i need to add a lot of mac addresses in mac addr filter table. many routers do not allow me to add a note for each mac address. that makes management a bit difficult.
eg.
field 1, field 2, enable
xx:xx:xx:xx:xx:xx , peter pc, y
xx:xx:xx:xx:xx:xx, mary pc, n
I know that very few people have their wireless controllers on version 7.4.100. But has any one noticed that the NAT IP address field in the management interface configuration menu is missing?, although it is mentioned as being present in the WLC 7.4 configuration guide. This would definitely affect Office-Extend.
View 4 Replies View RelatedI have added all of the devices to DCR and they show up with their hostname value in all of the device trees except for the fault manager views. In all of the fault manager views the hostname is not being used for the Devie Name field, rather the IP address is being used.
View 6 Replies View RelatedI have hw-550-3G modem and I like to know how to setup Mac, IP filter.To allow only the Mac, address in the list using the internet.
View 3 Replies View RelatedUsing ACS 5.2, under Network Resources>Network Devices and AAA Clients>, I can only filter by:
Name
NDG:Location
NDG:Device Type
Description
How can I find a device by its IP Address? or how can I enable this option?
On this link:[URL] I read the following: ''Network Device Filters—Based on the AAA client that processes the request. A network device can be identified by its IP address, by the device name that is defined in the network device repository, or by the NDG'.....
How could I do this on my ACS server?
Im using my upstairs neighbors wifi with permission. It has no protection whatsoever but recently i havent been able to use it anymore, and they both just went on vacation yesterday. Their dad was there for a day or two before they all left, my assumption is he thought i didnt have permission and did something to prevent me from connecting without mentioning it before they left.Its full bars (its directly above me) but the router almost instantly doesn't respond when i try to connect. Did he mac filter my wireless adapters adress? I tried changing my mac address on my wireless adapter (aka, desktop, as it doesn't have a nic) but Tmac cant change it successfully. Tmac is able to change my laptops mac though, but even after doing so i still cant connect to the network.
Other issue - right now im using a crappy 2 bar connection called ddrtvap on my laptop. The laptop sitting right where my wireless adapter for the desktop would be and it connects fine, but my desktop cant connect to this network (it connects to the network, but no internet) while the laptop does just fine. Windows repair is super usefull as it tells me something is wrong with my adapters settings but gives no clue as to what.
I installed the 2.06NA on my DIR-655 router and now I'm having problems adding mac addresses to the network filter. The message is "Invalid MAC address". Of course, it doesn't tell me which entry is invalid and I have a number of them. After further checking.. I noticed that one of the MAC addresses is indeed invalid and when I remove it I still get the error message?
View 1 Replies View RelatedI had no problem running both 2.4 and 5.0 Bandwidth. With WiFi password and without. It does it's job. The 2.4Ghz Range Plus works. I have set up the router on the 2nd floor at the highest it can go. And everyone get's full bars all over the house. I even get 4-5 bars outside in my car on my phone.
The only issue I have with this thing is a damn new netbook I got for Christmas with a Mac Address starting with 0C-EE-E6-XX-XX-XX. The Router finds the Mac Address invalid. In which I can come to understand cause seeing a Mac Address starting like that is completely new to me. Every Mac Address I have, started with 00 except the netbook. So now, I spent days trying to find firmware updates, patches, anything! I even attempted to spoof the Mac Address on the netbook but Microsoft has a bug on Windows 7. (I have the Starter Edition that came with the netbook)
Windows 7 Mac Spoofing works with WIRED Connection. But it does not work with WIRELESS Connection. I used 3rd Party Tools: SMAC and etc... I attempted Registry Edits, I changed even the value key to the "Orginal Mac Address" and it just wont change [New Strings/Network Address Edits included]. I have been banging my head about this for a week now. The Internets has many answers but they did not work. So Spoofing the Mac Address is out of the question. Until Microsoft fixes this bug.
Anyway: Did D-Link release any sort of beta update/driver/firmware or anything to resolve this at all? Is there a modded firmware to force the Router to take this stupid paradox of a Mac Address?
Currently: I have the Router's WiFi Password-ed with Default Factory Settings
{Hardware Version: B1
Firmware Version: 2.02NA}.
I am using an ASA 5510 firewall in routed mode.How can I filter incoming traffic by mac address on the AS 5510 ? I have already setup a static access rule for rdp users on the outside to access a terminal server on the inside.Now, i would like to further limit access from specific computers only.
