Manually Setup DNS IP On Every Device?
Apr 12, 2011
I've got the following problem using my DLink DSL-2740B with the latest firmware:On all my devices (Notebook, Netbook, iPhone, Set top Box, TV...) I need to manually set the IP of my internet providers DNS server or else, URL's can't be resolved. I'm pretty sure that the Router/Gateway is set up correctly as the status page of the router does show both the primary and secondary DNS servers IP addresses. Both have been automatically detected by the router.On my different devices, if I leave the DNS IP to be automatically detected, they will use the Routers IP as their DNS server IP (e.g. 192.168.1.1), which is the way it should be I'd think. However, trying to access (in browser or through ping or whatever) any URL, it just won't work. I need to manually enter the DNS's IP in the device.
View 1 Replies
ADVERTISEMENT
Apr 19, 2012
I have problem in recently installed LMS 4.1 Device discovery will not start when launched manually. When i hit the button, it doesn't even give a popup window saying that the discovery is started and that email will be sent... If I schedule it is launched, runs and finishes correctly. All proceses are started and it seems that application is working ok. LMS is installed on Win 2008 R2.
View 1 Replies
View Related
Mar 1, 2013
After cleaning the PC from malware part of the settings in "Network connections" does not work. In auto mode everything is OK IP address is set and internet connection runs fine. When I tried to set it up manually - "right click" or "double click" on the connection, the PC stucks without message until "Ctr-Alt-Del". I know that reinstalling Windows will work, but I'm looking for easier way.
View 1 Replies
View Related
May 20, 2013
N600 DB on OSX. I keep on reading the material that there is a link on the dashboard that I click on to set up the router manually. Nowhere on the dash board is that link. Where is that link?
View 1 Replies
View Related
Dec 13, 2011
I am having problems setting up a network, recently bought a used linksys router and had to restore to default settings. Now I am trying to set it up but I cant go to the ip 192.168... it times out, but when I go online and do the same thing I get a FW-1 at checky: Access denied. error. This is obviously my first time setting up a network using a router. what am I doing wrong? I checked drivers and I have tried plugging the cat5 into both internet and the 1st and 3rd port with little success, either a timed out connection or an error.
View 9 Replies
View Related
May 14, 2012
I am having a problem configuring NAT for a Linux device on our network. I am far from a Cisco expert but I have configured this many times in the past for Windows machines quite easily. I do this using the Cisco ASDM 5.2 for PIC GUI. All I needed to do for the Windows machines was:-setup the static NAT rule(inside ip translated to outside ip)-create a security policy(outside, incoming rule) to allow traffic to the outside ipand hey presto it works, ie: i can ping the outside ip and access the device remotely if I have allowed correct ports.I am not sure if this is the correct method but it was how i was shown and has worked many times in the past.But with this Linux device its no dice. The Linux device isnt a desktop but a mediator for industrial air conditioning controls. It runs a web server which we can view temperatures etc... through a browser. This works inside our network by browsing to the inside ip but I am trying to set it up to work outside of our network.
View 1 Replies
View Related
Jan 2, 2013
Here's the situation, 2 houses, house #1 has internet, DIR-665 connected to Cable modem, between the 2 houses CAT 6 cable, house #2 has DIR-655. Both houses need to offer wireless. How should the DIR-655 (house#2) be set up? (SSID/DHCP/UPNP/IP/GATEWAY/SUBNET, etc)?
View 1 Replies
View Related
Jul 30, 2012
I would like to use the Cisco ATA 186 as a SIP device with Cisco Call Manager 7. However, I have found that the SIP firmware for the Cisco ATA 186 is unsupported by Call Manager 7.Therefore, In order to use the ATA as a SIP device with the Call Manager, I believe I will need setup the ATA as a 3rd Party SIP device by doing the following:
1. Disable the TFTP option within the ATA, so that the SIP firmware is not overwritten by firmware from the TFTP server.
2. Install the 3.2.1 SIP firmware on the ATA, since the ATA is currently running the 3.2.4 SCCP firmware.
3. Register the ATA, as a third-party SIP device, with the Call Manager .Should I register the ATA as a 3rd party device?
