Cisco WAN :: 861W - Unable To Ping And Connect To Internet When Connected To Pc
Nov 19, 2012
I have a netger router/moden connected to my phone line for broadband, an ethernet cable coming out of that to a netgear switch an then a cable going from the switch to fa4 on the 861. I can ping the netgear router from the 861, however, when I connect my PC to it, I am unable to ping let alone connect to the internet, the PC is getting an IP from the 861 and I can ping the fa4 interface from the pc. I just don't understand my I can not ping the broadband router, I even added a static route to the netgear with no luck.
I tried my entire afternoon trying to figure this out but to no avail. Fortunately, I found this place out of my desperation for a solution. My netbook works very well in my home network but when I brought it to my workplace, I was unable to connect to the internet eventhough I could connect to the wireless network. Other computers and laptops were able to connect and use the internet well using the same router. I tried manually configuring my IP and default gateway based on what I read but nothing worked.
Tech Support Guy System Info Utility version 1.0.0.2 OS Version: Microsoft Windows XP Home Edition, Service Pack 3, 32 bit Processor: Intel(R) Atom(TM) CPU N270 @ 1.60GHz, x86 Family 6 Model 28 Stepping 2 Processor Count: 2 RAM: 1011 Mb Graphics Card: Mobile Intel(R) 945 Express Chipset Family, 224 Mb Hard Drives: C: Total - 109474 MB, Free - 7145 MB; Motherboard: Acer, Antivirus: Avira AntiVir PersonalEdition, Updated: No, On-Demand Scanner: Enabled
From My Router that connects to Cable modem i am unable to ping website 4.2.2.2I am able to ping all other websites fines.Same website i can ping from my pc and all other switches fine.Router has only 1 ACL thats for NAT.
I have created a VPN connection for ASA 5512-X by using the wizards and nothing seems to be wrong on the wizards's config.I am able to connect to the network by using the VPN but unable to ping internal network.Below is my config for your reference:
Result of the command: "sh run" : Saved : ASA Version 8.6(1)2 ! hostname FAA-ASA-1 enable password crzcsirI44h2BHoz encrypted passwd 2KFQnbNIdI.2KYOU encrypted
I have two computers side by side 192.168.1.7 and 192.168.1.8 both running xp pro sp3. On 8 I can RDC to the 7, but on 7 I cannot RDC to 8. I can see port 3389 listening on both using netstat -a. But 7 just can't RDC connect to 8. 7 cannot ping 8 either. I have the firewall turned off on 8, I had tried allowing RDC 3389 earlier with the firewall but that didn't work either.I don't have any extra firewalls running.Life will be like perfect, if I can just RDC to 8.Both are on the same wired belkin wireless router, 4' from itl.I tried taking the no ping no rdc computer to work and it didn't work there either.
I have a home network of 3 cmputers. DHCP from router. 1 computer is not getting address. But if I assign it one, with same gateway and dns(not a duplicate ip of others), it can ping internally, and outside. I can do tracert to 8.8.8.8 and ping it (google DNS). But I can't get to internet. So - i can get out, but nothing coming in. I have checked firewall.
I have strange problem I am using my static ip system since two year, I dont have issues so far, since two days I am facing a strange issue when I am piging my system I could able to see reply,
but when I am trying to connect via MSTSC..blank screen even I am unable to get login screen also...
I have tried to connect to log mein and team viewer all are having the blank screens
Ran a diagnostics test and failed the Ping test. I'm using the university resident internet. Called the tech place and they said they're investigating their connections and networking thing on their end. Just in case though, I want to know if there's actually something wrong with my laptop rather than their equipment.
Microsoft Windows [Version 6.1.7600] Copyright (c) 2009 Microsoft Corporation. All rights reserved. C:UsersHelen>IPCONFIG /ALL Windows IP Configuration Host Name . . . . . . . . . . . . : FATHERSCOMPUTER Primary Dns Suffix . . . . . . . :
I need another set of eyes on my config. I am trying to set up my router for a basic connection for the time being. I set my gig 0/0 port to dhcp I see traffic being sent and recieved but I can not ping 8.8.8.8. I am connected to a basic comcast modem from 0/0 I have also tried setting gig 0/0 to 100 full. I do have IP routing enabled. I believe I have my acl's configured correctly. I am wondering at this point if I need a static block of IP's from comcast.
