I have added all of the devices to DCR and they show up with their hostname value in all of the device trees except for the fault manager views. In all of the fault manager views the hostname is not being used for the Devie Name field, rather the IP address is being used.
View 6 RepliesI just got a DIR-655 and set it all up pretty easily. I have 6 wired and 3 wireless. All work fine and all are set to use DHCP. But if I go (in the router) to the Lan Computers list under Device Info, three devices (2 wired, 1 wireless) do not appear. I do have a switch added to the system, but of the three devices connected to it, 1 shows in th Lan Computers list and the other 2 do not.Since everything works, I'm mostly just curious why this is. Every previous router I've had showed everything correctly.
View 3 Replies View RelatedI know that very few people have their wireless controllers on version 7.4.100. But has any one noticed that the NAT IP address field in the management interface configuration menu is missing?, although it is mentioned as being present in the WLC 7.4 configuration guide. This would definitely affect Office-Extend.
View 4 Replies View Relatedi need to add a lot of mac addresses in mac addr filter table. many routers do not allow me to add a note for each mac address. that makes management a bit difficult.
eg.
field 1, field 2, enable
xx:xx:xx:xx:xx:xx , peter pc, y
xx:xx:xx:xx:xx:xx, mary pc, n
I any running Cisco Works LMS 4.0 on Windows 2008 Enterperise Edition with SP2.I am facing 2 issue which are below:
1. Get message "You are using unsupported Version". As per Cisco document Windows 2008 Ent edition is support by LMS 4.0
2. All of my devices are showing unreachable. I already double check the Devices Credential include SNMP (Read and Write community) and Username and passwords.I can accessble all devices via telnet from the same Cisco Works Machine.
I have discovered my switches in LMS but it is showing unreachable what can be the reason ?
View 5 Replies View RelatedMy DFM is showing 40 devices in the "Questioned" State. Lots of them are 3750 switches and 2801 routers. It has "Known" a few of the 3750s and 2800s, but most of them are Questioned. How do I go about troubleshooting this? It's
DFM 3.2.0, part of LMS 3.2;
I tried to reinitalize the DFM database, but that caused all sorts of other issues like my ANIServer not running anymore etc. I have a ticket open with TAC for that issue though.
We had an existing installation of LMS 4.1 which seemed to have worked fine with the exception that it was giving problems with logging Syslog events. We tried everything to resolve it and then we found a link on this very site that explained that there was a bug in displaying Syslog events on LMS 4.1. It is important to state that we would get a few Syslog events but the rest were either filtered or discarded.As per the bug toolkit, we realized that we had to upgrade to LMS 4.2 to have the bug resolved. This was not a problem and we installed LMS 4.2 as a direct upgrade to LMS 4.1. We backed up our existing data and the installation process migrated everythin automatically.Now, LMS 4.2 is installed and our objective of having Syslog messages are being received regularly as we wanted.unfortunately, when we try to generate a report such as "Detailed Device" report and try to select All Devices from the Device Selector menu, we do not see any of our devices. However, we do find our devices listed under User-Defined Groups -> (Our DCR). Based on this, we can generate reports and everything is fine.Yet, we are doing this for a client of ours and they expect to see these devices listed in the "All Devices" section of the device selector. Apart from that, everything seems to be working fine.
View 2 Replies View RelatedA particular & ungreatful person abused my laptop to the point where I had to install a password. I had to perform all kinda of removal actions but I just noticed in my network domain that his name followed by "PC" & under "media devices" & "network infrastructure" contains his name again w/ PC & devices called [TV]UNE40ES6100.I am using the program's wireless service which I am allowed-to. I just want to remove this person from my laptop. It won't delete when r. clicking. I have win 7 and use this laptop mainly for my online school & email.
View 9 Replies View RelatedWe are using Campus Manager 5.2 with LMS 3.2. We have 100 devices and all 100 devices has been successfully discovered in Common services in all 100 devices are showing in DCR.When we check in RME we have found all 100 devices over there.
