be in the DCR already or not? The configuring SNMP settings, this community correspond to what device? the devices that i want to add ? and in the field target name what ip adders have to be? and if i have different community of snmp in my devices what device and snmp community have to configure in this parameter
I use the Edit Identity option to change the "Display Name" from an IP to a station name, it is overwritten when a discovery has been done. I have checked the discovery settings and tried using the update DCR Display name setting to prevent this from happening, but it makes no difference.Is there something i am missing? This is on LMS 3.2?
View 2 Replies View Relatedwe use LMS 3.2 in our network. We have a couple of 6509-V-E Switches with mutiple interfaces (VLAN interfaces and Layer 3 interfaces) The problem is, campus manager discovers the switch by a interface randomly...one time its a lay3 Interface and another one its a vlan interface which none of them are in DNS hence no name resolution can be made.
Is there a way to "tell" CM to us for instance the VLAN Management IP of the switch?
I have a very special usecase with migrating devices from LMSv2.6 to v4.1 using DCR bulk import that was maintained manualy, not by discovering.The special thing is each device has its own SNMP-community and its about 1500 devices.RME discovery works fine, but I get the devices not discovered by DCR (CSDiscovery), because I need a minimal DCR discovery configration containing Seed and SNMP-settings. So I activated DCR as seed, but cant skip SNMP settings without an entry. But in this case I would need 1500 SNMP-lines that would be very unhandy. is in CSDiscovery-Settings a possibility to can leave SNMP settings untouched so it takes the credentials from the DCR, to can start DCR discovery?
View 6 Replies View RelatedThe problem is that - although negotiated in global discovery settings - Prime appends domain name to the device name so that all switches (not routers) have "confusing names". The domain name is not required in device name. What can i do?
View 2 Replies View RelatedI just got a new server for hosting, installed Windows Server 2008 R1, and it installed correctly with no errors. First time running it, everything is plugged in, and there ethernet would not pick up at all. Went to Device Manager and got: "This Device Cannot Start. Code 10"Tried different cables, I even swapped the network switches (clearly wasn't the problem). More information can be supplied if needed.
View 3 Replies View RelatedWe are using Catalyst 3750 switch stacks with software 12.2(44)SE. We have two stacks, only one with IP routing enabled.When we try to run an Acquisition Action on this, from Admin> Collection Settings> User Tracking, the system replies with an error "Failed to start acquisition: Device unreachable. Please enter a valid device"device Center reports "success" on all collector status.Acquisition starts successfully when we try with the other stack.With LMS 4.1 demo, users acquisition runs successfully.
View 18 Replies View RelatedI have a Dell Inspiron 1525 that suddenly has an issue with Wireless Networking. When I try and troubleshoot it shows me that the Broadcom 802.11 Multiband Network Adapter has a Code 10 error and says the "device cannot start." I have tried uninstalling and updating the driver, but it just continues to tell me that it has the best driver every-time I try and update it.If I plug the laptop in to the router with a wired connection it works just fine, so it is obviously an issue with the wireless adapter.what I should do in order to get this to take a new driver so it works again?
View 7 Replies View RelatedI'm unable to connect to the internet because my Dell Wireless 1390 WLAN Mini-Card says that "This device cannot start. (Code 10)"
I have an Dell Inspiron 1520.
I have a new 1921 router and when I try to use CP Express I get a Microsoft Internet Explorer error. Cisco CP Express Application could not be launced. If CP Epress is launched using https try the following steps and relaunch CP Express.
Disable TLS option in JRE Settings[Java Control Panel->Advanced ->Security]I have done this and still get the same error. I initially used the console port and assigned a user name and password per the warning message.
I normally use command line entries to setup my routers but this is first new router I have gotten in some time and am not familliar with the CP Express and thougt I would try it. Is there a way to load a default program that does not have all the CP Express data in it without manually removing it?
I am running WinXP Pro on a netbook which I have set up as a host with Real VNC. I connect well from all my Win 7 PC's. I do not want to just have remote access to that netbook. I would like to launch an application (which runs from MySQL) from the host which I can then use on the remote PC's display without that app actually launching and displaying on the host computer. At the moment, I can only see the desktop and remotely control it. Multiple connections are accepted but all see the same desktop
View 3 Replies View Relatedmy net book does not launch WiFi on startup. Wireless assistant button's light is not on. when i launch my comp it says me module(701) error.
View 1 Replies View RelatedAfter cleaning the PC from malware part of the settings in "Network connections" does not work. In auto mode everything is OK IP address is set and internet connection runs fine. When I tried to set it up manually - "right click" or "double click" on the connection, the PC stucks without message until "Ctr-Alt-Del". I know that reinstalling Windows will work, but I'm looking for easier way.
View 1 Replies View RelatedI have an access point 1310. I want to add to the WLC as an access point. It have been configured with IP address correctly and the radio interface is up. I need to add it to the WLC as CAPWAP.