I have setup 5505 ASA for Testing purposes. It has static route to layer 3 switch on outside interface that goes to the internet.
ciscoasa# sh route Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
I have just setup the 3G Wifi Router (Huawei 3G21WE) for my company at remote site for temporary use.Now we want to monitor the DVR and cameras installed on the site from head office but i am unable to do it.I have done the port forwarding on the router and using Dyn DNS and configured it correctly, but i cannot browse it from internet.I have also noticed that i am unable to ping the public IP/DynDNS from internet. also i cannot find any option to disable the firewall on my router.
We have had this issue for a long time in our enterprise. I don't work all the time in networking. I did a CCNA a while ago. We used to have a network manager who set everything up but he left the company. Basically we have this issue that if you connect to Cisco L2TP Remote Access VPN you can't access any resources at our Data Center. Also if you connect directly to the LAN.
Basically, my internet claims to be connected (via wire to router, computer isn't wireless enabled.) but when I open a browser (I normally use Chrome but no browser is working) it came up with the Error 105 no matter what address I try to accessSo far, I have tried resetting my router and waiting, using cmd to reset winsock and resetlog, I've fiddled with some of the proxy settings and immediate downloads Of course, I'm not entirely certain what half of those things have done, but nothing seems to have worked properly. I've uninstalled all of the firewall/anti-virus programs I had installed, which hasn't changed anything either.I have had the 'connected but not connected' issue before since it happens quite often, but usually I disable it, restart the computer and just connect again, then it'll work - but this time it hasn't.
I noticed to have the information given from ipconfig/all, so I've copied out what I get from that below.* I've just noticed that the host name has changed to STACYSC, when it's not supposed to be. I think this is from me attempting to connect to a wireless connection before I realised it wasn't enabled - could this be an issue[CODE]
Upgraded my OS from Windows Vista Home Premium to Windows 7 Ultimate. When all was done and over, updates installed and so on I upgraded the Internet Explorer as well from IE 8 (included in the Win 7 install) to IE 9 (I used to have IE 9 before on Vista). A little bit after that I had to uninstall re-install the VPN client for my work and things started going south. Currently after I start the computer the MSN Messenger is not working, the Yahoo messenger is not working, IE, Firefox and Chrome are not working.
IE just hangs, sometimes is displaying [<endif!>] but it seems to find the sites because I can see the icon of the page changinghrome is not able to connect even to google.com but it let's me down nicely (doesn't hog resources like IE does)The Internet connection is fine because I can ping, I can connect to my work's VPN, sometimes even some https pages are briefly working.Once I connect to the VPN everything works great.Now comes the weird part after I connect to the VPN and disconnect, the browsers work, the IM works ... so something gets reset in that process and makes it fine but I have no idea what. (NOTE: IE9 is still barely moving - you request a page go get a snack and maybe it has loaded)
I am using a Dell Latitude E6400 Laptop and have been wirelessly connected to our home internet for several years without any problems. However, of late I have been having problems browsing despite my connection being OK and signal being very good. I am able to still listen to music on spotify, as well as chat on facebook, but cannot load web pages or search for anything on youtube/google etc. I use google chrome but experience the same problem on IE.
I have checked whether it is a problem with malware and have removed all threats, but still the problem persists. the only way I have found of temporarily fixing it is disabling the wireless and reconnecting, whereby it will work perfectly again for anything between 5-50 minutes.I have not changed my router recently so do not think that is the issue. I'm beginning it may just be a hardware fault with the laptop.
