what would be the easiest way of blocking a mac address from LAN not wireless, the router is Linksys E2000 and the reason isnt important, just that i want to do it, i have full access to router
View 7 RepliesIm using a linksys e 2000
Is there a way to block more than 4 websites, and 4 keywords?
currently using Linksys Cisco E2000 ,Firmware 1.0.04.Trying to few block sites from Access restriction - bellow is the screen shot its not working. I have alos enabled SPI Firewall from Security Tab. how could I block site successfully.
View 9 Replies View RelatedE2000 about a years old.One of the rule is to block internet access from 1am to 4am for certain internal IPs.Working fine until a week ago. Once the time kick in, the E2000 will not route any internet access for any internal IP until the unit is power off and power on reboot.If that rule is disabled. then the E2000 will route all days and nights with no problem.Updated firmware to 1.0.0.4 already.I replaced the WRT45 because of the same problem a year ago. Now just about a year, this E2000 keeps blocking all traffic.
View 1 Replies View RelatedI switched from Time Capsule with AirPort to E2000 and have a problem with configuration.I use the same IPs as in AirPort and E2000 gives me an error:"The WAN IP address cannot be the same subnet as the Guest Network IP address" and I can't save configuration.But in my opinion they are different.I use "Static IP" option and I have IPs from my ISP: [code] So WAN IP is different subnet as LAN and I don't know what to do now. It worked with these settings in AirPort and here I can't proceed.
View 2 Replies View RelatedI've been keeping an eye on my IPS report tab lately and have been watching a large number of ICMP_SMURF and DOS attacks originating from chinese ip address's. I know I can probably block the offending ip's through the ip based acl tab in the firewall settings, but I'm kind of a newbie how I can block certain ip's from touching my router?
View 3 Replies View Relatedi got an E4200 V2 and it is updated to Linksys Smart Wifi firmware.. Is it possible to block a specific public IP address?
View 4 Replies View RelatedI have an EA4500. I am trying to block a specific site based on keywords in the webpage address. how to get the EA4500 to block sites with based on keywords.
View 1 Replies View RelatedI have been looking into this router, I would like to know if I can enable Parental controls or access restrictions to block a MAC or IP address; from 03:00 AM - 06:00 AM ?Instead of Midnight to 6:00 am.My E4200 works just fine, Just would like to know if the EA6500 Can do that ?
View 7 Replies View RelatedI have a WAG160Nv2 and I want to block specific external ip addresses from trying to get at our server that uses the WAG160Nv2 as an internet gateway. It's not immediately obvious if this can be done from looking through the config pages.
View 4 Replies View RelatedI can connect to my router but either way it seems like i can't get any internet access (both wireless and by cable): url...I have tried the steps that the linksys FAQ suggests shall fix this problem, but this has not worked. I have also tried to reset the router without any luck. I know it its not the modem that is causing the problem because I'm wired to it now.On the E2000 every light is blinking as it should be (hence the FAQ) so it indicates that there might be a problem with the connection between the router and the computer (tested on other computers too without success).
View 9 Replies View RelatedI need to get my tablet set uo with Linksys E2000 router
View 1 Replies View RelatedAbout a month ago I set up FTP on my QNap for the first time. To my surprise I was able to connect to it from an outside network with no further configuration needed. Since then I have had a bit of an issue with firmware. I ended up wiping and upgrading the QNap. Since then I am unable to connect. Some resources are saying the only problem is that I don't have port forwarding set up. I guess my default router settings were already set up to forward the port (I'm not sure how to confirm) because it worked originally, the only thing that changed is my QNap settings. I would like to be able to use it as a FTP, MySQL database, and a few other things. Will I have to do a different configuration for each one?
My network set up is like this: Verizon Router/Modem -> Linksys Router e2000 -> Qnap (ethernet)
I accessed my verizon router and under port forwarding it says "Protocol: FTP, Ports: TCP Any -> 21". NAT is disabled on the Linksys so does that mean I won't have to configure it at all because it is set up in bridged mode as a dummy switch?
What IP should I be using to try to access it remotely?
When I try to connect to my QNap IP I get this in Filezilla:
Status:Connecting to 192.168.1.22:21...
Status:Connection established, waiting for welcome message...
[Code].....
How can i use Linksys E2000 rounter as a Access point ?
View 1 Replies View RelatedCan i move my linksys e2000 router to a new computer and if so how do i go about it
View 2 Replies View RelatedI would like to set the router's dns entries but I don't see how to do that. Basic setup page has DNS setep for the DHCP scope but I don't want to push dns to my pc's. What I am looking to do is to use an alternate dns to what my service provder pushes and still have the abliity to route on my internal network.
View 1 Replies View RelatedWe bought our Linksys E2000 in the summer and went to set it up but something came up... Now we are trying to set it up but cannot find our WPA key... Where can we find this?
View 2 Replies View RelatedSo i can only forward 10 ports on my E2000.Example, one game (Battlefield 3) requires 10 ports (TCP and UDP combined).What about my other games? how can one, if possible, add more ports to the router?
View 4 Replies View RelatedE2000. I run the setup program, my laptop sees the router and it shows a strong signal. When I try to connect with it, it won't connect.
