Cisco :: 6509 - LMS 3.2 CM Device Discovery Multiple Interfaces
Apr 2, 2012
we use LMS 3.2 in our network. We have a couple of 6509-V-E Switches with mutiple interfaces (VLAN interfaces and Layer 3 interfaces) The problem is, campus manager discovers the switch by a interface randomly...one time its a lay3 Interface and another one its a vlan interface which none of them are in DNS hence no name resolution can be made.
Is there a way to "tell" CM to us for instance the VLAN Management IP of the switch?
View 2 Replies
ADVERTISEMENT
Feb 15, 2011
How to hit the 32 interface nbar limit on an ASR? Our ASR1002 ESP5 is now grumbling: %NBAR-4-STILE_MAX_PD_INTF: NBAR protocol-discovery is enabled on maximum number of interfaces (32) supported by this platform..Is this expected to increase in future software revisions? (or is it a h/w limitation?)Is it the same limit regardless of ESP or will I get more (how many more?) if it is an e.g. ESP20?
View 1 Replies
View Related
Sep 8, 2011
I am using CISCO PRIME LMS 4.1 for manage my network, i ran a device discovery job using a ping sweep on the ip ranges of my network, ie 192.168.1.0/24, 192.168.2.0/24 and so on... the discovery found all my devices, but it discovered duplicate devices with illegal ip Addresses, i.e.,
ip device
192.168.1.255 S1
192.168.2.0 S1
192.168.2.1 S1 (the real address)
all in reachable status.
I don't understand why the program adds that repeated illegal addresses.. How can I run the device discovery to avoid this problem?
View 2 Replies
View Related
May 13, 2013
I am trying to build a new network from scratch, I have the WLC 5508 w/ Aironet 3600e APs connected to my Netgear Smart Switches and a Linksys RV082 router that I'm using as my DHCP server with several VLANs for several stuff on my Switches.
I have 2 questions:
1. Can I have 5 Interfaces configured on 5 different VLANs, each SSID on each a different Port:
Port 1: Controller management only=> 192.168.x.x /24
Port 2: SSID 1: WiFi Internal=> 172.16.x.x/12 (Radius Auth with no sharing)
Port 3: SSID 2: WiFi Internal w/ sharing=> 192.168.x.x/24 (Radius Auth with sharing)
Port 4 :SSID 3: WiFi Guest=> 10.0.x.x/8 (Web Auth)
Port 5: SSID 4: WiFi IT=> 192.168.x.x/24 ( Radius or certificate Auth with access to the controller management interface)
2. How can I use the Controller as the DHCP server for all the WiFi traffic, and how should that be configured to work with my other DHCP server?
View 3 Replies
View Related
Jan 18, 2012
we are running CiscoPrime LMS 4.1 and I have the following problem.I have configured SNMP Settings as shown below (the order of the targets is exactly as it is configured on the server):As can be seen we use three different read community strings. I also have exluded a bunch of IP ranges and IPs from the filter settings. When I manually start discovery everything works fine, meaning that all devices in the above ranges that need to be discovered are discovered as "reachable". The problem appears in the scheduled discovery (happens once daily). In that case only the devices with Read Community snmp1, get discovered as "reachable". All other devices with Read community snmp2 & snmp3, as well as those that are excluded in the filter settings, are discovered as "unreachable".The discovery uses DCR as seed and seed devices are also configured.I also have a problem with PingSweep in the discovery, but I will open another discussion so that I don't complicate this one too much.
View 1 Replies
View Related
Aug 1, 2011
I´m getting started on ciscoworks and i trying to configure a device discovery to start but i have some questions about how configure this tool exist 5 parameters that i have to configure to start the device discovery.
•Configuring Discovery Module Settings
#
•Configuring Seed Device Settings
[Code]....
I want to add devices that found neighbors via CDP son in the configuring discovery module setting i choice that option In the configuring seed device setting i choose DCR as seed device that means those devices already in the DCR start discovering from those devices but you can add more seed devices how i can add a seed device ? with ip addres or something like this? and this device have to be in the DCR already or not? The configuring SNMP settings, this community correspond to what device? the devices that i want to add ? and in the field target name what ip adders have to be? and if i have different community of snmp in my devices what device and snmp community have to configure in this parameter
View 1 Replies
View Related
Jun 20, 2011
I use the Edit Identity option to change the "Display Name" from an IP to a station name, it is overwritten when a discovery has been done. I have checked the discovery settings and tried using the update DCR Display name setting to prevent this from happening, but it makes no difference.Is there something i am missing? This is on LMS 3.2?
