After cleaning the PC from malware part of the settings in "Network connections" does not work. In auto mode everything is OK IP address is set and internet connection runs fine. When I tried to set it up manually - "right click" or "double click" on the connection, the PC stucks without message until "Ctr-Alt-Del". I know that reinstalling Windows will work, but I'm looking for easier way.
View 1 RepliesI've got the following problem using my DLink DSL-2740B with the latest firmware:On all my devices (Notebook, Netbook, iPhone, Set top Box, TV...) I need to manually set the IP of my internet providers DNS server or else, URL's can't be resolved. I'm pretty sure that the Router/Gateway is set up correctly as the status page of the router does show both the primary and secondary DNS servers IP addresses. Both have been automatically detected by the router.On my different devices, if I leave the DNS IP to be automatically detected, they will use the Routers IP as their DNS server IP (e.g. 192.168.1.1), which is the way it should be I'd think. However, trying to access (in browser or through ping or whatever) any URL, it just won't work. I need to manually enter the DNS's IP in the device.
View 1 Replies View Relatedhow do i determine the ip address manually when installing my hp printer. model ; P3005x
View 3 Replies View RelatedRegion : Ireland
Model : TD-W8960N
Hardware Version : V4
Firmware Version : TD-W8960N
ISP : Vodafone Ireland
I am having a rather annoying problem. I run a small hotel (just 3 floors) and my modem gives a strong enough signal to provide wireless access to everybody in the house however I'm finding that a lot of people, whilst they can connect to the modem, cannot browse online. Connection just times out when they open their browsers.Recently a guest gave me his laptop and asked me if I could do anything with it. I'm by no means an expert when it comes to this kind of thing so I chanced my arm by putting his MAC address into the CP's Wireless/MAC Filter page. He connected immediately and was able to go online much to my relief.
Thing is, I don't want to have to do this for every guest that comes through my door! Is there any way everybody who has a laptop can connect without me manually entering their MAC addresses? MAC restrict mode is set to 'disabled' but I thought that would allow everybody unrestricted access?
N600 DB on OSX. I keep on reading the material that there is a link on the dashboard that I click on to set up the router manually. Nowhere on the dash board is that link. Where is that link?
View 1 Replies View RelatedI am having problems setting up a network, recently bought a used linksys router and had to restore to default settings. Now I am trying to set it up but I cant go to the ip 192.168... it times out, but when I go online and do the same thing I get a FW-1 at checky: Access denied. error. This is obviously my first time setting up a network using a router. what am I doing wrong? I checked drivers and I have tried plugging the cat5 into both internet and the 1st and 3rd port with little success, either a timed out connection or an error.
View 9 Replies View RelatedUsing LMS 4.1 with an address that are natted I see that SWIM-jobs to fetch IOS-images are using the server's "un-natted" address.Can't find how to setup the nat-address in LMS so the devices uses that one instead when communicating with the server with scp for instance..
I believe this was possible in LMS 3.x, but how is it configured in LMS 4.1?
I have a network printer which is connected to unmanaged switch, then unmanaged switch is then connected to one of the slots on the router (to get internet access). I use the program Free IP Scanner to look for the IP so then I can find the IP address of my printer. Then I would go to Port setting of the printer and change. Every week or month I have to do this. Two things I would like to know:
1. I have a 2003 server which is not connected or active yet. it's just sitting there running but no computers or printers are connected yet. How do I make this to be a printer server and solved my issue of having keep tracing the IP for my printer?
2. If not using the server, how would I setup my printer IP address to be permanent?
I am trying to set up a new notebook and it can't find the IP Address. I do not know my IP address or remember my password. My server is BK Mom.
View 1 Replies View Relatedi need to add a lot of mac addresses in mac addr filter table. many routers do not allow me to add a note for each mac address. that makes management a bit difficult.
eg.
field 1, field 2, enable
xx:xx:xx:xx:xx:xx , peter pc, y
xx:xx:xx:xx:xx:xx, mary pc, n
Le Pan 2 tablet keeps trying to "obtain IP address." I have a dlink 655 router. I've removed the password from the router. Rarely will the tablet connect.