I have no admin privileges or access to the router, I have contacted support and they've tried various fixes on their end and just told me it must be a problem on my side. the network registers a mac address under your account name and then assigns an ip.My problem is that my comouter connects to the network fine, and tells me I have internet access, but I can't actually access the internet when I try. I'm definitely connected to the network as i can access the ask4 page that allows me to register a new device, which i access with an ip address of 10.142.0.1 so I'm guessing that's stored locally somewhere on the network. I have tried internet explorer, FireFox and chrome, as well as connecting through game portals and none of them are able to access the internet.
IE gives an error that it says can't be fixed as its an error with the server and Chrome gives error 101 (net::ERR_CONNECTION_RESET). I've tried various fixes, some of which have worked temporarily. After trying most of them I've had internet access that has lasted between 5 minutes and a few hours, but the problem has always returned and the same fix that worked first time hasn't always worked again. I have an xbox that I connect to the same network port in the wall and that accesses the internet perfectly. My computer has 2 Ethernet ports and both have the same problem.
My network adapters are 2 NVIDIA nforce networking controllers (drivers are up to date)When the problem started I was on Windows vista, but I've upgraded to Windows 7 64 bit as an attempt to fix it.I've tried different Ethernet cables, connecting both ports, uninstalling my network adapter drivers, disabling and re-enabling them, resetting my IE settings, disabling and uninstalling my AntiVirus,connecting through an Ethernet switch and disconnecting and reconnecting the cable.
I have router connected to 2 3550 switches directly. 3550A and B switches are running HSRP. OSPF is running between Router and 2 switches.
From Switch B i can ping the Router Wan interface but not the internet sites. from Switch A i can ping any sites?
Switch B 3550SMIB# sh ip routeCodes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1
On the Linksys E4200, the Internet wired connection side, I gave static IP address which is in the same network range as that of LAP2.When tried to ping from LAP1 to LAP2, ping doesnot happen. Any settings by which I can ping from LAP1 to LAP2.
I can not connect to my home wireless network (we did change routers back in Dec and did at that time have problems as well getting it to connect) the router is a Linksys E2000.when I checked further I saw that the IP address was different than the ones on my other laptops so I changed those settings by adding the new IP address..
It is a Dell Inspiron using Windows 7 and the internet has suddenly stopped working on it. It is able to connect to the router fine and says it has a connection but is unable to access anything. And this is accessing the router either wirelessly or wired through an ethernet cable. I know that it is not the router because her roommates are able to access the internet fine and her computer is also unable to access the internet from other networks. Is it possible that the network card in her laptop has died and needs to be replaced? or could it be a corrupted driver? Would using a usb network adapter be a temporary fix? I have searched many forums trying to find an answer but have been unable to.Also a couple times when attempting to see if the wired connection worked I had plugged in the ethernet cable and was able to access google for 5 seconds and then it stopped working, and then unplugging and reconnecting would yield the same results
I can't connect on my 2500 on my xp system. I just wiped the drive and did a fresh install on everything due to a virus. I updated xp/ and drivers and installed the ae2500 drivers. When I try to log on it starts to and shows connected however, it tells me "windows was unable to find a certificate to log you on to the network" I noticed that this system has the same ae2500 with windows vista and uses wpa2-personal, aes. The xp system only has options for wpa-personal, aes. Is this the problem or is it something else?
I am having Inspiron N4010 for almost an year now. I have had many troubles with this but never with internet connectivity. Last week I saw myself not being able to be connected to internet through wireless or wired network while everybody else was connected and surfing. I just thought it to be a small problem and the problem seemed resolved that very day itself on its own.
But today this computer has simply failed to get connected. it does get connected, open a page or two and then again refuses to connect. On the problem diagnoses from network sharing center, it was showing that the websites are not responding, then it started showing that DNS server was not responding while all my setting are correctly configured. I pinged gateway and it responds but on pinging some website there is no response at all. It s a problem with my laptop only as everybody else are using internet very well. I am using internet through my WiFi enabled cell phone using the same connection and router that i use for my laptop. I need an urgent solutions as I have to meet some deadlines regarding assignments.