View 2 Replies
View Related
Nov 7, 2011
I have a very special usecase with migrating devices from LMSv2.6 to v4.1 using DCR bulk import that was maintained manualy, not by discovering.The special thing is each device has its own SNMP-community and its about 1500 devices.RME discovery works fine, but I get the devices not discovered by DCR (CSDiscovery), because I need a minimal DCR discovery configration containing Seed and SNMP-settings. So I activated DCR as seed, but cant skip SNMP settings without an entry. But in this case I would need 1500 SNMP-lines that would be very unhandy. is in CSDiscovery-Settings a possibility to can leave SNMP settings untouched so it takes the credentials from the DCR, to can start DCR discovery?
View 6 Replies
View Related
Apr 19, 2012
I have problem in recently installed LMS 4.1 Device discovery will not start when launched manually. When i hit the button, it doesn't even give a popup window saying that the discovery is started and that email will be sent... If I schedule it is launched, runs and finishes correctly. All proceses are started and it seems that application is working ok. LMS is installed on Win 2008 R2.
View 1 Replies
View Related
Feb 19, 2013
The problem is that - although negotiated in global discovery settings - Prime appends domain name to the device name so that all switches (not routers) have "confusing names". The domain name is not required in device name. What can i do?
View 2 Replies
View Related
Mar 9, 2010
Is it possible to have multiple dhcp pools for multiple VLANs? The switch is a 6509 and/or 4506 catalyst. I don't want to use server-based products.
View 5 Replies
View Related
Jan 6, 2012
Is there a limitation to the amount of sub-interfaces that can exist on a Cisco 6509? The switch has WS-SUP720-3B (Sup card), WS-X6724-SFP (linecard), and 12.2(33)SXH7 (IOS).
View 7 Replies
View Related
Mar 7, 2013
I have an ASA connected to 2 ISPs.I am using object tracking for the default route so only 1 path is used at a time. I have a L2L VPN setup going out interface A. I would like to configure a 2nd VPN going out interface B with identical parameters.
(ASA software 8.2)
crypto map PATH_A 1 match address outside_1_cryptomap
crypto map PATH_A 1 set peer 10.1.1.1
crypto map PATH_A 1 set transform-set ESP-AES-128-SHA
crypto map PATH_A 1 set security-association lifetime seconds 28800
crypto map PATH_A 1 set security-association lifetime kilobytes 4608000
crypto map PATH_A 1 set reverse-route
[code]....
View 2 Replies
View Related
Apr 1, 2013
If I have a PI 1.2 system that has multiple interfaces configured I can upgrade to PI 1.3 and both interfaces remain and I can see both under the admin webpage under appliance interfaces. But if I do a fresh install of PI 1.3 I can only configure one interface. The commands fail from the cli to configure anything but gigabitethernet 0. Are multiple interfaces not supported in PI?
View 2 Replies
View Related
Jan 15, 2013
Having upgraded to 8.3 from 8.2 I and read much about the differences , it seems that 8.3 deals with NAT in a much more managed method.However I am confused on how one would NAT a network object to multiple interfaces? i.e I know you can specficy a NAT adddress within the network object howeveer this only allows you to specific a single IP address.What if I want to talk accross multiple interfaces how would I specify this?
View 5 Replies
View Related
Oct 28, 2012
how I can check the qos counters and stats for interfaces on my cat 6509 ?
View 1 Replies
View Related
Jun 16, 2011
We have an ASA 5510 firewall. There are 4 ports on it configured as 2 outside, one inside, and one DMZ. We have two cable modems attached to the outside ports. Our plan is to have the "inside" port directed to one outside port/cable modem, and the DMZ port directed to the other outside port/cable modem.
We have been able to get the "inside-to-outside" setup to work but not the "DMZ-to-outside" setup (at least at the same time).First off, is this possible? If so, what are we likely missing - some way to have a second default route for the DMZ?(My manager is the "Cisco person" here, not me, so I may not have enough info.
View 1 Replies
View Related
Aug 20, 2012
I am trying to enable a second WAN interface on our ASA.the end goal is to move all internet traffic to the new connection, but first i want to test it working.I have setup my computer as an object in the ASDM and the interface is configured correctly (same settings on a different router and that was working)I setup a route with a lower metric ( 1 lower than the default route which routes everything through current main internet interface) to route traffic from my computer out through the new interface but i am still connected on the old interface.I duplicated some of th NAT rules (but i would have thought if these werent working then i would have no internet connection anyway)
View 5 Replies
View Related
Feb 24, 2011
I am trying not to run before i can walk,.. so first thing I'm trying to do is ping out to a DNS server in the internet: 212.135.1.36 from my internal network.
