Cisco :: Devices Not Showing In Section Of LMS 4.2 Reports?
Jun 9, 2013
We had an existing installation of LMS 4.1 which seemed to have worked fine with the exception that it was giving problems with logging Syslog events. We tried everything to resolve it and then we found a link on this very site that explained that there was a bug in displaying Syslog events on LMS 4.1. It is important to state that we would get a few Syslog events but the rest were either filtered or discarded.As per the bug toolkit, we realized that we had to upgrade to LMS 4.2 to have the bug resolved. This was not a problem and we installed LMS 4.2 as a direct upgrade to LMS 4.1. We backed up our existing data and the installation process migrated everythin automatically.Now, LMS 4.2 is installed and our objective of having Syslog messages are being received regularly as we wanted.unfortunately, when we try to generate a report such as "Detailed Device" report and try to select All Devices from the Device Selector menu, we do not see any of our devices. However, we do find our devices listed under User-Defined Groups -> (Our DCR). Based on this, we can generate reports and everything is fine.Yet, we are doing this for a client of ours and they expect to see these devices listed in the "All Devices" section of the device selector. Apart from that, everything seems to be working fine.
View 2 Replies
ADVERTISEMENT
Aug 9, 2011
Have a problem with LMS 4.0.1 and DFM. In DFM no of the devices leaves the questioned state. Trying to rediscover them starts a process that ends after 20% completion every time. I've put on some debuging, but that does not enable more error messages.Only thing i find is in the log file [code] As I've encoded this to be the SNMP engine ID, which on the device is. [code]
View 4 Replies
View Related
Aug 8, 2012
When a tacacs user is changing the local password on the router (for local user), the acs 5.3 is showing the new password in clear text in authorization reports/logs.
This behaviour is seen on acs 5.x, whereas acs 4.2 is showing encrypted password in the reports.
I have checked debugs on Router and it is sending password in clear text in Tacacs Authorization packet but encrypted password in Tacacs Accounting logs.
Debug tacacs accounting
debug aaa accounting
4w3d: TPLUS: Received accounting response with status PASS
[Code]....
View 8 Replies
View Related
Jun 14, 2012
i have a problem that i see the devices by ip not hostname in devices report and topology and i checked in device discovery to appear by hostname
View 2 Replies
View Related
Oct 31, 2011
we have a 4510r-e running 12.2(50)SG1 w/ various rj45 line cards and a 24 port glc card.at any given time, i see 10's of ports in 10/full.i go to the station, and find the station in 100/full or 1000/full.
i go to the switch w/ my fluke, connect it directly to the switch w/o any intermediate infrastructure except a 50cm cat6 patch cable.the fluke reports 1000/full, but THE SWITCH PORT REPORTS STILL 10/FULL.all ports are config'd 'speed auto' and 'duplex auto'.
the switch seems to be erroneously reporting 10/full.there are no errors logged on any of the ports and there is successful communications even when the station and switch port report different speeds.even though there are no errors logged nor reported by 'show int [port]' nor 'sho int count error' certain killer applications crash on some stations. (the applications are GHOST (which dumps disk images from a server to multiple stations) and NETOP (which i sused in a classroom to transmit an instructors screen to a room full of stations) both of which broadcast and/or multicast.all nodes involved in the above 2 applics are on the same vlan and same phyiscal subnet.
the ports which report 10/full vary and occur even when the above applics are not in use.the only way i found to clear this 10/full report is by either a hardware reset of the entire module or by unplugging the cable, the execute on the port shutdown, speed auto, no shutdown, reconnect cable.then it's just a matter of time until it pops back to 10/full in a few minutes,hours or days.
how to address the killer applic problems besides restructuring the whole net by defining separate vlan for each lab of 20 or so stations?
