Linksys Wired Router :: WRT54GS V5.1 MAC Address Appears With IP Address
Jul 3, 2011
I have a Linksys WRT54GS v5.1 router running firmware 1.52.5.I am trying to use Linksys IP Phones SPA942, but these do not seem to be able to log on and just show "Initializing network" even though the MAC address appears in the router with an IP address.The strange thing is that I already have 4 SPA941 phones that work with no problem and just log on to the network.Is there something about the SPA942 that I need to configure differently, I have factory reset it with sucess, but still unable to log on to the network.
View 1 Replies
ADVERTISEMENT
Feb 28, 2011
Is it possible to assign public IP address as Router's local IP address (RVL200, RVS4000)?
View 1 Replies
View Related
Apr 9, 2013
To connect the Linksys WRT54GS to a Microchip DV102411 WiFi Comm Demo Board I need the IP address assigned by DHCP. The WRT54GS Administration Log is enabled but there is no Incoming or Outgoing network activity. The DV102411 sees the SSID linsys when scanning for wireless networks and attaches to it but once attached I need to know the IP address the DV102411 has been given by the WRT54GS.
View 2 Replies
View Related
Mar 1, 2012
I have a wrt54gs v7 and a wap54g v3.1. Both have latest firmware on them. I set the access point to act as a repeater and entered the mac address from the router (It said to use the lan mac address. is that right?). I have them set on same subnet with static ip addresses. They have same wireless ssid and password with one using channel 10 and the other using channel 2. I can receive an ip address from the router and connect to internet. I cannot get an ip address from the access point. I tried a static ip on the computer and it will connect, but I don't have internet. Am I missing something in the setup? Can this access point act as a repeater for this router?
View 3 Replies
View Related
Jul 3, 2011
Is there an alternate way to get the DNS settings off of the router? I've followed all of the steps up above, but I cannot set up a static IP Address on my computer without knowing the routers DNS settings, which I cannot retrieve from the web-based setup due to the corrupt firmware.
View 2 Replies
View Related
Jan 19, 2011
I just want to allow specified computers wired access to the internet via the E1000 router. Here is the problem I am currently working on:
(1) Setup the E1000 unit to allow only one PC 'C1' (MAC: 91:E6:BA:25:91:58) wired access to the internet.
(2) Add another PC (unknown MAC address) to the LAN side of the E1000 unit and see if it is being blocked by the 'Access Restriction' policy that was setup.
(3) Can’t get the above done – the second PC is able to surf the internet although the policy is enabled.
Notes:(a) Ref: 'Access Restrictions' web page or see Page 26 in the User Guide .(b) The unit has the latest firmware already installed: Firmware Version: 2.1.01 build 5Dec 3, 2010.(c) The internet port of the unit goes to the ADSL modem in my house.(d) Unplugged the unit for 10 seconds as advised by one of your technicians, still no difference.(e) I can deny PCs, but the allowing only specified ones seems not to be doing anything.By the way, can the E3000 or E4200 do the above?
View 9 Replies
View Related
Jun 1, 2011
I am attempting to access a VPN hosted on Windows 2003 Server using my Windows 7 SP1 / 64 bit laptop. I can establish the connection and even open Outlook and connect to the exchange server on the remote network. It seems that whenever I try to move files up or down or open Internet Explorer, the following sequence of events happens:
1) Connection between my local router (BEFRS41) and the internet is dropped.
2) The IP address on my local network adaptor changes to an unknown number (169.254.180.72) - is normally 192.168.1.104
3) The VPN connection drops and attempts to re-dial, but of course fails because my connection tot he internet has been broken.
Since I'm accessing rather than hosting the VPN, I'm not sure if I have to adjust any of the router settings.
View 3 Replies
View Related
Nov 10, 2011
My printer (HP7210) is wired connected to my WRT54GL router. 2 computers have also a wired connection, my laptop is connected wireless. All these computers use the connected printer. 2 computers can only use a static IP-address for the printer. How can I set a static IP address in my router?
