I can connect to the internet after 5mins or so after booting up but after that internet will not respond at all.i need to restart again my PC in order to connect again to the internet i somehow manage to bump with this solution using ping command.whenever i boot my pc i need to open this command and i can surf the internet without getting my connection lost just as long ping command is open.
View 5 RepliesThrough wireless. WIFI is activated but internet is not active. Why?
View 1 Replies View Relatedwhy using ping to test the functionality of an ACL could proove insufficient?
View 9 Replies View RelatedWhat is the data contained in the PING Command? and 32 and 64 bit PING how it differs?
View 1 Replies View RelatedWho is trying the ping www.dlink.com ? I have been used the model DIR-825 during 1 year, but I could not see that ping command in the log. I had experienced that my notebook alert that DIR-825's shareport has reconnected. Why the DIR-825 lost the private connection while I sleeping?Comment: DIR-825(IP: 10.10.100.97/28) is private using only. The internet gateway is setting to DIR-655(:192.168.90.97/29). [code]
View 1 Replies View Relatedif you have two no of win 7 computer , and you run ping command at the same time at both PCs but the successfull at only one PC , second computer shows unsuccess full ping
View 2 Replies View RelatedCisco 887 I can ping to 4.2.2.2 but can't connect to Internet
View 13 Replies View RelatedI recently acquired an E4200 Linksys router.Is it possible to connect to it using telnet (from LAN)? For example I would like to start a ping command directly from the router.I tried to telnet using command line shell from Windows and it failed to connect on port 23.
View 4 Replies View RelatedI got a trojan and removed most of it with Malware Bytes. My computer was still acting squirrely so I read that I needed to delete a ping file. I did and can no longer connect to the internet. It just sits and tries to acquire the IP address. I have reset my winsock and tried uninstalling and reinstalling my network drivers etc..
View 3 Replies View RelatedI have a netger router/moden connected to my phone line for broadband, an ethernet cable coming out of that to a netgear switch an then a cable going from the switch to fa4 on the 861. I can ping the netgear router from the 861, however, when I connect my PC to it, I am unable to ping let alone connect to the internet, the PC is getting an IP from the 861 and I can ping the fa4 interface from the pc. I just don't understand my I can not ping the broadband router, I even added a static route to the netgear with no luck.
View 5 Replies View RelatedI got a new HP laptop running Windows 7. When I turn on my laptop, my wireless is off. So I click on F12 (my wireless button), to activate my wireless. The orange light turns blue. Even though the light indicates that my wireless is on, I have to go to device manager>networking>802.11n>advanced then activate my radio for my laptop to pick up the wireless signals. The problem is that I have to do this every time I turn on my laptop, and its getting quite repetitive.
View 4 Replies View RelatedConnecting The Internet by Ethernet Lan-cable (without a router), ping to Yandex.ru is 4 ms. If we connect by router ping is 27 ms. If we ping by web-interface it is 4 ms. Connecting by Wi-Fi it is 27 ms.I' ve substituted the cable connected router and computer. So my questions are: why ping is rising when I connect to the Internet by router?
View 1 Replies View RelatedI have a Cisco RV082 that doesn't appear to filter any selected categories. To run through what i've done so far, within the 'Web Protection' screen i've: enabled URL filteringconfigured a number of categories to filter by putting a tick in the repective business hours boxset the business days to 7 days a weekspecified business time as 24hrshit the save button.
My licence appears as activated and my platform shows as "gateway service".I've gone on to a number of machines and all are able to access websites that fall under my blocked category (facebook for example even though i've blocked the social networking category).
Since I moved our WLC Controller ( 5508 ) from Version 7.0 to Version 7.2.111.3 I got above failure messages. Until now I changed the radius timeout from 2 to 10 seconds and also I disabled the aggressive failover without success. What else it could be ?
View 3 Replies View RelatedMy rv082 router protect link gateway is already activated. How do i change the key or activate it with a new activation key?The router dont have any link to change the key. I'm using v1-2 rv082
View 4 Replies View RelatedFrom My Router that connects to Cable modem i am unable to ping website 4.2.2.2I am able to ping all other websites fines.Same website i can ping from my pc and all other switches fine.Router has only 1 ACL thats for NAT.
View 25 Replies View RelatedI got a problem yesterday with a customer that says that the calls from a CISCO IP Phone 7961 to an Alcatel 4018 IP Touch didn't work, well the phone rings but there's no voice; I manage a CISCO ASA version 8.2(1) and I was checking the Inspection Rules in the Service Policy Rules section and when you open the inspection_default at the Rule Actions tab I find that the H.323 H.225 and H.323 RAS box wasn't checked so I ask to the customer to made a test and the same problem happen so I checked both box and again ask to the customer for a test and it works.