View 9 Replies View RelatedI've been looking around like a madman now in the settings. where can I turn off my WPS ? Just cracked my own PIN within 6 hours with Reaver.
View 9 Replies View RelatedMy internet cut out last week and after calling my ISP I found out it was in fact my router that was causing the problem (regular connection to PPOE works fine). I've only had my E2000 about 2-3 months and have not had any problems with it. I've restarted the router, done a factory reset, upgraded the firmware, renewed the IP and still I cannot get any connectivity. I can access the router UI fine and I get a response from pinging it and also I have tried replacing the cables but that didn't fix the problem either.
View 9 Replies View RelatedI have an E2000 that I was given as a gift. I would like to use at it my office for a switch at my cubicle where I can connect 2-3 computers simultaneously. I am in a large network and am a user only. When I hooked the E2000 up today my computers would not get internet access BUT my laptop got wireless access and internet.
View 2 Replies View RelatedI'm using E2000 currently and meet a wireless connection problem. The speed can up to 300M bps. When I confiured the E2000 to band auto (20-40mhz) and my wireless network card to work at also auto (20-40) mode, it always down to 144M speed when connection.
If I changed some settings in E2000's wireless configuration, in the status sheet I can see it works at 40MHZ. But after a while,(5-10 mins) it automaticly down to 20MHZ and my labtop connect only got a 144M speed.
how can I deal with that to make it always keep at 300M connection? Note the previous router I used to connect to my lattop can always keep that speed.
I want to block a computer by its MAC address, not by IP, from accessing Internet.
View 1 Replies View RelatedI have blocked a hacker from hacking my pc, I tracked his IP and then blocked it.
View 1 Replies View RelatedI currently have my wired cable internet hooked into my wrt310n. I have that hooked into a linksys 10/100 ef3124 switch. From there, I have cat5 run to the back of my house, where the wireless signal is weakest. I've got an E2000 router and would like to hook that in at the back of the house. What settings do I need to make in order to set up a completely new wireless network in the back of the house?
View 1 Replies View RelatedI have an e2000 wireless router. I have the latest software version for the Cisco software.I have noticed that Cisco sets up the same password to access the router setup page as the wireless password..Anyone that connects to the main SSID will be able to connect to the setup page at 192.168.1.1...I know that I can change the password in the linksys setup page to whatever I want, but then when I open the Cisco software, it wants me to change the password to match what the administrator password is.Don't they realize that a wireless password is different than the Administrator password to access the router settings?
View 5 Replies View RelatedMy internet is hooked via cat6 ethernet cable to my Cisco/linksys E2000 Router.Sometimes the net works fine, and there are no problems. Other times, after 10 minutes or so after booting up, net pages stop loading. The small yellow exclamation mark appears, and every time I run the troubleshooter, the same info comes back to me - DNS server is not responding. Until I restart again the internet wont work, but on occasion things seems to fix themselves and continue working until I shut down.This problem never happened before i moved back home. In my previous apartment we had comcast cable and it ran without a hitch. Since I have been home this DNS problem has persisted, but only on my computer. I run the only windows PC in the house - my family is mac happyThings I have trie - I have tried "netsh winsock reset" in the command prompt, I have run virus and spyware scans several times over, Have reset the modem, router, and the Mac which hosts my 'home network'-come to think of it, I haven't tried reinstalling my LAN driver, but that seems insignificant b/c it has never once had problems.
View 8 Replies View RelatedI am trying to connect my Linksys E2000 router to my French Sagem modem but the connection is not compatible. Can I buy a cable which is compatible with the connection on a French modem
View 1 Replies View Relatedi bought a Linksys E2000 router. When i went to set it up, i noticed that the old router has a phone line connected to it. When i looked at my E2000, I noticed that it didn't have a phone port in it (Rj11). Not sure what to do. Would it be possible to buy a Rj11 to Rj45 converter and just use that to connect the phone line to my router?
View 1 Replies View RelatedI have a E2000 router that would go out and I would have to unplug and replug in every once in a while. Finally it just stopped working completely. I reset the router and now it won't let me connect. I have followed advice given to soembody else on here and went into router settings and cloned the mac, the IP address was there and reset my security settings. It let me connect to the network but not the internet...
View 2 Replies View RelatedI have a Linksys E2000.
It worked fine until one day, without any change at all, it simply stoped working. I mean, I can still connect through my wifi laptop connection (it shows connected to my router and says that I have an excelent signal). But, I can't reach the internet. But, If I unplug the internet cable, and plug it in my laptop, the connection works fine. A friend told me that this could be caused intentionally by the internet provider, that they would block my signal to avoid me using a wireless router, trying to force consumers to sign their own wireless service. Thus, by this friend advice, I've cloned my laptop's MAC address to the router. It didn't work either.
I have a Cisco E2000. When i connect to my cable modem directly, I get 30-35 MBps down and about 10 up. When I plug in to my E2000 it does that at first... but slowly over time, the speed degrades, usually down to about 5-6 down and 3-4 up. If I unplug the router, it typically restores full speed, but not for long (a few days maybe). Also, when I unplug the router, it is pretty hot.
View 4 Replies View Related