View 7 Replies View RelatedI tried to configure my wifi router recently to secure my internet connection. I wanted to add a MAC adress filter, but I had to leave before I could enter them all. I thought that I wouldn't have to enter my own MAC adress since I'm directly connected to the router with a wire, but it looks like I should have entered my MAC adress, because now I can't get access to my router by typing the IP adress, as usual. I tried to reset it, but it doesn't work.
View 2 Replies View RelatedI have a Linksys WRT54G router.I am trying to set up my internet connection so only my approved MAC Addresses can connect.I set everything up. I purposely excluded my laptop from the list to see if I did it right and I guess I didn't because my laptop is still able to connect to my network.
View 7 Replies View RelatedI want to add more than 40 mac address filter into my WRT54GL with firm version V4.30.7 but the form to enter the mac address list just limited to 40 mac address register. How do I can add more than 40 mac address list in my WRT54GL ? perhaps we can add the list into WRT54GL like XML file or somehow that can make me add more than 40 mac address register list.
View 2 Replies View RelatedIs it possible to configure cisco router like C3800 or catalyst switches like C4500 or C2960 to filter traffic based on allowable mac addresses only? I would like only to allow those devices that belongs to the domain, meaning if a user connects a computer or any devices that concerns network which I have not allowed the mac addresses, it will be denied access to the network. However, any of the allowable devices could able to use any port of the switch, meaning I dont want to associate an allowable Mac Address to a physical port on the switch.
View 2 Replies View RelatedWe have a wifi router RV220W and we need to filter the mac address. The problem is that the number of the "allowed" devices is around 50 (not all connected at the same time), but the maximum number of mac address which can be listed in this router for each VLAN is 20, so for the moment we set 3 VLAN, each one with a different mac adderss list. This is very awkward because the area to be covered by the wifi network is large and we need repeaters, but having 3 VLAN we should put 3 repeaters for each point. Is there any way to configure this router in order to have a single VLAN but with a mac address filter list of 3 x 20 mac address?
View 1 Replies View RelatedI have gone through the data sheet of WAP4410N,bu have got nothing about the scalability of MAC address filter on WAP4410N?
View 1 Replies View RelatedHow does a firewall block or filter traffic on a specific port or IP address?
View 1 Replies View RelatedThe wireless client can't get the DHCP address when I enable the On-MAC-Filter-failure, MAC Filtering and Web Auth. Client can get the DHCP address when I only enable the Web Auth in the same WLAN SSID. The WiSM verion is v7.0.235.0. [code]
View 1 Replies View RelatedUsing Cisco ASA5510 Security Plus (Post May 2010) with 8.2(1)
I was trying to limit the number of internet IP Address that can initiate Remote Access VPN connection to the firewall. I have plan to only allow internet IP Address from few ISPs for control.
However, blocking AHP, ESP, ISAKMP, NON500-ISAKMP, and IPSec Over TCP Port Assigned in the firewall outside interface doesn't work. But it works by putting the ACL in the router before the firewall. It seems that the firewall have a "hidden" process VPN first before user entered ACL (or explicit rule), similar to Checkpoint FW's implied rule. How to get around it?
We want to filter IP traffic by MAC address on Catalyst 4500. Since we are using bonding (active-backup mode) we need those mac addresses appear on different ports. Below are solutions that we have tried: ACL but it does not work since mac acls only match non ip traffic (We CAN NOT use ip acl). Use a static mac address-table entry to ALLOW specific mac addresses. It does not work either since the same MAC address needs to be seen on a different port. Catalyst 4500 does not support auto-learn option (as e.g. Nexus 5000).
View 3 Replies View RelatedI have noticed that changes in MAC address filter list are applied only after reboot of router. It is inconvenient.
Router Linksys E4200
Firmware Version: 1.0.03
Operation system on client computer is Windows 7.Can it be resolved in the next version of firmware?
The note 2 can connect with the router if I have the router set to open but when I change the security to anything else it keeps re-authenticating and will not connect.
Have only been using the wired before and it works great but now need to connect note 2 to do backups. I have even tried resetting the router back to factory settings and turning on WiFi again and no luck.
Samsung will be releasing the Galaxy Note 8 sometime in the second quarter of this year.
I have an Amazon Prime Account and would like to know if I can transfer the downloaded movies I purchase on Amazon on the Galaxy Note 8.
I have Windows 8 installed on my computer at home.