But, in Campus Manager we got only 95 devices. out of 88 WS-C2960G-24TC-L 5 switches are not showing in Campus manager. we have added the same manully ( manually included & Ecluded all 5 devices in Campus manager) and start the data collection, but no result.
After data collection it is showing not managed by Campus Manager when we check ( Show all Included devices option).
I noticed a TON of random devices showing up in my Network within Windows 7. When I say a ton, I mean 739! I am not computer illiterate, but definitely not a pro. My router is WEP password protected, so I'm not sure on earth is going on here. I thought maybe I had a torrent program open that could be affecting this somehow, but I don't..
View 6 Replies View RelatedI'm using the EA4500 router with Cisco Cloud Connect. I've noticed under Devices I'll see devices named "Network Device". They have a generic MAC address with something like "00:00:00:00:2F". They will have an IP that's already assigned to another device.
View 9 Replies View Relatedmy intel inspiron N5010 not showing any wireless devices.
gave a link to download the whole driver pack.
I have a case for an LMS 4.0 running in a Live environement (With devices already discovered and organized into seperate groups), where the Device Credential and repository DCR is showing suddenly as empty and only i can see the groups listed, but without any devices in them (Through Inventory > Device Administration > Add/Import/Manage Devices).After a restart of the whole LMS server a few weeks ago, the problem was fixed and the devices appeared again, but now the same issue re-appeared.
View 5 Replies View RelatedMy wireless has just gone it is not recognized in the device manager and a USB Device not Recognized pop up is showing up.i restart it a couple of times and once it did showed up but after i did it again it was gone again.i have a Toshiba laptop l300
View 3 Replies View RelatedNo network adapter showing in device manager
View 2 Replies View Relatedi've just upgraded my graphic card and now i don't have any network adapters listed in the device manager (only firewire under +IEEE 1394 and all the other devices) I've already reinstalled Windows 7 (64 Bit) and tried installing another LAN card (10/100) - that wasn't recognized.
Within the BIOS (award- Motherboard- GA-P35-DS4 ) i couldn't find anything related that should be turned off/on? [URL]
Could it be broken if it is not appearing there? If yes- why isn't the motherboard recognizing my other LAN Adapter that i've installed on the bottom slot
Should i reset the Bios by pulling the battery/using the cmos jumper?
I recently ordered and received Cisco Catalyst 3560-CG Series 8-port PoE switches (ws-C3560CG-8PC-S). In running the Cisco Network Assistant (Version 5.6(3)) they show up as an unsupported device. The documentation for this product indicates that you can use CNA to configure this switch. Is there a download or patch available to correct this problem?
View 8 Replies View RelatedIn asus router model rt-n10, there is a client list when you bring up 192.168.1.1 showing names of devices also mac addresses and ip addresses. How do I add names to the list so I know which devices are using what ip etc. I have tried the advanced settings in the router to see if I can do it this way , but no luck.
View 1 Replies View Relatedafter installing xp my wireless card doesnt show in device manager
View 8 Replies View RelatedMy Ethernet is not showing up in device manager or Network Connections. I've checked the bios and it is enabled. I've also tried to install the drivers, but at the end of the install this error message pops up " the Realtek Network Controller was not found. If Deep sleep mode is enabled please plug the cable"
View 1 Replies View RelatedI'm trying to install my WMP600N wireless adapter. It's not showing up in my device manager. The thing is I've installed it in the past and ran into some driver issue which made me give up. But it showed up in device manager before so I know it's not a dead card. Right now, plug and play isn't working. How do I get a Wireless Connection to show up in my device manager? This is for my PC. I also have a couple drivers I could use but I don't know how to install them because they are not exe files. I can't select upgrade drivers because the network adapter isn't showing up in the first place.
I have tried unplugging and replugging, and also scanning for hardware changes in device manager.
