Using LMS 4.1 with an address that are natted I see that SWIM-jobs to fetch IOS-images are using the server's "un-natted" address.Can't find how to setup the nat-address in LMS so the devices uses that one instead when communicating with the server with scp for instance..
I believe this was possible in LMS 3.x, but how is it configured in LMS 4.1?
After cleaning the PC from malware part of the settings in "Network connections" does not work. In auto mode everything is OK IP address is set and internet connection runs fine. When I tried to set it up manually - "right click" or "double click" on the connection, the PC stucks without message until "Ctr-Alt-Del". I know that reinstalling Windows will work, but I'm looking for easier way.
View 1 Replies View RelatedI have a network printer which is connected to unmanaged switch, then unmanaged switch is then connected to one of the slots on the router (to get internet access). I use the program Free IP Scanner to look for the IP so then I can find the IP address of my printer. Then I would go to Port setting of the printer and change. Every week or month I have to do this. Two things I would like to know:
1. I have a 2003 server which is not connected or active yet. it's just sitting there running but no computers or printers are connected yet. How do I make this to be a printer server and solved my issue of having keep tracing the IP for my printer?
2. If not using the server, how would I setup my printer IP address to be permanent?
I am trying to set up a new notebook and it can't find the IP Address. I do not know my IP address or remember my password. My server is BK Mom.
View 1 Replies View Relatedi need to add a lot of mac addresses in mac addr filter table. many routers do not allow me to add a note for each mac address. that makes management a bit difficult.
eg.
field 1, field 2, enable
xx:xx:xx:xx:xx:xx , peter pc, y
xx:xx:xx:xx:xx:xx, mary pc, n
I am trying to configure the ACS with AD in the identity store but am running into the following issue.I enter the AD Domain Name and username and password and hit the 'Test Connection' button and receive a DNS error stating that it 'Cannot resolve network address'.I have logged into the CLI and test to the domain name from there and it works fine.
View 5 Replies View RelatedI am using LMS 4.0.1 to monitor the data center network devices. I have two core switches, each core switch has an ACE module installed on it. I have configured many virtual context on each ACE module, and these ACE contexts are acting as primary and standby roles. The problem i faced with is LMS reports the virtual ip address configured on each ace context as duplicate ip address, and i didn't know how to deal with it. As to my understanding, this should be the normal behavior due to my setup, but how can i remove this alarm on LMS 4.0.1?
View 1 Replies View RelatedLe Pan 2 tablet keeps trying to "obtain IP address." I have a dlink 655 router. I've removed the password from the router. Rarely will the tablet connect.
View 1 Replies View RelatedI have 3 Dcs-3420's on the same network same static ip setup and they never have issues. Im testing 1 942L, I've upgraded firmware to1.11, but periodically the camera loses its ip address which is weird because it is set static. My wireless is set to Mac address security. Now camera is outside in a shaded area, over night the camera worked all night, this morning it has reset three times. Additionally, each time it resets/losses ip address it also loses the manually set time.
View 1 Replies View RelatedISP assigned us the following:xxx.yyy.zzz.32/30 as the outside interface network.This means .33 is the next hop, gateway, or default route.This means .34 is the outside interface on the ASA.xxx.yyy.zzz.64/26 as the ip address pool.This means xxx.yyy.zzz.65 to xxx.yyy.zzz.127 is the address pool.xxx.yyy.zzz is identical in all cases.Addresses .35 through .63 are owned by other parties and are not usable to us.The 33-34 setup works using static routing - IPSEC VPN is setup and functioning properly using these addresses.
[ie. Route outside 0.0.0.0 0.0.0.0 xxx.yyy.zzz.33]
After NAT and ACL entries are created to provide altnernate external IP address on the outside interface [ie. static (inside,outside) [external ip] [name] netmask 255.255.255.255 and access-list [name2] extended permit tcp any host [alternate outside ip] eq https], attempting to browse to an internally hosted website from an external IP address results in the following messages in the ASDM log.
6 Apr 14 2011 17:58:51 110003 [redacted external IP Address] 37763 [Internal Website Name] 80 Routing failed to locate next hop for TCP from Outside:[redacted external IP Address]/37763 to Inside:[Internal Website Name]/80
How do I setup routing for this non contiguous address range?
I have a RV082.I need to set up a VPN form outside to use a Static address from the Lan side of the RV082.
Lan is 172.16.0.126
Wan is 10.161.48.1
The computer using the VPN will need a virtual IP on the Lan of the RV082 so that it is seen as being on the same network as the equipment on the LAN.
I want to setup a static ip address for a h.264 network dvr ,however my desktop computer is out of order, that is connected direct to router,is it possible to use my wireless laptop to setup the router,or will I have to connect the eithernet cable to the laptop.