View 1 Replies View RelatedI have 3 Dcs-3420's on the same network same static ip setup and they never have issues. Im testing 1 942L, I've upgraded firmware to1.11, but periodically the camera loses its ip address which is weird because it is set static. My wireless is set to Mac address security. Now camera is outside in a shaded area, over night the camera worked all night, this morning it has reset three times. Additionally, each time it resets/losses ip address it also loses the manually set time.
View 1 Replies View RelatedIs it possible to de-auth a client, and then make sure they have to enter the passphrase if they want to connect again?
I just cant seem to find this option anywhere in my routers configuration page.
I want to setup a static ip address for a h.264 network dvr ,however my desktop computer is out of order, that is connected direct to router,is it possible to use my wireless laptop to setup the router,or will I have to connect the eithernet cable to the laptop.
View 4 Replies View RelatedI wanted to know if you can setup reserved wireless IP address on the WRT54G router. With all the kids devices, when I reset the router, getting all the devices online is a challage. Some end up with duplicate IP address causing conflicts. If I could reserve an IP address for a specific device. Let me know what option the router has?
View 3 Replies View RelatedThe browser-based settings utility for my E1200 can't setup MAC address filtering. I go to the "Wireless MAC Filter" page and enable MAC filtering.When I click the “wireless client list” button, a new window opens saying “IE cannot display the webpage”. This always happens when I have a wireless connection active.When there are no active connections, then IE properly displays the MAC address table, but it is empty since there aren't any computers connected to the router.
View 5 Replies View RelatedI am trying to configure the ACS with AD in the identity store but am running into the following issue.I enter the AD Domain Name and username and password and hit the 'Test Connection' button and receive a DNS error stating that it 'Cannot resolve network address'.I have logged into the CLI and test to the domain name from there and it works fine.
View 5 Replies View RelatedI am using LMS 4.0.1 to monitor the data center network devices. I have two core switches, each core switch has an ACE module installed on it. I have configured many virtual context on each ACE module, and these ACE contexts are acting as primary and standby roles. The problem i faced with is LMS reports the virtual ip address configured on each ace context as duplicate ip address, and i didn't know how to deal with it. As to my understanding, this should be the normal behavior due to my setup, but how can i remove this alarm on LMS 4.0.1?
View 1 Replies View Relatedusing packet tracer, how can i find dns server ip address and i am having trouble pinging the desktops and server that i manually assigned the ip addresses to
View 2 Replies View RelatedI have a acer aspire 5741 with win7 and i5. i have no problems once i am connected to my network, the problem is the acer will only connect when i do it manually.i have changed the adapter settings to connect automatically numerous times but when i reboot, the settings always change back to connect manually. i have tried other networks but the acer will only connect manually. like i said, once connected it works fine it just will not do it automatically.
View 13 Replies View RelatedI had a malware attack and decided to reload my XP Media Edition on my Dell XPS 400 series. After the disc reformat and reload of XP from the operating system CD, and then loading the drivers CD, I cannot connect to the internet. The plug for the ethernet cable is red/yellow on two different jacks in the house. The modem is supplied by ATT U-verse. The TCP/IP is connected at 400 Mb/s but showing "0" data transfer in or out. The internet connection was working before the XP reload. I did not backup an "image" and so I may have lost my registries? Is there a way to "turn on" the ethernet port?
View 5 Replies View RelatedI accidently disconnected my wireless adapter, how do i reconnect.
View 1 Replies View RelatedHow do I set the time on my WAG320N manually. I have set the time zone, but the time shown is 04-01-2000 15:33:52, and I can't find anywhere to correct this.
View 8 Replies View RelatedBelkin F7D4302 will not connect to ISP if I try to manually set DNS entry. Once I attempt this I have to reset the router back to factory defaults before the router will connect with ISP
View 4 Replies View RelatedI have an access point 1310. I want to add to the WLC as an access point. It have been configured with IP address correctly and the radio interface is up. I need to add it to the WLC as CAPWAP.