View 5 Replies View RelatedIs it possible to de-auth a client, and then make sure they have to enter the passphrase if they want to connect again?
I just cant seem to find this option anywhere in my routers configuration page.
I recently bought a WRT120N Cisco router off of eBay. The seller, sadly, did not have the WiFi password or online interface username and password. I figured: 'Hey, no big deal, I'll just reset it.' I tried multiple times to no avail.I found out that is was a software issue. I looked up how to update the software, and what do you know? The only way I found to update the software was through the online interface.So, basically,I can't log into my router, can't reset it, and to do so, I need to access the interface which I can't do. How to possibly manually update the software of the router without the interface?
View 1 Replies View RelatedI am supporting a small cluster of AP541N WAPs and would like to know if there is an easy way to manually disconnect an associated client (recognized by MAC address) from the Associated Clients screen in the Access Point Configuration Utility Status view. That type of feature might come in handy with unruly bandwidth hogs down the road.
View 0 Replies View RelatedI am having trouble getting 1142 LAP to find the controller. We are running an ASA 5505 at our main campus where the 5508 is located. Each Of our distribution centers have a PIX501 and from there about 3-5 AP's each. The AP's that were primmed before instalation work great, however we need the ability to get the other ones that were already installed and not finding controller to work with out cycling them through main campus. I have opened up UDP ports 12222-12223 and 5246-5246 with no luck.
View 1 Replies View Relatedwe're evaulating the Cisco SM 4.2. After adding my ASA 5520 the Policies are discovered from the device except the RA VPN Policies.I tried to trigger the discovery process manually and i got this errormessage Please verify the device "IP address", "hostname", "domain name" and "port number" are correct, there is network connectivity between the CS Manager server and the device, and the device is configured to accept https connections, the device is running, and then retry this operation.which i don't understand because the other policies were retrieved just fine.
View 0 Replies View RelatedI have a problem discovering some ASA firewalls on a network. I have several ASA firewalls on this /24 network, but some of them I can't discover e.g 149.x.x.107 is discovered ok, but 149.x.x.20 I can't discover. It seems that it's not even trying to discover the devices I have problems with. Nothing is shown in the discovery log.
View 11 Replies View Relatedusing packet tracer, how can i find dns server ip address and i am having trouble pinging the desktops and server that i manually assigned the ip addresses to
View 2 Replies View RelatedI have a acer aspire 5741 with win7 and i5. i have no problems once i am connected to my network, the problem is the acer will only connect when i do it manually.i have changed the adapter settings to connect automatically numerous times but when i reboot, the settings always change back to connect manually. i have tried other networks but the acer will only connect manually. like i said, once connected it works fine it just will not do it automatically.
View 13 Replies View RelatedI had a malware attack and decided to reload my XP Media Edition on my Dell XPS 400 series. After the disc reformat and reload of XP from the operating system CD, and then loading the drivers CD, I cannot connect to the internet. The plug for the ethernet cable is red/yellow on two different jacks in the house. The modem is supplied by ATT U-verse. The TCP/IP is connected at 400 Mb/s but showing "0" data transfer in or out. The internet connection was working before the XP reload. I did not backup an "image" and so I may have lost my registries? Is there a way to "turn on" the ethernet port?
View 5 Replies View RelatedI accidently disconnected my wireless adapter, how do i reconnect.
View 1 Replies View RelatedHow do I set the time on my WAG320N manually. I have set the time zone, but the time shown is 04-01-2000 15:33:52, and I can't find anywhere to correct this.
View 8 Replies View RelatedBelkin F7D4302 will not connect to ISP if I try to manually set DNS entry. Once I attempt this I have to reset the router back to factory defaults before the router will connect with ISP
View 4 Replies View Related I've found an issue with my SRP527W that is prohibiting me setting up a useful site to site VPN. In short, the "Enable ID: Default/Manual" option in the IKE policy screen does not seem to behave as advertised. Not matter what it's set to the remote end always ends up receiving the IP address of the DSL interface as its peer id.
The scenario is an SRP527W with a dynamically assigned DSL IP address connecting to a Netscreen SSG5 on a static IP. I have confirmed that:
- A Main Mode VPN works (but is no use on an ongoing basis due to the dynamic IP)
- An aggressive mode VPN works if the Netscreen has its peer ID set to the public IP of the SRP (....same dynamic IP issue)
However if I try to set a manual Remote ID in the SRP IKE Policy it does not get sent as part of the phase 1 negotiations. Debug logs on the Netscreen shows that it receives the DSL public IP no matter what.
Dumping the router config to XML [URL] shows no sign of the IP address that has been set via the interface (despite the setting visibly staying set in the interface). The rest of the VPN config shows up there.
Current firmware version: 1.01.26 (003)