View 2 Replies
View Related
Jan 4, 2012
I get internet through my Desktop using a wifi card that picks up the internet from my in-laws across the street (gets a really good signal btw). Anyway, that connection is perfectly fine, and up until recently I had been using a Hawking Range Extender to repeat the signal through my house connecting it to my PC's ethernet port and using the Internet Connection Sharing feature. For some reason that is beyond me it suddenly stopped working. Or rather, it will work for a couple minutes and then stop receiving packets.I'm thinking the device is faulty since it never actually worked that great to begin with. Is this type of setup possible for a wireless Router such as a lynksys device? Or would I need a repeater/range extender like I have been using?Again I would use the Wifi from my PC to share the connection with the Router to broadcast that signal through my house.
View 6 Replies
View Related
Mar 17, 2013
I need to setup new ACE 4710 device , after referring to "Establishing a Console Connection on the ACE" i had managed to set up initial console connection. During installtion i had configured vlan (default vlan 1000) , interface ip adess& subnet mask.
Post initial config i understand i should be able to open' Device Manager GUI Login Window' but it is not opening.I also need inputs on setting 4710 for the telnet connection
View 4 Replies
View Related
Jul 2, 2011
I've got a WAP610N access point and 4 WET610N to connect to it - however, no matter what I do when trying to install the WAP610N the setup tells me it cannot find the device.I've got the WAP610N connected to a homegateway (SAGEM) and my computer connected wired to the HGW. The HGW is setup as a DHCP server, everything beside the WAP610N works. It gets an IP address, and I can login to the web interface of the access point - but is still unable to use the setup and unable to connect any of the WET610N.
View 2 Replies
View Related
Jan 5, 2012
Steps to repeat the bug:
1) Physical Reset of SR520-FE to factory defaults
2) Run CCA 3.1(1) and connect to 192.168.75.1 using the default cisco/cisco login
3) Under the Home Menu, click the Device Setup Wizard
4) In Step 1, sellect the SR520 and observe that there is also a photograph of the SR520-FE(W) model displayed as feedback for Step 1
5) Try variations of Steps 2 through 4
Note: Step 4 has a problem because it says to plug the power into the device, but if the power was not already plugged in to begin with, we could not run the Device Setup Wizard in the first place.
6) Step 5 prompts for a user name and password.
BUG: No permutations of the documented default usernames and passwords "cisco" or "admin" work. The result is always the error dialog:Device Connectivity Status - "Failure: Not Connected.""Return to Step 1. Make sure that your PC is not connected to a network and you follow all the instructions."A search of the web indicates others are also had this unresolved issue with previous CCA releases.
View 1 Replies
View Related
Aug 30, 2012
Is it possible to de-auth a client, and then make sure they have to enter the passphrase if they want to connect again?
I just cant seem to find this option anywhere in my routers configuration page.
View 1 Replies
View Related
Oct 12, 2012
using packet tracer, how can i find dns server ip address and i am having trouble pinging the desktops and server that i manually assigned the ip addresses to
View 2 Replies
View Related
Feb 20, 2011
I have a acer aspire 5741 with win7 and i5. i have no problems once i am connected to my network, the problem is the acer will only connect when i do it manually.i have changed the adapter settings to connect automatically numerous times but when i reboot, the settings always change back to connect manually. i have tried other networks but the acer will only connect manually. like i said, once connected it works fine it just will not do it automatically.
View 13 Replies
View Related
Jun 29, 2011
I had a malware attack and decided to reload my XP Media Edition on my Dell XPS 400 series. After the disc reformat and reload of XP from the operating system CD, and then loading the drivers CD, I cannot connect to the internet. The plug for the ethernet cable is red/yellow on two different jacks in the house. The modem is supplied by ATT U-verse. The TCP/IP is connected at 400 Mb/s but showing "0" data transfer in or out. The internet connection was working before the XP reload. I did not backup an "image" and so I may have lost my registries? Is there a way to "turn on" the ethernet port?