- If I put a default gateway on my router, and set to 172.16.32.254 (Firewall Vlan100 interface) and ping,.. it works fine from my router.
- If put a default gateway on my switch below the router as 172.16.32.252 (VLAN100 interface of the router) and ping from the switch it doesnt work.
I assume its getting to the switch as I can ping the 172.16.32.252 from the switch so the router is dropping the packets... my question is why!?
Once this bit works,.. the intention is to route any external bound traffic that comes from VLAN100 to 172.16.32.254, external bound traffice from VLAN200 to 172.16.64.254 etc etc
[Code] .....
View 5 Replies
View Related
May 12, 2013
I have c3725 router that have two WAN interfaces, both of which I want to serve VPN clients. However, I have only one default route, say for WAN1, so how can I accept client requests on WAN2.
ps: I use vpdn and pptp, and I'm a newbie to Cisco router and IOS.
View 4 Replies
View Related
Jan 24, 2011
I have 2 routers ( Cisco 3845's) both running identical IOS's. Each router has identical 5 networks on it with one network each being different.I have HSRP set up on the identical 5 networks.Your standard Fail over senario.ON one of the routers one network is not seeing the other router in the same network, Will not Ping or traceroute.And HSRP stopped working ( both were thinking they were active. which of course brought the network to a halt. Non of the interfaces has any ACL on them, They are plugged into a Brand new Cisco 3560v2 switch. I have switches out the cables to eliminate that as an issues.
View 1 Replies
View Related
Jan 3, 2012
I have a 5508-WLC appliance and configured multiple ap-manager interfaces to balance the join request from LAPs and the load.I went to console port from some LAPs and saw that there was that balance among multiple ap manager interfaces (Dynamic AP Management Interfaces). Then we torn down one of the ap manager interfaces and confirmed that the LAPs were moved to next ap manager interface automatically.But the question here is, how can I verify which ap-manager interface was used for a LAP from the WLC via GUI or CLI ?? or how can I see the amount of APs joined using that ap manager interface from WLC ?
View 2 Replies
View Related
Apr 10, 2013
I am trying to lab something up and I believe I am doing something incorrectly. My management VLAN works fine, the AP on port 7 finds the controller fine, but my VLAN 80 doesn't seem to be mapped to port 2. I mapped a test WLAN to the VLAN, and setup a DHCP scope, and a client can get on the WLAN, acquire an IP address, etc. I thought I coudl then map that VLAN (80) to port 2 and have it go out a cable modem. Doesn't seem to be working that way, however.
View 3 Replies
View Related
Sep 23, 2011
I have an ASA 5505 running 8.2(1), that is configured with three interfaces as follows:
Inside (security 100) 10.0.0.0 /24
Inside 2 (security 100) 192.168.0.0 /24
Outside (security 0) internet
Inside is connected to my internal network, inside 2 is connected to the network of a sister organization, outside is outside.
I'd like to be able to route between from inside to inside 2, and have NAT translate me to inside2's address.
I have inter-interface traffic configured, and when I use a NAT exemption, I can route fine. But the resources on network 2 must see my request as coming from the inside2 interface IP.
View 2 Replies
View Related
Feb 12, 2013
This is for an ASA 5505 with the base license...I have a situation where I will not have one interface in my outside VLAN, but instead I want to have interfaces 1-7 in my outside VLAN and interface0/0 in my inside VLAN.
Is this supported with the Base license, and if so how would I do this? Do I still just need to assign one IP address to the outside VLAN?
Or will I need to upgrade to the Security Plus license and put each interface in a separate outside VLAN, so in essence I would have 7 outside VLANs each with the same security level (0)?
My situation is that I have several partner networks that i want to "aggregate" thru my one ASA 5505. So each outside interface represents a separate partner (outside) network, each of which I want to get to from my inside network. Hence the many outside to one inside.
View 5 Replies
View Related
Nov 21, 2012
I have a virtualization server with 4 network interfaces and connected it to a SAN. There are few virtual machines which writes data to the SAN.
I want to connect to the SAN with multiple interfaces to speed up the network.
Is it possible to send data on multiple interfaces? How can I configure it?
Computers are connected to san through switch.
SAN: Equallogic PS 4100 E
Switch: Dell Power Connect
Computer: Dell T610
OS: Centos 5
Virtualization: Kvm
NIC: 8
I am not sure about network card brand now.
View 1 Replies
View Related
Jan 14, 2012
I am having big problems trying to get what should be a rather simple configuration to work.I have a Cisco 2901 Router and have setup Zone Based Firewall on this.Traffic from the 192.168.223.x network does not pass through to the 192.168.1.x network.my traffic appears to disappear down the big bucket...Interesting I can ping machine on 192.168.223.0/24 network from the 192.168.1.0/24,So the static routes setup on the router on the 192.168.1.0/24 appear to be routing ok.