View 7 Replies
View Related
Aug 20, 2011
I any running Cisco Works LMS 4.0 on Windows 2008 Enterperise Edition with SP2.I am facing 2 issue which are below:
1. Get message "You are using unsupported Version". As per Cisco document Windows 2008 Ent edition is support by LMS 4.0
2. All of my devices are showing unreachable. I already double check the Devices Credential include SNMP (Read and Write community) and Username and passwords.I can accessble all devices via telnet from the same Cisco Works Machine.
View 1 Replies
View Related
Jan 31, 2013
I have discovered my switches in LMS but it is showing unreachable what can be the reason ?
View 5 Replies
View Related
Oct 10, 2011
My DFM is showing 40 devices in the "Questioned" State. Lots of them are 3750 switches and 2801 routers. It has "Known" a few of the 3750s and 2800s, but most of them are Questioned. How do I go about troubleshooting this? It's
DFM 3.2.0, part of LMS 3.2;
I tried to reinitalize the DFM database, but that caused all sorts of other issues like my ANIServer not running anymore etc. I have a ticket open with TAC for that issue though.
View 3 Replies
View Related
Sep 29, 2011
I have added all of the devices to DCR and they show up with their hostname value in all of the device trees except for the fault manager views. In all of the fault manager views the hostname is not being used for the Devie Name field, rather the IP address is being used.
View 6 Replies
View Related
Feb 17, 2013
A particular & ungreatful person abused my laptop to the point where I had to install a password. I had to perform all kinda of removal actions but I just noticed in my network domain that his name followed by "PC" & under "media devices" & "network infrastructure" contains his name again w/ PC & devices called [TV]UNE40ES6100.I am using the program's wireless service which I am allowed-to. I just want to remove this person from my laptop. It won't delete when r. clicking. I have win 7 and use this laptop mainly for my online school & email.
View 9 Replies
View Related
Sep 28, 2011
We are using Campus Manager 5.2 with LMS 3.2. We have 100 devices and all 100 devices has been successfully discovered in Common services in all 100 devices are showing in DCR.When we check in RME we have found all 100 devices over there.
But, in Campus Manager we got only 95 devices. out of 88 WS-C2960G-24TC-L 5 switches are not showing in Campus manager. we have added the same manully ( manually included & Ecluded all 5 devices in Campus manager) and start the data collection, but no result.
After data collection it is showing not managed by Campus Manager when we check ( Show all Included devices option).
View 5 Replies
View Related
Apr 20, 2011
I noticed a TON of random devices showing up in my Network within Windows 7. When I say a ton, I mean 739! I am not computer illiterate, but definitely not a pro. My router is WEP password protected, so I'm not sure on earth is going on here. I thought maybe I had a torrent program open that could be affecting this somehow, but I don't..
View 6 Replies
View Related
Sep 3, 2012
I'm using the EA4500 router with Cisco Cloud Connect. I've noticed under Devices I'll see devices named "Network Device". They have a generic MAC address with something like "00:00:00:00:2F". They will have an IP that's already assigned to another device.
View 9 Replies
View Related
Aug 6, 2012
my intel inspiron N5010 not showing any wireless devices.
gave a link to download the whole driver pack.
View 1 Replies
View Related
Apr 26, 2011
I just got a DIR-655 and set it all up pretty easily. I have 6 wired and 3 wireless. All work fine and all are set to use DHCP. But if I go (in the router) to the Lan Computers list under Device Info, three devices (2 wired, 1 wireless) do not appear. I do have a switch added to the system, but of the three devices connected to it, 1 shows in th Lan Computers list and the other 2 do not.Since everything works, I'm mostly just curious why this is. Every previous router I've had showed everything correctly.
View 3 Replies
View Related
Dec 17, 2012
I'm not quite ready for the Automatic Failover feature that the ASA 5520 support. For now we have a cold stand by unit. I was wondering if I can change the mac addresses of the standby unit's interfaces to be exactly the same as the primary unit. I see an active/standby mac address section in ADSM, but I think that is used in the automatic failover function.