View 5 Replies
View Related
Dec 23, 2011
I accidently disconnected my wireless adapter, how do i reconnect.
View 1 Replies
View Related
Sep 10, 2010
How do I set the time on my WAG320N manually. I have set the time zone, but the time shown is 04-01-2000 15:33:52, and I can't find anywhere to correct this.
View 8 Replies
View Related
Oct 21, 2012
Belkin F7D4302 will not connect to ISP if I try to manually set DNS entry. Once I attempt this I have to reset the router back to factory defaults before the router will connect with ISP
View 4 Replies
View Related
Apr 15, 2012
I have an access point 1310. I want to add to the WLC as an access point. It have been configured with IP address correctly and the radio interface is up. I need to add it to the WLC as CAPWAP.
View 5 Replies
View Related
Jan 30, 2013
I recently bought a WRT120N Cisco router off of eBay. The seller, sadly, did not have the WiFi password or online interface username and password. I figured: 'Hey, no big deal, I'll just reset it.' I tried multiple times to no avail.I found out that is was a software issue. I looked up how to update the software, and what do you know? The only way I found to update the software was through the online interface.So, basically,I can't log into my router, can't reset it, and to do so, I need to access the interface which I can't do. How to possibly manually update the software of the router without the interface?
View 1 Replies
View Related
Oct 22, 2012
how do i determine the ip address manually when installing my hp printer. model ; P3005x
View 3 Replies
View Related
Jun 14, 2011
I got a new HP laptop running Windows 7. When I turn on my laptop, my wireless is off. So I click on F12 (my wireless button), to activate my wireless. The orange light turns blue. Even though the light indicates that my wireless is on, I have to go to device manager>networking>802.11n>advanced then activate my radio for my laptop to pick up the wireless signals. The problem is that I have to do this every time I turn on my laptop, and its getting quite repetitive.
View 4 Replies
View Related
Jul 20, 2011
I am supporting a small cluster of AP541N WAPs and would like to know if there is an easy way to manually disconnect an associated client (recognized by MAC address) from the Associated Clients screen in the Access Point Configuration Utility Status view. That type of feature might come in handy with unruly bandwidth hogs down the road.
View 0 Replies
View Related
Jun 4, 2011
I have a window 7 acer laptop, 3 as a matter of fact, i just upgraded to charter high speed internet and i have this new router its called ubee router/modem i have no trouble with my window xp with the wire less connection, but on the 3 windows 7 computers they will drop or lose the wireless conection and we have to refresh the network and it will do okay untill its shut off and it might connect, charter. If i use a direct cable no problems at all. even if i set the router up with no wepkey it will still drop wireless umm what could i do to correct this
View 1 Replies
View Related
Aug 23, 2011
I recently upgraded my WRT610N to Firmware Version: 2.00.01 and now the unit powers down on its own after a few hours. Are there any known issues with this firmware?Is there any way to roll back to the previous version of the firmware?
View 4 Replies
View Related
Nov 9, 2012
Region : Hongkong
Model : TL-MR3220
Hardware Version : V1
Firmware Version : 3.14.2 Build 120822 Rel.57775n
ISP : 123
In order to use public IP provided by the ISP, I have to enter the specific APN.It's however no matter what I type in the field of the APN, the router is still connected to the default APN settings from ISP.I have tried typed wrong string in the field of APN, the router is still connected to the default APN successfully.
View 6 Replies
View Related
May 18, 2012
I've found an issue with my SRP527W that is prohibiting me setting up a useful site to site VPN. In short, the "Enable ID: Default/Manual" option in the IKE policy screen does not seem to behave as advertised. Not matter what it's set to the remote end always ends up receiving the IP address of the DSL interface as its peer id.