View 3 Replies
View Related
Feb 28, 2012
I was able to install the RV042 router to my ATT DSL line (WAN1 port-INTERNET) and it gets an external IP address automatically and the Internet works. When I connect my Comcast Internet to WAN2 port INTERNTE/DMZ) it doesn't get an IP address. and the Internet goes down and the WAN2 port ip address says 0.0.0.0.I've tried releasing/ renewing and it still says 0.0.0.0.Everything else is set as the default.
View 1 Replies
View Related
Jul 16, 2011
I switched from Time Capsule with AirPort to E2000 and have a problem with configuration.I use the same IPs as in AirPort and E2000 gives me an error:"The WAN IP address cannot be the same subnet as the Guest Network IP address" and I can't save configuration.But in my opinion they are different.I use "Static IP" option and I have IPs from my ISP: [code] So WAN IP is different subnet as LAN and I don't know what to do now. It worked with these settings in AirPort and here I can't proceed.
View 2 Replies
View Related
Mar 2, 2013
I have a WRT54GS router, and starting today I am completely unable to access the internet through it. If I connect my computer directly to my modem, I can access the internet, but if I try to connect through the modem, all I get is "DNS server not responding".I've tried changing the DNS server address on the router configuration page, but it doesn't work.
Here's what my ipconfig /all shows:
C:Windowssystem32>ipconfig /all
Windows IP Configuration
Host Name . . . . . . . . . . . . : HomePCPrimary Dns Suffix . . . . . . . :Node Type . . . . . . . . . . . . : HybridIP Routing Enabled. . . . . . . . : NoWINS Proxy Enabled. . . . . . . . : No
[code]....
View 3 Replies
View Related
Sep 13, 2011
I currently have a LinkSys BEFSR81 connected to my cable modem as I need at least 6 wired ports for my house network. I also have a WRT54GS that is currently unused, but I would like to add it to the network so I can have some wireless connectivity as well.
Assuming that it's possible, what's the best way to combine these two units into the same network? Can the WRT54GS simply be connected downstream from the BEFSR81 via one of the open ports? I'm assuming that I'll have to change the IP address on the wireless unit to make it individually accessible for configuration, status checking, etc.
View 2 Replies
View Related
Oct 12, 2012
Is it possible to create a service which will forward public port 9010 to an internal IP address with port 23?First of all, I do not like to open the public Telnet port to the inside so I would use another public port and second my ISP does not allow some public ports beneath port 80?
View 1 Replies
View Related
Feb 28, 2013
The router stopped working for wired connections. I can still go online using my laptop via wifi, but when I connect a network cable to the laptop and turn off wi fi, connection does not work. Can't go online with a desktop with a wired connection to router.Everything else works via wi fi: iPad, android phone, tv with wifi.
View 1 Replies
View Related
Jun 3, 2012
I have been trying to clone my PC's MAC onto my Linksys WAG120N adsl2+ modem router .
I click the the clone my PC's MAC button in the MAC address clone tab. I get the following error :
"Mac address cannot be the multicast address"
The MAC address starts with 1C:C1:XX:XX:XX:XX
I even tried to update the firmware.
View 9 Replies
View Related
Jun 1, 2012
We have an ADSL connection and use a D-Link DSL-320B modem. We have a D-Link DIR-120 router connected to this modem. This has worked perfectly fine up until today when we disconnected the router and connected a computer (call it A) directly to the modem because it was getting an unusable connection through the router for some reason. We later also performed a factory reset on the DIR-120 router.
Unfortunately, after the above steps the router did not receive any IP address (through DHCP) from the ADSL connection anymore. During my attempts to debug this I noticed that my laptop (call it B) didn't get any IP address either (when connected directly to the modem). I noticed the following syslog entries repeating over and over while trying to connect: [code]
At this point computer A could still get a connection just fine tho (when connected directly to the modem).
I then tried to change the MAC address of the router to an arbitrary one (a copy of computer B's MAC address but with the last digit increased by one). The router still did not get assigned any IP address. Finally I tried making the router clone the MAC address of a third computer (call it C). C has never been connected directly to the modem. Doing this worked. After cloning the MAC address of computer C the router is immediately assigned an IP address and the internet connection works as it did prior to all this.