View 4 Replies View RelatedI wanted to know if you can setup reserved wireless IP address on the WRT54G router. With all the kids devices, when I reset the router, getting all the devices online is a challage. Some end up with duplicate IP address causing conflicts. If I could reserve an IP address for a specific device. Let me know what option the router has?
View 3 Replies View RelatedThe browser-based settings utility for my E1200 can't setup MAC address filtering. I go to the "Wireless MAC Filter" page and enable MAC filtering.When I click the “wireless client list” button, a new window opens saying “IE cannot display the webpage”. This always happens when I have a wireless connection active.When there are no active connections, then IE properly displays the MAC address table, but it is empty since there aren't any computers connected to the router.
View 5 Replies View RelatedI am trying to set up a static IP address for my Toshiba Satellite L350 Wireless Laptop on Windows 7. My Broadband is on TalkTalk (UK) Huawai Echo-Life HG520b. I tried many sites but it never seems to work.
View 1 Replies View RelatedIs there a way to set up Quick VPN on the RV120W without changing the internal subnet? I have just taken over responsibility for a network and I don't know all of the nooks and crannies yet, so I'd rather not change the internal sub net. I've tried setting up a user then changing the LAN settings afterward, but it automatically removed the VPN user when I did so.
View 1 Replies View RelatedI've just purchased a couple of SRP527W routers. I've been unable to even browse to the default 192.168.15.1 to start my configuration. My local network is 192.168.1.x. At risk of showing my stupidity, what am I doing wrong.
View 5 Replies View RelatedI am having an issue where occasionally the Sidewinder starts to see my internal RFC 1918 address instead of the configured external address of my firewall. This is for peering between the two. The error they see on the Sidewinder is:So instead of seeing the external peer address he sees a 10.220.3.18 address. We are not sure what triggers this becuase normally he see's my 63.117.98.222 address.
View 5 Replies View RelatedI have an old ASA 5505, and I'm having some trouble with Nat Hairpinning. I've done this with other firewalls before and I am having no luck now. I have an internal address that I wish to forward from an external address- so if someone goes to 123.456.789.012:3456 then it will forward to 192.168.1.244:92 (All numbers are arbitrary here- only for illustration). I have and Access Rule and NAT and PAT set up so that I can get in if I originate from outside the LAN. What I am trying to do is to have this work from inside the LAN as well- so that if I am at my desk, and I connect a device and type in 123.456.789.012:3456, it will deliver the content at 192.168.1.244:92. The problem I am having is that it just isn't working, and I cannot figure out why- When I started here, there was an address configured to work this way, and it still works- I just cannot find what is different between what I am doing and what the person who configured it did.
View 7 Replies View RelatedIs it possible using any module in CW to get the MAC address and IP address of all switchports on a 6500?
View 6 Replies View RelatedI switched from Time Capsule with AirPort to E2000 and have a problem with configuration.I use the same IPs as in AirPort and E2000 gives me an error:"The WAN IP address cannot be the same subnet as the Guest Network IP address" and I can't save configuration.But in my opinion they are different.I use "Static IP" option and I have IPs from my ISP: [code] So WAN IP is different subnet as LAN and I don't know what to do now. It worked with these settings in AirPort and here I can't proceed.
View 2 Replies View RelatedIs it possible to assign public IP address as Router's local IP address (RVL200, RVS4000)?
View 1 Replies View RelatedI have a Linksys WRT54GS v5.1 router running firmware 1.52.5.I am trying to use Linksys IP Phones SPA942, but these do not seem to be able to log on and just show "Initializing network" even though the MAC address appears in the router with an IP address.The strange thing is that I already have 4 SPA941 phones that work with no problem and just log on to the network.Is there something about the SPA942 that I need to configure differently, I have factory reset it with sucess, but still unable to log on to the network.
View 1 Replies View RelatedOn my cisco IOS 12.4 router,Can i make it so only lets say mac address 11:22:33:44:55:66 able to use ip address 10.10.10.2?I want this so that only this IP can configure servers, and so if the computer using it is turned off, any other device cannot use the IP address.
View 6 Replies View RelatedI recently configured and installed a 1941ISR for a customer. The customer purchased a 25-User SSLVPN license with the router, and I configured it for remote SSLVPN access. This is working nicely except for one issue: when users initiate an SSLVPN connection request by browsing to the assigned webvpn gateway IP, they get the "There is a problem with this website's security certificate" browser message. They are in the process of working with their DNS hosting provider to get a DNS entry assigned to the IP address so the users won't have to specify an IP address in the URL address box, but they will continue to get the certificate error until/unless I can figure out how to resolve the issue.