The scenario is an SRP527W with a dynamically assigned DSL IP address connecting to a Netscreen SSG5 on a static IP. I have confirmed that:
- A Main Mode VPN works (but is no use on an ongoing basis due to the dynamic IP)
- An aggressive mode VPN works if the Netscreen has its peer ID set to the public IP of the SRP (....same dynamic IP issue)
However if I try to set a manual Remote ID in the SRP IKE Policy it does not get sent as part of the phase 1 negotiations. Debug logs on the Netscreen shows that it receives the DSL public IP no matter what.
Dumping the router config to XML [URL] shows no sign of the IP address that has been set via the interface (despite the setting visibly staying set in the interface). The rest of the VPN config shows up there.
Current firmware version: 1.01.26 (003)
View 1 Replies
View Related
Jun 25, 2011
I am doing an evaluation of LMS 4.0. I have loaded the system on Windows and manually added my core 3750 switch into the system. Device availability is showing the device as available. However, the other pollers like link utilization, error count, etc. all show that there is no data. When I go into the poller config, the pollers for link utilization and errors show 0 devices associated and a status of "instance not found". The CPU and availability pollers show active with my one device added. I have verified the credentials and if I go into Inventory -> Port and module and select my 3750 I do get a list of all the interfaces and the descriptions so LMS is connecting to the switch and pulling data.
So how do I get the pollers for link utilization and errors to start populating data?
Second question, during install I did configure the software update section and it said there was an LMS 4.0.1 available which I told it to download. Now I have a psu_download directory and some more directories like cm, cmf, etc. but I don't see any file on what to do with them. What do I need to do to install the new package files that were downlaoded to psu_download?
View 4 Replies
View Related
Mar 16, 2013
My wireless network consists mainly of approximately 1400 AP's 900 x 3602's, 500 x 3502's,The majority of these AP's especially the new ones have been manually optimised for channel and power settings. We paid an external surveyor to survey and optimise the AP's.
We have a few 5505 WLC's and the channel assignment method is set to "Freeze" ,My question is, if someone invokes a channel update on a WLC, will the WLC override the original manual channel setting if the WLC thinks it should be changed? And will the original setting be lost forever unless a restore is performed from the WLC Database?
View 5 Replies
View Related
Jan 17, 2013
I was looking for a way the manually re-authenticate dot1x client from cli and found this: [URL]
"You manually reauthenticate the client by entering the dot1x reauthenticate interface interface-id privileged EXEC command"
I've tried it 2960 with 12.2(58)SE and 15.0(2)SE, but it doesn't seems to be implemented. Have I missunderstood something? Or do you guys have any other command to accomplish a manually re-auth?
View 6 Replies
View Related
Jan 27, 2013
I have 3 WAP321, all set to uk time zone, all the settings restor apart from the time on reboot that defaults back to 1999 despite NTP server listed, interestingly have to manually reset time to present before NTP will update it
View 1 Replies
View Related
Dec 28, 2011
I have a Netgear ProSafe FVS318 wireless router whose login information I have lost. I have attempted to manually reset it using the reset button on the back, and return it to factory default settings (thus resetting the login information to admin/password).I have checked everywhere, including the documentation for the router itself. I have gotten multiple instructions on how to reset it (generally telling me to hold the button down for anywhere from 10 seconds to 30 seconds until the test light blinks or stays solid and then blinks or stays solid again, or telling me to hold down the button while turning it on). None of these methods have worked. The router still will not reset. It never reboots no matter how long I hold down the button, no matter when I release it, no matter what the orange "test" light is doing, and no matter if I begin with the router on or off. It will not reboot and I still cannot login.
The orange "test" light has behaved the same way each time; after 10 seconds, it turns solid, and then begins blinking before turning back off. After 20 seconds, it turns solid, and then turns off. It does this if I hold the reset button down for 10 seconds, regardless of whether or not I release the button after it first turns solid. If I continue to hold down the reset button, it continues this pattern indefinitely, for as long as the button is held. When I turn the router on, it turns solid before turning off, regardless of whether I am holding the rest button down. Its behavior never deviates from the observed patterns regardless of what I do. At no point has the router ever rebooted on its own.The default login should be admin/password, as this information is included on the bottom of the router, and in its documentation.
View 14 Replies
View Related