View 4 Replies
View Related
Mar 20, 2012
I've got a question concerning the configuration of multiple AP manager interfaces on -for example- a cisco WLC 2504. I've read the configuration guide but I'm not sure whether this is the way the protocol works. Say I want to distribute AP's (and traffic) across various AP Manager interfaces on the WLC. I would configure the following:
Create one management interface (which will automatically also be an AP-Manager interface)Configure 1 (or more) Seperate ap-manager interfaces, assign them to a port number, and select "Enable dynamic AP Management". VLAN ID's will be the same.Create a WLAN and configure it's interface to "management" Is it correct if I state that the LWAPP protocol takes care of the discovery from the Access Point and sends information about the available AP-manager interfaces back to the AP and the AP knows which ap-manager interfaces are available, connecting to the least loaded one?
View 3 Replies
View Related
Oct 10, 2011
I've been trying to figure this one out for quite a while. I currently have 2 inside interfaces (data, phone) and I am moving to 3 inside interfaces (servers, workstations, phones). I have not been able to get any traffic between the interfaces. With the current setup it was not a major problem. With the new setup it will be a major problem.
Below is a sanitized version of the config.
ASA Version 8.2(1)
!
hostname BOB
[Code].....
View 11 Replies
View Related
Oct 18, 2012
Due to special circumstances we have 2 ISP links on an ASA5510. I am trying to terminate some L2L VPN tunnels on one link and others on the second ISP Link, eg below:
LOCAL FIREWALL
crypto map outside-map_isp1 20 match address VPN_ACL_Acrypto map outside-map_isp1 20 set peer 1.1.1.1crypto map outside-map_isp1 20 set transform-set TS-Generic
crypto map outside-map_isp2 30 match address VPN_ACL_Bcrypto map outside-map_isp2 30 set peer 3.3.3.3crypto map outside-map_isp2 30 set transform-set TS-Generic
crypto map outside-map-isp1 interface ISP_1crypto map outside-map-isp2 interface ISP_2
crypto isakmp enable ISP_1crypto isakmp enable ISP_2
route ISP_1 0.0.0.0 0.0.0.0 1.1.1.254route ISP_2 3.3.3.3 255.255.255.255 2.2.2.254
Establising the VPN tunnels in either direction when using ISP_1 works fine establishing in either direction from remote access users and multiple L2L tunnels (only showing one for example).
On ISP_2
1. Peer 3.3.3.3 device establishes a VPN tunnel, but the return traffic does NOT get back to devices on 3.3.3.3 tunnel.
2. The local firewall does NOT establish a VPN tunnel going to 3.3.3.3
It would seem to indicate that the problems lies with this multihomed firewall not directing the traffic correctly to either return down and establised VPN tunnel (point1) or to intiate a tunnel if none exists (point 2).
Reconfiguring the VPN tunnel peer for 3.3.3.3 to be on ISP_1 of the local firewall, all springs into life! There are sufficient license etc...
View 4 Replies
View Related
Jun 26, 2012
The PC I'm using right now was built almost six years ago (ASUS A8N-SLI Premium), but it has dual Gbit NICs. My home file server was built four years ago using an entry level server board (Tyan S5211G2NR) and it also has two Gbit NICs.
I never quite understood how to take advantage of the multiple network interfaces. Can it be done through a standard unmanaged Gbit switch?
I'm building a new desktop, probably using the ASUS P8Z77-V mobo, which has just one NIC.
View 9 Replies
View Related
Sep 17, 2011
I am wondering if xconnect L2TPV3 feature could be done on multiple SVI interfaces on 871 router and 2911 router with built in 8 port switch?Like I need to extend two ethernet interfaces and can I use two SVIs on router built-in switch module on each side?
View 2 Replies
View Related
Feb 24, 2013
i have a question about multiple TACACS Groups. I want to archive the following:
A Cisco 888 is managed by me and a Provider Support Team. Since we both want to access our own TACACS Server, i want to create two TACACS Groups. Is it possible to me, to bind a Tacacs Group to one Interface, and the second TACACS Group to another ? Means that our stuff is connecting to the LAN Interface FastEthernet0 that is applied to the SVI in V LAN 1.
The service technicians from the Provider are connecting to the external Interface or through a possible Lo. (another IP). I do not want to mix our 2 TACACS+ Server and theirs together in one Group. So have anybody tried this before ?
View 8 Replies
View Related