View 12 Replies
View Related
Apr 9, 2013
Not sure if it's new in WLC 7.4 code, but I now see "Dual-band radio" section everywhere in addition to "802.11a/n" and "802.11b/g/n". My dual band APs (for example 2600's) show up under both 802.11a/n and 802.11b/g/n as in the past. So what is this new category "dual-band radio" for then?
View 3 Replies
View Related
Nov 16, 2006
I Need to create more options on Cisco ACS 5.2 under internal identity store in users. How to do add, default not showing all.
View 6 Replies
View Related
May 27, 2012
I Need to create more options on Cisco ACS 5.2 under internal identity store in users. How to do add, default not showing all.i have seen on internet.
View 1 Replies
View Related
Mar 8, 2012
We have recently implemented a 3rd party certificate for the guest access, currently have a WLC 5508 that has a Vlan directly connected to our DMZ firewall and NATed out. The problem is when I have installed a 3rd party certificate as per the following link URL
The DNS host name that I entered into the DNS Host name section is not resolved. If I remove the DNS name and leave the virtual ip address 1.1.1.1 then it works fine but just comes back with untrusted message.
View 34 Replies
View Related
Jul 19, 2012
We have a NM-T3/E3-RF card that fits inside a 3800, but does not fit into a 3945.
The documentation says it works with 3900 ISR Routers.
Is there a cradle or adapter that is required?
Does the "RF" section of the part number differentiate this from a NM-T3/E3 card?
View 5 Replies
View Related
Nov 1, 2011
As seen from the pic below, I have DIR-655 with hardware revision B1 and firmware version 2.0. The printed, online, and in router manual says that there should be ALG section at the bottom, but as you can see there is nothing there. Is there any setting that makes the ALG section hidden?
View 4 Replies
View Related
Mar 1, 2011
My parents house is basically an old ranch style home that was added on to with a 2 story + basement. So I can only guess at the materials between where the signal is weak and where I have installed a DGL-4300 (Dlink Wired and Wireless gigabit router). It resides in the basement which is directly under the 2 story part of the house and everything on any floor of that section seems to get a good signal.
Admittedly I haven't done a lot of extensive testing since I really don't have much stuff that has wireless connectivity, and the one laptop they have is fairly stationary sitting right on top of the wireless router 2 floors up.....signal strength is always good to it.
However the older section of the house gets a pretty weak wireless signal and now with everything being wifi ready I am going to see about solving it. For instance, I've had a hell of a time connecting an older Zune 2.0 8gb version to the wireless network anywhere in the house, I just assumed it was broken or puking on the wireless security which is some version of WPA I can't recall atm if it's one in particular or set to both. But I temporarily disabled all security to see if it would connect and the router saw the device connect with a 20% signal strength for a bit, then the Zune started puking on connecting ..again.
I figured small device, it might even be broken. But I know the signal strength to the older section is not going to be very stellar anyway because the signal on a direct path has to pass through concrete walls and then a concrete foundation......plus it has cordless phone systems to compete against in that same space is has to travel. And anything the kitchen appliances and such might be interfering with it since it's potentially in the way as well.
So, any low cost solution (less than $50 dollars) I can hook into the existing wired network and will play nice with the existing Dlink router as it's going to remain the boss since it was fairly costly and works fine. To work as an extension of the same wireless network.....
I really don't have a problem with updating firmware, connecting into the device to configure it...or even putting new software on it if the directions are decent. The only thing I really care about is that it is cheap, has the capability to fit my bill. I'd guess it'd need to cover a 50 foot circular span with a strong signal and maybe 75 feet out with a medium strength to make sure there's no too weak spots or close up any potential dead spots due to materials used in construction. Oh and it has to be very stable or be pretty stable and have a remote reboot that'll clear up issues, I used to have a linksys router I had to reboot probably once a week to keep it working but it had to be power cycled. It was in the basement, near the patch panel the house has and it got old enough that I got the Dlink to replace it even though it was still functioned besides the freezing/sluggish performance issues requiring power cycles.