Now, my question is, why would computer B and the original MAC address of the router not be able to get an IP address while two other computers worked just fine? Why would changing to an arbitrary MAC address not work while cloning the MAC address of another computer did? Could the router's MAC address have been blocked by the ISP for some reason (and what could cause this)?
but my situation seems more like a blacklisting of some MAC addresses rather then allowing just a single MAC address.
View 1 Replies
View Related
Apr 26, 2011
On my cisco IOS 12.4 router,Can i make it so only lets say mac address 11:22:33:44:55:66 able to use ip address 10.10.10.2?I want this so that only this IP can configure servers, and so if the computer using it is turned off, any other device cannot use the IP address.
View 6 Replies
View Related
Dec 28, 2010
I just discovered that my wireless download speeds are 5Mbps, compared to 16Mbps if my laptop is connected directly to the modem or wired through the router. Uploads are 2Mbps either way. I have a WRT54GS v.6 with firmware version v1.52.8 which I updated today, completed by setting factory default through the router webpage after I discovered this discrepancy. The firmware update did not improve the download speed appreciably, if at all.Should the wireless connection be that much slower than the wired connection through the router? If not, what sort of issues could I be having to account for this?
I did just replace my modem when I discovered I was having erratic speedtests and that corrected that problem. That is when I became aware of the wireless issue, so not sure how long that has been the case. I have Charter's 16/2 HSI, living in a sparsely populated area with solid internet service. There is no external nor internal interference on this 2.4Ghz band.
View 8 Replies
View Related
Oct 29, 2011
My PC was working fine until yesterday. Now it keeps saying "acquiring new ip address". I have contacted provider and internet works fine, wireless laptop connects with no problem.
View 1 Replies
View Related
Mar 8, 2011
. The laptop can connect to the internet using the wifi card. However, it cannot connect to the internet when using the wired connection but it can be pinged from other machines at work. The NIC does not pick up a different IP address even after releasing and renewing the IP address through cmd. I have uninstalled and reinstalled the NIC. The NIC is working because when I set a static IP address the machine can connect to the net. Using DHCP it goes back to that same IP address. I have tried a winsock repair as well with no go, as well as taking the machine off the domain and re-joining it. Anyone see this before? Is there something I can do on my end to get a different IP address through DHCP or do I have to get a Network engineer involved? This is a machine on a corporate LAN.
View 3 Replies
View Related
Feb 19, 2013
Nothing seems to be able to connect to my wireless network. It seems to have occurred after I installed a new copy of windows 7 onto my sister's desktop. A message appeared saying we have the same ip address. I've tried renewing our ip address on both desktop but it won't give us new ip address for some reason.
View 14 Replies
View Related
Feb 25, 2011
I need to change the ip address on my router same ip address as myDlink router?
View 6 Replies
View Related
Dec 4, 2012
I setup a guest wired network on the WLC 5508 with 7.2.110. A postage machine can only be setup for static IP address over guest wired network. Is any one how to get it configure on the WLC 5508?
View 3 Replies
View Related
Apr 14, 2013
I have two ethernet cards (from same equipment) that arent acquiring IP Address after instalation of WLC 2504.I dont want (yet) to disable DHCP proxy on WLC.
*DHCP Socket Task: Apr 15 18:49:04.219: 00:0a:95:XX DHCP received op BOOTREQUEST (1) (len 556,vlan 0, port 1, encap 0xec00)
*DHCP Socket Task: Apr 15 18:49:04.219: 00:0a:95:XX DHCP dropping packet (no mscb) found - (giaddr 0.0.0.0, pktInfo->srcPort 68, op: 'BOOTREQUEST')
*DHCP Socket Task: Apr 15 18:49:07.218: 00:0a:95:XX DHCP received op BOOTREQUEST (1) (len 556,vlan 0, port 1, encap 0xec00)
*DHCP Socket Task: Apr 15 18:49:07.218: 00:0a:95:XX DHCP dropping packet (no mscb) found - (giaddr 0.0.0.0, pktInfo->srcPort 68, op: 'BOOTREQUEST')
[code].....