I have an N1 Wireless Router (F5D8231-4 ver 2). It is setup with WPA/WPA2-PSK on and links to a Windows Laptop and an iPod Touch perfectly. I cannot get my new Samsung Note 10.1 (GT-N8000) connected. I have tried changing the router to WEP 128bit and even no security. The Samsung links perfectly to my neighbours Thomson Wireless Modem/router with no security. The Belkin N1 is recognising the android trying to link and assigns an IP. The Samsung instantly sees the Belkin network ( says " very strong signal") & tries to connect. It saves the network but gets stuck trying to obtain an IP address & reports "network disabled" and "weak signal".
View 1 Replies View RelatedI have a Belkin N Wireless Router Model F5D8236-4 V2. WEP security.. We have just bought a Samsung Note 10.1 Tablet. We have entered the password Key and the tablet is saying that the network is 'secured,saved' but it will not connect to the internet. We have several laptops and phones that work ok but the Samsung Note will not connect.. We have taken the Note to a friends house and it connects to the internet no problem so I know issue is with the router..
View 3 Replies View RelatedI have a number of devices in my house connecting without issues:
1.) PS3
2.) XBox 360
3.) HP CM1415FNW
4.) Sony Dash
5.) iPone 4g/4gs
6.) Asus EP121
7.) Six Laptops
8.) TV
9.) Denon A/V
My android cant even pickup the SSIDs, I stand beside and still nothing, the SSIDs are not hidden, Ive tried different encryptions, changed from AES to TKIP, tried different channels. I have two seperate SSIDs, one 2.4GHz with B/G/N and a 5.0 with A/N Available, neither SSID is getting picked up
The URL field in the web access log has a length of 70 characters. Is there any way to increase is[INFO] Mon Jun 13 21:30:30 2011 Website1234567890012345678900123456789001234567890012345678900123456789001234567890 accessed from 192.168.xx.xx
View 2 Replies View Relatedusers whose status is manually disabled don not have difficulty in authenticating and access managing nework devices. that makes me wonder what is the difference between status enabled and disabled?
View 44 Replies View RelatedI'm running VPN SSL on an asa 5520 (V8.2.5) with LDAP authentication and everything works fine but now the AD people changed name in the groups and they added a " " "blank" in one of the fields so when I configured the group I get an error.
for example:
map-value memberOf CN=VPN_SSL_ABC,OU=External,OU=XXX,DC=ext,DC=local ABCPolicy
but this does not:
map-value memberOf CN=VPN_SSL_ABC,OU=External Group,OU=XXX,DC=ext,DC=local ABCPolicy
Is there any way to insert a space in the OU field?
Does anyone know of some off the shelf (commercially available) software that will set the DSCP field to something other than 0? Im looking to do some network testing using any off the shelf software, voip, games, whatever. I have already setup a traffic generator but my testing needs to encounter a more real life scenario. I have already tried many games, skype, gchat, etc. but nothing sets the DSCP field to anything other than 0.
View 4 Replies View RelatedI did not know the username and password for my DI-524 so I wanted to do a reset...used a paper clip and held the reset button for ten seconds, unplugged it, powered it up, and as per online instructions tried to type in 192.168.0.1 to access the username and password field so that I could enter "admin" and blank password. Here's where my lack of knowledge comes in. I am working off a MacBook with no Ethernet connection, just wifi. Is what I am trying to do even possible? Or does the computer I configure the router with have to be hardwired to the Internet while I do it?
View 1 Replies View Relatedbetween fields in import template file (add or update) for internal users is no column for expiration date ([URL]). This field is not defined also for export file.
My question is: (How) is it possible import new users (or update existing) into internal db with expiration date field?
I have upgraded my new WLC to version 7.0.98.218. I noticed the N/A for the Field recovery version. On my old 4402 it is called the Emergency Image Version, and it is 5.2.157.0
How do i get a recovery version on the WLC?
We currently have a distributed PR and DR ACS 5.3 setup, set up with tacacs devices and one radius device.The radius device is used Opnet's AppResponse Xpert Admin. We are trying to intergrate AppResponse Xpert Admin with ACS.
The GUI for AppResponse Xpert Admin is asking for the radius server ip address - i.e our ACS , radius port - i.e 1812 and "secret" - I'm guessing this means the shared secret of the actual ACS itself (not the shared secret used by network devices) .
On our ACS 4.2 systems we have a field for a shared secret regarding the ACS server itself (to authorise replication?).
Using the search function for "Shared Secret" in pdf "User Guide for Cisco Secure Access Conrol System 5.3" has only found references to setting one for network devices and not a field for the ACS itself.Is a ACS server shared secret still relevant for the ACS 5.x system?