View 3 Replies
View Related
Feb 1, 2011
I successfully installed the AirLink101 AWLL6075 Adapter, however it cannot find networks because the Wireless Monitor section is always checked as being "Disabled". When I uncheck the box, a few seconds later it comes right back to Disabled with the check mark again.
View 14 Replies
View Related
Nov 4, 2011
Why is loop-back only working on ports forwarded in the Virtual Server section and not Port Forwarding or even DMZ? I have seen a post about loop-back on the DIR-655 from a while ago that had said to disable SPI and change NAT Endpoint to independent, I have done this and loop-back still doesn't work.
View 1 Replies
View Related
May 11, 2013
I want to prioritize League of Legends, a game which uses ports of ranging between 5000-5500. Does the WRT54GL "Application Priority" section allow for port ranges. If yes, have I put the range in correctly.
View 2 Replies
View Related
Feb 5, 2011
my computer is a dell dimension 1100, with a Linksys WMP54G wifi card, running vista home basic.In the wifi thing in the notification area, it shows two wireless networks, One is my normal SSID (Lower Net), and one is "Unidentified network". They are both on one wireless connection (Wireless Network Connection 3). When i try to go on the internet, it says i'm not connected. i tried disconnecting from the unidentified network, but that disconnects me from lower net too.
View 13 Replies
View Related
Oct 24, 2011
We are running WCS 7.0.1 and ACS 4.2 using TACACS for our techs to login to WCS (to manage access points). However, when the tech trys to run reports, they get an error:
Permissions Denied
The user is setup in Active Directory and not in WCS. I saw something about adding the user to a group in WCS but again the user is setup in AD. Is there something we need to do in ACS? Not sure what do do.
View 1 Replies
View Related
Jun 7, 2012
We have CPU reports set to run daily for some of our higher priority switches, and we've noticed that some of the data isn't meshing with what we see on the switch. We have one heavily utilized switch that reports near 100% CPU utilization sometimes. I can do a "show proc cpu history" on that switch and see that at least once an hour over 72 hours, we'll see a near 100% CPU utilization.
The problem is that these spikes never appeare on any of our reports. We'd like to see this info because even if the switch spikes for just a few seconds or a minute, it could still indicate that we may have issues. Without that in the report, we may never realize there could be a problem.
Is there a way for this info to show in the report? I'm under the impression that if LMS polls the switch and doesn't see a high utilization average, then maybe it doesnt' enter that in the report. I guess I'd just like to know how often it pulls this data, and how it decides wath the Min, Max, and Averages are.
View 1 Replies
View Related
Jul 2, 2012
I have modified my radius accounting reports using "interactive viewer" and saved successfully but the exported report doesn't reflect these changes. I'm just wondering what's the point of being able to modify the reports if you can't export your changes or there is something I'm missing?
View 3 Replies
View Related
May 1, 2012
We use LMS 3.2 with the latest patches. In IPM we have a couple of collectors (availabilty latency etc) and reports for our customers.
The polling interval for all collectors are working hour 7:30 - 18:00 Mo - Fr.
Unfortunately the polling detail is not included in the PDF report. Is there a way to include this information in the report.
View 1 Replies
View Related
Apr 3, 2012
We're currently running on ACS 5.2.0.26.9 with 2 appliances (one primary and one secondary).Today, I wanted to get some reports from the Monitoring and Reports tool. At beginning, it seemed impossible to generate them. Later, I decided to reload first primary and then secondary. As soon as I've done it, I got an email alert telling me that it failed parsing NAD.
Cisco Secure ACS - Alarm Notification
Severity: Critical
Alarm Name
System Alarm [Collector]
Cause/Trigger
[code]....
I don't really find where I can find the Collector log...Anyway now when I generate a 30 days report, I only get data up to 23.03.2012. Nothing recent !
View 7 Replies
View Related
Jul 7, 2012
Is there a way I can get the ACS (5.3) to email some of it's reports on a schedule?I'm hoping to send automated summaries of failed logins to the service desk each Monday morning.
View 3 Replies
View Related