I have an EA4500 and am using Cisco Connect Cloud software. Its working mostly fine except that I have one device on the network that will not show up in the device list. This is not an issue in itself and normally I would ignore (although it used to show up when I forst got the router) however..
The device is a WDTVLive media unit and required access to windows shares on a media server. Now the WDTVLive device is server an ip address by the router and is available from everywhere on my network but every couple of days it loses the capacity to search windows shares.
I know what you are thinking and I initially thought the same, this is an issue with the WDTVLive box. However one day I spent a few hours trying to resolve (Am an IT Consultant and know a little about networks) and found that I could not fix the issue. I then rebooted the router and it started working. I have since confirmed that every time it breaks I have to reboot the router.
I am having vastro 460 with intel i3 and window 7 32 bit . try to install driver for network card but not working. ping is working but not showing it in device manger.
View 5 Replies View RelatedI recently formated my dell xps l502 system and installed with windows 7 Os.after that my Lan and Wifi are not working.when i did the ip config /all.it is showing only the following options.
-HPrimary DNS suffix :
-NodeTYpe: Hybrid
-IP Routing enabled :no
-WInsx Proxy Enabled : no
I have an acer M5641 desktop and i do not have a network adapter , i reinatall windows 7 basic premium and no success
View 1 Replies View RelatedExperienced problems with guest network not showing up as an available network on a device (laptop, iPad, etc)?I double checked if guest network is enabled on a EA3500 router. What other steps can I take?
View 5 Replies View RelatedI have the WRT400N router with the latest firmware. Recently I have noticed a device in my DHCP that I do not recognize. It is not device I own (believe me, I have racked my brain and confirmed) as it shows as an Acer pc. I cannot ping the IP address however. I have rebooted my router several times thinking maybe it's a former connected device but saved in memory but it keeps coming back. I am thinking possibly it is someone hi-jacking my Internet, but not sure. I am using WEP security but it shows a LAN connection which is strange for a wireless device. The only hard wired pc is my HP.
View 3 Replies View RelatedI have a WAP54g set up as a repeater. It even shows in the WRT54g device list (Tomato firmware) as a WDS interface but nothing can connect to it. I have the repeater's MAC address in the AP and it's set to "Access Point + WDS" mode. I don't know what I could be doing wrong. Is it a conflict of DHCP on the AP vs static on the repeater?
View 1 Replies View RelatedI am using Dell Inspiron N4010 for more than a year now. It was running good. At office i am using wi -fi and at home i was using through cable connection. Fer last few days my wired connection was not working and i got all cable checked and replaced, but could not solve the problem. Then i found that in device manager, network adapters, its not showing and wired adapter. Only wi-fi and blue tooth adapters are there. I can still connect to internet at office via wi fi but its not working at home now with wired connection.I am not able to understand how it stops working and why its not showing in device manage (Network adapters).Yes one more thing i want to disclose is that earlier i have only one drive i.e. c drive wich few days back i compressed and created another drive.
View 4 Replies View RelatedNot able to see devices in CS device management (0 devices).but devices are visible in other modules like RME and DFM.
View 3 Replies View RelatedI upgraded to firmware version 1.0.03 I started to have this weird issue: I have four PCs connected to this wireless router via wireless G. They all run Windows 7 Home Premium. After a few hours I started to notice that the DHCP client table is empty even if all four PCs are connected to the internet. This causes a networking problem because one of the PC serves as a file server and it grants access by IP addresses. Not being able to "see" those computers, my access is denied.
View 2 Replies View RelatedI am working with LMS 4.1 and FDM 4.1.0.
If I ask to the Supported Device Finder Portlet about C4503-E (SysObjectId: 1.3.6.1.4.1.9.1.874), it tells that this device is supported by DFM 4.1.0. Nevertheless, in DFM module each one devices appear in the "All Unknown Devices" group, with Error Code: Unsupported. CDP is enable in each one of these devices.