View 6 Replies
View Related
Mar 6, 2012
I am having an issue where occasionally the Sidewinder starts to see my internal RFC 1918 address instead of the configured external address of my firewall. This is for peering between the two. The error they see on the Sidewinder is:So instead of seeing the external peer address he sees a 10.220.3.18 address. We are not sure what triggers this becuase normally he see's my 63.117.98.222 address.
View 5 Replies
View Related
Jul 8, 2012
I have an old ASA 5505, and I'm having some trouble with Nat Hairpinning. I've done this with other firewalls before and I am having no luck now. I have an internal address that I wish to forward from an external address- so if someone goes to 123.456.789.012:3456 then it will forward to 192.168.1.244:92 (All numbers are arbitrary here- only for illustration). I have and Access Rule and NAT and PAT set up so that I can get in if I originate from outside the LAN. What I am trying to do is to have this work from inside the LAN as well- so that if I am at my desk, and I connect a device and type in 123.456.789.012:3456, it will deliver the content at 192.168.1.244:92. The problem I am having is that it just isn't working, and I cannot figure out why- When I started here, there was an address configured to work this way, and it still works- I just cannot find what is different between what I am doing and what the person who configured it did.
View 7 Replies
View Related
Oct 13, 2009
Is it possible using any module in CW to get the MAC address and IP address of all switchports on a 6500?
View 6 Replies
View Related
Aug 23, 2009
I recently switched routers to the DIR-615 and I'm trying to troubleshoot why one of our laptops keeps losing the IP address and gets a self-assigned IP address. I see the following messages in the log, I am wondering if the reason codes are listed and explained somewhere? I tried searching the manual but could not find any information.
View 9 Replies
View Related
Jan 3, 2013
Cannot connect to Linksys Router 192.168.1.1 Webpage. I am trying to access the IP address so I can secure my wireless router.
View 5 Replies
View Related
May 10, 2011
what would be the easiest way of blocking a mac address from LAN not wireless, the router is Linksys E2000 and the reason isnt important, just that i want to do it, i have full access to router
View 7 Replies
View Related
Dec 21, 2011
I have a 6 month old Cisco e-4200 router that is updated to the latest firmware, connected to a Motorola surfboard modem on Sudden-link in Midland, TX.
I previously used this exact same setup on Cox Cable in Wichita, KS with no problems. Upon setting it up down here I cannot get the router to pickup an IP address. I have Power-cycled everything multiple times, did a complete reset and re-installation of the router software and still no luck. The Sudden-link techs have no idea what is wrong. They said that the modems signal is strong and everything should be working.
Actually I did get it to work once for a couple of days, however when redoing the surround sound system I had to unhook the cable line and it quit working and I haven't gotten it to work again since. I have tried unhooking everything. Turning it all off. Waiting for 5+minutes, and then reconnecting in order: First the modem, then an ethernet cable to the computer which will usually work. But as soon as I unplug the cable from the computer and plug it into the router it stops working.
View 1 Replies
View Related
Apr 2, 2012
I have an e3000 that cannot obtain an address from the ISP. I can get an address on the computer and an old router by directly connecting the cable to the computer or the router. I can also daisy-chain the e3000 to the old router, and I can get an address on the e3000 from the old router. I have hard reset the e3000, changed firmware from the Linksys to TomatoUSB and back to Linksys, and I still can't get it to work. It worked fine on Saturday until a bolt of lightning hit close to the house. Since then, I cannot get the e3000 to connect to the ISP.
View 9 Replies
View Related
Feb 5, 2011
Last week suddenly my internet connection failed. I have tried several times to establish the wireless internet connection. Everytime when i tried to do this, i get the message 'can not get IP address'. Already tried to upgrade the firmware but still same message appears.
View 4 Replies
View Related