I was talking to a partner and he said that maybe this Inspect fix some signaling parameters of this protocol that can't work fine behind of a firewall.
what i type in run box to increase INTERNET speed i saw my net provider doing this just little bit time he just type in run box ping o (.......................)/ and some numbers like IP address and then black window opened and INTERNET speed increase tell me what i type in my run box to increase speed.
View 2 Replies View RelatedThe server is on a different network and the desktop is on a another network.I can ping the server but i can't access any drive on the server.
View 1 Replies View RelatedI have a laptop that works perfectly fine when plugged into a network cable, but the wifi refuses to work. It pulls an ip, and everything looks good when I run ipconfig/all, but it can't even ping the router. All other computers on the network are working fine. I've flushed dns, set static IP and DNS, uninstalled/reinstall device, updated drivers, bios, and firmware, and even created a backup image of the computer and reloaded the os using the recovery partition. The event log doesn't tell me anything, and there are no flags in the device manager. I'm at a complete and total loss. I cannot figure this one out.The laptop is a Compaq Presario CQ50-142US. Vista 32bit OS. Everything was working perfectly fine before it got a virus. I ran through the standard procedures of AVG, Malwarebytes, TDSSKiller, and even resorted to Combofix, but somewhere along the line the wifi dropped off and will not come back.I even double checked the HOSTS file and IE proxy settings to ensure I wasn't crazy; although I know those should've affected the wired connect too.My last step is to either replace the wifi chip (which I don't think is the problem), or wipe it and load the os from scratch, but I don't have an oem disc since it has the recovery partition.
View 14 Replies View RelatedMy parents Windows 7 PC has suddenly stopped being able to connect to the Internet. Using the "Diagnose problem" feature in the Manage Network Interfaces panel results in a message claiming that it cannot reach the DNS server and that the connection needs to be reset. Doing so has no effect. It is connected to a DSL router via an ethernet cable.The NIC is set to dynamically receive its IP and DNS settings via DHCP which it obtains from the DSL router. Executing ipconfig from a DOS prompt shows that this is occurring as expected, with an assigned IP of 192.168.2.10. The gateway and dns are set to the IP address of the router, which is 192.168.2.1. Note that I can't even ping the router at 192.168.2.1.I also tried static settings in the available range and tried using open DNS IP addresses.
They also have a laptop which connects to the same router wirelessly using DHCP and it is working fine. Using this laptop, I can log into the router and see both it and the problem PC in the list of connected devices, each with the dynamically assigned IP addresses as seen using ipconfig on each. Unplugging the ethernet cable shows the connection status changing in the list of connected devices in the router. From the laptop, I can ping the router and running ipconfig shows that it obtains the same gateway and dns as the PC and the next available IP - 1292.168.2.11.So this leads me to believe the following:
1- The router, NIC and cat 5 ethernet cable are working fine at the hardware level.
2- The DNS settings in the router are fine, as the laptop works
Perhaps coincidentally, the same day it stopped working they received one of those bogus "This is Microsoft calling" calls claiming their PC was infected, but they had heard of the scam and hung up. Naturally, I started suspecting a virus, but a full system scan using McAffee produced nothing. If it was a DNS changing virus, would I not still be able to ping the router using the IP address?
I reconnected my SB after letting it sit powered down for 6 minutes to lose all of its configuration and I was then able to get it to connect to Cox's provisioning site and was able to get online with it, had to then force my router to re-detect the connection and now it is also working.Last night my ISP had an outage, or something, and I was not able to connect for quite awhile, keep in mind that my modem was working all day yesterday.It came back up around 2:30 or 3 am last night but since I was rendering some footage in Sony Vegas I did not check to make sure everything was good. So I get on my computer this afternoon and find that I am not connected to the net and that I can not ping nor connect to my SB5101. Pings all say Request timed out.All of the lights that should be on are on: power, receive, send, online all green, activity solid amber, which is almost never solid usually flashing. So I power cycle it and my router and plug them back in but now the internet light on my router never turns green, just flashing/solid amber.I am able to connect to my router, a netgear WRG3500, through the gui interface just fine. So I connected directly to my surfboard and was still unable to pull an ip address or connect to the gui for it. All pings and address renews resulted in request times out or media disconnected messages.At this point it is looking like my SB has gone bad, but I do not see how that could possibly be. These things usually have downward slides into crappy brokeness, this was immediate without any problems for 2 years.I am connected atm with my old D-Link DCM 202 modem I had before this one, which does not want to talk with my router, not sure why.