Internet ISP -> Juniper SRX 210 Ge-0/0/0 Juniper fe0/0/2 -> Cisco ASA 5505 Cisco ASA 5505 - >Inernal LAN switch.
1. Internet is connected to Juniper Ge0/0/0 via /30 IP.
2. Juniper fe0/0/2 port is configured as inet port and configured the Internal public LAN pool provided by the ISP. And this port is directly connected to Cisco ASA 5505 E0/0. Its a /28 pool IP address. This interface is configured as outside and security level set to 0.
From Juniper SRX, am able to ping public Internet IPs (8.8.8.8).
Issue:
1. From ASA am unable to ping public ip configured on Juniper G0/0/0 port.(/30) 2. From ASA no other Public internet IP is pinging.
Troubleshooting Done so far.
1, Configured icmp inspection on ASA. 2. Used the packet tracer in ASA, it shows the packet is flowing outside without a drop. 3. Allowed all services in untrust zone in bound traffic in Juniper SRX. 4. Viewed the logs when I was trying the ping 8.8.8.8 in ASA. It says "Tear down ICMP connection for faddrr **** gaddr **
I got a trojan and removed most of it with Malware Bytes. My computer was still acting squirrely so I read that I needed to delete a ping file. I did and can no longer connect to the internet. It just sits and tries to acquire the IP address. I have reset my winsock and tried uninstalling and reinstalling my network drivers etc..
I can connect to the internet after 5mins or so after booting up but after that internet will not respond at all.i need to restart again my PC in order to connect again to the internet i somehow manage to bump with this solution using ping command.whenever i boot my pc i need to open this command and i can surf the internet without getting my connection lost just as long ping command is open.
I have bought a 861w to replace my 877w. We switched from telco(ADSL) to Cable due to faster speeds for up and down. My current physical setup is as such. Cable modem is a straight trough with 4 lan port in the back. Al lan ports are configured by the cable company for my assigned public ip’s. (24.x.x.2 through .6 – 255.255.255.x) I also have my assigned gateway as 24.x.x.1
My goal is to setup the new router same as the old one so all interfaces (e0 to e3) use a Vlan1 and Bridge Bvi1 to get the traffic go through e4 which is my WAN port on 861. I am not even concerned abt the wireless because I can’t get this to work. I am attaching the running config on the old 877 and 861 so you all can see what it was and what I am trying to do. As of now I am so confused that my head is spinning……I am able to ping out and ping e4 from outside but I am not able to connect any pc’s or node and connect to net from inside on any of e0 to e3.
I cannot access any internet browsers. My OS is Vista and I use Verizon Fios. My computer is hooked up to my modem via ethernet cable.I have no computer and am chilling at friends house to use his internet on his lap top.
I've created two configurations. One for the router side and one for the AP point side. However, I am having trouble getting the internal AP to bridge to the router properly. It is my understanding that the Wlan-GigabitEthernet is the internal interface connecting to the AP and the BVI1 together. I can't ping any ip address on the router side from the ap and the radio is active and we can see it but it seems that it doesn't give an ip address. [code] Is it a VLan issue or an ip issue but I could use a second opinion. I've included both configurations.
we are having some trouble setting up our router (Cisco 861W) webserver on the LAN so that it can be accessed from outside (http via port 80). When we try to access it via the web address, we just get the login window of the Cisco router software?
I have tried everything (to the best of my knowledge). I have tried stopping certain programmes from launching from start up (using msconfig.exe) and deselecting unnecessary programmes.The internet works in Safe Mode with Networking and I have run Malwarebytes Anti-Malware but to no-avail.The router is working because my iPad and other PC's are connected to the same network and are all operating perfectly. I am running on a wireless network and tried an ethernet connectinon but again noI have seen on a few forums that when people provide their HijackThis logs.[CODE]
I'm connecting to the internet using a wireless connection but i can't go online on either of my messengers nor go on the web using any of my browser but i can download things using my torrent programs(Bitcomet),I'm using an Acer laptop with 4gb DDR3 and Win 7.