I've tried the following "How to make IE8 trust a self-signed certificate in 20 irritating steps" that I found via another forum link but with no luck:
1.Browse to the site whose certificate you want to trust.
2.When told "There is a problem with this website's security certificate.", choose "Continue to this website (not recommended)."
3.Select Tools->Internet Options.
4.Select Security->Trusted sites->Sites.
5.Confirm the URL matches, and click "Add" then "Close".
6.Close the "Internet Options" dialog box with either "OK" or "Cancel".
7.Refresh the current page.
8.When told "There is a problem with this website's security certificate.", choose "Continue to this website (not recommended)."
9.Click on "Certificate Error" at the right of the address bar and select "View certificates".
10.Click on "Install Certificate...", then in the wizard, click "Next".
11.On the next page select "Place all certificates in the following store".
12.Click "Browse", select "Trusted Root Certification Authorities", and click "OK".
13.Back in the wizard, click "Next", the "Finish".
14.If you get a "Security Warning" message box, click "Yes".
15.Dismiss the message box with "OK".
16.Select Tools->Internet Options.
17.Select Security->Trusted sites->Sites.
18.Select the URL you just added, click "Remove", then "Close".
19.Now shut down all running instances of IE, and start up IE again.
20.The site's certificate should now be trusted.
I followed all 20 irritating steps to the letter, but am still getting the security certificate nat.Now when I “Continue to this website (not recommended)” and click on "Certificate Error" at the right of the address bar, the certificate error windows says “Mismatched Address”.Is there a way that I can get this fixed without resorting to a 3rd party CA?
I have been trying to clone my PC's MAC onto my Linksys WAG120N adsl2+ modem router .
I click the the clone my PC's MAC button in the MAC address clone tab. I get the following error :
"Mac address cannot be the multicast address"
The MAC address starts with 1C:C1:XX:XX:XX:XX
I even tried to update the firmware.
I recently switched routers to the DIR-615 and I'm trying to troubleshoot why one of our laptops keeps losing the IP address and gets a self-assigned IP address. I see the following messages in the log, I am wondering if the reason codes are listed and explained somewhere? I tried searching the manual but could not find any information.
View 9 Replies View RelatedWe have an ADSL connection and use a D-Link DSL-320B modem. We have a D-Link DIR-120 router connected to this modem. This has worked perfectly fine up until today when we disconnected the router and connected a computer (call it A) directly to the modem because it was getting an unusable connection through the router for some reason. We later also performed a factory reset on the DIR-120 router.
Unfortunately, after the above steps the router did not receive any IP address (through DHCP) from the ADSL connection anymore. During my attempts to debug this I noticed that my laptop (call it B) didn't get any IP address either (when connected directly to the modem). I noticed the following syslog entries repeating over and over while trying to connect: [code]
At this point computer A could still get a connection just fine tho (when connected directly to the modem).
I then tried to change the MAC address of the router to an arbitrary one (a copy of computer B's MAC address but with the last digit increased by one). The router still did not get assigned any IP address. Finally I tried making the router clone the MAC address of a third computer (call it C). C has never been connected directly to the modem. Doing this worked. After cloning the MAC address of computer C the router is immediately assigned an IP address and the internet connection works as it did prior to all this.
Now, my question is, why would computer B and the original MAC address of the router not be able to get an IP address while two other computers worked just fine? Why would changing to an arbitrary MAC address not work while cloning the MAC address of another computer did? Could the router's MAC address have been blocked by the ISP for some reason (and what could cause this)?
but my situation seems more like a blacklisting of some MAC addresses rather then allowing just a single MAC address.
I need to change the ip address on my router same ip address as myDlink router?
View 6 Replies View RelatedWe are trying to setup a Cisco SSL VPN. When outside of the network and after logging in the web page, you have the option to Remote Control your PC at the office. When clicking that, it takes you to the login screen with MACHINEuser... Is there any way to make DOMAINuser default or even just automatically login since you've just logged in the VPN anyway?
View 2 Replies View RelatedHow to set up vpn in cisco 871 k-9 and make connection from internet to cisco by using vpn?How to set up vpn client? Do I need certificate for this? Do I need to run pki server on cisco?
View 5 Replies View RelatedHow to setup LMS4.1 soft appliance in a HA (active/standby) setup? Config guides only mentions windows and solaris setup using HA but nothing about the soft appliance. I am guessing that I would only need license on the active box.
View 1 Replies View RelatedI'm trying to setup my DMZ so all my servers will have public IPs assigned to them. I'm currently trying to use two interfaces on each server, one with a private IP and then one with a public IP. All my internal traffic will go over the private interfaces...this is working. However, I'm having a problem trying to get it so the public interfaces work. Ultimately, these will be VM Hosts and have VM guests on them, each guest will have it's own public IP.
View 14 Replies View Related