View 1 Replies View RelatedI am having problem connecting to my work PC via VPN Cant ping and RDP. I sometimes need to log into my work PC to check out a problem. I connect via VPN and I can access servers (using Citrix and local intranet sites) that can only be accessed once connected to my work domain. So it looks like the VPN actually works fine.
But I cannot Remote Desktop Connection to it. I also tried to ping the PC using a command prompt. Using the command prompt, I ping MyWorkPC And I can see that it tries to ping MyWorkPC.domain.name.co.za. So it looks like it sees the MyWorkPC on the network. But all pings fail.
A work colleague tried to remote connects to MyWorkPC from his home PC and he can successfully connect. So I do believe that the work network and PC is setup correctly. I am running window 7 Ultimate SP1 (32bit) with a 3G dongle in a router. I also have Avast antivirus installed on my PC. I was not sure if the router or the antivirus was the issue so I tried:
1.Removing the 3G dongle and attach it to my USB port on my home PC directly. No luck
2.Some blogs said that the P2P or IM shield on Avast might be the problem so I disable it. No luck
3.Then I uninstalled Avast completely to see if it has any shield that might still block it. I restarted. No luck
In the office we have 3 printers (2 network 1 attached locally to my machine). I can ping all of the printers and no packets are dropped, however I cannot connect to them.I know the printers arent faulty because all of the other staff have no problems printing.I have tried re-installing drivers, disconnecting the printer and reconnecting it etc. and I just cant find what the problem is
View 4 Replies View RelatedI am trying to set up a lan to lan vpn access with 2 asa5505's but I cannot ping, traceroute or connect from either side. I can connect to both ASA 5505's from the internet, and connect to the internet FROM both 5505's, just not one to the other. I can ping the network GATEWAYS to the routers, just not the routers themselves.
Both of these machines have been configured for previous VPNs but that configuration has been removed.
I have two computers side by side 192.168.1.7 and 192.168.1.8 both running xp pro sp3. On 8 I can RDC to the 7, but on 7 I cannot RDC to 8. I can see port 3389 listening on both using netstat -a. But 7 just can't RDC connect to 8. 7 cannot ping 8 either. I have the firewall turned off on 8, I had tried allowing RDC 3389 earlier with the firewall but that didn't work either.I don't have any extra firewalls running.Life will be like perfect, if I can just RDC to 8.Both are on the same wired belkin wireless router, 4' from itl.I tried taking the no ping no rdc computer to work and it didn't work there either.
View 19 Replies View RelatedWhen I try to ping ipv6.xsnews.nl on either of my Windows 7 computers, it returns "Ping request could not find host". But when I do it on XP, it succeeds. I have tried putting the W7 PC in the DMZ, disabling the software firewall but it doesn't work.
What I think it involves is having ipv6 installed on each. I tried to duplicate the setup of both the XP and a W7 computer, installing the gogo6 tunnel. But apparently it's not setup on this computer because the ping result is the same as on the third computer which hasn't had ipv6 installed. s not setup on this computer because the ping result is the same as on the third computer which hasn
I have an ASA 5510 with the configuration below. I have configure the ASA as remote access vpn server with cisco vpn client, my problem now is I can connect but I can't ping.
Config
ciscoasa# sh run
: Saved
[Code].....
cant get online,found that the internet IP ping failed
View 24 Replies View RelatedI have strange problem I am using my static ip system since two year, I dont have issues so far, since two days I am facing a strange issue when I am piging my system I could able to see reply,
but when I am trying to connect via MSTSC..blank screen even I am unable to get login screen also...
I have tried to connect to log mein and team viewer all are having the blank screens
Ran a diagnostics test and failed the Ping test. I'm using the university resident internet. Called the tech place and they said they're investigating their connections and networking thing on their end. Just in case though, I want to know if there's actually something wrong with my laptop rather than their equipment.
Microsoft Windows [Version 6.1.7600]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:UsersHelen>IPCONFIG /ALL
Windows IP Configuration
Host Name . . . . . . . . . . . . : FATHERSCOMPUTER
Primary Dns Suffix . . . . . . . :
[code].....
I have recently bought two 1800 cisco routers and have tried to connect them over wan serial link, but I am having problems when trying to access resources on the other side. I am a newbie to cisco and I wonder if the problem is with the configuration or the new routers or the serial link between the sites. Below is the show-running config results I have done on both routers; I can ping the serial interfaces from both sides and remotely, but I can't ping hosts or FE from other side.
View 8 Replies View RelatedI recently deployed an ACE 4710 Appliance. Configs seems right but clients cant Ping the VIP and acnt also connect to the VIP. Also VIP Dosent show in 'sh arp'.
See the configs!!
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2011.10.11 10:48:14 =~=~=~=~=~=~=~=~=~=~=~=
sh runGenerating configuration....
[Code].....