View 5 Replies View RelatedISP assigned us the following:xxx.yyy.zzz.32/30 as the outside interface network.This means .33 is the next hop, gateway, or default route.This means .34 is the outside interface on the ASA.xxx.yyy.zzz.64/26 as the ip address pool.This means xxx.yyy.zzz.65 to xxx.yyy.zzz.127 is the address pool.xxx.yyy.zzz is identical in all cases.Addresses .35 through .63 are owned by other parties and are not usable to us.The 33-34 setup works using static routing - IPSEC VPN is setup and functioning properly using these addresses.
[ie. Route outside 0.0.0.0 0.0.0.0 xxx.yyy.zzz.33]
After NAT and ACL entries are created to provide altnernate external IP address on the outside interface [ie. static (inside,outside) [external ip] [name] netmask 255.255.255.255 and access-list [name2] extended permit tcp any host [alternate outside ip] eq https], attempting to browse to an internally hosted website from an external IP address results in the following messages in the ASDM log.
6 Apr 14 2011 17:58:51 110003 [redacted external IP Address] 37763 [Internal Website Name] 80 Routing failed to locate next hop for TCP from Outside:[redacted external IP Address]/37763 to Inside:[Internal Website Name]/80
How do I setup routing for this non contiguous address range?
I have a RV082.I need to set up a VPN form outside to use a Static address from the Lan side of the RV082.
Lan is 172.16.0.126
Wan is 10.161.48.1
The computer using the VPN will need a virtual IP on the Lan of the RV082 so that it is seen as being on the same network as the equipment on the LAN.
I recently bought a WRT120N Cisco router off of eBay. The seller, sadly, did not have the WiFi password or online interface username and password. I figured: 'Hey, no big deal, I'll just reset it.' I tried multiple times to no avail.I found out that is was a software issue. I looked up how to update the software, and what do you know? The only way I found to update the software was through the online interface.So, basically,I can't log into my router, can't reset it, and to do so, I need to access the interface which I can't do. How to possibly manually update the software of the router without the interface?
View 1 Replies View RelatedI got a new HP laptop running Windows 7. When I turn on my laptop, my wireless is off. So I click on F12 (my wireless button), to activate my wireless. The orange light turns blue. Even though the light indicates that my wireless is on, I have to go to device manager>networking>802.11n>advanced then activate my radio for my laptop to pick up the wireless signals. The problem is that I have to do this every time I turn on my laptop, and its getting quite repetitive.
View 4 Replies View RelatedI am supporting a small cluster of AP541N WAPs and would like to know if there is an easy way to manually disconnect an associated client (recognized by MAC address) from the Associated Clients screen in the Access Point Configuration Utility Status view. That type of feature might come in handy with unruly bandwidth hogs down the road.
View 0 Replies View RelatedI have problem in recently installed LMS 4.1 Device discovery will not start when launched manually. When i hit the button, it doesn't even give a popup window saying that the discovery is started and that email will be sent... If I schedule it is launched, runs and finishes correctly. All proceses are started and it seems that application is working ok. LMS is installed on Win 2008 R2.
View 1 Replies View RelatedI am trying to set up a static IP address for my Toshiba Satellite L350 Wireless Laptop on Windows 7. My Broadband is on TalkTalk (UK) Huawai Echo-Life HG520b. I tried many sites but it never seems to work.
View 1 Replies View RelatedI have a window 7 acer laptop, 3 as a matter of fact, i just upgraded to charter high speed internet and i have this new router its called ubee router/modem i have no trouble with my window xp with the wire less connection, but on the 3 windows 7 computers they will drop or lose the wireless conection and we have to refresh the network and it will do okay untill its shut off and it might connect, charter. If i use a direct cable no problems at all. even if i set the router up with no wepkey it will still drop wireless umm what could i do to correct this
View 1 Replies View Related